Laserfiche WebLink
ELECTRICAL SPECIFICATIONS <br />Common Electrical Abbreviations <br />ERIC J. SAFFRAN <br />ARCHITECT <br />GENERAL <br />Before submitting a bid, the Contractor shall visit the site and familiarize himself <br />with the existing conditions. The Contractor shall make such ac justments m work as <br />required by the actual conditions and inform the Engineer ofRecord of any discrepancies <br />between achral conditions and design documents. <br />Coordination, Conflict and Changes: The Contractor shall coordinate his work with <br />other trades, particularly in common areas such as mechanical moms, and chases where <br />multiple trades will be working. In the event ofa coo ic; the Architect shall decide which <br />equipment shall be relocated regardless of which was installed first: g during this <br />coordination, it is discovered that necessary or desirable changes should be made, advise <br />the Engineer and secure his approval in writing. Where- drawings appear to cou ict, <br />provide the more expensive quality or quantity. <br />The Contractor shall base his proposal on the materials specified herein and in the <br />drawings. Reference to a particularptvduct by Manuficturw, trade name, or catalog <br />number establishes the minimum standard ofmaterial and equipment required for this <br />installation. It is not intended to exclude products of similar• design and equal quality. <br />Where two or more standards are listed, the choice shall be by the Contractor. The <br />Engineer reserves the sole right to decide the equality ofmateriais proposed for use in lieu <br />of those specified: Permission to substitute shall be obtained prior to bid in accordance <br />with the Architect's instructions. <br />Warkk under this item of the Contract shall include providing all labor, material, <br />equipment; supplies, and services necessary to install a complete and operational electrical <br />system, both nitaw and exterior, as shown in these plans. <br />All material shall be UL listed as approved and shall be new <br />The Contractor shall comply with applicable local htws, the latest edition of the NEC <br />where not in conflict with those laws, and the rules of the local utility company, Americans <br />with Disabilities (ADA) Act, latest edition of the building code adopted by the Authority <br />Having Jurisdiction over this work, NEMA standards, UL standards, ANSI standards, and <br />the Manufacturer's recommendations regarding their product. <br />The Contractor shall obtain and pay for all required permits. The Contractor shall <br />pay all fees associated with the scope of work as outlined in these documrews. Auer <br />completion of the work, the Contractor shall submit certificate of final inspection and <br />approval from the local electrical inspector certifying that the installation complies with all <br />applicable regulations governing same. <br />The Contractor shall warrant the entire electrical system to be in proper working <br />order Replace at no additional charge all work and/or material which may develop defects, <br />excluding ordinary wear and tear and improper handling, for a period of one year from the <br />date ofaccepmace. <br />RACEWAYS <br />Galvanized Rigid Conduit shall be hot -doped galvanized steel inside and outside <br />including threaded cells. Where field cut and threaded, exposed surface shall be treated <br />with a galvaniziaglaint. Conduit shall be manuAwtmed by Allied Tube, Wheatland, <br />Pittsburgh Staorlarrd, Republic, or Triangle. <br />Galvanized Rigid Coated Conduit shall be coated inside and outside with PVC coating <br />and be ETL listed. <br />Intermediiste Metal Conduit shall be hot galvanized steel with a corrosion resistant <br />coating. Where field cut and breaded, exposed surface shall be treated with a galvanizing <br />paint Conduit shall be manufactured by Allied Tube, Wheatland, Pittsburgh Steel, Republic, <br />or Triangle. No Quick connect couplings are allowed <br />Electrical Metallic Tubing shall be hot galvanized steel with a corrosion resistant <br />coating. Conduit shall be msnufactu rd by Allied Tube, Wbestlam4 Pittsburgh Steel <br />Republic, or Triangle. Fittings shall be set screw type fittings. No quick connect <br />compression figs are allowed <br />Rigid non metallic conduit (PVC) shall be heavy wall schedule 40 polyvinyl chloride <br />as manufachred by Carlos. Condectm and fittings shall be by the same manufacturer: <br />Liquid-tigbt ffe:nble metal conduct shall be type UA with writable fittings as <br />manufactued by Anaconda. <br />Flexible metal conduit shall be used for final connection to vibrating machinery and <br />finer junction box to ligh fixture. Run shall be as short as possible but no more than 72 ". <br />Flexible metal conduit shall be as manufactured by AFC. <br />Conduits shall be sized not smaller than as shown or in accordance with Table 1, <br />Chapter 9 of the NEC, whichever is larger: <br />Conduits shall be supported and substantially fastened to structural members at <br />intervals of no more than 8 fret Supports and fasteners shall be of a type approved for the <br />intended use and appropriate for the application Conduit shall be run concealed in the <br />structue as mucb as practicable. When conduit must be exposed, the conduit shall be <br />instilled with rums atfierparallel orperpendicular to structural members, walls, or vertical <br />intersections. Right angles shall consist of cast metal fittings or symmetrical beads. Co ndurt <br />shall be kept a minimum of 6" away from flues, hot water pipes, steam pipes, or other heat <br />producing devices. Conduit which has been pushed or deformed due to improper bending or <br />nushandim shall not be installed Conduit shall be pit square, threaded, reamed smooth, <br />and drawn up 40L Conduit shall be securely ftstened to all abeet metal outlets, cabinets, <br />junction and pull boxes with locknuts and bushings. Provide bushings at each end of the <br />run. Where spare runs of conduit are mi icated, provide a pull wire in each raceway and cap <br />each end to prevent the collection of debris. Conduit systems shall be installed complete <br />prior to pulling conductors. Conduit shall be installed as follows: <br />Underground - PVC with GRC sweep bends for the vertical turns <br />Exposed Exterior -GRC, IMC <br />Exposed Interior - GRC, )MC, EMT (only above 10' AFF ) <br />Concealed Interior - GRC, IMC, EMT, MC/AC Cable ( only if acceptable to <br />heAHJ) <br />No ENT ( "Sunuf tube') allowed. <br />WIRE AND CABLE <br />Conductors shall be soli drawn copper conforming to ASTM standards runless <br />Ahmunum a specifically indicated on the plans. The maaufscture's name, wire size, and <br />insulation type shall be permanently marked on the conductor jacket at regular intervals in a <br />legible manner. All conductors; shall be labeled at each termination and in all junction boxes <br />with cable tags. Conductors shall be as follows: <br /># 12 AWG - #10 AWG TTHIN or THHW Stranded or solid <br />#8 AWG TRW or TTHIW Stranded <br />#6AWG and huger THW, THHW orXHHHW Stranded <br />Riser General Notes: <br />Conductors shall be color coded as follows: <br />12012401Ph 1201209 or 1201240 3 Ph <br />2771480 3 Ph <br />Phase A <br />Black Black <br />Yellow <br />Phase B <br />Blue Blue <br />Orange <br />Phase C <br />N/A Red <br />Brawn <br />Neutral <br />White White <br />White or Grey <br />Ground <br />Green Green <br />Green <br />Any "High Leg" Phase Shall Be Marked with Orange Tape. <br />Wire and cable shall be as manufactured by Southwire, PWC, Carol, Triangle, Anaconda <br />Splices shall be made only in approved locations as follows: #12 AWG - wirenuts <br />#10AWG and larger - compression or camp type slices with insulating hest shrink <br />gym& <br />Fixture wires shall be SF-1 or SF-2 600V minimum #14A WG. <br />AC and MC cables are acceptable where approved by the Authority Having <br />Jurisdiction. <br />BOXES <br />Outlet boxes used in concealed work shall be galvanized or sheradized sheet steel <br />boxes and be adequately sized to accommodate the devices and conductors to be installed <br />(minion 1-112" deep ). Boxes dr tbeirplaster rings shallbe mounted Bush with the <br />finished surface and square with the surfnee. Boxes shall be sized in accordance with <br />NEC Article 314 and be appropriate for the environment in which installed Ceiling <br />boxes shall be 4" octagonal boxes 1-1)2" deep minimum Boxes intended fen mounting <br />ceiling fans shall be rated a minimum of 1001bs weight capacity. Boxes shallbe as <br />manufacdnad by Appleton, Raco, or Steel City. <br />Exposed outlet boxes shall be Crouse -Hinds 7jjw FS or FD or equal. <br />Sectional type boxes shall not be installed in masonry or concrete walls. <br />L,71 1Z ► � <br />Devices shall be as indicated in the Electrical Legend and as shown on the plans. <br />Devices manufwan d by Arnow -Hart, Bryan; or Hubbell and listed in NEMA <br />comparative lists as similar type and quality are approved Finish for devices and cover <br />plates shall be as specified by the Architect. <br />The plans slow apprroximate locations for devices only. The Cwhaictor shall <br />familiarize himself with arrhitoctral and structural details and the rough -in requirements <br />of the equipment to be installed to determine the device location. Devices shall be <br />installed at umifurm heights throughout the installation. Devices installed above <br />countertops shall be installed to avoid eouffict with the backsphusk cabinets, and/or <br />equipment. The final location of devices shall be verified by the Architect. <br />Pull boxes shall be installed in long runs of conduit: Pull boxes shall be <br />galvanized sheet steel construction, sized aeeordilag to NEC Article 314, and installed in <br />an aoecssible location. <br />SAFETY SWITCI w <br />Disconnect sanity switches shall be heavy dirty type 600V or 250V , fused or <br />non -fused as indicated on the plans with the number ofpoles as indicated on the plans. <br />NEMA enclosure type shall be as indicated on the pleas Switch mechanism shall b <br />"quick make - quick break" type ooasbnrcbion <br />The Contactx shall provide mounting frames for switches that can not be securely <br />fastened to a solid structure. Frames shall consist ofgalvanized stool chi are/ set in <br />concrete footings. Hardware (ours, bolts, washers, etc) shall be stainless steel. <br />Switches installed as service entrance disconnects shall be labeled as such and be <br />provided with all accessories and appurtenances required for a service entrance disconnect <br />SERVICE <br />Coordinate with Utility to provide a service as indicated on the plans. Provide all <br />material and labor not supplied by the Utility in order to produce a complete to and operable <br />electrical service complying with NEC and Utility Company regulations. <br />Obtain metering equipment from Utility and install in compliance with Utility <br />Companyregullstiorts. <br />Unless Noted Otherwise, the transformer at the Service Entance will be provided <br />by the Utility. <br />GROUNDING <br />The Contractor shall provide complete system and equipment pumidrng systems <br />Iudbig coadhuctom o�Mm Brood rods, pound buusses, ink all etcfor the service <br />entrance ground, groumcting ofelech ical equipme4 process egiq= n; building steel, or <br />other itms indicated on the drawings. The grounding system shall be installed in <br />accordance with NEC Article 250 and as detailed in the plans. <br />Undiergnoumd connections and connections to building steel shall be exothermic <br />weld. Exposed concoctions shall be irreversible crimp type connections. <br />A green insulated ground conductor as indicated on the plans (nzimimurn size per <br />NEC Table 250.122 ) shall be metalled in each raceway and with each cable.Isolated <br />Ground conductors shall be green with yellow dace. <br />DRY TYPE TRANSFORMERS <br />Transformers of the size and type covered in UL 506 shall be so listed and labeled, <br />ie. Transformers 600V up to and inchding 167 kVA single phase and 500 kVA three <br />phase. Three phase transformers up to 9 kVA shall be Class 180 Insulation System with <br />80 C Rise. Single Phase transformers and three phase transformers 15 kVA to 500 kVA <br />shall be Class 220 kwiston System with 115 C rise. Cores shall be designed so dot <br />maximum fiuur demsitim are substantially below saturation level. The core volume shall <br />allow efficient operation at 109/9 above the highest tap voltage. All laminators shall be <br />come pasted or annealed, fire of buns and firmly butted The core laminations must be <br />tightly clamped and compressed to provide quiet operation. The entire core and coil <br />assembly must be pedried by hen; napregnsted with silicome varnish, and cured at a <br />minimum of350 F to reduce hotspots and seal out moisture. Coils must be protected with <br />an outer layer ofg1m tape or similar insulation. Transformers 15kVA and larger shall <br />have NEMA standard taps. All tandbimers shall be quiet type. Care and coil assemblies <br />are to be mounted an rubber vibration isolators designed to specifically reduce 120 He <br />sound and multiple harmonics. Enclosure temperature rise shall not exceed 40 C rise <br />above ambient Windings shall be copper Transformers shall be miuuftcdmod by Square <br />1) A fault current ofLsc-45,242A was obtained from the u duty. <br />IT size or fault current is differen4 notify Architect immediately for resolution <br />2) Notify Architect Immediately to obtain a resolution ifany discrepancy between field condlitidmns and conduction documents that impacts installation is discovered. <br />3) Seal Penetrations to Insmre Integrity ofBudding Envelope. Coordinate with Architect <br />NOTICE TO CONTRACTORS: <br />ALL CONTRACTORS PRIOR TO BID SUBMISSION PROCESS SHALL VISIT <br />PROPOSED WORK SITE AND FIELD VERIFY ALL EXISTING CONDITIONS. <br />ANY CONDITIONS THAT DIFFER FROM THAT SHOWN ON THESE PLANS <br />SHALL BE REPORTED TO ARCHITECT/ENGINEER SO THAT NEW AND <br />REVISED BID DRAWINGS OR INFORMATION MAY BE ISSUED. MODIFICATIONS <br />TO SCOPE OF WORK WHICH RESULTS FROM CONTRACTORS NEGLECT <br />TO VISIT THE SITE PRIOR TO SUBMITTING BID, SHALL BE THE CONTRACTORS <br />SOLE RESPONSIBILITY. <br />E r I <br />MOTORS <br />Motors installed under this section shall be TEFC premium efficiency motors <br />suitable for duty in the environment in which they are installed <br />The Contractor shall verify the correct rotation of all motors in the prvjec; whether <br />installed under this section or another <br />PANHXOARDS <br />Paaelboards shall have the number ofphases and wires as indicated on the <br />panel acbedule. The NEMA enclosure type shall be as noted on the panel schedule. <br />Pandboards shall have copper buss, 100% rated neutral with set screw connections, <br />and grand buss with set screw connection The panel box shall not be less than 20 <br />inches wide and be Abritated from galvanized orgalvannea[ed steel. Boxes shall be <br />constivctad with minimum wire bending and gutter dimensions as required by UL and <br />NEC. Tire Box shall have a separate UL label. All miencis willbe factory <br />assembled and braced fora symmetrical fault current as indicated on the panel <br />schedule C'fmuit breakers shall be replaceable without disdubing adjacent units, and <br />without drifting or tapping. All circuit breakkerconnections shall be m a hole tapped <br />by the manufacturer. Circuit breakers shall have common tie trip handles where <br />required. Field ties are not acceptable. Circuit breakers shall have visible trip <br />indication. PAndboards shall be famished with legible, typed panel directories <br />acemaidy identifying the load each circuit breaker saver. Panelboards shall be as <br />manufactured by Square D, Siemens, GE, or Cuder Hammer <br />LIGHT FIXTURES <br />Furnish and install fixduts as indicatod in the Light Fixture Schedule. Catalog <br />numbers indicate base unit: 77w Contra shall fumish all escutcheon plates, p!asw <br />rings, and plates, hanging chains, stems, and other appurtenances necessary for a <br />cOmpklae installation. The Contractor shall match the voltage of the fixture to the <br />voltage of the desigaatod circuit <br />The Engineer reserves the sole right to determine the quality of any fixture <br />proposed for use in lieu of those specified <br />]matures shall be supported from structure Where installed in lay in acoustic <br />tile ceiling, fixtures shall be supported from structure by two diametrically opposed <br />cornerx <br />Lamps shall be as manukwhu ed by Sylvania, Phillips, or GE. <br />Fluorescent lamps shall be cool whit; unless noted otherwise. <br />Fluorescent ballast shall be high efficiency, low temperature electronic ballasts with <br />less than 10% T HD unless noted otherwise. Ballasts shall be manufactured by Sylvania, <br />Advaoae, or GE. Emergency ballasts shall be manufactured by Bodine. <br />Match the fixture tin to the surface nVon which the fixture is installed <br />Recessed fixtures shall be IC noted fixtures unless noted otherwise Recessed <br />fixtures installed in fire rated assemblies shall be provided with a UL listed method of <br />instillidom to maintain the foe rating of the assembly as designated in the Architectural <br />Plans. <br />Recessed f xtums installed in the building envelope shall be provided with an <br />approved method of installation toprevent air migration through the opening or fixture m <br />accordance with the latest version of the Energy Code. <br />LABELLING <br />Provide engraved phenolic labels white 112" high letters on black background for <br />each pnoelboard>, loadexmter, disconnect switch, service main, etcto identify the <br />equipment served by the device or equipment <br />FIRE RATED SEALS <br />Provide a UL approved fine seal for each and everypenetration of a fire rated <br />assembly ( wal), ceiling; and/or Door) in order to maintain the fire rating of the assembly <br />as indicated in the AmIth ectural plans. Do not install devices within 6" of each other <br />back to back in any fire rated assembly. <br />TELEPHONE <br />Contractor shall coordinate with local utility for exact telephone service <br />roquirameats. The Contractor shall provide a Telephhone Termination Cabin; sized as <br />indicated on the plans, for mounting telephone equipment Provide a #6 A WG ground <br />fain the backboard to the main service ground. Leave s minimmn 6ofslack at the <br />board for termination. <br />CATV <br />Contra shall coordinate with local utility for exact cable television service <br />requirements. The Czatrntor shall provide an AC grade plywood backboard, sized as <br />indicated on the plans, treated with fine retardant paint fur mounting cable television <br />equipment Provide a #6 AWG ground firm the backboard to the main service ground. <br />Leave a minimum 6' of slack at the board for termination <br />A, Amp <br />Amperes <br />EQ <br />Equal, Equipment <br />SBC <br />Standard Building Code <br />AC <br />Alternating Curren; Armored Cable <br />EQUIP <br />Equipment <br />SH <br />Sheet <br />ACT <br />Above Counter Top <br />EX <br />Existing <br />SW <br />switch <br />ADA <br />American's with Disabilities Act <br />FA <br />Fire Alarm <br />TEL <br />Telephone <br />AF <br />Amp Fuse <br />FAAP <br />Fine Alarm Annuciatvr Panel <br />UG <br />Undwgroumd <br />AFF <br />Above Finished Floor <br />FRCP <br />Fine Alarm Cembrol Pawl <br />UL <br />Underwriters Laboratory <br />AFG <br />Above Finished Grade <br />FIX <br />Fixture <br />UNO <br />Unless Noted Otherwise <br />AHU <br />Air Handling Unit <br />FL <br />Floor <br />V <br />Volt <br />AFC[ <br />Arc Fault Circuit Inie7rupter <br />FU <br />Fused <br />W <br />Wire <br />Al <br />Aluminum <br />GFCI <br />Ground Fault Circuit Interrupter <br />WP <br />Weatherproof <br />ANSI <br />American National Standards Institute <br />GFI <br />Ground Fault (Circuit] Inoetrupter <br />)0;11M <br />Transformer <br />Approx <br />Approximately <br />GRC <br />Galvanized Rigid Steel Conduit <br />Arch <br />Architect <br />HP <br />Horsepower, House Panel <br />ASHRAE <br />American Society ofHeating, Refrigeration and Air -Conditioning Engineers <br />HZ <br />Hertz <br />AWG <br />American Wire Gauge <br />IAW <br />In Accordance With <br />BD <br />Board <br />IBC <br />Intemadacal Building Code <br />BLDG <br />Building <br />IEEE <br />Institute of Electrical and Mecironies Engineers <br />C <br />Condui; Centigrade, Celsius <br />IMC <br />Intermediate Metallic Conduit <br />C&P <br />Corp dt Plug <br />ISA <br />Instrument Society ofAmerica <br />C/L <br />Cemteriine <br />JB <br />Junction Box <br />CAB <br />Cabinet <br />KAIC <br />Kilo-Ampew Iotemnrpting Capacity <br />CAP <br />Capacity <br />KVA <br />Kilo Volt Ampere <br />CB <br />Circuit Breaker <br />KVAR <br />Kilo Volt -Ampere Reactive <br />CKT <br />Circuit <br />KW <br />Kilo Watt <br />CLG <br />Ceiling <br />KWH <br />Kilo Wan Hour <br />COL <br />Colulmn <br />MC <br />Metallic Cable <br />Cond <br />Conduit <br />MCB <br />Main Circuit Breaker <br />CONN <br />Connection <br />MECH <br />Mechanical <br />CONT <br />Continua, Continuation <br />MISC <br />Miscellaneous <br />CPT <br />Control Power Transformer <br />Mw <br />Man Lug Only <br />CT <br />Current Transformer <br />AM <br />Motor Rated Switch <br />Cu <br />Copper <br />MT O <br />Mounted <br />DIC <br />Disconnect Switch <br />MTR <br />Mom <br />DET <br />Detail <br />NC <br />Nn maily Closed <br />DF <br />Drinking Fountain <br />NEC <br />National Electric Code <br />DN <br />Down <br />NEMA <br />National Electrical Mmufacdrar's Association <br />DWG <br />Drawing <br />NF <br />Nam -Fused <br />EA <br />Each <br />NFPA <br />National Fire Protection Association <br />EC <br />Empty Conduit; Electrical Contractor <br />NMC <br />NonMetallic Cable, NonMegsllic Conduit <br />EDF <br />Electric Drinking Fountain <br />NO <br />Number, Normally Open <br />EF <br />Exhaust Fan <br />NTS <br />Not To Scale <br />ELEC <br />Electric, Electrical <br />OH <br />Overhead <br />EMT <br />ElectroMetallic Conduit <br />Ph <br />Phase <br />PNL <br />Panel <br />PVC <br />PolyVi TKWaride Conduit <br />RTU <br />Roof Top Uri; Radio Telemetry Unit <br />Riser Diagram Keyed Notes: <br />01 Existing Wkmmy to Remain ( 8WA ). Field Verify. <br />© Existing Ground To Remain. <br />® Existing House Panel Discomnect To Remain. <br />Existing Tenant Disconnect To Remain. <br />Currently Vacant <br />© jaxisimir 200A Conductors and Conduit to Remain Field Vey <br />Instan t) ##2IG Continuous to Isolated Ground Buss in Pawl LB. <br />43 g 200A Safety Disconnect for Tenant Use. <br />Field Verify Fuses Are Class J and 200A. <br />© Existing 200A Conductors and Conduit to Remain. Field Verify. <br />® Panel LA. <br />0 (4) #6, (1) #10G, (1) #2IG, 1 "C. <br />® Panel LB <br />Install (1) #2 IG Continuous firm Main Service Ground to <br />Isolated Ground Buss in Panel. <br />® Panel LA2. <br />© Lighting Contactor for Exterior Sign(s)/ Lights. <br />30A EOEff 4 Pole Coniacton(s) in NEMA 1 Enclosure. <br />Square D Class 8903 Type S or Equal. <br />Tirawlock for Control of Exterior Sign(s). <br />Seven Day Skip A Day Astronomic wi Battery Backup, Taxf or <br />Equal. <br />® Provide Permanently Affixed Label <br />"Five Guys Disconnect 112" <br />® Provide Pemiatiently Affixed Label <br />"Five Guys Disconnect Z2" <br />® Provide Permanently Affixed Label <br />'Fed From Five Guys Disconnect 112" <br />© Provide Permanently Affixed Label <br />"Fed From Five Guys Disconnect 212" <br />PROJECT GENERAL NOTES: <br />1. Routing sbown a diagrammatic ably. Field verify exact routing of oarduit and coadutcbors. <br />2. Contractor shall verify do" swings prior to installing light switches. <br />3. Lay m light fixtures shall be shad on opposite corners from stuct m. <br />4. No oombuatble material shall be installed m a plenum sp wo Verify Plcenm Spaces with Architectural and Mechanical. <br />5. Cover plates shall be installed fax• all dmces. Where merle than one device is indicated is the same location, the devices shall be ganged <br />under a common plate <br />6. No devices shall be mounted within 24" of another device on opposite sides ofa fine rated wall. <br />7. The Branch Circuit feeding the emergency ligliftWexit signs shall be the saw as that serving the normal lighting to the am and connected <br />ahead of any local switches <br />8. All wire shall be Capper. <br />9. Any flexible coodult shall NOT exceed 5'-0" in hngth. <br />10. Coordinate Mounting Heights for Kitchen Equipment with Kitchen Equipment Supplier, Architectural Plans, and General Contractor Prior to <br />Rougb-In. <br />11. Device Cove.rph tes Shall Be Stainless Steel. All Devices Shari Be WHITE in Color. Provide Blank Coveiplates Where Devices Are Not <br />Installed <br />12. All Devices New UNO. <br />EX - Existing to Remain <br />EX R - Existing Shown in Relocated Position. <br />13. Information contained in these plans regarding existing equipment was supplied by a third party. The Contrator shall field verify exact <br />requirements of the existing equipment. Where that are discrepancies between the design documents and the actual installatiom, the Contractor <br />shall inform the Architect immediately for a resolution. <br />James E. Tremel ling, PE <br />4838 Campground Road <br />Alexander City, Alabama 35010 <br />r (250 329-3557 F/aidr PEW. Pmjact P <br />P: (2-%) 329-3" 58973 2010022 <br />Preston Ridge Commons <br />3155 North Point Parkway <br />Building E - Suite 200 <br />Alpharetta, Georgia 30005 <br />Tel 770 619 5916 <br />Fax 770 619 5919 <br />``�elalulrr) <br />��g�' T•REMcc��'. <br />r <br />-� 0 G)51 cc <br />- <br />- <br />.4 .4 <br />li <br />H <br />Z <br />W <br />M <br />LU <br />ZQQ <br />aC <br />"LL I <br />:D-0 <br />LL <br />O J DC <br />==O <br />O0 tv <br />H O _5 <br />Hm Li- <br />L <br />z <br />Q Q J <br />WV— <br />a <br />Joe <br />1:� o=C <br />00 <br />��_ <br />^LU <br />@M100011 <br />m <br />ac W <br />N <br />uWLU <br />3: <br />N <br />REVISIONS <br />NO. <br />DATE <br />REVISION <br />IfQX3MNtFlCATM CLAUSE <br />THE OWNER SHALL RELEASE, HOLD <br />HARMLESS, AND INDEMNIFY THE <br />ARCHITECT WITH RESPECT TO: ANY <br />CHANGES MADE TO THE CONSTRUCTION <br />DOCUMENTS BY ANYONE OTHER THAN <br />THE ARCHITECT, OR CHANGES IN ANY <br />ASPECT OF THE WORK OR FAILURE BY <br />THE CONTRACTOR TO BUILD IN <br />ACCORDANCE WITH THESE <br />CONSTRUCTION DOCUMENTS <br />ERIC 11. SAFFRAW <br />AifCHITKT <br />THIS DRAWING IS THE PROPERTY OF <br />ERIC 1. SAFFRANI ARCHITECT <br />AND IS NOT To BE REPRODUCED OR <br />COPIED IN WHOLE OR IN PART. <br />UNAUTHORIZED USE OF ANY KIND, <br />INCLUDING USE ON ANY OTHER <br />WPR ECT ISPROHIBITED. IT IS TO BE <br />RNED UPON REQUEST. <br />L <br />SPECIFICATIONS & <br />RISER DIAGRAM <br />SCALE <br />