|
FOLD UP WEATHER
<br />RESISTIVE BARRIER & WEATHER RESISTIVE
<br />TEMPORARILY SECURE BARRIER i_SLOPE - WINDOW UNIT
<br />WEATHER DOOR ROUGH OPENING FLASHING REQUIREMENTS
<br />RESISITIVE 0.3 in: 12.0 in
<br />BARRIER WOOD FRAME CONSTR. R703.1 General. Exterior walls shall provide the building with a weather -resistant exterior wall envelope. The exterior wall envelope shall include
<br />TAPE EXTERIOR SELF -ADHERED FLASHING 3/4"-1" BEAD OF CONSTR. (O.6 Cm : 30.5 Cm) flashing as described in Section R703.4. A water -resistive barrier is described as a material behind an exterior wall covering that is intended to
<br />s SHEATHING BY LAPPING DOWN ADHESIVE TO BE APPLIED UNDER SELF -ADHERED FLASHING resist liquid water that has penetrated behind the exterior covering from further intruding into the exterior wall assembly. An exterior wall covering
<br />OVER RIM JOIST AND UP THRESHOLD OF DOOR AND RETURN q p g 9 Y 9
<br />(ASSEMBLEDWINDOW) WALL BY 6 IN. UP JAMB 6". USE LIQUID NAIL BRAND EXTERIOR is described as a material or assembly of materials applied on the exterior side of exterior walls for the purpose of providing a weather -resistive
<br />2 OR EQUAL WEATHER PROOF CAULKING CEMT. FIN. barrier, insulation, or for aesthetics, including but not limited to, veneers, siding, exterior insulation and finish systems, architectural trim and
<br />2
<br />O WEATHER SELF -ADHERED FLASHING BUILDING PAPER embellishments such as cornices, soffits, and fascias.
<br />RESISITIVE
<br />z BARRIER SEAL TOPS OF JOISTS 1 WIRE LATH
<br />UNDER DECKING SUBFLOOR R703.2 Water -resistive barrier. One layer of No. 15 asphalt felt, free from holes and breaks, complying with ASTM D226 for Type 1 felt or other
<br />SELF -ADHERED FLASHING (SEE DETAIL WP07) ° ° approved water -resistive barrier shall be applied over studs or sheathing of all exterior walls. Such felt or material shall be applied horizontally,
<br />with the upper layer lapped over the lower layer not less than 2 inches (51 mm). Where joints occur, felt shall be lapped not less than 6 inches
<br />HEAD FLASHING TIE-IN INSTRUXTIONS: (152 mm). The felt or other approved material shall be continuous to the top of walls and terminated at penetrations and building appendages in a
<br />1. Cut, fold up & temporarily secure weather resistive RIM JOIST
<br />barrier above header to allow for flashing manner to meet the requirements of the exterior wall envelope as described in Section R703.1.
<br />THESE DETAILS ARE GENERIC AND installation
<br />MEANT TO SHOW GENERAL FLASHING 2. Self -adhered flashing plus head flashing under 1 1 R703.7.3 Water -resistive barriers shall be installed as required in Section R703.2 and, where applied over wood -based sheathing, shall include a
<br />AND WATERPROOFING METHODS TO weather resistive barrier
<br />3. Fold weather resistive barrier back over head water -resistive vapor -permeable barrier with a performance at least equivalent to two layers of Grade D paper. The individual layers shall be
<br />BE USED. flashing and seal with tape 2 2 Q installed independently such that each layer provides a separate continuous plane and any flashing (installed in accordance with Section R703.4)
<br />intended to drain to the water -resistive barrier is directed between the layers.
<br />Scale: NTS . SELF -ADHERED FLASHING p pp 9 q 9
<br />SELF -ADHERED FLASHING SELF -ADHERED FLASHING Exception: Where the water -resistive barrier that is applied over wood -based sheathing has a water resistance equal to or rester than
<br />FLANGED WINDOW 1 EXTERIOR DOOR WITH DECK - SECTION A 1 CEMT. FINISH SILL/ POTSHELF/ CHIMNEY SHOULDER 1 that of 60-minute Grade D paper and is separated from the stucco by an intervening, substantially nonwater-absorbing layer or designed
<br />FLASHING INSTALLATION AFTER WEATHER RESISTIVE BARRIER drainage space.
<br />EXTERIOR SHEATHING MECHANICALLY FASTEN IF RUBBERIZED RUBBERIZED ASPHALT
<br />EXTERIOR SHEATHING 3/4'A" BEAD OF CONSTR. INSTALL SELF -ADHERED NEEDED IN CORNERS ASPHALT ADHESIVE ADHESIVE
<br />�I ADHESIVE TO BE APPLIED UNDER FLASHING JAMB & HEAD THROUGH SELF -ADHERED R703.4 Flashing. Approved corrosion -resistant flashing shall be applied shingle -fashion in a manner to prevent entry of water into the wall cavity
<br />THRESHOLD OF DOOR AND RETURN FLASHING, SEE FLASHING SELF -ADHERED FLASHING or penetration of water to the building structural framing components. Self -adhered membranes used as flashing shall comply with AAMA 711. All
<br />UP JAMB 6". USE LIQUID NAIL BRAND FLANGED WINDOW OR EQUAL WEATHER PROOF CAULKING (SEE DETAIL WPOt) exterior fenestration products shall be sealed at the juncture with the building wall with a sealant complying with AAMA 800 or ASTM C920 Class
<br />REFER TO TECHNICAL SCORED 25 Grade NS or greater for proper joint expansion and contraction, ASTM C1281, AAMA 812, or other approved standard as appropriate for the
<br />LETTER ON CHEMICAL ° Q RELEASE PAPER type of sealant. Fluid -applied membranes used as flashing in exterior walls shall comply with AAMA 714. The flashing shall extend to the surface
<br />COMPATIBILITY pp g p Y g
<br />SELF -ADHERED FLASHING SELF -ADHERED FLASHING, B of the exterior wall finish. Approved corrosion resistant flashings shall be installed at the following locations:
<br />�° (BEFORE FOLDING, SCORE
<br />EXTEND MINIMUM 6" RELEASE PAPER TO EXPOSE 1. Exterior window and door openings. Flashing at exterior window and door openings shall extend to the surface of the exterior wall finish
<br />ADHESIVE AS SHOWN) 9
<br />BOTTOM OF TICALLY FROM or to the water -resistive barrier complying with Section 703.2 for subsequent drainage. Mechanically attached flexible flashings shall
<br />O THRESHOLD comply with AAMA 712. Flashing at exterior window and door openings shall be installed in accordance with one or more of the following:
<br />2 3 1.1 The fenestration manufacturer's installation and flashing instructions, or for applications not addressed in the fenestration
<br />SECTION -A (SEE DETAIL WP02) manufacturer's instructions, in accordance with the flashing manufacturer's instructions. Where flashing instructions or details
<br />SELF -ADHERED FLASHING are not provided, pan flashing shall be installed at the sill of exterior window and door openings. Pan flashing shall be sealed or
<br />p 2 sloped in such a manner as to direct water to the surface of the exterior wall finish or to the water resistive barrier for subsequent
<br />drainage. Openings using pan flashing shall incorporate flashing or protection at the head and sides.
<br />z SELF -ADHERED FLASHING 5 1.2. In accordance with the flashing design or method of a registered design professional.
<br />NAILING FLANGE O 4 1.3. In accordance with other approved methods.
<br />1.4 In accordance with FMA/AAMA 100, FMA/ AAMA 200, FMA/WDMA 250, FMA/AAMA/ WDMA 300 or FMA/AAMA/WDMA 400.
<br />DO NOT FLASH OVER 2 SEAL TOPS OF JOISTS 1 6 2. At the intersection of chimneys or other masonry construction with frame or stucco walls, with projecting lips on both sides under stucco
<br />BOTTOM NAILING UNDER DECKING
<br />FLANGE 8 (SEE DETAIL WP07) Z 7 copings.
<br />3. Under and at the ends of masonry, wood or metal copings and sills.
<br />SELF -ADHERED FLASHING SELF -ADHERED FLASHING , SELF -ADHERED FLASHING �' • 4. Continuously above all projecting wood trim.
<br />HALF ROUND WINDOW EXTERIOR DOOR WITH DECK INSIDE CORNER
<br />5. Where exterior porches, decks or stairs attach to a wall or floor assembly of wood -frame construction.
<br />6. At wall and roof intersections.
<br />Ground
<br />7. At built-in gutters.
<br />SELF-ADHERED FLASHING
<br />DECK JOIST
<br />SELF -ADHERED FLASHING
<br />PRODUCTS DETAILS
<br />TWO LAYERS OF FELT OR ONE LAYER OF HOUSE WRAP AND
<br />ONE LAYER OF FELT ARE REQUIRED BEHIND STUCCO, FBC
<br />R703.2.1 AND FBCR 703.7.3
<br />Detail Instructions
<br />Refer to the number marked as O in each detail that corresponds to the
<br />numbered items in the list of instructions below:
<br />1. Install self -adhered flashing in order as shown by numbers
<br />2. Install flashing and weather resistive barrier to form water shedding
<br />laps
<br />3. Self -adhered flashing can be substituted for building paper
<br />4. Split the release paper using the ripcord (Split release on demand,
<br />embedded in the adhesive layer) - for ease of installation and to
<br />minimize scoring cuts
<br />5. Remove all release paper per standard installation instructions and
<br />adhere to substrate using a square piece of flashing material (6" x 6"
<br />Minimum)
<br />6. Fold as shown by arrows
<br />7. Angle of corner may vary, adjust folding of the flashing accordingly to
<br />fit tight to corner
<br />8. Mechanically fasten as necessary
<br />2x FRAMEWALL
<br />TILE FINISH-
<br />1/2" DUROCK-
<br />8" CMU
<br />4"OR8"CMU
<br />(PER SEAT DEPTH)
<br />FILL WITH GROUT -
<br />SLOPED MUD BED -
<br />VINYL SHOWER PAN
<br />SLOP
<br />--
<br />E
<br />AM
<br />SELF-ADHER
<br />Q)
<br />1'4' PER PLAN
<br />SHOWER SEAT
<br />SELF -ADHERED FLASHING
<br />OUTSIDE CORNER
<br />Z
<br />W
<br />t1
<br />W
<br />U
<br />W
<br />Lu
<br />0
<br />U)
<br />SELF -ADHERED FLASHING
<br />PATCH
<br />HERED FLASHING
<br />PLASTER STOP r�
<br />CONTINUOUS BACKER
<br />ROD & SEALANT
<br />A
<br />0
<br />0
<br />0
<br />0
<br />a
<br />FOUNDATION WEEP SCREED
<br />STRIP OF SAF
<br />DRAINAGE PLANE WRB
<br />BOND BREAK WRB
<br />SF LATH
<br />WRAP DP WRB ONTO
<br />THE VERTICAL
<br />SURFACE TO TOP OF
<br />FLANGE AS AN AIR
<br />BARRIER
<br />�. 3-1/2" INCH FLANGE
<br />THIS,
<br />NATU
<br />DO Nt
<br />DRIP
<br />ACCE
<br />SOFFIT/CANTILEVER
<br />Water Resistant Barrier
<br />Lath
<br />Sheathing
<br />Stucco
<br />LEGEND
<br />SELF ADHERED FLASHING (SAF) ti
<br />DRAINAGE PLANE (DP) WEATHER RESISTANT
<br />BARRIER (WRB) - -
<br />BOND BREAK WEATHER RESISTANT BARRIER -
<br />SELF FURRING (SF) LATH
<br />PLASTER ACCESSORY
<br />SHEATHING,'OSB', PLYWOOD, DENSGLASS
<br />Cement Plaster
<br />in accordance
<br />with ASTMC926
<br />over wood 2nd
<br />floor
<br />TRUCTURAL FRAMING
<br />TRUCTURAL SHEATHING
<br />TRIP OF SAF
<br />RAINAGE PLANE WRB
<br />OND BREAK WRB
<br />F LATH
<br />THESE DETAILS ARE GENERIC AND MEANT TO SHOW GENERAL
<br />FLASHING AND WATERPROOFING METHODS TO BE USED.
<br />.-..0•.O!.!o.
<br />Cement
<br />Plaster
<br />over block
<br />1 st floor
<br />7/8" Cement Plaster
<br />in accordance with
<br />ASTMC926
<br />- Felt backed metal
<br />lathe in accordance
<br />with ASTM C1063
<br />Building Paper
<br />-7/16" O.S.B.
<br />sheathing
<br />Metal
<br />Flashing
<br />Weep Screed
<br />Installed As Per
<br />Manufact. Specs.
<br />Maintain
<br />Bottom of
<br />Weep Screed
<br />1 1/2" to 2"
<br />Above Roof
<br />Sheathing
<br />Note:
<br />The building paper and metal lath must be
<br />installed over the top of the weep screed.
<br />WEEP SCREED DETAIL
<br />SCALE: NOT TO SCALE
<br />7/8" Cement Plaster
<br />in accordance with
<br />ASTMC926
<br />Felt backed metal
<br />lathe in accordance
<br />with ASTMC1063
<br />Building Paper
<br />7/16" O.S.B.
<br />sheathing
<br />-Stampede or similar
<br />cauk bottom
<br />joint only
<br />Weep Screed
<br />Installed As Per
<br />Manufact. Specs.
<br />1/2" Cementitious
<br />Decorative Finish
<br />All inside and
<br />outside corner will
<br />need to be miter
<br />cut and caulked all
<br />butt joints need to
<br />becaulked using
<br />Stampede or sim.
<br />caulk for all
<br />0
<br />CV
<br />0
<br />CV
<br />00
<br />N
<br />0
<br />To the best of the Engineers knowledge, information and belief,
<br />the structural plans and specifications contained
<br />within these
<br />drawings comply with the 2017 Florida Building Code -
<br />Residential 6th Edition. Engineer's signature and
<br />seal is only for
<br />the structural engineering portions of the drawing pages bearing
<br />Engineer's signature and seal.
<br />° �
<br />W
<br />F
<br />8
<br />m
<br />N p r- °D
<br />p p p T
<br />N r,
<br />J
<br /># W LL. LL
<br />0
<br />9)
<br />:"rno
<br />9LLN
<br />-Jxtww
<br />LLLn.d
<br />QZ
<br />> n r�n
<br />ao
<br />13
<br />�r&_'E*
<br />YLLWoo
<br />z
<br />OM0o
<br />W
<br />.2o
<br />caC C',W
<br />p�0_J
<br />Zi
<br />2Ec'
<br />V N O
<br />Q O
<br />Z
<br />04
<br />��
<br />U ♦- J
<br />❑��❑
<br />W
<br />N
<br />Z S
<br />z
<br />z
<br />J th
<br />d. N
<br />N
<br />- M
<br />z 2
<br />0 LL
<br />a
<br />U
<br />a
<br />O
<br />to
<br />V1
<br />w F
<br />c i
<br />= N
<br />o
<br />ws
<br />r_
<br />U °'
<br />w rn
<br />E
<br />o
<br />=
<br />z;�
<br />U o
<br />°
<br />CD�ZcoZ
<br />U_
<br />ce E
<br />O
<br />E
<br />�°
<br />�
<br /><�
<br />Z®
<br />0�
<br />U
<br /><_
<br />o E
<br />U
<br />a0
<br />p
<br />°Z
<br />N
<br />�o
<br />a
<br />rW
<br />y� L
<br />ra
<br />C,OC
<br />Q ❑
<br />Z$ Z
<br />O Y
<br />='m
<br />m�
<br />o
<br />z LL
<br />Z
<br />J
<br />aw
<br />W
<br />Cn-
<br />d
<br />S_
<br />��
<br />oM
<br />LL
<br /><
<br />1Z
<br />5U
<br />a
<br />0.
<br />0
<br />�°�
<br />J
<br />aZ
<br />w<
<br />=3
<br />>°
<br />o
<br />co
<br />a
<br />01
<br />0
<br />MMJ
<br />O c
<br />i
<br />a)
<br />> cM
<br />6
<br />m
<br />m
<br />L
<br />�
<br />�
<br />T
<br />0
<br />0-
<br />C m
<br />O
<br />T°t
<br />CV
<br />o
<br />Li)
<br />° v
<br />J+ N
<br />r
<br />L1')
<br />7
<br />oo
<br />N N
<br />LO
<br />r
<br />r
<br />��•
<br />E V
<br />T f
<br />M
<br />o
<br />E
<br />m
<br />c r
<br />�,;
<br />z
<br />Z
<br />E Ocu
<br />E
<br />ca
<br />U J
<br />Q 0
<br />J
<br />JOB
<br />NO:
<br />20-0554
<br />SCALE :
<br />AS NOTED
<br />SHEET NO.
<br />W P
<br />fib II tl r _, 1 '. 111-,1 1 i 11 1 1 1 11 1 I 1-F
<br />
|