|
INDEX
<br />SECTION 01100 - SUMMARY
<br />SECTION 01250 - CONTRACT MODIFICATION PROCEDURES
<br />SECTION 01290 - PAYMENT PROCEDURES
<br />SECTION 01310 - PROJECT MANAGEMENT AND COORDINATION
<br />SECTION 01320 - CONSTRUCTION PROGRESS DOCUMENTATION
<br />SECTION 01330 - SUBMITTAL PROCEDURES
<br />SECTION 01400 - QUALITY REQUIREMENTS
<br />SECTION 01500 - TEMPORARY FACILITIES AND CONTROLS
<br />SECTION 01770 - CLOSEOUT PROCEDURES
<br />SECTION 02361- TERMITE CONTROL
<br />SECTION 03300 - CAST -IN -PLACE CONCRETE
<br />SECTION 06100 - ROUGH CARPENTRY
<br />SECTION 07210 - BUILDING INSULATION
<br />SECTION 07920 - JOINT SEALANTS
<br />SECTION 08110 - STEEL DOORS AND FRAMES
<br />SECTION 08211- FLUSH WOOD DOORS
<br />SECTION 08410 -ALUMINUM ENTRANCES AND STOREFRONTS
<br />SECTION 08800 - GLAZING
<br />SECTION 09260 - GYPSUM BOARD ASSEMBLIES
<br />SECTION 09512 - ACOUSTICAL TILE CEILINGS
<br />SECTION 09653 - RESILIENT WALL BASE AND ACCESSORIES
<br />SECTION 09900 - PAINT AND WALL FINISHES
<br />SECTION 10801- TOILET AND BATH ACCESSORIES
<br />SECTION 01100 - SUMMARY
<br />PART 1 - GENERAL
<br />1.1 WORK COVERED BY CONTRACT DOCUMENTS
<br />A. Project Identification: Tenant B7 in Building B at Zephyr Commons
<br />1. Project Location: 7932 Gall Bvld, Zephyrhills, FL.
<br />2. Owner: Primerica Group One, Inc
<br />B. The Work consists of approximately 1,200 SF of "vanilla box" interior buildout inside an existing shell building.
<br />C. Project will be constructed under a general construction contract.
<br />1.2 WORK SEQUENCE
<br />A. The Work shall be conducted in one phase on a schedule that is mutually agreed on by the contractor and owner.
<br />1.3 USE OF PREMISES
<br />A. General: Contractor shall have full use of premises for construction operations, including use of Project site, during construction
<br />period. Contractor's use of premises is limited only by Owner's right to perform work or to retain other contractors on portions of
<br />Project.
<br />B. Cooperate fully with separate contractors so work on those contracts may be carried out smoothly, without interfering with or
<br />delaying work under this Contract.
<br />END OF SECTION 01100
<br />SECTION 01250 - CONTRACT MODIFICATION PROCEDURES
<br />PART 1 - GENERAL -
<br />1.1 PROPOSAL REQUESTS
<br />A. Owner -Initiated Proposals. Do not consider proposed changes as instructions either to stop work in progress or to execute the
<br />proposed change, unless told by the owner in writing to do so. Within 14 days, submit a quotation estimating cost adjustments to
<br />the Contract Sum and the Contract Time necessary to execute the change. Include a list of all changes to quantities of prod-
<br />ucts. Indicate applicable taxes, delivery charges, and equipment rentals. And, include an updated Contractor's Construction
<br />Schedule.
<br />B. Contractor -Initiated Proposals: If latent or unforeseen conditions require modifications to the Contract, Contractor may propose
<br />changes by submitting a request for a change. Use AIA Document G709.
<br />1.3 CHANGE ORDER PROCEDURES
<br />A. On Owner's approval of a Proposal Request, Contractor will issue a Change Order for signatures of Owner and Contractor on AIA
<br />Document G701.
<br />END OF SECTION 01250
<br />SECTION 01290 - PAYMENT PROCEDURES
<br />PART 1 - GENERAL
<br />1.1 SUMMARY
<br />A. This Section specifies administrative and procedural requirements necessary to prepare and process Applications for Payment.
<br />1.2 SCHEDULE OF VALUES
<br />A. Contractor shall prepare a schedule of values that is coordinated with the Contractor's Construction Schedule. The contractor shall
<br />submit the schedule of values to the owner for approval prior to starting the work.
<br />1.3 APPLICATIONS FOR PAYMENT
<br />A. Application for Payment shall Use AIA Documents G702 and G703.
<br />B. Notarize and execute the forms by a person authorized to sign legal documents on behalf of Contractor. Submit the forms along
<br />with waivers of lien directly to the owner for approval. Include waivers of lien.
<br />C. Waivers of Mechanic's Lien: With each Application for Payment, submit waivers of mechanic's lien from every entity who is
<br />lawfully entitled to file a mechanic's lien arising out of the Contract and related to the Work covered by the payment.
<br />D. Final Payment Application: Submit final Application for Payment with releases and supporting documentation not previously
<br />submitted and accepted, including, but not limited, to the following:
<br />1. Evidence of completion of Project closeout requirements.
<br />2. Insurance certificates for products and completed operations where required and proof that taxes, fees, and similar obliga-
<br />tions were paid.
<br />3. Updated final statement, accounting for final changes to the Contract Sum.
<br />4. AIA Document G706, "Contractor's Affidavit of Payment of Debts and Claims."
<br />5. AIA Document G706A, "Contractor's Affidavit of Release of Liens."
<br />6. AIA Document G707, "Consent of Surety to Final Payment."
<br />7. Evidence that claims have been settled.
<br />8. Final meter readings for utilities, a measured record of stored fuel, and similar data as of date of Substantial Completion or
<br />when Owner took possession of and assumed responsibility for corresponding elements of the Work.
<br />END OF SECTION 01290
<br />SECTION 01310 - PROJECT MANAGEMENT AND COORDINATION
<br />PART 1 - GENERAL
<br />1.1 PROJECT MEETINGS
<br />A. Schedule and conduct meetings at the Project site to coordinate subcontractors and update progress. This meetings should be
<br />weekly and as required to coordinate the work. Make the owner aware of these meetings in advance. Keep minutes of these meet-
<br />ings and forward copies to the owner and architect for their record.
<br />B. Preconstruction Conference: Schedule a preconstruction conference before starting construction, at a time convenient to Owner.
<br />END OF SECTION 01310
<br />SECTION 01320 - CONSTRUCTION PROGRESS DOCUMENTATION
<br />PART 1 - GENERAL
<br />1.1 CONTRACTOR'S CONSTRUCTION SCHEDULE
<br />A. Contractor's Construction Schedule Updating: At intervals appropriate to the construction, update schedule to reflect actual con-
<br />struction progress and activities. Issue schedule before each regularly scheduled progress meeting.
<br />END OF SECTION 01320
<br />SECTION 01330 - SUBMITTAL PROCEDURES
<br />PART 1 - GENERAL
<br />1.1 SUMMARY
<br />A. All submittals shall be sent directly to the owner for approval. No submittals should be sent directly to the architect.
<br />B. Submittals are only required for items that are aesthetic in nature. This includes, but is not limited to paint colors, ceiling tile, VCT,
<br />vinyl base, and door hardware. All finishes shall be selected by the owner from submittals prepared by the contractor.
<br />C. Submittals are required for any items where the contractor wishes to deviate from the construction drawings. These submittals
<br />must be sent directly to the owner for approval.
<br />D. Prior to starting construction, the contractor shall review the entire bill of materials with the owner to determine what items will
<br />need the owner's approval prior to purchase.
<br />END OF SECTION 01330
<br />SECTION 01400 - QUALITY REQUIREMENTS
<br />PART 1 - GENERAL
<br />1.1 SUMMARY
<br />A. This Section includes administrative and procedural requirements for quality assurance and quality control.
<br />B. Testing and inspecting services are required to verify compliance with requirements specified or indicated. These services do not
<br />relieve Contractor of responsibility for compliance with the Contract Document requirements.
<br />1. Specified tests, inspections, and related actions do not limit Contractor's quality -control procedures that facilitate compli-
<br />ance with the Contract Document requirements.
<br />Owner, r authorities havin 'urisdic-
<br />2. Requirements for Contractor to provide qualitycontrol services required by Architect, Ow e , o a s g �
<br />tion are not limited by provisions of this Section.
<br />1.2 DEFINITIONS
<br />A. Quality -Assurance Services: Activities, actions, and procedures performed before and during execution of the Work to guard
<br />against defects and deficiencies and ensure that proposed construction complies with requirements.
<br />B. Quality -Control Services: Tests, inspections, procedures, and related actions during and after execution of the Work to evaluate
<br />that completed construction complies with requirements. Services do not include contract enforcement activities performed by
<br />Architect.
<br />C. Mockups: Full-size, physical example assemblies to illustrate finishes and materials. Mockups are used to verify selections made
<br />under Sample submittals, to demonstrate aesthetic effects and, where indicated, qualities of materials and execution, and to review
<br />construction, coordination, testing, or operation; they are not Samples. Mockups establish the standard by which the Work will be
<br />judged.
<br />D. Testing Agency: An entity engaged to perform specific tests, inspections, or both. Testing laboratory shall mean the same as test-
<br />ing agency.
<br />1.3 SUBMITTALS
<br />A. Reports: Prepare and submit certified written reports that include the following:
<br />1. Date of issue.
<br />2. Project title and number.
<br />3. Name, address, and telephone number of testing agency.
<br />4. Dates and locations of samples and tests or inspections.
<br />5. Names of individuals making tests and inspections.
<br />6. Description of the Work and test and inspection method.
<br />7. Identification of product and Specification Section.
<br />8. Complete test or inspection data.
<br />9. Test and inspection results and an interpretation of test results.
<br />10. Ambient conditions at time of sample taking and testing and inspecting.
<br />11. Comments or professional opinion on whether tested or inspected Work complies with the Contract Document require-
<br />ments.
<br />12. Name and signature of laboratory inspector.
<br />. 13. Recommendations on retesting and reinspecting.
<br />B. Permits, Licenses, and Certificates: For Owner's records, submit copies of permits, licenses, certifications, inspection reports,
<br />releases, jurisdictional settlements, notices, receipts for fee payments, judgments, correspondence, records, and similar documents,
<br />established for compliance with standards and regulations bearing on performance of the Work.
<br />1.5 QUALITY ASSURANCE
<br />A. Fabricator Qualifications: A firm experienced in producing products similar to those indicated for this Project and with a record of
<br />successful in-service performance, as well as sufficient production capacity to produce required units.
<br />B. Factory -Authorized Service Representative Qualifications: An authorized representative of manufacturer who is trained and
<br />approved by manufacturer to inspect installation of manufacturer's products that are similar in material, design, and extent to those
<br />indicated for this Project.
<br />C. Installer Qualifications: A firm or individual experienced in installing, erecting, or assembling work similar in material, design,
<br />and extent to that indicated for this Project, whose work has resulted in construction with a record of successful in-service perfor-
<br />mance.
<br />D. Manufacturer Qualifications: A firm experienced in manufacturing products or systems similar to those indicated for this Project
<br />and with a record of successful in-service performance.
<br />E. Professional Engineer Qualifications: A professional engineer who is legally qualified to practice in jurisdiction where Project is
<br />located and who is experienced in providing engineering services of the kind indicated. Engineering services are defined as those
<br />. performed for installations of the system, assembly, or product that are similar to those indicated for this Project in material, design,
<br />and extent.
<br />F. Specialists: Certain sections of the Specifications require that specific construction activities shall be performed by entities who
<br />are recognized experts in those operations. Specialists shall satisfy qualification requirements indicated and shall be engaged for
<br />the activities indicated.
<br />1. Requirement for specialists shall not supersede building codes and similar regulations governing the Work, nor interfere
<br />with local trade -union jurisdictional settlements and similar conventions.
<br />G. Testing Agency Qualifications: An agency with the experience and capability to conduct testing and inspecting indicated, as docu-
<br />mented by ASTM E 548, and that specializes in types of tests and inspections to be performed.
<br />1.6 QUALITY CONTROL
<br />A. Owner Responsibilities: Where quality -control services are indicated as Owner's responsibility, Owner will engage a qualified
<br />testing agency to perform these services.
<br />1. Owner will furnish Contractor with names, addresses, and telephone numbers of testing agencies engaged and a description
<br />of the types of testing and inspecting they are engaged to perform.
<br />2. Costs for retesting and reinspecting construction that replaces or is necessitated by work that failed to comply with the Con-
<br />tract Documents will be charged to Contractor.
<br />B. Contractor Responsibilities: Unless otherwise indicated, provide quality -control services specified and required by authorities
<br />having jurisdiction.
<br />1. Where services are indicated as Contractor's responsibility, engage a qualified testing agency to perform these quality -
<br />control services.
<br />a. . Contractor shall not employ the same entity engaged by Owner, unless agreed to in writing by Owner.
<br />2. Notify testing agencies at least 24 hours in advance of time when Work that requires testing or inspecting will be per-
<br />formed.
<br />3. Where quality -control services are indicated as Contractor's responsibility, submit a certified written report, in duplicate, of
<br />each quality -control service.
<br />4. Testing and inspecting requested by Contractor and not required by the Contract Documents are Contractor's responsibil-
<br />ity.
<br />5. Submit additional copies of each written report directly to authorities having jurisdiction, when they so direct.
<br />C. Manufacturer's Field Services: Where indicated, engage a factory -authorized service representative to inspect field -assembled
<br />components and equipment installation, including service connections. Report results in writing.
<br />D. Retesting/Reinspecting: Regardless of whether original tests or inspections were Contractor's responsibility, provide quality -
<br />control services, including retesting and reinspecting, for construction that revised or replaced Work that failed to comply with
<br />requirements established by the Contract Documents.
<br />E. Testing Agency Responsibilities: Cooperate with Architect and Contractor in performance of duties. Provide qualified personnel
<br />to perform required tests and inspections.
<br />1. Notify Architect and Contractor promptly of irregularities or deficiencies observed in the Work during performance of its
<br />services.
<br />2. Interpret tests and inspections and state in each report whether tested and inspected work complies with or deviates from
<br />requirements.
<br />3. Submit a certified written report, in duplicate, of each test, inspection, and similar quality -control service through Contrac-
<br />tor.
<br />4. Do not release, revoke, alter, or increase requirements of the Contract Documents or approve or accept any portion of the
<br />Work.
<br />5. Do not perform any duties of Contractor.
<br />END OF SECTION 01400
<br />SECTION 01500 - TEMPORARY FACILITIES AND CONTROLS
<br />PART 1 - GENERAL
<br />1.1 SUMMARY
<br />A. This Section includes requirements for temporary facilities and controls, including temporary utilities, support facilities, and secu-
<br />rity and protection facilities.
<br />1.2 USE CHARGES
<br />A. General: Cost or use charges for temporary facilities are not chargeable to Owner or Architect and shall be included in the Contract
<br />Sum. .
<br />B. Sewer Service: Pay sewer service use charges for sewer usage, by all parties engaged in construction, at Project site.
<br />C. Water Service: Pay water service use charges, whether metered or otherwise, for water used by all entities engaged in construction
<br />activities at Project site.
<br />D. Electric Power Service: Pay electric power service use charges, whether metered or otherwise, for electricity used by all entities
<br />engaged in construction activities at Project site.
<br />1.3 QUALITY ASSURANCE
<br />A. Standards: Comply with ANSI A 10.6, NECA's "Temporary Electrical Facilities," and NFPA 241.
<br />1. Trade Jurisdictions: Assigned responsibilities for installation and operation of temporary utilities are not intended to inter-
<br />fere with trade regulations and union jurisdictions.
<br />2. Electric Service: Comply with NECA, NEMA, and UL standards and regulations for temporary electric service. Install
<br />service to comply with NFPA 70.
<br />B. Tests and Inspections: Arrange for authorities having jurisdiction to test and inspect each temporary utility before use. Obtain
<br />required certifications and permits.
<br />PART 2 - PRODUCTS
<br />2.1 EQUIPMENT
<br />A. General: Provide equipment suitable for use intended.
<br />B. Fire Extinguishers: Hand carried, portable, UL rated. Provide class and extinguishing agent as indicated or a combination of
<br />extinguishers of NFPA-recommended classes for exposures in quantities and locations determined by regulation of any authority
<br />having jurisdiction.
<br />1. Comply with NFPA 10 and NFPA 241 for classification, extinguishing agent, and size required by location and class of fire
<br />exposure.
<br />C. Self -Contained Toilet Units: Single -occupant units of chemical, aerated recirculation, or combustion type; vented; fully enclosed
<br />with a glass -fiber -reinforced polyester shell or similar nonabsorbent material in quantities and locations determined by regulation
<br />of any authority having jurisdiction
<br />D. Drinking -Water Fixtures: Drinking -water fountains or Containerize tap -dispenser, bottled -water drinking -water units including
<br />g g dg g
<br />paper cup supply in quantities and locations determined by regulation of any authority having jurisdiction
<br />E. Electrical Outlets: Properly configured, NEMA-polarized outlets to prevent insertion of I I0- to 120-V plugs into higher -voltage
<br />outlets; equipped with ground -fault circuit interrupters, reset button, and pilot light.
<br />F. Power Distribution System Circuits: Where permitted and overhead and exposed for surveillance, wiring circuits, not exceeding
<br />125-V ac, 20-A rating, and lighting circuits may be nonmetallic sheathed cable.
<br />PART 3 - EXECUTION
<br />3.1 INSTALLATION, GENERAL
<br />A. Locate facilities where they will serve Project adequately and result in minimum interference with performance of the Work. Relo-
<br />cate and modify facilities as required.
<br />B. Provide each facility ready for use when needed to avoid delay. Maintain and modify as required. Do not remove until facilities
<br />are no longer needed or are replaced by authorized use of completed permanent facilities.
<br />3.2 TEMPORARY UTILITY INSTALLATION
<br />A. General: Engage appropriate local utility company to install temporary service or connect to existing service. Where utility com-
<br />pany provides only part of the service, provide the remainder with matching, compatible materials and equipment. Comply with
<br />utility company recommendations.
<br />1. Arrange with utility company, Owner, and existing users for time when service can be interrupted, if necessary, to make
<br />connections for temporary services.
<br />2. Provide adequate capacity at each stage of construction. Before temporary utility is available, provide trucked -in services.
<br />B. Sewers and Drainage: If sewers are available, provide temporary connections to remove effluent that can be discharged lawfully.
<br />If sewers are not available or cannot be used, provide drainage ditches, dry wells, stabilization ponds, and similar facilities. If
<br />neither sewers nor drainage facilities can be lawfully used for discharge of effluent, provide containers to remove and dispose of
<br />effluent off -site in a lawful manner.
<br />C. Water Service: Install water service and distribution piping in sizes and pressures adequate for construction until permanent water
<br />service is in use. Sterilize temporary water piping before use.
<br />D. Sanitary Facilities: Provide temporary toilets, wash facilities, and drinking -water fixtures. Comply with regulations and health
<br />codes for type, number, location, operation, and maintenance of fixtures and facilities.
<br />E. Heating and Cooling: Provide temporary heating and cooling required by construction activities for curing or drying of completed
<br />installations or for protecting installed construction from adverse effects of low temperatures or high humidity.
<br />1. Maintain a minimum temperature of 50 deg F in permanently enclosed portions of building for normal construction activi-
<br />ties, and 65 deg F for finishing activities and areas where finished Work has been installed.
<br />F. Ventilation and Humidity Control: Provide temporary ventilation required by construction activities for curing or drying of com-
<br />pleted installations or for protecting installed construction from adverse effects of high humidity. .
<br />G: Electric Power Service: Provide weatherproof, grounded electric power service and distribution system of sufficient size, capac-
<br />ity, and power characteristics during construction period. Include meters, transformers, overload -protected disconnecting means,
<br />automatic ground -fault interrupters, and main distribution switchgear.
<br />H. Lighting: Provide temporary lighting with local switching that provides adequate illumination for construction operations and
<br />traffic conditions. .
<br />1. Telephone Service: Provide temporary telephone service throughout construction period for common -use facilities used by all
<br />personnel .engaged in construction activities. .
<br />1. Provide additional telephone lines for the following:
<br />a. Provide a dedicated telephone line for each facsimile machine and computer with modem in each field office.
<br />2. Provide an answering machine on superintendent's telephone.
<br />3. Provide a facsimile machine for site use
<br />4. Provide a portable cellular telephone for superintendent's use in making and receiving telephone calls when away from field
<br />`office.
<br />3.3 SUPPORT FACILITIES INSTALLATION
<br />A. General: Comply with the following:
<br />1. Locate field offices, storage sheds, sanitary facilities, and other temporary construction and support facilities for easy access,
<br />making them accessible for handicap access where required by the authority having jurisdiction.
<br />2. Maintain support facilities until near Substantial Completion. Remove before Substantial Completion. Personnel remain-
<br />ing after Substantial Completion will be permitted to use permanent facilities, under conditions acceptable to Owner.
<br />3.4 OPERATION, TERMINATION, AND REMOVAL
<br />A. Termination and Removal: Remove each temporary facility when need for its service has ended, when it has been replaced by
<br />authorized use of a permanent facility, or no later than Substantial Completion. Complete or, if necessary, restore permanent
<br />construction that may have been delayed because of interference with temporary facility. Repair damaged Work, clean exposed
<br />surfaces, and replace construction that cannot be satisfactorily repaired.
<br />1. Materials and facilities that constitute temporary facilities are the property of Contractor. Owner reserves right to take pos-
<br />session of Project identification signs.
<br />2. Remove temporary paving not intended for or acceptable for integration into permanent paving. Where area is intended for
<br />landscape development, remove soil and aggregate fill that do not comply with requirements for fill or subsoil. Remove
<br />materials contaminated with road oil, asphalt and other petrochemical compounds, and other substances that might impair
<br />growth of plant materials or lawns. Repair or replace street paving, curbs, and sidewalks at temporary entrances, as required
<br />by authorities having jurisdiction.
<br />3. At Substantial Completion, clean and renovate permanent facilities used during construction period. Comply with final
<br />cleaning requirements in Division 1 Section "Closeout Procedures."
<br />END OF SECTION 01500
<br />SECTION 01770 - CLOSEOUT PROCEDURES
<br />PART 1 - GENERAL
<br />1.1 SUMMARY
<br />A. This Section includes administrative and procedural requirements for contract closeout, including, but not limited to, the follow-
<br />ing:
<br />1. Inspection procedures.
<br />2. Project Record Documents.
<br />3. Operation and maintenance manuals.
<br />4. Warranties.
<br />5. Instruction of Owner's personnel.
<br />6. Final cleaning.
<br />1.2 SUBSTANTIAL COMPLETION
<br />A. Preliminary Procedures: Before requesting inspection for determining date of Substantial Completion, complete the following.
<br />List items below that are incomplete in request.
<br />1. Prepare a list of items to be completed and corrected (punch list), the value of items on the list, and reasons why the Work
<br />is not complete.
<br />2. Advise Owner of pending insurance changeover requirements.
<br />3. Submit specific warranties, workmanship bonds, maintenance service agreements, final certifications, and similar docu-
<br />ments.
<br />4. Obtain and submit releases permitting Owner unrestricted use of the Work and access to services and utilities. Include
<br />occupancy permits, operating certificates, and similar releases.
<br />5. Prepare and submit Project Record Documents, operation and maintenance manuals, property surveys, and similar final
<br />record information.
<br />6. Deliver tools, spare parts, extra materials, and similar items to location designated by Owner. Label with manufacturer's
<br />name and model number where applicable.
<br />7. Make final changeover of permanent locks and deliver keys to Owner. Advise Owner's personnel of changeover in security
<br />provisions.
<br />8. Complete startup testing of systems.
<br />9. Submit test/adjust/balance records.
<br />10. Terminate and remove temporary facilities from Project site, along with mockups, construction tools, and similar ele-
<br />ments.
<br />11. Advise Owner of changeover in heat and other utilities.
<br />12. Submit changeover information related to Owner's occupancy, use, operation, and maintenance.
<br />13. Complete final cleaning requirements, including touchup painting.
<br />14. Touch up and otherwise repair and restore marred exposed finishes to eliminate visual defects.
<br />1.3 FINAL COMPLETION
<br />A. Preliminary Procedures: Before requesting final inspection for determining date of Final Completion, complete the following:
<br />1. Submit a final Application for Payment according to Division 1 Section "Payment Procedures."
<br />2. Submit certified copy of Architect's Substantial Completion inspection list of items to be completed or corrected (punch
<br />lit endorsed and dated b Architect. The certified co of the list shall state that each item has been completed or other-
<br />wise e y copy p
<br />wise resolved for acceptance.
<br />3. Submit evidence of final, continuing insurance coverage complying with insurance requirements.
<br />4. Submit pest -control final inspection report and warranty.
<br />5. Instruct Owner's personnel in operation, adjustment, and maintenance of products, equipment, and systems.
<br />1.4 PROJECT RECORD DOCUMENTS
<br />A. General: Do not use Project Record Documents for construction purposes. Protect Project Record Documents from deterioration
<br />and loss. Provide access to Project Record Documents for Architect's reference during normal working hours.
<br />B. Record Drawings: Maintain and submit one set of blue- or black -line white prints of Contract Drawings and Shop Drawings.
<br />1.6
<br />C.
<br />A.
<br />B.
<br />1.7
<br />A.
<br />B.
<br />C.
<br />PART 2-
<br />2.1
<br />A.
<br />PART 3 -
<br />3.1
<br />A.
<br />1. Mark Record Prints to show the actual installation where installation varies from that shown originally. Require individual
<br />or entity who obtained record data, whether individual or entity is Installer, subcontractor, or similar entity, to prepare the
<br />marked -up Record Prints.
<br />a. Give particular attention to information on concealed elements that cannot be readily identified and recorded later.
<br />b. Record data as soon as possible after obtaining it. Record and check the markup before enclosing concealed instal-
<br />lations.
<br />2. Mark record sets with erasable, red -colored pencil. Use other colors to distinguish between changes for different categories
<br />of the Work at the same location.
<br />3. Note Construction Change Directive numbers, Change Order numbers, alternate numbers, and similar identification where
<br />applicable.
<br />4. Identify and date each Record Drawing; include the designation "PROJECT RECORD DRAWING" in a prominent location.
<br />Organize into manageable sets; bind each set with durable paper cover sheets. Include identification on cover sheets.
<br />Miscellaneous Record Submittals: Assemble miscellaneous records required by other Specification Sections for miscellaneous
<br />record keeping and submittal in connection with actual performance of the Work. Bind or file miscellaneous records and identify
<br />each, ready for continued use and reference.
<br />OPERATION AND MAINTENANCE MANUALS
<br />Assemble a complete set of operation and maintenance data indicating the operation and maintenance of each system, subsystem,
<br />and piece of equipment not part of a system. Include operation and maintenance data required in individual Specification Sections
<br />and as follows:
<br />1. Operation Data: Include emergency instructions and procedures, system and equipment descriptions, operating procedures,
<br />and sequence of operations.
<br />2. Maintenance Data: Include manufacturer's information, list of spare parts, maintenance procedures, maintenance and ser-
<br />vice schedules for preventive and routine maintenance, and copies of warranties and bonds.
<br />Organize operation and maintenance manuals into suitable sets of manageable size. Bind and index data in heavy-duty, three-
<br />ring, vinyl -covered, loose-leaf binders, in thickness necessary to accommodate contents, with pocket inside the covers to receive
<br />folded oversized sheets. Identify each binder on front and spine with the printed title "OPERATION AND MAINTENANCE
<br />MANUAL," Project name, and subject matter of contents.
<br />WARRANTIES
<br />Submittal Time: Submit written warranties on request of Architect for designated portions of the Work where commencement of
<br />warranties other than date of Substantial Completion is indicated.
<br />Organize warranty documents into an orderly sequence based on the table of contents of the Project Manual.
<br />1. Bind warranties and bonds in heavy-duty, 3-ring, vinyl -covered, loose-leaf binders, thickness as necessary to accommodate
<br />contents.
<br />2. Provide heavy paper dividers with plastic -covered tabs for each separate warranty. Mark tab to identify the product or
<br />installation. Provide a typed description of the product or installation, including the name of the product and the name,
<br />address, and telephone number of Installer.
<br />3. Identify each binder on the front and spine with the typed or printed title "WARRANTIES," Project name, and name of
<br />Contractor.
<br />Provide additional copies of each warranty to include in operation and maintenance manuals.
<br />PRODUCTS
<br />MATERIALS
<br />Cleaning Agents: Use cleaning materials and agents recommended by manufacturer or fabricator of the surface to be cleaned. Do
<br />not use cleaning agents that are potentially hazardous to health or property or that might damage finished surfaces.
<br />EXECUTION
<br />FINAL CLEANING
<br />Cleaning: Employ experienced workers or professional cleaners for final cleaning. Clean each surface or unit to condition
<br />expected in an average commercial building cleaning and maintenance program. Comply with manufacturer's written instruc-
<br />tions.
<br />1. Complete the following cleaning operations before requesting inspection for certification of Substantial Completion for
<br />entire Project or for a portion of Project:
<br />a.
<br />Clean Project site, yard, and grounds, in areas disturbed by construction activities, including landscape development
<br />areas, of rubbish, waste material, litter, and other foreign substances. .
<br />b.
<br />Sweep paved areas broom clean. Remove petrochemical spills, stains, and other foreign deposits.
<br />C.
<br />Rake grounds that are neither planted nor paved to a smooth, even -textured surface.
<br />d.
<br />Remove tools, construction equipment, machinery, and surplus material from Project site.
<br />e.
<br />Clean exposed exterior and interior hard -surfaced finishes to a dirt -free condition, free of stains, films, and similar
<br />foreign substances. Avoid disturbing natural weathering of exterior surfaces. Restore reflective surfaces to their
<br />original condition.
<br />f.
<br />Remove debris and surface dust from limited access spaces, including roofs, plenums, shafts, trenches, equipment
<br />vaults, manholes, attics, and similar spaces.
<br />g.
<br />Sweep concrete floors broom -clean in unoccupied spaces.
<br />h.
<br />Vacuum carpet and similar soft surfaces, removing debris and excess nap; shampoo if visible soil or stains remain.
<br />i.
<br />Clean transparent materials, including mirrors and glass in doors and windows. Remove glazing compounds and
<br />other noticeable, vision -obscuring materials. Replace chipped or broken glass and other damaged transparent materi-
<br />als. Polish mirrors and glass, taking care not to scratch surfaces.
<br />j.
<br />Remove labels that are not permanent.
<br />k.
<br />Touch up and otherwise repair and restore marred, exposed finishes and surfaces. Replace finishes and surfaces that
<br />cannot be satisfactorily repaired or restored or that already show evidence of repair or restoration.
<br />2) 1) Do not paint over "UL" and similar labels, including mechanical and electrical nameplates.
<br />1.
<br />Wipe surfaces of mechanical and electrical equipment and similar equipment. Remove excess lubrication, paint and
<br />mortar droppings, and other foreign substances.
<br />in.
<br />Replace parts subject to unusual operating conditions.
<br />n.
<br />Clean plumbing fixtures to a sanitary condition, free of stains, including stains resulting from water exposure.
<br />o.
<br />Replace disposable air filters and clean permanent air filters. Clean exposed surfaces of diffusers, registers, and
<br />grills.
<br />p.
<br />Clean light fixtures, lamps, globes, and reflectors to function with full efficiency. Replace burned -out bulbs, and
<br />those noticeably dimmed by hours of use, and defective and noisy starters in fluorescent and mercury vapor fixtures
<br />to comply with requirements for new fixtures. .
<br />q.
<br />Leave Project clean and ready for occupancy.
<br />B. Comply with safety standards for cleaning. Do not burn waste materials. Do not bury debris or excess materials on Owner's
<br />property. Do not discharge volatile, harmful, or dangerous materials into drainage systems. Remove waste materials from Project
<br />site and dispose of lawfully.
<br />END OF SECTION 01770
<br />SECTION 02361- TERMITE CONTROL -
<br />PART 1 - GENERAL
<br />1.1 SUMMARY
<br />A. This Section includes soil treatment for termite control.
<br />1.2 SUBMITTALS
<br />A. Product Data: For each product indicated, including EPA -Registered Label.
<br />B. Product certificates.
<br />1.3 QUALITY ASSURANCE
<br />A. Applicator Qualifications: A pest control operator who is licensed according to regulations of authorities having jurisdiction to
<br />apply termite control treatment in jurisdiction where Project is located.
<br />B. Regulatory Requirements: Formulate and apply termiticides, and label with a Federal registration number, to comply with EPA
<br />regulations and authorities having jurisdiction.
<br />1.4 WARRANTY
<br />A. Soil Termiticide Special Warranty: Manufacturer's standard form, signed by applicator and Contractor, certifying that applied soil
<br />tenniticide treatment will prevent infestation of subterranean termites. If subterranean termite activity or damage is discovered
<br />within 5 years from date of Substantial Completion, re -treat soil and repair or replace damage caused by termite infestation.
<br />PART 2 - PRODUCTS
<br />2.1 TERMITE CONTROL
<br />A. Soil Treatment: EPA -registered termiticide complying with requirements of authorities having jurisdiction, in a soluble or emul-
<br />sible, concentrated formulation that dilutes with water or foaming agent. Use only soil treatment solutions that are not harmful to
<br />plants.
<br />1. Available Manufacturers: Subject to compliance with requirements, manufacturers offering products that may be incorpo-
<br />rated into the Work include, but are not limited to, the following:
<br />a. AgrEvo Environmental Health, Inc.; a company of Hoechst and Schering, Berlin.
<br />b. Bayer Corp.; Garden & Professional Care.
<br />C. DowElanco.
<br />PART 3 - EXECUTION
<br />3.1 SOIL TREATMENT APPLICATION
<br />A. Apply soil treatment at the label volume and rate for the maximum termiticide concentration allowed for each specific use, accord-
<br />ing to the product's EPA -Registered Label.
<br />l . Mix termiticide solution to a uniform consistency.
<br />2. Apply to produce a continuous horizontal and vertical termiticidal barrier or treated zone around and under building con-
<br />struction. Distribute the treatment evenly.
<br />3. Slabs -on -Grade and Basement Slabs: Under ground -supported slab construction, including footings, building slabs, and
<br />attached slabs as an overall treatment. Treat soil materials before concrete footings and slabs are placed.
<br />4. Foundations: Adjacent soil including soil along entire inside perimeter of foundation walls, along both sides of interior
<br />partition walls, around plumbing pipes and electric conduit penetrating slab, and around interior column footers, piers, and
<br />chimney bases; and along entire outside perimeter, from grade to bottom of footing. Avoid soil washout around footings.
<br />5. Crawlspaces: Soil under and adjacent to foundations. Treat adjacent areas including around entrance platform, porches, and
<br />equipment bases. Apply overall treatment only where attached concrete platform and porches are on fill or ground.
<br />U
<br />0 `c
<br />0 -4 S
<br />UU
<br />U
<br />`�y
<br />U
<br />•V-4 o
<br />W " U
<br />-�1 4S 8
<br />V Q-1 "q
<br />0
<br />o�
<br />0
<br />0
<br />;�
<br />_U_
<br />oC9
<br />ZCN
<br />w 04
<br />N�
<br />U
<br />..
<br />-,
<br />..
<br />:.
<br />.�
<br />F
<br />Cl)
<br />O
<br />CZ
<br />U
<br />�__
<br />U
<br />Q
<br />ed
<br />I- [.,,
<br />U
<br />a
<br />•►
<br />cn
<br />z
<br />t
<br />>O)
<br />J
<br />�
<br />i
<br />�
<br />m a, '.
<br />d f '.
<br />* <
<br />I;c
<br />,z
<br />>
<br />z
<br />______.__,__
<br />2
<br />cc
<br />w
<br />a
<br />N
<br />w C�
<br />2R
<br />I I
<br />�
<br />N Ch c0 1� aD .
<br />i_
<br />W R m
<br />U �'I o� m �
<br />w
<br />W M . ¢ Y m
<br />J V
<br />N N 11 C3 = .
<br />d N 0 U
<br />TENANT BUILD OUT
<br />A001
<br />
|