|
DocuSign Envelope ID. 36F18693-F185-48FC-BA20-05B28AEDBD00
<br />ELECTRICAL RISER DIAGRAM
<br />OPTIONAL OVERHEAD
<br />SERVICE SAME AS
<br />UNDERGROUND 150 OR 200
<br />AMP SERVICE
<br />METER MAIN
<br />DISC.
<br />150 OR
<br />- - — 200 AMP
<br />UNDGND
<br />SERV.BY
<br />POWER CO.
<br />Footer-- J , I
<br />y '
<br />Re -Bar (sized
<br />according to
<br />foundation plan)
<br />a
<br />#4 awg CU bare w/ 10' stubbed
<br />outside of slab at service o
<br />location. Connect to footer steel LO
<br />w/ (2) ground clamps 5' apart
<br />a d
<br />UFER GROUND DETAIL
<br />N.T.S.
<br />150 = #1 Copper or 2/ 0 Aluminum
<br />200 = 2 /0 Copper or 4 /0 Aluminum in 2"
<br />Conduit. A/C DISCONNECT
<br />#12 COPPER TO APPLIANCES AND GFI
<br />TYPICAL
<br />ELECTRICAL -- #14 COPPER TO LIGHTS AND OUTLETS
<br />PANEL _-_- #10 COPPER TO WATER HEATER
<br />#8 COPPER TO RANGE
<br />-- #6 COPPER TO HVAC
<br />N.T.S. #4 GROUNDING WIRE WITH CODE APPROVED CLAMP TO EITHER:
<br />1 A) APPROVED GROUNDING ROD WITH MINIMUM 8' DEPTH
<br />B) BONDED TO CONTINUOUS FOOTING STEEL
<br />- INTERSYSTEM BONDING TERMINATION PER NEC 250.94
<br />NOTE:
<br />ELECTRICAL MATERIAL AND INSTALLATIONS SHALL COMPLY WITH APPLICABLE
<br />PROVISIONS OF THE NFPA 70, LOCAL CODES AND LOCAL POWER/UTILITY COMPANY
<br />GENERAL ELECTRICAL NOTES
<br />ALL ELECTRICAL DESIGN AND WORK SHALL BE IN STRICT
<br />COMPLIANCE WITH THE 2017 NATIONAL ELECTRIC CODE
<br />• PER NEC SECTION 210.12 (B) ALL 15A & 20A, 120V
<br />BRANCH CIRCUITS SUPPLYING OUTLETS REQUIRE
<br />AFCI PROTECTION
<br />• CARBON MONOXIDE PROTECTION PER FLORIDA
<br />STATUTES 553.885 (2). TO BE INSTALLED WITHIN 10'
<br />OF EVERY SLEEPING ROOM
<br />• ALL OUTLETS SHOULD BE AFCI PER NEC - U.N.O.
<br />• PER NEC SECTION 210.8(B)(5) ALL 15A & 20A, 15V
<br />RECEPTACLES INSTALLED OUTDOORS MUST BE
<br />GFCI-PROTECTED
<br />• PER NEC SECTION 210.8(B)(5) ALL 15A & 20A, 15V
<br />RECEPTACLES INSTALLED WITHIN 6' OF SINK (IN
<br />NON -DWELLING OCCUPANCIES-i.e. OUTDOOR
<br />SUMMER KITCHENS RECEPTACLES) MUST BE
<br />GFCI-PROTECTED
<br />• PER NEC SECTION 406.8(B)(1) 15A & 20A
<br />RECEPTACLES IN A WET LOCATION MUST BE WITHIN
<br />AN ENCLOSURE THAT IS WEATHERPROOF WHEN AN
<br />ATTACHMENT IS PLUGGED IN AN ALL NON -LOCKING
<br />RECEPTACLES SHALL BE LISTED AS WEATHER
<br />RESISTANT
<br />• PER NEC SECTION 406.11 IN DWELLING UNITS, ALL
<br />15A & 20A, 15V RECEPTACLES SHALL BE LISTED AS
<br />TAMPER -RESISTANT
<br />• PER NEC SECTION 800.156 NO LESS THAN ONE
<br />COMMUNICATION OUTLET SHALL BE INSTALLED
<br />WITHIN EACH DWELLING UNIT
<br />• PER NEC SECTION R314.3 AND R315.1 SMOKE
<br />DETECTORS TO BE INSTALLED INSIDE EACH
<br />SLEEPING AREA
<br />• ALL SMOKE ALARMS SHALL BE LISTED AND LABELED
<br />IN ACCORDANCE WITH UL 217, PER FBC 314.1. GC TO
<br />INSTALL; KIDDE MODEL # 14618A SMOKE ALARM, OR
<br />APPROVED EQUAL
<br />• PROVIDE GAS DROPS AS PER COMMUNITY ONLY
<br />• JUNCTION BOX AT WATER HEATER, RANGE AND/OR
<br />DRYER TO BE 220V IN NON GAS COMMUNITIES, AND
<br />110V IN COMMUNITIES THAT HAVE GAS OPTIONS
<br />PROVIDE APPROPRIATE RECEPTACLE PER
<br />APPLIANCE
<br />• ALL LAMPS SHALL BE HIGH -EFFICACY TO COMPLY
<br />WITH FBC-EC R404.1 - (LOW -VOLTAGE LAMPS
<br />EXCLUDED).
<br />• PER FBC-R M1305.1 A LEVEL WORKING SPACE NOT
<br />LESS THAN 30" DEEP AND 30" WIDE SHALL BE
<br />PROVIDED IN FRONT OF THE CONTROL SIDE OF ANY
<br />APPLIANCE
<br />ABBREVIATIONS LEGEND
<br />ABV
<br />ABOVE
<br />AC
<br />AIR CONDITIONER
<br />AFF
<br />ABOVE FINISHED FLOOR
<br />AHU
<br />AIR HANDLER UNIT
<br />BLK
<br />BLOCK
<br />CABS
<br />CABINETS
<br />CLG
<br />CEILING
<br />CHR
<br />CHAIR RAIL
<br />COFF
<br />COFFERED
<br />COL
<br />COLUMN
<br />COND
<br />CONDENSER
<br />CRN
<br />CROWN MOULDING
<br />CVAC
<br />CENTRAL VACUUM SYSTEM
<br />DBL
<br />DOUBLE
<br />DIAG
<br />DIAGONAL
<br />DR
<br />DOOR
<br />DRY
<br />DRYER
<br />DW
<br />DISHWASHER
<br />EB
<br />EYEBROW
<br />FL
<br />FLOOR LINE (MAT. CHANGE)
<br />FLR
<br />FLOOR
<br />FP
<br />FIREPLACE
<br />FXD
<br />FIXED
<br />FXT
<br />FIXTURE
<br />GLS
<br />GLASS
<br />HB
<br />HOSE BIB
<br />KS
<br />KNEE SPACE
<br />LAV
<br />LAVATORY
<br />LT
<br />LAUNDRY TUB
<br />MRBL
<br />MARBLE
<br />MC
<br />MEDICINE CABINET
<br />MIR
<br />MIRROR
<br />MTL
<br />METAL
<br />OH
<br />OVERHEAD
<br />OPNG
<br />OPENING
<br />OPT
<br />OPTIONAL
<br />R & S
<br />CLOTHES ROD and SHELF
<br />REF
<br />REFRIGERATOR
<br />SD
<br />SOAP DISH
<br />SDLTS
<br />SIDE LIGHTS
<br />SGD
<br />SLIDING GLASS DOOR
<br />SH (2)
<br />SHELVES (QUANTITY)
<br />SHWR
<br />SHOWER
<br />TB
<br />TOWEL BAR
<br />TPH
<br />TOILET PAPER HOLDER
<br />T&S
<br />TUB and SHOWER
<br />TEMP
<br />TEMPERED
<br />TR
<br />TRANSOM
<br />VOL
<br />VOLUME
<br />WC
<br />WATER CLOSET
<br />WD
<br />WOOD
<br />WH
<br />WATER HEATER
<br />WNCT
<br />WAINSCOT
<br />WS
<br />WATER SOFTENER
<br />WASH
<br />WASHER
<br />ROOF NOTES
<br />• INSTALL ROOF VENTING PER MFR WRITTEN
<br />INSTRUCTIONS PER FBC R806
<br />• ALL OVERHANG DIMENSIONS ARE TO EDGE OF
<br />RAFTER. REFERENCE WALL SECTIONS/DETAILS
<br />FOR ALL OVERHANGS NOT DIMENSIONED.
<br />• ALL UNDERLAYMENT MUST BE INSTALLED IN
<br />COMPLIANCE WITH FBC R905.1.1
<br />• EACH 4' OFF RIDGE VENT REQUIRES (1) 46" x 3" CUT
<br />OUT IN ROOF SHEATHING PER MFR WRITTEN
<br />INSTRUCTIONS
<br />ROOF VENT CALCULATION
<br />FORMULA:
<br />1 SQUARE INCH VENT FOR EVERY 300 SQUARE INCHES
<br />OF CEILING
<br />*144 SQ. IN. = 1 SQ. FT.
<br />BLDG. CEILING (SF) x 144 = BLDG (SQ. IN.)
<br />BLDG. (SO. IN.) 1300 = SQ. IN. OF VENT REQUIRED
<br />SQ. IN. OF VENT REQUIRED / 2 = 50% AT HIGH AND 50%
<br />AT LOW.
<br />PER FBC SECTION R806.2: 40% MIN, BUT NOT MORE
<br />THAN 50% OF VENTILATION MUST BE PROVIDED BY
<br />VENTILATORS LOCATED NO MORE THAN 3'-0" BELOW
<br />THE RIDGE OR HIGHEST POINT OF THE SPACE
<br />BASIS OF CALCULATION: ("OR EQUAL" ACCEPTABLE)
<br />(a) OFF RIDGE VENTS - STAMPCO W/ 36 SQ IN (NFVA)
<br />PER LINEAL FT
<br />(b) SOFFIT VENTS - GP T3-1/3" FULL VENT PERFORATED
<br />W/ 9.19 SQ IN (NFVA) PER LINEAL FT
<br />CALCULATED LINEAL FOOT OF SOFFIT VENT SHALL
<br />NOT INCLUDE NON -VENTED FIRE RATED SOFFIT
<br />LOCATED LESS THAN 5' FROM PROPERTY LINE
<br />EXTERIOR ELEVATION GENERAL NOTES
<br />• FRONT ELEVATIONS BANDING, MOLDING,
<br />COLUMNS AND TRIM SHALL RECEIVE A SAND
<br />FINISH. SEE ELEVATION FOR DEPTH OR RAISED
<br />BANDING
<br />• SIDE AND REAR ELEVATIONS BANDING AROUND
<br />WINDOWS AND DOORS MAY BE OPTIONAL PER
<br />COMMUNITY SPECS - SEE COMMUNITY
<br />SPECIFICATIONS OR CONSULT THE
<br />CONSTRUCTION MANAGER. ALL BANDING SHALL
<br />RECEIVE A SAND FINISH
<br />• ROOF COVERING SEE COMMUNITY
<br />SPECIFICATIONS OR CONSULT THE
<br />CONSTRUCTION MANAGER. SEE STRUCTURAL
<br />SHEETS FOR SHEATHING REQUIREMENTS
<br />• FLASHING SHALL BE INSTALLED AT WALL AND
<br />ROOF INTERSECTIONS, DECK AND WALL
<br />INTERSECTIONS, AT GUTTERS, AT ALL CHANGES IN
<br />ROOF SLOPE OR DIRECTION, AND AROUND ROOF
<br />OPENINGS
<br />• WINDOW PAN FLASHING SHALL BE IN
<br />ACCORDANCE WITH FBC R703.4
<br />• WALL HEIGHTS VERIFY ALL BEARING WALL
<br />HEIGHTS WITH FINAL TRUSS LAYOUTS
<br />• LATH PER FBC R703.7.1, LATH AND LATH
<br />ATTACHMENTS SHALL BE OF
<br />CORROSION -RESISTANT MATERIALS. EXPANDED
<br />METAL OR WOVEN WIRE LATH SHALL BE
<br />ATTACHED WITH 11/2-INCH-LONG (38 MM), 11 GAGE
<br />NAILS HAVING A 7/16-INCH (11.1 MM) HEAD, OR
<br />7/8-INCHLONG (22.2 MM), 16 GAGE STAPLES,
<br />SPACED NOT MORE THAN 6 INCHES (152 MM), OR
<br />AS OTHERWISE APPROVED
<br />• PLASTER PER R703.7.2, PLASTERING WITH
<br />PORTLAND CEMENT PLASTER SHALL BE NOT LESS
<br />THAN THREE COATS WHERE APPLIED OVER METAL
<br />LATH OR WIRE LATH AND SHALL BE NOT LESS
<br />THAN TWO COATS WHERE APPLIED OVER
<br />MASONRY, CONCRETE, PRESSURE -PRESERVATIVE
<br />TREATED WOOD OR DECAY -RESISTANT WOOD AS
<br />SPECIFIED IN SECTION R317.1 OR GYPSUM
<br />BACKING. IF THE PLASTER SURFACE IS
<br />COMPLETELY COVERED BY VENEER OR OTHER
<br />FACING MATERIAL OR IS COMPLETELY
<br />CONCEALED, PLASTER APPLICATION NEED BE
<br />ONLY TWO COATS, PROVIDED THE TOTAL
<br />THICKNESS IS AS SET FORTH IN TABLE R702.1(1).
<br />ON WOOD -FRAME CONSTRUCTION WITH AN
<br />ON -GRADE FLOOR SLAB SYSTEM, EXTERIOR
<br />PLASTER SHALL BE APPLIED TO COVER, BUT NOT
<br />EXTEND BELOW, LATH, PAPER AND SCREED. THE
<br />PROPORTION OF AGGREGATE TO CEMENTITIOUS
<br />MATERIALS SHALL BE AS SET FORTH IN TABLE
<br />R702.1(3)
<br />• WEEP SCREED PER R703.7.2.1 A MINIMUM
<br />0.019-INCH (0.5 MM) (NO. 26 GALVANIZED SHEET
<br />GAGE), CORROSION -RESISTANT WEEP SCREED OR
<br />PLASTIC WEEP SCREED, WITH A MINIMUM
<br />VERTICAL ATTACHMENT FLANGE OF 31/2 INCHES
<br />(89 MM) SHALL BE PROVIDED AT OR BELOW THE
<br />FOUNDATION PLATE LINE ON EXTERIOR STUD
<br />WALLS IN ACCORDANCE WITH ASTM C926. THE
<br />WEEP SCREED SHALL BE PLACED NOT LESS THAN
<br />4 INCHES (102 MM) ABOVE THE EARTH OR 2 INCHES
<br />(51 MM) ABOVE PAVED AREAS AND SHALL BE OF A
<br />TYPE THAT WILL ALLOW TRAPPED WATER TO
<br />DRAIN TO THE EXTERIOR OF THE BUILDING. THE
<br />WEATHER -RESISTANT BARRIER SHALL LAP THE
<br />ATTACHMENT FLANGE. THE EXTERIOR LATH SHALL
<br />COVER AND TERMINATE ON THE ATTACHMENT
<br />FLANGE OF THE WEEP SCREED
<br />• WATER -RESISTIVE BARRIERS PER R703.7.3,
<br />WATER -RESISTIVE BARRIERS SHALL BE INSTALLED
<br />AS REQUIRED IN SECTION R703.2 AND, WHERE
<br />APPLIED OVER WOOD -BASED SHEATHING, SHALL
<br />INCLUDE A WATER -RESISTIVE VAPOR -PERMEABLE
<br />BARRIER WITH A PERFORMANCE AT LEAST
<br />EQUIVALENT TO TWO LAYERS OF GRADE D PAPER.
<br />THE INDIVIDUAL LAYERS SHALL BE INSTALLED
<br />INDEPENDENTLY SUCH THAT EACH LAYER
<br />PROVIDES A SEPARATE CONTINUOUS PLANE AND
<br />ANY FLASHING (INSTALLED IN ACCORDANCE WITH
<br />SECTION R703.4) INTENDED TO DRAIN TO THE
<br />WATER -RESISTIVE BARRIER IS DIRECTED
<br />BETWEEN THE LAYERS
<br />GENERAL NOTES
<br />• ALL CONSTRUCTION SHALL MEET THE LATEST
<br />EDITION OF CODES ADOPTED BY THE LOCAL
<br />GOVERNING AGENCIES
<br />• PER FBC R302.5 NO OPENINGS FROM A PRIVATE
<br />GARAGE ARE PERMITTED DIRECTLY INTO SLEEPING
<br />AREAS. ALL OPENINGS SHALL HAVE SOLID WOOD,
<br />INSULATED STEEL OR 20 MIN. FIRE RATED DOORS
<br />NOT LESS THAN 1-3/8 INCHES THICKNESS, EQUIPPED
<br />WITH A SELF CLOSING DEVICE. ALL DUCTS IN THE
<br />GARAGE OR PENETRATING THE WALL OR CEILING
<br />SEPARATING THE GARAGE AND DWELLING SHALL BE
<br />CONSTRUCTED OF MIN. 26 GA. SHEET METAL, 1 INCH
<br />MINIMUM RIGID CLASS 0 OR 1 DUCT BOARD, OR
<br />OTHER APPROVED MATERIAL AND SHALL HAVE NO
<br />OPENINGS INTO THE GARAGE
<br />• PER FBC TABLE R-302.6 GARAGE SHALL BE
<br />SEPARATED FROM RESIDENCE AND ITS ATTIC W/
<br />MIN. 1/2" GYP BOARD ATTACHED IN ACCORDANCE
<br />WITH TABLE R702.3.5. HABITABLE ROOMS SHALL BE
<br />SEPARATED FROM ROOM ABOVE W/ MIN 5/8" TYPE
<br />"X" GYP BOARD, WHERE THE SEPARATION IS A
<br />FLOOR -CEILING ASSEMBLY. ANY STRUCTURE
<br />SUPPORTING THE ASSEMBLY SHALL BE PROTECTED
<br />W/ MIN 1/2" GYP BOARD
<br />• PER FBC R309.1 GARAGE AND CARPORT FLOOR
<br />SURFACE AREAS USED FOR PARKING OF
<br />AUTOMOBILES OR OTHER VEHICLES SHALL BE
<br />SLOPED TO FACILITATE THE MOVEMENT OF LIQUIDS
<br />TO A DRAIN OR TOWARDS THE MAIN VEHICLE ENTRY
<br />DOORWAY
<br />• PER FBC R-312.1 PORCHES, BALCONIES OR RAISED
<br />FLOOR SURFACES LOCATED MORE THAN 30" ABOVE
<br />FINISHED FLOOR OR GRADE SHALL HAVE GUARDS
<br />NOT LESS THAN 36" IN HEIGHT. PER FBC R-312.1.2
<br />OPEN SIDES OF STAIRS WITH A TOTAL RISE OF
<br />MORE THAN 30" ABOVE FINISHED FLOOR OR GRADE
<br />SHALL HAVE GUARDS NOT LESS THAN 34" IN HEIGHT
<br />MEASURED VERTICALLY FROM THE NOSING OF THE
<br />TREADS
<br />• PER FBC R-312.1.3 REQUIRED GUARDS ON OPEN
<br />SIDES OF STAIRWAYS, RAISED FLOOR AREAS,
<br />BALCONIES AND PORCHES SHALL HAVE
<br />INTERMEDIATE RAILS OR ORNAMENTAL CLOSURES
<br />WHICH DO NOT ALLOW PASSAGE OF A SPHERE 4"
<br />OR MORE IN DIAMETER
<br />• PER FBC R-308.4.5 GLAZING IN WALLS, ENCLOSURES
<br />OR FENCES CONTAINING OR FACING HOT TUBS,
<br />SPAS, WHIRLPOOLS, SAUNAS, STEAM ROOMS,
<br />BATHTUBS, SHOWERS AND INDOOR OR OUTDOOR
<br />SWIMMING POOLS WHERE THE BOTTOM EXPOSED
<br />EDGE OF THE GLAZING IS LESS THAN 60 INCHES
<br />MEASURED VERTICALLY ABOVE ANY STANDING OR
<br />WALKING SURFACE, SHALL BE CONSIDERED A
<br />HAZARDOUS LOCATION. G.C. TO VERIFY IF
<br />HOMEOWNER SELECTS ANY OF THESE ITEMS
<br />LISTED. IF ANY OF THESE ITEMS LISTED IS
<br />INSTALLED, SUCH GLAZING FACING THOSE ITEMS IS
<br />TO BE TEMPERED
<br />• PER FBC R312.2, PROVIDE WINDOW FALL
<br />PROTECTION IN ACCORDANCE WITH R312.2.1 AND
<br />R312.2.2
<br />• GAS OPT. PER COMMUNITY. VERIFY WITH BLDR
<br />• C.J. = RECOMMENDED MASONRY CONTROL JOINT
<br />LOCATION
<br />• ALL FINISHES, MATERIALS, HOUSEWRAP, WINDOW
<br />AND DOOR FLASHING, TAPING AND SEALANTS TO BE
<br />INSTALLED PER BUILDER PROVIDED
<br />SPECIFICATIONS OR MFR WRITTEN INSTRUCTIONS
<br />• ALL FINISH DETAILS & TYPICAL PLAN NOTES
<br />PROVIDED BY BUILDER IN ACCORDANCE WITH
<br />TYPICAL BUILDER SPECIFICATIONS
<br />• REFER TO STRUCTURAL ENGINEERING DRAWINGS
<br />FOR ALL EXTERIOR WALL STUD SPECIES, SIZES AND
<br />SPACING
<br />0
<br />U
<br />O 0
<br />APEX
<br />O N
<br />O �
<br />, N
<br />N
<br />co I�lll�
<br />ILL �
<br />w
<br />J
<br />J �
<br />true design studios
<br />O
<br />U 9000 REGENCY SQUARE BLVD.
<br />SUITE 100, JACKSONVILLE, FL 32211 OI
<br />o
<br />O
<br />w
<br />I—
<br />•�
<br />DaRtHOMON'
<br />s j
<br />00
<br />Q
<br />C�
<br />U
<br />w
<br />U'
<br />W
<br />cr
<br />O
<br />O
<br />O
<br />IT
<br />rl�
<br />O C!)
<br />z
<br />W
<br />W
<br />L.L.
<br />W
<br />W
<br />Z W
<br />co
<br />co
<br />LU 0 �
<br />x 0 W
<br />w Q O
<br />z Q
<br />LU W 0 0
<br />J W LLJ
<br />2
<br />W W
<br />O
<br />X
<br />U_ LL
<br />z Q
<br />O z
<br />O
<br />W
<br />O
<br />1-
<br />a
<br />z
<br />O
<br />CIL
<br />U
<br />W
<br />p
<br />w
<br />Abbott Park
<br />O
<br />U
<br />U_
<br />LOT 011-04-1 B
<br />o
<br />Q
<br />— w
<br />-
<br />1_
<br />U
<br />Q
<br />z
<br />z
<br />>-
<br />O
<br />U)
<br />W
<br />PROJECT NO:
<br />2021.012602
<br />w
<br />z
<br />U
<br />DRAWN: -
<br />CD
<br />-- O
<br />wCHKD:
<br />o
<br />LO
<br />X
<br />JAC
<br />w
<br />w
<br />a
<br />a
<br />co
<br />U)
<br />O
<br />m
<br />z
<br />o �
<br />w
<br />z
<br />� � o
<br />O
<br />w
<br />2 (D
<br />Q z
<br />z
<br />0 11-01-2021 p�
<br />w
<br />CD
<br />U REVISIONS:
<br />ILL. - -
<br />No. Description Date w
<br />U) J
<br />(D - U)
<br />O I—
<br />z Z
<br />= O
<br />U
<br />w
<br />I—
<br />X
<br />w AOOO
<br />a
<br />Q
<br />
|