|
DIVISION 1 GENERAL NOTES I DIVISION 4 MASONRY
<br />SECTION 01340 SHOP DRAWINGS, PRODUCT DATA AND SAMPLES NONE SPECIFIED
<br />PART 1 GENERAL
<br />121 REQUIREMENTS INCLUDED DIVISION 5 METALS
<br />A. SUBMIT SHOP DRAWINGS, PRODUCT DATA AND SAMPLES REQUIRED BY CONTRACT DOCUMENTS, OR A$
<br />NECESSARY WHERE NOT INDICATED, 50 ARCHITECT CAN REVIEW, SELECT, CHECK FOR CONFORMANCE, NONE SPECIFIED
<br />ETC., AS REQUIRED.
<br />122 RELATED REQUIREMENTS DIVISION ro WOOD and PLASTICS
<br />A. DESIGNATED IN THE CONSTRUCTION SCHEDULE, OR IN A SEPARATE COORDINATE SCHEDULE, THE DATES FOR
<br />SUBMISSION AND THE DATES THAT REVIEWED SHOP DRAWINGS, PRODUCT DATA AND SAMPLES WILL BE NEEDE
<br />ALLOW SUFFICIENT TIME IN THE SCHEDULE FOR ARCHITECT REVIEW AND P05515LE RE5U5MITTAL5 IF REQUIRED.
<br />1.03 SHOP DRAWINGS
<br />A. DRAWINGS SHALL BE PRESENTED IN A CLEAR AND THOROUGH MANNER
<br />1. DETAILS SHALL BE IDENTIFIED BY REFERENCE TO SHEET AND DETAIL, SCHEDULE OR ROOM NUMBERS
<br />SHOWN ON CONTRACT DRAWINGS.
<br />2. SHEET SHALL BE LABELED WITH CORRECT JOB NAME, LOCATION, ARCHITECT'S PROJECT NUMBER, AND
<br />SUBCONTRACTOR'S COMPANY NAME, ADDRESS, 'PHONE NUMBER AND NAME OF RESPONSIBLE
<br />REPRESENTATIVE OF COMPANY.
<br />3. DRAWINGS, DETAILS, ETC. SHALL CLEARLY ILLUSTRATE ALL COMPONENTS AND ADJACENT COMPONENTS
<br />OF THE WORK
<br />1.04 PRODUCT DATA
<br />A. PREPARATION:
<br />1. CLEARLY MARK EACH COPY TO IDENTIFY PERTINENT PRODUCTS OR MODELS WHICH ARE SPECIFICALLY
<br />COVERED BY THE SUBMITTAL. REFERENCE ALL NUMBERS TO CORRESPOND TO THOSE IN CONTRACT
<br />DOCUMENTS.
<br />2. SHOW PERFORMANCE CHARACTERISTICS AND CAPACITIES.
<br />3. SHOW DIMENSIONS AND CLEARANCES REQUIRED.
<br />4. SHOW WIRING OR PIPING DIAGRAMS AND CONTROLS,
<br />5. DELETE MODEL NUMBERS, DIAGRAMS, DETAILS, ETC., NOT APPLICABLE TO THE SUBMITTAL.
<br />B. MANUFACTURER'S STANDARD SCHEMATIC DRAWINGS AND DIAGRAMS:
<br />1. MODIFY DRAWINGS AND DIAGRAMS TO DELETE INFORMATION WHICH 15 NOT APPLICABLE TO THE WORK
<br />2. SUPPLEMENT STANDARD INFORMATION TO PROVIDE INFORMATION SPECIFICALLY APPLICABLE
<br />TO THE WORK
<br />In SAMPLES
<br />A. OFFICE SAMPLES SHALL BE OF SIZE INDICATED, OR OF SUFFICIENT SIZE AND QUANTITY TO CLEARLY
<br />ILLUSTRATE :
<br />1. FUNCTIONAL CHARACTERISTICS OF THE PRODUCT, WITH INTEGRALLY RELATED PARTS AND ATTACHMENT
<br />DEVICES AND TECHNIQUES.
<br />2. FULL RANGE OF COLOR, TEXTURE AND PATTERN FOR ARCHITECT SELECTION AT NO ADDITIONAL COST.
<br />SUBMIT ONLY SPECIFIED COLOR RANGE IF DIFFERENT FROM MANUFACTURER'S STANDARD RANGE.
<br />B. ALL SAMPLES OF A PARTICULAR PRODUCT, ASSEMBLY, UNIT, ETC., SHALL BE SUBMITTED AT THE SAME
<br />TIME TO ALLOW PROPER REVIEW AND COMPARISON BETWEEN SAMPLES.
<br />1.06 SUBMITTALS
<br />A. PERMITS, LICEN5E5, AND CERTIFICATES: FOR THE OWNER'S RECORDS, SUBMIT COPIES OF PERMITS,
<br />LICENSES, CERTIFICATIONS, INSPECTION REPORTS, RELEASES, JURISDICTIONAL SETTLEMENTS, NOTICES,
<br />RECEIPTS FOR FEE PAYMENTS, JUDGMENTS, AND SIMILAR DOCUMENTS, CORRESPONDENCE AND RECORDS
<br />ESTABLISHED IN CONJUNCTION WITH COMPLIANCE WITH STANDARDS AND REGULATIONS BEARING UPON
<br />PERFORMANCE OF THE WORK
<br />1.01 CONTRACTOR RESPONSIBILITIES
<br />SECTION 06410 CUSTOM CASEWORK
<br />PART 1 CABINETS
<br />1.01 DOOR FRONTS, DRAWER FRONTS, KICKS AND SPLASHES
<br />A. KICKS, SPLASHES AND COUNTER TOPS SHALL BE 3/4" THICK PLYWOOD SURFACED WITH HIGH PRESSURE
<br />DECORATIVE PLASTIC LAMINATE ON EXTERIOR FACE AND EDGES.
<br />B. DOOR FRONTS, DRAWER FRONTS AND CABINET BODIES SHALL BE 5/6" BLACK MELAMINE WITH HIGH
<br />PRESSURE DECORATIVE PLASTIC LAMINATE ON EXTERIOR FACES AND EDGES.
<br />C. STYLE SHALL BE FLUSH OVERLAY WITH SQUARE EDGES.
<br />1.02 CABINET BACK5
<br />A. 5/6" WHITE MELAMINE BOXES ON BASE AND UPPERS. FINISH INTERIOR FACE TO MATCH CABINET INTERIOR.
<br />1.03 DRAWERS
<br />A. DRAWER FRAMES SHALL BE GRASS ZARGEN DRAWER SLIDE SYSTEM OR EQUIVALENT. ALL EXPOSED
<br />VIEW PORTIONS SHALL BE FINISHED TO MATCH INTERIOR OF CABINET BODIES.
<br />1.04 SHELVES, DIVIDERS, AND BOTTOMS
<br />A. SHELVES ON THE INTERIOR OF CABINETS (BEHIND DOORS), BOTTOM IN CABINET, AND VERTICAL DIVIDERS
<br />SHALL BE 5/8" WHITE MELAMINE. EXPOSED FACES SHALL MATCH CABINET BODY INTERIOR FINISH, ALL
<br />EXPOSED FRONT EDGES, INCLUDING SHELF EDGES, SHALL BE FINISHED WITH ONE (1) TAPED FRONT EDGE.
<br />1.05 PLASTIC LAMINATE
<br />A. 1/16" THICK MATERIAL ON HORIZONTAL .5URFACE5 AND 1/32" ON VERTICAL SURFACES.
<br />(GENERAL NOTE: ALL EXTERIOR CORNERS OF COUNTER TOPS TO HAVE A RADIUS OF 1 1/2").
<br />PART 2 PRODUCTS
<br />2.01 HARDWARE
<br />A. HINGES: "GRASS 120 DEGREE SNAP -ON 3,000 SERIES" FULL OVERLAY SELF CLOSING
<br />B. PULL5 : 3" BRUSHED ALUMINUM FINISH BY STANLEY OR EQUAL FINAL SELECTION TBD
<br />C. DRAWER GLIDES : SEE SPECIFICATION ABOVE
<br />D. LOCK : NATIONAL LOCK "C8123-26D (DOOR),'CS-8138-26D (DRAWER).
<br />E. KEYBOARD DRAWER ACCURIDE CBERGO - TRAY 200 KEYBOARD SYSTEM BY ACCURIDE
<br />PART 3 INSTALLATION
<br />3.01 INSTALLATION
<br />A. PROVIDE WOOD BACK BLOCKING AT PROPER LOCATIONS IN PARTITIONS FOR CASEWORK ATTACHMENT.
<br />END OF SECTION Oro410
<br />DIVISION I THERMAL IAL AND MOISTURE
<br />A. REVIEW SHOP DRAWINGS, PRODUCT DATA AND SAMPLES PRIOR TO SUBMISSION. PROTECTION
<br />B. DETERMINE AND VERIFY: T _ %
<br />1. FIELD MEASUREMENTS.
<br />2. FIELD CONSTRUCTION CRITERIA.
<br />3. CATALOG NUMBERS AND SIMILAR DATA.
<br />4. CONFORMANCE WITH SPECIFICATIONS AND DRAWINGS.
<br />C. COORDINATE EACH SUBMITTAL WITH REQUIREMENTS OF THE WORK AND THE CONTRACT DOCUMENTS.
<br />DO NOT SUBMIT NON -CONFORMING PRODUCTS.
<br />D NOTIFY THE ARCHITECT IN WRITING, AT THE TIME OF SUBMISSION, OF ANY DEVIATIONS IN THE SUBMITTALS FROM
<br />REQUIREMENTS OF THE CONTRACT DOCUMENTS, OR OF ANY DISCREPANCIES WITHIN THE CONTRACT DOCUMENTS.
<br />E. BEGIN NO FABRICATION OR WORK WHICH REQUIRES SUBMITTALS UNTIL RETURN OF SUBMITTALS WITH
<br />ARCHITECT'S CONFORMANCE REVIEW.
<br />F. SUBMITTALS NOT PROPERLY REVIEWED BY CONTRACTOR FOR CONFORMANCE WITH CONTRACT DOCUMENTS
<br />SHALL BE RETURNED WITHOUT ARCHITECT'S REVIEW OR ACCEPTANCE.
<br />1.08 SUBMISSION REQUIREMENTS
<br />A. MAKE SUBMITTALS PROMPTLY IN ACCORDANCE WITH APPROVED SCHEDULE, AND IN SUCH SEQUENCE
<br />AS TO CAUSE NO DELAY IN THE WORK OR IN THE WORK OF ANY OTHER CONTRACTOR
<br />B. NUMBER OF SUBMITTALS REQUIRED:
<br />1. SHOP DRAWINGS: SUBMIT THE NUMBER OF OPAQUE REPRODUCTIONS WHICH THE CONTRACTOR REQUIRES,
<br />PLUS THREE (3) COPIES WHICH WILL BE RETAINED BY THE ARCHITECT. MAXIMUM ACCEPTABLE
<br />SIZE IS 24" x 36" FOR ANY ONE SHEET.
<br />2. PRODUCT DATA: SUBMIT THE NUMBER OF COPIES WHICH THE CONTRACTOR REQUIRES, PLUS THREE (3)
<br />WHICH WILL BE RETAINED BY THE ARCHITECT.
<br />3. SAMPLES: SUBMIT THE NUMBER STATED IN EACH SPECIFICATION SECTION. IF NO NUMBER IS GIVEN,
<br />VERIFY CORRECT NUMBER WITH ARCHITECT PRIOR TO SUBMITTAL. MINIMUM OF Two (2) SAMPLES.
<br />4. PROVIDE SUBMITTALS AS REQUIRED BY THE INDIVIDUAL SECTION, BUT NO LESS THAN THAT STATED ABOVE.
<br />C. SUBMITTALS SHALL CONTAIN:
<br />1. THE DATE OF SUBMISSION AND THE DATES OF ANY PREVIOUS SUBMISSIONS.
<br />2. THE PROJECT TITLE AND NUMBER
<br />3. CONTRACT IDENTIFICATION.
<br />4. THE NAMES OF:
<br />a. CONTRACTOR
<br />b. SUBCONTRACTOR
<br />c. SUPPLIER
<br />d. MANUFACTURER
<br />5. IDENTIFICATION OF THE PRODUCT, WITH THE SPECIFICATION SECTION NUMBER
<br />6. FIELD DIMENSIONS, CLEARLY IDENTIFIED AS SUCH,
<br />1. RELATION TO ADJACENT OR CRITICAL FEATURES OF THE WORK OR MATERIALS.
<br />8. APPLICABLE STANDARDS SUCH AS, BUT NOT LIMITED TO ASTM OR FEDERAL SPECIFICATION NUMBERS.
<br />9. IDENTIFICATION OF DEVIATIONS FROM CONTRACT DOCUMENTS.
<br />10, IDENTIFICATION OF OPTIONS AVAILABLE, BUT NOT INDICATED IN THE SPECIFICATIONS, SUCH AS
<br />COLOR, FINISH, TEXTURE, ETC. WITH COMPLETE SAMPLES OR LISTING INCLUDED IN THE SUBMITTAL FOR
<br />ARCHITECT'S SELECTION.
<br />11. INDICATION OF TERMS TO BE INCLUDED IN THE WORK AND SHOWN ON THE SHOP DRAWINGS SHALL BE
<br />DIMENSIONED AND COORDINATED FOR PROPER FIT AND TIMELY INCLUSION.
<br />12, IDENTIFICATION OF REVISIONS ON SUBMITTALS.
<br />13. AN 8" x 3" BLANK SPACE FOR CONTRACTOR AND ARCHITECT STAMPS.
<br />14. CONTRACTOR'S STAMPS, INITIALED OR SIGN, CERTIFYING THE REVIEW OF SUBMITTAL, VERIFICATION OF
<br />PRODUCTS, FIELD MEASUREMENTS AND FIELD CONSTRUCTION CRITERIA, AND COORDINATION OF
<br />THE INFORMATION WITHIN THE SUBMITTAL WITH REQUIREMENTS OF THE WORK AND OF CONTRACT DOCUMENTS.
<br />1.09 RE5UBM1S510N REQUIREMENTS
<br />A. MAKE ANY CORRECTIONS OR CHANGES IN THE SUBMITTALS REQUIRED BY THE ARCHITECT AND RESUBMIT
<br />UNTIL ACCEPTED.
<br />B. SHOP DRAWINGS AND PRODUCT DATA:
<br />1. REVISE INITIAL DRAWINGS OR DATA, AND RESUBMIT AS SPECIFIED FOR THE INITIAL SUBMITTAL.
<br />2. INDICATE ANY CHANGES WHICH HAVE BEEN MADE OTHER THAN THOSE REQUESTED BY THE ARCHITECT.
<br />C. SAMPLES: SUBMIT NEW SAMPLES AS REQUIRED FOR INITIAL SUBMITTAL.
<br />1.10 DISTRIBUTION '
<br />A DISTRIBUTE REPRODUCTION OF SHOP DRAWINGS AND COPIES OF PRODUCT DATA WHICH CARRY THE
<br />ARCHITECT'S STAMP OF CONFORMANCE TO:
<br />SECTION 08211 FLUSH WOOD DOORS
<br />PART 1 GENERAL
<br />1.01 GENERAL
<br />A. DO NOT DELIVER DOORS OR INSTALL UNTIL CONDITIONS FOR TEMPERATURE AND RELATIVE HUMIDITY HAVE
<br />BEEN STABILIZED AND WILL BE MAINTAINED IN STORAGE AND INSTALLATION AREAS DURING REMAINDER OF
<br />CONSTRUCTION PERIOD.
<br />1.02 INTERIOR FLUSH WOOD SOLID CORE DOORS
<br />A. PROVIDE DOORS 1 3/4", 5 OR 1 PLY, PARTICLE BOARD CORE, CONFORMING TO AWI SECTION 1300
<br />FACE VENEER SHALL BE PREMIUM STAIN GRADE BIRCH. EDGE STRIPS SHALL BE HARDWOOD. STILE
<br />EDGE SHALL NOT BE LESS THAN 2 3/5" THICK EDGE BEFORE TRIMMING AND SHALL BE SPECIES
<br />COMPATIBLE WITH FACE VENEER TOP AND BOTTOM AND BOTTOM EDGE SHALL NOT BE LESS THAN 1
<br />115" BEFORE TRIMMING.
<br />END OF SECTION 01340
<br />1.03 HARDWARE
<br />A. PREPARE DOOR TO RECEIVE HARDWARE IN ACCORDANCE WITH THE DOOR SCHEDULE AND
<br />TEMPLATES PROVIDED BY THE HARDWARE MANUFACTURER
<br />B. PREPARATION OF FIRE DOORS TO BE DONE AT THE FACTORY OR AN APPROVED "UL" OR
<br />DIVISION 2 8 I TE WO "WARNOCK HERSEY" SHOP.
<br />END OF SECTION 08211
<br />SECTION 01210 BUILDING INSULATION
<br />PART 1 GENERAL
<br />1.01 GENERAL
<br />A COAT INSULATION EXPOSED TO VIEW IN FINISH WORK WITH CEMENTITIOUS COATING. INSTALL COATING STRICTLY
<br />IN ACCORDANCE WITH COATING MANUFACTURER'S INSTRUCTION. APPLY COATING APPROXIMATELY 3/16"
<br />THICK TEXTURE SURFACE WITH A PAINT ROLLER
<br />122 GENERAL BUILDING INSULATION
<br />A. RIGID BOARD INSULATION TO BE 1" CELOTEX - TUFF "R"
<br />B. BLANKET INSULATION TO BE UNFACED, MINERAL FIBER WITH THERMOSETTING RESINS, TYPE 1. MINERAL FIBER
<br />SHALL BE MANUFACTURED FROM GLASS.
<br />C. APPLY INSULATION UNITS COMPLYING WITH MANUFACTURER'S RECOMMENDATIONS. INSTALL BLANKET
<br />INSULATION IN STUD WALLS. BOND UNITS TO SUBSTRATE WITH ADHESIVE OR USE MECHANICAL ANCHORAGE
<br />TO PROVIDE PERMANENT PLACEMENT.
<br />1.03 SOUND ATTENUATING INSULATION
<br />A SOUND INSULATION SHALL BE AS MANUFACTURED BY OWEN5-CORNING FIBERGLASS, FIBERGLASS NOISE
<br />BARRIER BATTS. INSTALL IN STUD WALLS AND CEILINGS WHERE INDICATED ON THE DRAWINGS.
<br />FIT INSULATION TIGHTLY BETWEEN STUD MEMBERS.
<br />END OF SECTION 07210
<br />SECTION 01900 JOINT SEALERS
<br />PART 1 GENERAL
<br />1.01 GENERAL
<br />A PROVIDE JOINT SEALERS, JOINT FILLERS, AND OTHER RELATED MATERIALS THAT ARE COMPATIBLE WITH
<br />ONE ANOTHER AND WITH JOINT SUBSTRATES UNDER CONDITIONS OF SERVICE AND APPLICATION, AS
<br />DEMONSTRATED BY SEALANT MANUFACTURER BASED ON TESTING AND FIELD EXPERIENCE. PROVIDE
<br />COLORS TO MATCH ADJACENT FINISH SURFACES.
<br />B. PROVIDE SEALANT BACKINGS OF MATERIAL AND TYPE WHICH ARE NONSTAINING, ARE COMPATIBLE WITH
<br />JOINT SUBSTRATE, SEALANTS, PRIMERS, AND OTHER FILLERS, AND ARE APPROVED FOR APPLICATIONS
<br />INDICATED BY SEALANT MANUFACTURER
<br />C. SEALANTS: SEALANTS SHALL BE AS FOLLOWS OR EQUAL:
<br />1. ONE -PART POLYURETHANE:
<br />2. TWO-PART POLYURETHANE:
<br />3. SILICONE:
<br />D. COMPLY WITH JOINT SEALER MANUFACTURER'S PRINTED INSTALLATION INSTRUCTION APPLICABLE TO
<br />PRODUCTS AND APPLICATIONS INDICATED. CLEAN OUT JOINTS IMMEDIATELY BEFORE INSTALLING JOINT
<br />SEALERS. PRIME WHERE RECOMMENDED BY SEALER MANUFACTURER DO NOT ALLOW MIGRATION OF
<br />PRIMER ONTO ADJACENT SURFACES. MASK WHERE REQUIRED TO PROTECT ADJOINING SURFACES FOR
<br />STAINING OR DAMAGE BY CLEANING METHODS TO REMOVE SMEARS.
<br />E. APPLY SEALANTS IN A MANNER SO THAT APPEARANCE IS THAT OF A SMOOTH, UNIFORM, SLIGHTLY
<br />CONCAVE BEAD. TOOL WITH CAULKING TOOL AS REQUIRED WITHIN 10 MINUTES OF APPLICATION. ALL
<br />SEALED JOINTS ARE TO BE WATER -TIGHT.
<br />F. BACKER ROD: POLYETHYLENE FOAM BACKER ROD, NONSTAINING, CLOSED -CELL, EXPANDED
<br />POLYETHYLENE FOAM AS MANUFACTURED BY DOW CHEMICAL ETHLFOAM. FURNISH WITH ROUND EDGE IN
<br />THICKNESS REQUIRED.
<br />END OF SECTION 01900
<br />DIVISION 8 DOORS ,AND WINDOWS
<br />I. JOB SITE FILE,
<br />2. RECORD DOCUMENTS FILE.
<br />3. SUBCONTRACTORS.
<br />4. SUPPLIER OR FABRICATOR
<br />5. OWNER (TO BE DISTRIBUTED BY THE ARCHITECT).
<br />1.11 ARCHITECT'S DUTIES
<br />A. REVIEW SUBMITTALS WITH REASONABLE PROMPTNESS AND IN ACCORD WITH SCHEDULE. ALLOW A MINIMUM
<br />OF TEN (10) WORKING DAYS FOR REVIEW, UNLESS SPECIAL HANDLING IS ARRANGED IN ADVANCE.
<br />B. AFFIX STAMP AND INITIALS OR SIGNATURE, AND INDICATE REQUIREMENTS FOR RESUBMITTAL OR
<br />CONFORMANCE OF SUBMITTAL. ACCEPTANCE IS FOR GENERAL CONFORMANCE WITH DE51GN CONCEPT AND
<br />GENERAL COMPLIANCE WITH THE CONTRACT DOCUMENTS. QUANTITIES AND DIMENSIONS OF MATERIALS
<br />WILL NOT BE REVIEWED. ACCEPTANCE OF A SUBMITTAL DOES NOT WAIVE OR ALTER THE REQUIREMENTS
<br />OF THE CONTRACT DOCUMENTS.
<br />C. RETURN SUBMITTALS TO CONTRACTOR FOR DISTRIBUTION OR FOR RESUBMISSION.
<br />NONE SPECIFIED
<br />DIVISION 3 CONCRETE
<br />NONE SPECIFIED
<br />SECTION 08110 FINISH HARDWARE
<br />PART 1 GENERAL
<br />1.01 GENERAL
<br />A. OBTAIN EACH TYPE OF AS SPECIFIED IN THE DO R/HARDWARE SCHEDULE HARDWARE FROM A SINGLE
<br />MANUFACTURER, ALTHOUGH SEVERAL MAY BE INDICATED AS OFFERING PRODUCTS COMPLYING WITH THE
<br />REQUIREMENTS.
<br />B. FURNISH ALL HARDWARE, IN THEIR ORIGINAL PACT AGING, COMPLETE WITH ACCESORIE6 OF PROPER SIZE AND
<br />DESIGN REQUIRED FOR THE PURPOSE FOR WHICI'THEY ARE TO BE USED AND WITH ALL SCREWS, SHIELDS, AND
<br />OTHER ANCHORAGE DEVICES NECESSARY FOR A', COMPLETE INSTALLATION. HARDWARE SCHEDULE SHOWN
<br />ON THE DRAWINGS.
<br />C. INSTALL EACH HARDWARE ITEM IN COMPLIANCE OITH THE NATIONAL BUILDERS HARDWARE ASSOCIATION AND
<br />THE MANUFACTURER'S INSTRUCTIONS AND RECOMMENDATIONS. WHEREVER CUTTING AND FITTING 15 REQUIRED TO
<br />INSTALL HARDWARE ONTO OR INTO SURFACES WHICH ARE LATER TO BE PAINTED OR FINISHED IN ANOTHER
<br />WAY, COORDINATED REMOVAL, STORAGE, AND REINSTALLATION OR APPLICATION OF SURFACE PROTECTIONS
<br />WITH FINISHING WORK
<br />D. SET UNITS LEVEL, PLUMB AND TRUE TO LINE AND LOCATION. ADJUST AND REINFORCE THE ATTACHMENT
<br />SUBSTRATE AS NECESSARY FOR PROPER INSTALLATION AND OPERATION. DRILL AND COUNTERSINK UNITS NOT
<br />FACTORY PREPARED FOR ANCHORAGE FASTENERS. SPACE FASTENERS AND ANCHORS IN ACCORDANCE WITH
<br />INDUSTRY STANDARDS. SET THRESHOLDS FOR EXTERIOR DOORS IN FULL BED OF BUTYL -RUBBER OF
<br />POLYIO55UTYLENE MASTIC SEALANT.
<br />E. ADJUST AND CHECK EACH OPERATING ITEM OF HARDWARE AND' EACH DOOR TO ENSURE PROPER OPERATION.
<br />REPLACE UNITS THAT CANNOT BE ADJUSTED TO OPERATE FREELY AND SMOOTHLY A5 NTENDED FOR THE
<br />APPLICATION MADE. INSTRUCT OWNERS IN PROPER ADJUSTMENT:AND MAINTENANCE OF HARDWARE DURING,
<br />FINAL ADJUSTMENT.
<br />1.02 KEYING
<br />A. KEYING SHALL BE PER THE OWNERS REQUIREMENTS. TAG KEYS AND PROVIDE TO OWNER AT SUBSTANTIAL
<br />COMPLETION.
<br />1.03 GUARANTEE
<br />A. PROVIDE ONE-YEAR GUARANTEE FOR ALL HARDWARE. PERIOD OF GUARANTEE SHALL BEGIN FROM DATE OF
<br />OWNER'S ACCEPTANCE.
<br />END OF SECTION 08110
<br />DIVISION 9 FINISHES
<br />SECTION 09110 METAL SYSTEMS ,
<br />METAL STUDS
<br />A. AT INTERIOR METAL STUD PARTITIONS, UNLESS OTHERWISE SHOWN ON THE DRAWINGS, PROVIDE
<br />STANDARD PUNCH STEEL STUDS OF THE SIZES SHOWN ON THE DRAWINGS, EITHER HOT -DIP
<br />GALVANIZED OR FACTORY PRE -PAINT: 25 GA.1 NLESS SHOWN OTHERWISE ON THE DRAWINGS. 20
<br />GA. AT ALL DOOR OPENINGS,
<br />B. ACCESSORIES: PROVIDE ALL ACCESSORIES INCLUDING, BUT NOT NECESSARILY LIMITED TO,
<br />TRACKS, CLIPS, ANCHORS, FASTENING DEVICES, ROUND ATTENUATION PENCIL RODS AND
<br />RESILIENT CLIPS, AND OTHER ACCESSORIES REQUIRED FOR A COMPLETE AND PROPER
<br />INSTALLATION, AND AS RECOMMENDED BY THE MANUFACTURER OF THE STEEL STUDS USED.
<br />C. MEET OR EXCEED MINIMUM REQUIREMENTS OF FEDERAL SPEC. QQ-5498 AND FEDERAL SPEC.
<br />QQ-5-115D, CLASS D.
<br />METAL TRIM
<br />A. FORM FROM GALVANIZED STEEL NOT LIGHTER THAN 26 GAUGE, COMPLYING WITH FEDERAL SPEC
<br />QQ-5-115, CLASS D.
<br />B. CASING BEADS: U.S.G. 0200-8.
<br />END OF SECTION 09110
<br />SECTION 09250 GYPSUM WALLBOARD
<br />PART 1 GENERAL
<br />1.01 GENERAL
<br />A. GYPSUM WALLBOARD WORK SHALL CONFORI TO,THE GYPSUM ASSOCIATION "RECOMMENDED
<br />SPECIFICATIONS FOR THE APPLICATION AND FINISHING OF GYPSUM WALLBOARD."
<br />B. EXAMINE SUBSTRATES TO WHICH DRY WALL CONSTRUCTION ATTACHES OR ABUTTS, PRESET HOLLOW METAL'
<br />FRAMES, CAST-IN-ANCORS, AND STRUCTURAL FRAMING FOR COMPLIANCE WITH REQUIREMENTS FOR
<br />INSTALLATION TOLERANCE AND OTHER CONDITIONS AFFECTING PERFORMANCE OF DRY WALL
<br />CONSTRUCTION. DO NOT PROCEED WITH INSTALLATION UNTIL UNSATISFACTORY CONDITIONS HAVE BEEN
<br />CORRECTED.
<br />C. DO NOT TAPE AND FINISH GYPSUM BOARD WHEN THE TEMPERATURE IS BELOW 60 DEGREES FAHRENHEIT.
<br />THE TEMPERATURE OF THE ROOMS SHALL BE HELD AT 60 DEGREES FAHRENHEIT FOR 48 HOURS BEFORE
<br />TAPING AND FINISHING 15 TO BEGIN. MAINTAIN 60 DEGREES FAHRENHEIT DURING AND AFTER INSTALLATION.
<br />VENTILATES AS REQUIRED TO REMOVE EXCESS HUMIDITY.
<br />1.02 GYPSUM WALLBOARD
<br />A. GYPSUM WALLBOARD SHALL BE MANUFACTURED BY US. GYPSUM. WALLBOARD IS TO MEET. ASTM C36-84A
<br />AND SS-L-30d 1/2 INCHES THICK, 48 INCHES WIDE WITH TAPERED EDGES.
<br />B. AT FIRE RATED PARTITIONS INSTALL WALLBOARD TO MEET SEPARATE REQUIREMENTS, USE TYPE 111, GRADE
<br />X CLA56 1, 5/8 INCHES THICK FIRE RETARDANT WALLBOARD.
<br />C. INSTALL GYPSUM BOARD WITH TRUE, EVEN SURFACES AND STRAIGHT, SHARP CORNERS. USE FULL LENGTH
<br />BOARDS WHERE POSSIBLE. END JOINTS ON THE SAME SIDE OF A WALL SHALL BE STAGGERED AND JOINTS
<br />ON OPPOSITE SIDE SHALL NOT OCCUR OVER THErSAME SUPPORT. DO NOT LOCATE NORMAL END JOINTS AT
<br />EDGE OF OPENINGS. FORM JOINTS NEATLY. BUTT BOARDS TOGETHER BUT DO NOT FORCE INTO PLACE. DO
<br />NOT BUTT EDGES AGAINST TAPERED EDGES. NO JOINT SHALL HAVE A GAP GREATER THAN 1/4 INCH.
<br />D. IN GENERAL, INSTALL GYPSUM BOARD ON CEILING BEFORE WALLS. CONSTRUCT CEILINGS WITH LONG
<br />DIMENSION OF GYPSUM BOARD APPLIED AT RIGHT ANGLES TO SUPPORT.
<br />E. SCREW GYPSUM BOARD TO FRAMING WITH SCREWS NOT OVER 8 INCHES ON CENTER FASTEN GYPSUM
<br />BOARD BEGINNING AT THE CENTER AND WORK TOWARDS OUTER EDGES. HOLD BOARD FIRMLY AGAINST
<br />WOOD FRAMING WHILE FASTENING. FASTENERS AT,EDGES OF BOARDS SHALL BE 1/2 INCH FROM THE EDGE.
<br />F. OPENINGS FOR ELECTRICAL DEVICES, PIPING, GRILLS, AND REGISTERS SHALL BE ACCURATELY LOCATED
<br />AND NEATLY MADE TO CLOSELY FIT THE DEVICES AND BE COMPLETELY COVERED BY PLATES AND
<br />ESCUTCHEONS.
<br />1.03 TRIM PIECES
<br />A. PROVIDE TRIM ACCESSORIES OF THE SIZES REQUIRED FOR THE WALLBOARD APPLICATION AS
<br />MANUFACTURED BY U.S. GYPSUM. PROVIDE DUR-A-BEAD COMER BEAD AT EXTERNAL CORNERS AND NO,
<br />200-A METAL CASING BEAD WHERE WALLBOARD iABUTTS OTHER MATERIALS.
<br />1.04 FASTENERS
<br />A. PROVIDE SCREWS, NAILS, CLIPS, TIES, AND OTHER FASTENERS AS RECOMMENDED BY THE GYPSUM
<br />MANUFACTURER
<br />1.05 JOINT TREATMENT 5Y5TEM5
<br />A. SYSTEM SHALL BE PERFORATED TAPE AND CEMENT RECOMMENDED THE GYPSUM MANUFACTURER
<br />B. APPLY MATERIALS IN STRICT ACCORDANCE TO MANUFACTURER'S RECOMMENDATIONS. FILL JOINTS WITH
<br />JOINT COMPOUND, EMBED PERFORATED TAPE AND APPLY A SKIM COAT OF JOINT COMPOUND OVER TAPE.
<br />APPLY TWO ADDITIONAL COATS OF JOINT COMPOUND ALLOWING AT LEAST 24 HOURS BETWEEN EACH COAT.
<br />SAND EACH COAT. FINISH SURFACES SHALL BE UNIFORMLY SMOOTH, TRUE AND IN SATISFACTORY CONDITION
<br />TO RECEIVE PAINT,
<br />END OF SECTION 013250
<br />SECTION OWOO CERAMIC TILE
<br />PART 1 GENERAL
<br />I.01 GENERAL
<br />A. CERAMIC AND TYPES ARE INDICATED ON THE DRAWINGS AND ARE FROM A SINGLE MANUFACTURER OTHER
<br />MANUFACTURERS WILL NOT BE CONSIDERED.
<br />B. DELIVER MATERIALS IN ORIGINAL CONTAINERS WITH SEALS UNBROKEN AND LABELS INTACT UNTIL TIME OF
<br />USES. ENGAGE AN EXPERIENCED INSTALLER WHO HAS SUCCESSFULLY COMPLETED TILE INSTALLATIONS
<br />51MILAR IN MATERIAL, DESIGN, AND EXTENT TO THAT INDICATED FOR THE PROJECT.
<br />C. COMPLY WITH PARTS OF ANSI 105 SERIES OF FINE*,{NSTALLATION STANDARDS INCLUDED UNDER "AMERICAN
<br />NATIONAL STANDARD SPECIFICATIONS FOR THE INSTALLER OF CERAMIC TILE" THAT APPLY TO TYPE OF
<br />SETTING AND GROUT MATERIALS AND METHODS INDICATED. TILE MAY BE THIN -SET.
<br />1.02 MORTAR AND GROUT
<br />A. MORTAR SHALL BE PORTLAND CEMENT ASTM C150, TYPE 1. GROUT SHALL BE ACID RESISTANT UPCO
<br />HYDROMENT, TYPE AS RECOMMENDED BY THE MANUFACTURER FOR THE SPECIFIC TYPE OF TILE AND
<br />METHOD OF INSTALLATION. COLR FOR FLOOR TILE 15 SPECIFIED ON THE DRAWINGS.
<br />B. DO NOT GROUT TILE UNTIL TILE IS FIRMLY SET. SOAK OR DAMPEN JOINTS OF THE TILE TO BE GROUTED WITH
<br />PORTLAND CEMENT GROUT. SOAK OR DAMPEN OTHER JOINTS AS RECOMMENDED BY THE GROUT
<br />MANUFACTURER FORCE GROUT INTO JOINT LINES COMPLETELY IDILING JOINTS WITH COMPACTED GROUT AND
<br />COVERING MORTAR FINISH JOINTS OF SQUARE EDGED TILE FLUSH WITH SURFACE. STRIKE OFF TOOL JOINTS
<br />OF CUSHION EDGED TILE TO DEPTH OF CUSHION, FILL GAPS AND SKIPS, AND RETOOL.
<br />1.03 CLEANING
<br />A. UPON COMPLETION OF THE PLACEMENT AND GROUTING, CLEAN TILE SURFACE 50 THAT THEY ARE FREE OF
<br />FOREIGN MATTER REMOVE LATEX-PORTLAND CEMENT GROUT RESIDUE FROM TILE AS SOON AS POSSIBLE
<br />UNGLAZED TILE MAY BE CLEANED WITH ACID SOLUTIONS ONLY WHEN PERMITTED BY TILE AND GROUT
<br />MANUFACTURER'S PRINTED INSTRUCTIONS, BUT SOONER THAN 14 DAYS AFTER INSTALLATION. FLUSH SURFACE
<br />WITH CLEAN WATER BEFORE AND AFTER CLEANING.
<br />END OF SECTION 09300
<br />SECTION 09511 ACOUSTIC PANEL CEILINGS
<br />PART 1 GENERAL
<br />1.01 GENERAL
<br />A. COORDINATE LAYOUT AND INSTALLATION OF ACOUSTICAL CEILING UNITS AND SUSPENSION SYSTEM
<br />COMPPONENTS WITH ETHER CONSTRUCTION THAT PENETRATES CEILINGS OR 15 SUPPORTED BY THEM,
<br />INCLUDING LIGHT FIXTURES AND HVAC EQUIPMENT.
<br />122 MINERAL -FIBER ACOU57!CAL PANELS
<br />A. PROVIDE ACOUSTICi� PANELS AS MANUFACTURED BY AR'1STRONG CIRRUS ANGLED TEGULAR
<br />24 INCHES BY 24 INIC~S 3/4 INCHES THICK WHITE, REFER TO DRAWINGS FOR LIMITS OF TILE
<br />INSTALLATION.
<br />B. INSTALL IN STRICT 4ORDANCE WITH THE MANUFACTURER'S PRINTED INSTRUCTIONS. ARRANGE
<br />ACOUSTICAL UNITS *b ORIENT DIRECTIONAL PATTERN OF TILES FOR A UNIFORM APPEARANCE. REST
<br />PANELS ON FLANGEStR INVERTED TEES WITH TILE UNITS FITTING NEATLY AGAINST BUTTING SURFACE
<br />AND SUPPORT BY WALL ANGLES.
<br />1.03 METAL SUSPENSION SYSTEM
<br />A PROVIDE SYSTEM AS MANUFACTURED BY ARMSTRONG SUSPENSION SYSTEM SHALL BE EXPOSED
<br />TEE -GRID, DOUBLE -WEB, INTERMEDIATE DUTY (ASTM C635), ELECTROGALVANIZED, COLD -ROLLED STEEL,
<br />15/16 INCHES WIDE, CAPPED BOTTOM FLANGE. WHITE IN COLOR SYSTEM TO INCLUDE ALL CROSS TEES,
<br />BRIDGING TREES, INTERSECTION CLIPS, SPLICES, COMPLETE EXPOSED GRID SYSTEM.
<br />B. LAY OUT PATTERN IN ACCORDANCE WITH THE DRAWINGS, LEVEL, TRUE TO PLANE, AND AT THE REQUIRED
<br />ELEVATION. FRAME AROUND ALL OPENINGS IN CEILING LIGHTS AND GRILLES WITH MAIN RUNNERS. HANGERS
<br />ARE TO BE SPACED AT 4'-0" ON CENTER MAXIMUM. PROVIDE ADDITIONAL HANGERS AS REQUIRED TO
<br />SUPPORT LIGHT FIXTURES AND HVAC REGISTERS AND GRILLES AND INTERFERENCES OF DUCT WORK
<br />C, SECURES WIRES BY LOOPING AND WIRE -TYING, EITHER DIRECTLY TO STRUCTURES OR TO INSERTS, EYE
<br />SCREWS, OR OTHER DEVICES APPROPRIATE FOR SUBSTRATE. SCREW ATTACH EDGE MOLDINGS TO
<br />SUBSTRATE AT INTERVALS NOT OVER I6 INCHES ON CENTER AND NOT MORE THAN 3 INCHES FROM ENDS.
<br />LEVEL GRID TO A TOLERANCE OF 1/8" IN 12 FEET.
<br />END OF SECTION 09511
<br />SECTION 09650 VINYL COMPOSITION TILE
<br />PART 1 GENERAL
<br />1.01 SUMMARY
<br />A PROVIDE TYPE AND STYLE AS SCHEDULED IN THE FINISH MATERIAL SCHEDULE.
<br />B. ADHESIVES.
<br />1, PROVIDE WHITE LATEX CARPET ADHESIVE SUCH AS W.W. HENRY COMPANY NO 356, ROBERTS
<br />COMPANY NO.41-0504, OR AN EQUAL APPROVED BY THE ARCHITECT AND RECOMMENDED
<br />FOR THE PURPOSE BY THE MANUFACTURER OF THE SELECTED CARPET.
<br />2. PROVIDE SEAM ADHESIVE SUCH A$ W.W. HENRY COMPANY NO.246, ROBERTS COMPANY NO.
<br />41-0502, OR AN EQUAL APPROVED BY THE ARCHITECT AND RECOMMENDED FOR THE PURPOSE
<br />BY THE MANUFACTURER OF THE SELECTED CARPET.
<br />C. AT INTERSECTION OF CARPET AND FLOOR TILE, PROVIDE ROPPE COMPANY, INC. VINYL TILE CARPET J011
<br />h88 OR EQUIVALENT.
<br />D. PROVIDE OTHER MATERIALS, NOT SPECIFICALLY DESCRIBED BUT REQUIRED FOR A COMPLETE AND
<br />PROPER INSTALLATION, AS SELECTED BY THE CONTRACTOR, SUBJECT TO THE APPROVAL OF THE
<br />ARCHITECT.
<br />E. ALLOW THE OWNER TO INSPECT AND SELECT FROM SCRAP CARPET REMAINING AFTER THE INSTALLATION.
<br />BUNDLE, WRAP IN BURLAP, AND DELIVER TO THE OWNER THE CARPET SCRAPS 50 SELECTED.
<br />END OF SECTION 09650
<br />SECTION 096W CARPETING
<br />PART 1 GENERAL
<br />1.01 SUMMARY
<br />A PROVIDE TYPE AND STYLE AS SCHEDULED IN THE FINISH MATERIAL SCHEDULE.
<br />B. ADHESIVES.
<br />1. PROVIDE WHITE LATEX CARPET ADHESIVE SUCH AS W.W. HENRY COMPANY NO 356, ROBERTS
<br />COMPANY NO.41-0504, OR AN EQUAL APPROVED BY THE ARCHITECT AND RECOMMENDED
<br />FOR THE PURPOSE BY THE MANUFACTURER OF THE SELECTED CARPET.
<br />2. PROVIDE SEAM ADHESIVE SUCH AS W.W. HENRY COMPANY NO.246, ROBERTS COMPANY NO.
<br />41-0502, OR AN EQUAL APPROVED BY THE ARCHITECT AND RECOMMENDED FOR THE PURPOSE
<br />BY THE MANUFACTURER OF THE SELECTED CARPET.
<br />C. AT INTERSECTION OF CARPET AND FLOOR TILE, PROVIDE ROPPE COMPANY, INC. VINYL TILE CARPET JO[
<br />188 OR EQUIVALENT.
<br />D. PROVIDE OTHER MATERIALS, NOT SPECIFICALLY DESCRIBED BUT REQUIRED FOR A COMPLETE AND
<br />PROPER INSTALLATION, AS SELECTED BY THE CONTRACTOR, SUBJECT TO THE APPROVAL OF THE
<br />ARCHITECT.
<br />E. ALLOW THE OWNER TO INSPECT AND SELECT FROM SCRAP CARPET REMAINING AFTER THE INSTALLATION,
<br />BUNDLE, WRAP IN BURLAP, AND DELIVER TO THE OWNER THE CARPET SCRAPS SO SELECTED.
<br />END OF SECTION 09680
<br />SECTION 09900 PAINTNG
<br />PART 1 GENERAL
<br />IDI GENERAL
<br />A. IT 15 THE INTENT OF THIS SPECIFICATION TO PRODUCE A PREMIUM JOB, WHICH WILL PROVIDE THE MAXIMUM
<br />DURABILITY, WHICH CAN REASONABLY BE EXPECTED FROM A PAINTED SURFACE.
<br />B "PAINT" INCLUDES COATING SYSTEMS MATERIALS, PRIMERS, EMULSIONS, ENAMELS, STAINS, SEALERS, AND
<br />FILLERS, AND OTHER APPLIED MATERIALS WHETHER USED AS PRIME, INTERMEDIATE, OR FIN16H COAT.
<br />C. SPECIFIED PRODUCTS BELOW ARE MANUFACTURED BY SHERWIN WILLIAMS, EXCEPT WHERE OTHER
<br />MANUFACTURERS ARE INDICATED, AND ESTABLISH A STANDARD OF QUALITY. EQUIVALENT PRODUCTS OF
<br />OTHER ACCEPTABLE MANUFACTURERS MAY NOT BE USED UNLESS APPROVED BY ARCHITECT.
<br />D. PROVIDE BEST GRADE AND QUALITY MATERIALS AND PRODUCTS MANUFACTURED BY SHERWIN WILLIAMS.
<br />MATCH COLORS AS INDICATED ON THE DRAWINGS. USE PREMIXED PAINTS INSOFAR AS POSSIBLE. THIN ONLY
<br />AS PERMITTED ANY MANUFACTURER'S LABEL INSTRUCTIONS, AND AVOID UNNECESSARY THINNING.
<br />E. PROTECT FINISHED SURFACES, WORK OF OTHER TRADES, AND PROPERTY OF THE OWNER FROM DAMAGE ANI
<br />DEFACEMENT. COVER FLOORS AND FIXED EQUIPMENT WITH DROP CLOTHS.
<br />F. PREPARE SURFACES ACCORDING TO PAINT MANUFACTURER'S INSTRUCTIONS. EXAMINE FACTORY FINISHED
<br />AND PRIMED SURFACES TO BE PAINTED, AND VERIFY COMPATIBILITY OF EXISTING MATERIAL WITH PAINT TO
<br />BE APPLIED, APPLY PAINT IN STRICT ACCORDANCE WITH THE MANUFACTURER'S PRINTED INSTRUCTIONS
<br />ONLY TO SURFACES WHICH ARE THOROUGHLY DRY, SMOOTH, EVEN, CLEAN, FREE OF DUST AND PROPERLY
<br />PREPARED TO RECEIVE THE INTENDED FINISH.
<br />1.02 PAINTING
<br />A ACCEPTABLE MATERIALS
<br />1. ALL PAINTING TO BE SCHEDULED IN THE FINISH SCHEDULE.
<br />2. EQUIVALENT PRODUCTS OF THE FOLLOWING ARE AL60 ACCEPTABLE:
<br />PRATT 6 LANBERTT
<br />GLIDDEN
<br />PORTER
<br />BENJAMINE MOORE
<br />B. UNDERCOATS AND THINNERS
<br />I. PROVIDE UNDERCOAT PAINT PRODUCED BY THE SAME MANUFACTURER
<br />OF FINISH COAT.
<br />2. USE ONLY THINNERS RECOMMENDED BY THE PAINT MANUFACTURER AND USE ONLY
<br />THE RECOMMENDED LIMITS.
<br />C. COLOR SCHEDULES
<br />1. PROVIDE PAINTING AS SCHEDULED IN THE FINISH MATERIALS SCHEDULE.
<br />a. ON GYPSUM DRYWALL, USE:
<br />1. FIRST COAT - PIGMENTED PRIMER/SEALER
<br />2. SECOND COAT - ACRYLIC LATEX ENAMEL
<br />3. THIRD COAT - ACRYLIC LATEX ENAMEL
<br />b. ON FERROUS METAL, USE:
<br />1. FIRST COAT - RUST INHIBITIVE ALKYD METAL PRIMER
<br />2. SECOND COAT - SEMI -GLOSS ALKYD ENAMEL
<br />3. THIRD COAT - SEMI -GLOSS ALKYD ENAMEL
<br />c. ON WOOD DOORS, USE:
<br />I. FIRST COAT - STAIN (SEE FINISH SCHEDULE)
<br />2. SECOND COAT - STAIN (SEE FINISH SCHEDULE)
<br />3. THIRD COAT - VARNISH LOW SHEEN "RUBBED EFFECT"
<br />END OF SECTION 09900
<br />DIVISION 10 SPECIALTIES
<br />SECTION 10522 FIRE EXTINGUISHERS
<br />PART 1 GENERAL
<br />1.01 SUBMITTALS
<br />A. PRODUCT DATA: REQUIRED
<br />B. SHOP DRAWINGS: NOT REQUIRED
<br />C. SAMPLES: NOT REQUIRED
<br />PART 2 PRODUCTS
<br />2.01 MANUFACTURER5/PRODUCT5
<br />A COORDINATE WITH LOCAL MUNICIPALITIES AND PROVIDE FIRE EXTINGUISHERS.
<br />B. FIRE EXTINGUISHERS: SEE DRAWINGS FOR SPECIFICATIONS,
<br />PART 3 EXECUTION
<br />3.01 SCHEDULES
<br />A. INSTALL AS REQUIRED.
<br />END OF SECTION 10522
<br />DIVISION 11 EQUIPMENT
<br />NONE SPECIFIED
<br />DIVISION 12 FURNISHINGS
<br />NONE SPECIFIED
<br />DIVISION 13
<br />NONE SPECIFIED
<br />DIVISION 14
<br />NONE SPECIFIED
<br />DIVISION 1s
<br />SEE MECHANICAL
<br />DIVISION 116
<br />SEE ELECTRICAL
<br />SPECIAL CONSTRUCTION
<br />CONVEYING SYSTEMS
<br />MECHAN I CAL
<br />ELECTRICAL
<br />END OF SPECIFICATIONS
<br />REVISIONS BY
<br />CO
<br />Y M N
<br />�, o r• E
<br />u
<br />!� ! o
<br />it d v
<br />o
<br />co 3
<br />3 r 3
<br />oSN .
<br />r.
<br />v
<br />r �El o
<br />cn
<br />-
<br />� via
<br />w
<br />Q
<br />00
<br />N
<br />O
<br />> 0 0
<br />NL.. af
<br />.
<br />Cn
<br />.--r
<br />Q �
<br />0 U
<br />C4
<br />�� W a��
<br />U Z M
<br />v U
<br />0O Q O Ln N
<br />p LLJ
<br />0 C LLL
<br />L W _J 'o p
<br />'0 M -< vi
<br />Q L0 _
<br />W :EM
<br />i _J fV
<br />v L.i
<br />a.
<br />Date: 08. 13. 13
<br />Scale: AS NOTED
<br />Project Mgr: AAY
<br />Drawn: DC
<br />Job: 13-46
<br />Sheet
<br />N1
<br />
|