|
DIVISION 1 GENERAL NOTES
<br />DIVISION Z SITE WORK
<br />DIVISION 10 SPECIALTIES
<br />1.03 INTERIOR FIRE RATED WOOD DOORS
<br />1.05 JOINT TREATMENT SYSTEMS
<br />A 20 MINUTE - PROVIDE DOORS 1 3/4", 5 OR -1 PLY, PARTICLE BOARD CORE,
<br />A SYSTEM SHALL BE PERFORATED TAPE AND CEMENT RECOMMENDED THE
<br />SECTION 01340 SHOP DRAWWA, PRODUCT DATA AND SA VLES
<br />NONE SPECIFIED
<br />CONFORMING TO AWI SECTION 1300, FACE VENEER SHALL BE PREMIUM GRADE, TO
<br />MATCH EXISTING. EDGE STRIPS SHALL BE HARDWOOD, STILE EDGE SHALL NOT BE
<br />GYPSUM MANUFACTURER
<br />SECTION kM22 FIRE EXTWA116HM
<br />PART I GENERAL
<br />LESS THAN 2 3/8" THICK EDGE BEFORE TRIMMING AND SHALL BE SPECIES
<br />B. APPLY MATERIALS IN STRICT ACCORDANCE TO MANUFACTURER'S
<br />PART 1 GENERAL
<br />COMPATIBLE WITH FACE VENEER TOP AND BOTTOM AND BOTTOM EDGE SHALL NOT
<br />RECOMMENDATIONS. FILL JOINTS WITH JOINT COMPOUND, EMBED PERT --GRATED
<br />1.01 REQUIREMENTS INCLUDED
<br />A SUBMIT SHOP DATA AND SAMPLES REQUIRED BY CONTRACT
<br />DIVISION 3 CONCRETE
<br />BE LESS THAN 1 1/8" BEFORE TRIMMING. APPROPRIATE FIRE DOOR LABEL TO BE
<br />TAPE AND APPLY A SKIM COAT OF JOINT COMPOUND OVER TAPE. APPLY TWO
<br />1.01 SUBMITTALS
<br />DRAWINGS, PRODUCT
<br />ATTACHED.
<br />ADDITIONAL COATS OF JOINT COMPOUND ALLOWING AT LEAST 24 HOURS
<br />A PRODUCT DATA: REQUIRED
<br />DOCUMENTS, OR AS NECESSARY WHERE NOT INDICATED, SO ARCHITECT CAN REVIEW,
<br />BETWEEN EACH COAT. SAND EACH COAT. FINISH SURFACES SHALL BE UNIFORMLY
<br />B. SHOP DRAWINGS: NOT REQUIRED
<br />SELECT, CHECK FOR CONFORMANCE, ETC., AS REQUIRED.
<br />B. 45 THRU 90 MINUTE - PROVIDE DOORS 1 3/4", 5 OR -1 PLY, NONCOMBUSTIBLE,
<br />SMOOTH, TRUE AND IN SATISFACTORY CONDITION TO RECEIVE PAINT.
<br />C. SAMPLES: NOT REQUIRED
<br />102 RELATED REQUIREMENTS
<br />NOW SPECIFIED
<br />NON -ASBESTOS MINERAL CORE, ENGINEERED TO MEET LABELING REQUIREMENTS.
<br />PART 2 PRODUCTS
<br />A DESIGNATED IN THE CONSTRUCTION SCHEDULE, OR IN A SEPARATE COORDINATE
<br />CONFORMING TO NFPA 80 AND AWI SECTION 1300 FACE VENEER SHALL BE
<br />PREMIUM GRADE, STAIN GRADE RED OAK EDGE STRIPS SHALL BE 1 1/2" WITH 5/8"
<br />END OF SECTION 09250
<br />�'1I�/(SIGN
<br />DIVISION
<br />SCHEDULE, THE DALESS FOR SUBMISSION AND THE DATES THAT REVIEWED SHOP
<br />DRAWINGS, PRODUCT DATA AND SAMPLES WILL BE NEEDED. ALLOW SUFFICIENT TIME
<br />MATCHING HARDWOOD EDGE AND 7/8" COMPOSITE BACKING. APPROPRIATE FIRE
<br />DOOR LABEL TO BE ATTACHED.
<br />SECTION f' WII ACOUSTIC PANEL CEILIN_*
<br />2.01 MANUFACTURERS/PRODUCTS
<br />A COORDINATE WITH LOCAL MUNICIPALITIES AND PROVIDE FIRE EXTINGUISHERS.
<br />IN THE SCHEDULE FOR ARCHITECT REVIEW AND POSSIBLE RESUBMITTALS IF
<br />PART I GENERAL
<br />B. FIRE EXTINGUISHERS: SEE DRAWINGS FOR SPECIFICATIONS.
<br />REQUIRED.
<br />I.04 HARDWARE
<br />PART 3 EXECUTION
<br />1.03 SHOP DRAWINGS
<br />NOW SPECIFIED
<br />A PREPARE DOOR TO RECEIVE HARDWARE IN ACCORDANCE WITH THE DOOR
<br />.
<br />101 GENERAL
<br />3.01 SCHEDULES
<br />A DRAWINGS SHALL BE PRESENTED IN A CLEAR AND THOROUGH MANNER
<br />SCHEDULE AND TEMPLATES PROVIDED BY THE HARDWARE MANUFACTURER.
<br />A COORDINATE LAYOUT AND INSTALLATION OF ACOUSTICAL CEILING UNITS
<br />A INSTALL AS REQUIRED.
<br />I. DETAILS SHALL BE IDENTIFIED BY REFERENCE TO SHEET AND DETAIL, SCHEDULE
<br />PREPARATION OF FIRE DOORS TO BE DONE AT THE FACTORY OR AN APPROVED
<br />AND SUSPENSION SYSTEM GOMPOONENTS WITH OTHER CONSTRUCTION THAT
<br />OR CONTRACT DRAWINGS.B.
<br />OSHALL
<br />PULP OR "WARNOGK HERSEY" SHOP.
<br />PENETRATES CEILINGS OR IS SUPPORTED BY THEM, INCLUDING LIGHT
<br />END OF SECTION 10522
<br />2. SWEET BEE LABELED WITH CORRECT JOB NAME, LOCATION, ARCHITECT'S
<br />FIXTURES AND HVAC EQUIPMENT.
<br />PROJECT NUMBER, AND SUBCONTRACTOR'S COMPANY NAME, ADDRESS, PHONE
<br />Q METALS
<br />DIVISION 5 METALS
<br />END OF SECTION 05211
<br />NUMBER AND NAME OF RESPONSIBLE REPRESENTATIVE OF COMPANY.
<br />102 MINERAL -FIBER ACOUSTICAL PANELS
<br />3. DRAWINGS, DETAILS, ETC. SHALL CLEARLY ILLUSTRATE ALL COMPONENTS AND
<br />SECTION M110 FINISH WARDWARE
<br />A PROVIDE ACOUSTICAL PANELS AS MANUFACTURED TO MATCH EXISTING, 24
<br />DIVISION 11 EQUIPMENT
<br />ADJACENT COMPONENTS OF THE WOW.ECIFIED
<br />NONE SPECIFIED
<br />INCHES BY 24 INCHES I INCH THICK WHITE. REFER TO DRAWINGS FOR LIMITS
<br />1.04 PRODUCT DATA
<br />PART I GENERAL
<br />OF TILE INSTALLATION.
<br />A PREPARATION:
<br />B. INSTALL IN STRICT ACCORDANCE WITH THE MANUFACTURER'S PRINTED
<br />Y MARK EACH COPY TO IDENTIFY PERTINENT PRODUCTS OR-MODIELS�y
<br />L CLEAWHICH RARESPECIFICALLY
<br />� p /� �t Q
<br />DIVISION >S WOOD and PLASTICS S 1 ICS
<br />101 GENERAL
<br />INSTRUCTIONS. ARRANGE ACOUSTICAL UNITS AND ORIENT DIRECTIONAL
<br />NONE SPECIFIED
<br />COVERED BY THE SUBMITTAL. REFERENCE ALL
<br />A OBTAIN EACH TYPE OF AS SPECIFIED IN THE pOOR/HARDWARE SCHEDULE HARDWARE FROM A SINGLE
<br />PATTERN OF TILES FOR A UNIFORM APPEARANCE. REST PANELS ON
<br />NUMBERS TO CORRESPOND TO THOSE IN CONTRACT DOCUMENTS.
<br />PONCHARACTERISTICS TOTHOSE
<br />EIAND
<br />MANUFACTURER ALTHOUGH SEVERAL MAY BE INDICATED AS OFFERING PRODUCTS COMPLYING WITH THE
<br />FLANGES OR INVERTED TEES WITH TILE UNITS FITTING NEATLY AGAINST
<br />2. SHOW PERFORMANCE CAPACITIES.
<br />SECTION 06410 CUSTOM CASEWORK
<br />REQUIREMENTS.
<br />BUTTING SURFACE AND SUPPORT BY WALL ANGLES.
<br />3. SHOW DIMENSIONS AND CLEARANCES REQUIRED.
<br />4. SHOW WIRING OR PIPING DIAGRAMS AND CONTROLS.
<br />PART I CABINETS
<br />B. FURNISH ALL HARDWARE, IN THEIR ORIGINAL PACKAGING, COMPLETE WITH
<br />1.03 METAL SUSPENSION SYSTEM
<br />�
<br />DIVISION 12 FURNISHIN 6
<br />5. DELETE MODEL NUMBERS, DIAGRAMS, DETAILS, ETC., NOT APPLICABLE TO THE
<br />1.01 DOOR FRONTS, DRAWER FRONTS, KICKS AND SPLASHES
<br />ACCESORIES OF PROPER SIZE AND DESIGN REQUIRED FOR THE PURPOSE FOR
<br />A PROVIDE SYSTEM AS MANUFACTURED TO MATCH EXISTING SHALL BE EXPOSED
<br />SUBMITTAL.
<br />A KICKS, SPLASHES AND COUNTER LOPS SHALL BE 3/4" THICK PLYWOOD SURFACED
<br />WHICH THEY ARE TO BE USED AND WITH ALL SCREWS, SHIELDS, AND OTHER
<br />ANCHORAGE DEVICES NECESSARY FOR A COMPLETE INSTALLATION. HARDWARE
<br />TEE -GRID, DOUBLE WEB, INTERMEDIATE DUTY (ASTM C635),
<br />ELECTROGALVANIZED, GOLD -ROLLED STEEL, 15/16 INCHES WIDE, CAPPED
<br />B. MANUFACTURER'S STANDARD SCHEMATIC DRAWINGS AND DIAGRAMS:
<br />I. AND DIAGRAMS TO DELETE INFORMATION WHICH IS NOT
<br />WITH HIGH PRESSURE DECORATIVE PLASTIC LAMINATE ON EXTERIOR FACE AND
<br />SCHEDULE SHOWN ON THE DRAWINGS.
<br />BOTTOM FLANGE. WHITE IN COLOR SYSTEM TO INCLUDE ALL CROSS TEES,
<br />NONE SPECIFIED
<br />MODIFY DRAWINGS
<br />APPLICABLE TO THE WORK
<br />EDGES.
<br />C. INSTALL EACH HARDWARE ITEM IN COMPLIANCE WITH THE NATIONAL BUILDERS
<br />BRIDGING TREES, INTERSECTION CLIPS, SPLICES, COMPLETE EXPOSED GRID
<br />2. SUPPLEMENT STANDARD INFORMATION TO PROVIDE INFORMATION SPECIFICALLY
<br />B. DOOR FRONTS, DRAWER FRONTS AND CABINET BODIES SHALL BE 5/8" BLACK
<br />HARDWARE ASSOCIATION AND THE MANUFACTURER'S INSTRUCTIONS AND
<br />SYSTEM
<br />APPLICABLE TO THE WORK
<br />MELAMINE WITH HIGH PRESSURE DECORATIVE PLASTIC LAMINATE ON EXTERIOR
<br />RECOMMENDATIONS. WHEREVER CUTTING AND FITTING IS REQUIRED TO INSTALL
<br />B, LAY OUT PATTERN IN ACCORDANCE WITH THE DRAWINGS, LEVEL, TRUE TO
<br />1�5 SAMPLES
<br />FACES AND EDGES.
<br />C. STYLE SHALL FLUSH OVERLAY WITH SQUARE EDGES.
<br />HARDWARE ONTO OR INTO SURFACES WHICH ARE LATER TO BE PAINTED OR
<br />FINISHED IN ANOTHER WAY, COORDINATED REMOVAL, STORAGE, AND
<br />PLANE AND AT THE REQUIRED ELEVATION. FRAME AROUND ALL OPENINGS IN
<br />/�
<br />DIVISION 13 SPECIAL CONSTRUC ION
<br />BE
<br />CEILING LIGHTS AND GRILLES WITH MAIN RUNNERS. HANGERS ARE TO BE
<br />1t
<br />A OFFICE SAMPLES SHALL BE OF SIZE INDICATED, OR OF SUPPiCiENt SIZE AND
<br />102 CABINET BACKS
<br />REINSTALLATION OR APPLICATION OF SURFACE PROTECTIONS WITH FINISHING WORK
<br />SPACED At 4'-0" ON CENTER MAXIMUM. PROVIDE ADDITIONAL HANGERS AS
<br />QUANTITY TO CLEARLY ILLUSTRATE:
<br />A 5/8" BLACK MELAMINE BOXES ON BASE AND UPPERS. FINISH INTERIOR FACE TO
<br />D. SET UNITS LEVEL PLUMB AND TRUE TO LINE AND LOCATION. ADJUST AND
<br />REQUIRED TO SUPPORT LIGHT FIXTURES AND HVAC REGISTERS AND GRILLES
<br />I. FUNCTIONAL CHARACTERISTICS OF THE PRODUCT, WITH INTEGRALLY RELATED
<br />MATCH CABINET INTERIOR.
<br />REINFORCE THE ATTACHMENT SUBSTRATE AS NECESSARY FOR PROPER
<br />AND INTERFERENCES OF DUCT WORK
<br />NOW SPECIFIED
<br />PARTS AND ATTACHMENT DEVICES AND TECHNIQUES.
<br />1.03 DRAWERS
<br />INSTALLATION AND OPERATION. DRILL AND COUNTERSINK UNITS NOT FACTORY
<br />a SECURES WIRES BY LOOPING AND WIRE -TYING, EITHER DIRECTLY TO
<br />2. FULL RANGE OF COLOR, TEXTURE AND PATTERN FOR ARCHITECT SELECTION AT
<br />PREPARED FOR ANCHORAGE FASTENERS. SPACE FASTENERS AND ANCHORS IN
<br />STRUCTURES OR TO INSERTS, EYE SCREWS, OR OTHER DEVICES
<br />NO ADDITIONAL COST. SUBMIT ONLY SPECIFIED COLOR RANGE IF DIFFERENT
<br />A DRAWER FRAMES SHALL BE GRASS ZARGEN DRAWER SLIDE SYSTEM OR
<br />ACCORDANCE WITH INDUSTRY STANDARDS. SET THRESHOLDS FOR EXTERIOR
<br />APPROPRIATE FOR SUBSTRATE. SCREW ATTACH EDGE MOLDINGS TO
<br />FROM MANUFACTURER'S STANDARD RANGE.
<br />EQUIVALENT. ALL EXPOSED VIEW PORTIONS SHALL BE FINISHED TO MATCH
<br />DOORS IN FULL BED OF BUTYL -RUBBER OF POLYIOSBUTYLENE MASTIC SEALANT.
<br />SUBSTRATE AT INTERVALS NOT OVER 16 INCHES ON CENTER AND NOT MORE
<br />B. ALL SAMPLES OF A PARTICULAR PRODUCT, ASSEMBLY, UNIT, ETC., SHALL BE
<br />INTERIOR OF CABINET BODIES.
<br />E ADJUST AND CHECK EACH OPERATING ITEM OF HARDWARE AND EACH DOOR TO
<br />THAN 3 INCHES FROM ENDS. LEVEL GRID TO A TOLERANCE OF 1/S" IN 12 FEET.
<br />DIVISION 14 CONVEYING SYSTEMS
<br />SUBMITTED At THE SAME TIME TO ALLOW PROPER REVIEW AND COMPARISON
<br />1.04 SHELVES, DIVIDERS, AND BOTTOMS
<br />ENSURE PROPER OPERATION. REPLACE UNITS THAT CANNOT BE ADJUSTED TO
<br />END OF SECTION 09511
<br />BETWEEN SAMPLES.
<br />A SHELVES ON THE INTERIOR OF CABINETS (BEHIND DOORS), BOTTOM IN CABINET,
<br />OPERATE FREELY AND SMOOTHLY AS INTENDED FOR THE APPLICATION MADE.
<br />1.06 SUBMITTALS
<br />AND VERTICAL DIVIDERS SHALL BE 5/8" WHITE MELAMINE. EXPOSED FACES SHALL
<br />INSTRUCT OWNERS IN PROPER ADJUSTMENT AND MAINTENANCE OF HARDWARE
<br />A PERMITS, LICENSES, AND CERTIFICATES: FOR THE OWNER'S RECORDS, SUBMIT
<br />MATCH CABINET BODY INTERIOR FINISH, ALL EXPOSED FRONT EDGES, INCLUDING
<br />DURING FINAL ADJUSTMENT.
<br />SECTION 0M80 CARPETNG
<br />NONE SPECIFIED
<br />COPIES OF PERMITS, LICENSES, CERTIFICATIONS, INSPECTION REPORTS, RELEASES,
<br />SHELF EDGES, SHALL BE FINISHED WITH ONE (1) TAPED FRONT EDGE.
<br />1.02 KEYING
<br />PART 1 GENERAL
<br />JURISDICTIONAL SETTLEMENTS, NOTICES, RECEIPTS FOR FEE PAYMENTS,
<br />1.05 PLASTIC LAMINATE
<br />A KEYING SHALL BE PER THE OWNERS REQUIREMENTS. TAG KEYS AND PROVIDE
<br />1.01 SUMMARY
<br />`' /�'
<br />DIVISION ISION �S M CN IC/�i.
<br />JUDGMENTS, AND SIMILAR DOCUMENTS, CORRESPONDENCE AND RECORDS
<br />ESTABLISHED IN CONJUNCTION WITH COMPLIANCE WITH STANDARDS AND
<br />��
<br />A 1/16 THICK MATERIAL ON HORIZONTAL SURFACES AND 1/32 ON VERTICAL SURFACES
<br />(GENERAL NOTE: ALL EXTERIOR CORNERS OF COUNTER TOPS TO HAVE A RADIUS
<br />TO OWNER AT SUBSTANTIAL COMPLETION.
<br />A PROVIDE TYPE AND STYLE AS SCHEDULED IN THE FINISH MATERIAL SCHEDULE.
<br />REGULATIONS BEARING UPON PERFORMANCE OF THE WORK
<br />OF 1 I/2")
<br />B. ADHESIVES.
<br />1.01 CONTRACTOR RESPONSIBILITIES
<br />PART 2 PRODUCTS
<br />1.03 GUARANTEE
<br />A PROVIDE ONE-YEAR GUARANTEE FOR ALL HARDWARE. PERIOD OF GUARANTEE
<br />I. PROVIDE WHITE LATEX CARPET ADHESIVE SUCH AS W.W. HENRY
<br />A REVIEW SHOP DRAWINGS, PRODUCT DATA AND SAMPLES PRIOR TO SUBMISSION.
<br />2ldl HARDWARE
<br />SHALL BEGIN FROM DATE OF OWNERS ACCEPTANCE.
<br />COMPANY NO 356, ROBERTS COMPANY NO. 41-0504, OR AN EQUAL
<br />APPROVED BY THE ARCHITECT AND RECOMMENDED FOR THE
<br />B. DETERMINE AND VERIFY:
<br />A HINGES: "GRASS 120 DEGREE SNAP -ON 3,000 SERIES" FULL OVERLAY SELF CLOSING
<br />PURPOSE BY THE MANUFACTURER OF THE SELECTED CARPET.
<br />SEE �Ci-iANICAL
<br />L FIELD MEASUREMENTS.
<br />B. PULLS: 3" BRUSHED ALUMINUM FINISH BY STANLEY OR EQUAL FINAL SELECTION TBD
<br />END OF SECTION 08110
<br />2. FIELD CONSTRUCTION CRITERIA.
<br />C. DRAWER GLIDES: SEE SPECIFICATION ABOVE
<br />2. PROVIDE SEAM ADHESIVE SUCH AS W.W. HENRY COMPANY NO. 246,
<br />3. CATALOG NUMBERS AND SIMILAR DATA.
<br />D. LOCK: NATIONAL LOCK "123-26D (DOOR), "-9136-26D (DRAWER.
<br />ROBERTS COMPANY NO. 41-0502, OR AN EQUAL APPROVED BY THE
<br />Q
<br />DIVISION 9 INISI�ES
<br />4. CONFORMANCE WITH SPECIFICATIONS AND DRAWINGS.
<br />C. COORDINATE EACH SUBMITTAL WITH REQUIREMENTS OF THE WORK AND THE
<br />E. KEYBOARD DRAWER: AGCURIDE CBER30 - TRAY 200 KEYBOARD SYSTEM BY ACCURIDE
<br />ARCHITECT AND RECOMMENDED FOR THE PURPOSE BY THE
<br />MANUFACTURER OF THE SELECTED CARPET.
<br />DIVISION �� ELECTRICAL
<br />CONTRACT DOCUMENTS. DO NOT SUBMIT NON -CONFORMING PRODUCTS.
<br />PART 3 INSTALLATION
<br />C. AT INTERSECTION OF CARPET AND FLOOR TILE, PROVIDE ROPPE COMPANY, INC.
<br />D NOTIFY THE ARCHITECT IN WRITING, AT THE TIME OF SUBMISSION, OF ANY DEVIATIONS
<br />3.01 INSTALLATION
<br />VINYL TILE CARPET JOINER PISS OR EQUIVALENT.
<br />IN THE SUBMITTALS FROM REQUIREMENTS OF THE CONTRACT DOCUMENTS, OR OF ANY
<br />DISCREPANCIES WITHIN THE CONTRACT DOCUMENTS.
<br />A PROVIDE WOOD BACK BLOCKING AT PROPER LOCATIONS IN PARTITIONS FOR
<br />SECTION 09110 METAL SYSTEMS
<br />D. PROVIDE OTHER MATERIALS, NOT SPECIFICALLY DESCRIBED BUT REQUIRED FOR
<br />SEE ELECTRICAL
<br />E. BEGIN NO FABRICATION OR WORK WHICH REQUIRES SUBMITTALS UNTIL RETURN OF
<br />CASEWORK ATTACHMENT.
<br />METAL STUDS
<br />A COMPLETE AND PROPER INSTALLATION, AS SELECTED BY THE CONTRACTOR,
<br />SUBMITTALS WITH ARCHITECT'S CONFORMANCE REVIEW.
<br />END OF SECTION 06410
<br />SUBJECT TO THE APPROVAL OF THE ARCHITECT.
<br />/� SPECIFICATIONS
<br />OF
<br />F. SUBMITTALS NOT PROPERLY REVIEWED BY CONTRACTOR FOR CONFORMANCE WITH
<br />CONTRACT DOCUMENTS SHALL BE RETURNED WITHOUT ARCHITECT'S REVIEW OR
<br />A AT INTERIOR METAL STUD PARTITIONS, UNLESS OTHERWISE SHOWN ON THE
<br />DRAWINGS, PROVIDE STANDARD PUNCH STEEL STUDS OF THE SIZES
<br />E. ALLOW THE OWNER TO INSPECT AND SELECT FROM SCRAP CARPET REMAINING
<br />AFTER THE INSTALLATION. WRAP IN AND
<br />DIVISION I T�-IERMAL AND MOISTURE
<br />BUNDLE, BURLAP, DELIVER TO THE
<br />ACCEPTANCE.
<br />SHOWN ON THE DRAWINGS, EITHER NOT -DIP GALVANIZED OR FACTORY
<br />OWNER THE CARPET SCRAPS SO SELECTED.
<br />IDS SUBMISSION REQUIREMENTS
<br />CTION
<br />PRE -PAINT: 25 GA. UNLESS SHOWN OTHERWISE ON THE DRAWINGS. 20
<br />END OF SECTION 09680
<br />GA. AT ALL DOOR OPENINGS.
<br />A MAKE SUBMITTALS PROMPTLY IN ACCORDANCE WITH APPROVED SCHEDULE, AND IN
<br />SUCH SEQUENCE AS TO CAUSE NO DELAY IN THE WORK OR IN THE WORK OF ANY
<br />SECTION "I0 BUILDM INSULATION
<br />B. ACCESSORIES: PROVIDE ALL ACCESSORIES INCLUDING, BUT NOT
<br />SECTION 090" PAINTING
<br />OTHER CONTRACTOR
<br />PART I GENERAL
<br />NECESSARILY LIMITED TO, TRACKS, CLIPS, ANCHORS, FASTENING
<br />DEVICES, SOUND ATTENUATION PENCIL RODS AND RESILIENT CLIPS, AND
<br />PART I GENERAL
<br />B. NUMBER OF SUBMITTALS REQUIRED:
<br />1.02 GENERAL BUILDING INSULATION
<br />OTHER ACCESSORIES REQUIRED FOR A COMPLETE AND PROPER
<br />I. SHOP DRAWINGS: SUBMIT THE NUMBER OF OPAQUE REPRODUCTIONS WHICH THE
<br />A BLANKET INSULATION TO BE UNPAGED, MINERAL FIBER WITH THERMOSETTING RESINS,
<br />INSTALLATION, AND AS RECOMMENDED BY THE MANUFACTURER OF THE
<br />STEEL STUDS USED.
<br />I.01 GENERAL
<br />A It IS THE INTENT OF THIS SPECIFICATION TO PRODUCE A PREMIUM JOB, WHICH WILL
<br />CONTRACTOR REQUIRES, PLUS THREE (3) COPIES WHICH WILL BE RETAINED BY
<br />TYPE 1. MINERAL FIBER SHALL BE MANUFACTURED FROM GLASS.
<br />PROVIDE THE MAXIMUM DURABILITY, WHICH CAN REASONABLY BE EXPECTED F RO
<br />THE ARCHITECT. MAXIMUM ACCEPTABLE SIZE IS 24" x 36" FOR ANY ONE SHEET.
<br />G. MEET OR EXCEED MINIMUM REQUIREMENTS OF FEDERAL SPEC.
<br />A PAINTED SURFACE.
<br />2. PRODUCT DATA: SUBMIT THE NUMBER OF COPIES WHICH THE CONTRACTOR
<br />B. INSTALL INSULATION UNITS COMPLYING WITH MANUFACTURER'S RECOMMENDATIONS.
<br />QQ-S-698 AND FEDERAL SPEC. QQ-S-1-15D, GLASS D.
<br />REQUIRES, PLUS THREE (3) WHICH WILL BE RETAINED BY THE ARCHITECT.
<br />INSTALL BLANKET INSULATION IN STUD WALLS. BOND UNITS TO SUBSTRATE WITH
<br />B. "PAINT" INCLUDES COATING SYSTEMS MATERIALS, PRIMERS, EMULSIONS, ENAMELS,
<br />3. SAMPLES: SUBMIT THE NUMBER STATED IN EACH SPECIFICATION SECTION. IF NO
<br />ADHESIVE OR USE MECHANICAL ANCHORAGE TO PROVIDE PERMANENT PLACEMENT.
<br />METAL TRIM
<br />STAINS, SEALERS, AND FILLERS, AND OTHER APPLIED MATERIALS WHETHER USED
<br />NUMBER IS GIVEN, VERIFY CORRECT NUMBER WITH ARCHITECT PRIOR TO
<br />1.03 SOUND ATTENUATING INSULATION
<br />A FORM FROM GALVANIZED STEEL NOT LIGHTER THAN 26 GAUGE,
<br />AS PRIME, INTERMEDIATE, OR FINISH COAT.
<br />SUBMITTAL. MINIMUM OF TWO (2) SAMPLES.
<br />4. PROVIDE SUBMITTALS AS REQUIRED BY THE INDIVIDUAL SECTION, BUT NO LESS
<br />A SOUND INSULATION SHALL BE AS MANUFACTURED BY OWENS-CORNING FIBERGLASS,
<br />COMPLYING WITH FEDERAL SPEC QQ-5-1-15, CLASS D.
<br />C. SPECIFIED PRODUCTS BELOW ARE MANUFACTURED BY SHERWIN WILLIAMS, EXCEPT
<br />THAN THAT STATED ABOVE.
<br />FIBERGLASS NOISE BARRIER BATTS. INSTALL IN STUD WALLS AND CEILINGS WHERE
<br />B. CASING BEADS: U.S.G.0200-B.
<br />WHERE OTHER MANUFACTURERS ARE INDICATED, AND ESTABLISH A STANDARD OF
<br />QUALITY. EQUIVALENT PRODUCTS OF OTHER ACCEPTABLE MANUFACTURERS MAY
<br />INDICATED ON THE DRAWINGS. FIT INSULATION TIGHTLY BETWEEN STUD MEMBERS.
<br />C. SUBMITTALS SHALL CONTAIN:
<br />NOT BE USED UNLESS APPROVED BY ARCHITECT.
<br />I. THE DATE OF SUBMISSION AND THE DATES OF ANY PREVIOUS SUBMISSIONS.
<br />END OF SECTION O'1210
<br />END OF SECTION 09110
<br />D. PROVIDE BEST GRADE AND QUALITY MATERIALS AND PRODUCTS MANUFACTURED
<br />2. THE PROJECT TITLE AND NUMBER
<br />SECTION 01900 JOINT SEALERS
<br />BY SHERWIN WILLIAMS. MATCH COLORS AS INDICATED ON THE DRAWINGS. USE
<br />3. CONTRACT IDENTIFICATION.
<br />PART, I GENERAL
<br />SECTION OW50 GYPSUM WALLBOARD
<br />PREMIXED PAINTS INSOFAR AS POSSIBLE. THIN ONLY AS PERMITTED ANY
<br />4. THE NAMES OF:
<br />MANUFACTURER'S LABEL INSTRUCTIONS, AND AVOID UNNECESSARY THINNING.
<br />a. CONTRACTOR
<br />1.01 GENERAL
<br />PART I GENERAL
<br />b. SUBCONTRACTOR
<br />A PROVIDE JOINT SEALERS, JOINT FILLERS, AND OTHER RELATED MATERIALS THAT
<br />E. PROTECT FINISHED SURFACES, WORK OF OTHER TRADES, AND PROPERTY UP THE
<br />OWNER FROM DAMAGE AND DEFACEMENT. COVER FLOORS AND FIXED EQUIPMENT
<br />a
<br />a SUPPLIER
<br />ARE COMPATIBLE WITH ONE ANOTHER AND WITH JOINT SUBSTRATES UNDER
<br />1O1 ��
<br />WITH DROP CLOTHS.
<br />MANUFACTURER
<br />CONDITIONS OF SERVICE AND APPLICATION, AS DEMONSTRATED BY SEALANT
<br />A GYPSUM WALLBOARD WORK SHALL CONFORM TO THE GYPSUM ASSOCIATION
<br />5 . IDENTIFICATION OF THE PRODUCT, WITH THE SPECIFICATION SECTION NUMBER
<br />5NUFACTURER
<br />BASED AND FIELD EXPERIENCE. PROVIDE COLORS TO
<br />RECOMMENDED SPECIFICATIONS FOR THE APPLICATION AND FINISHING OF
<br />F. PREPARE SURFACES ACCORDING TO PAINT MANUFACTURER'S INSTRUCTIONS.
<br />. FIELD DIMENSIONS, CLEARLY IDENTIFIED AS SUCH.
<br />MAF NSH SURFACES.
<br />GYPSUM WALLBOARD.
<br />EXAMINE FACTORY FINISHED AND PRIMED SURFACES t0 BE PAINTED, AND VERIFY
<br />1. RELATION TO ADJACENT OR CRITICAL FEATURES OF THE WORK OR MATERIALS.
<br />COMPATIBILITY OF EXISTING MATERIAL WITH PAINT TO BE APPLIED. APPLY PAINT
<br />8. APPLICABLE STANDARDS SUCH AS, BUT NOT LIMITED TO ASTM OR FEDERAL
<br />B. PROVIDE SEALANT BACKINGS OF MATERIAL AND TYPE WHICH ARE NONSTAINING,
<br />B. EXAMINE SUBSTRATES TO WHICH DRY WALL CONSTRUCTION ATTACHES OR
<br />IN STRICT ACCORDANCE WITH THE MANUFACTURER'S PRINTED INSTRUCTIONS ONLY
<br />SPECIFICATION NUMBERS.
<br />ARE COMPATIBLE WITH JOINT SUBSTRATE, SEALANTS, PRIMERS, AND OTHER FILLERS,
<br />gBUTTS, PRESET HOLLOW METAL FRAMES, CAST-IN-ANCORS, AND STRUCTURAL
<br />TO SURFACES WHICH ARE THOROUGHLY DRY, SMOOTH, EVEN, GLEAN, FREE OF DUST
<br />11 IDENTIFICATION OF DEVIATIONS FROM CONTRACT DOCUMENTS.
<br />AND ARE APPROVED FOR APPLICATIONS INDICATED BY SEALANT MANUFACTURER
<br />FRAMING FOR COMPLIANCE WITH REQUIREMENTS FOR INSTALLATION TOLERANCE
<br />AND PROPERLY PREPARED TO RECEIVE THE INTENDED FINISH.
<br />10. IDENTIFICATION OF OPTIONS AVAILABLE, BUT NOT INDICATED IN THE
<br />a SEALANTS: SEALANTS SHALL BE AS FOLLOWS OR EQUAL:
<br />AND OTHER CONDITIONS AFFECTING PERFORMANCE OF DRY WALL
<br />1.02 PAINTING
<br />SPECIFICATIONS, SUCH AS COLOR, FINISH, TEXTURE, ETC. WITH COMPLETE SAMPLES
<br />1. ONE -PART POLYURETHANE:
<br />CONSTRUCTION. DO NOT PROCEED WITH INSTALLATION UNTIL UNSATISFACTORY
<br />OR LISTING INCLUDED IN THE SUBMITTAL FOR ARCHITECT'S SELECTION.
<br />2. TWO-PART POLYURETHANE:
<br />CONDITIONS HAVE BEEN CORRECTED.
<br />A ACCEPTABLE MATERIALS
<br />11. INDICATION OF TERMS TO BE INCLUDED IN THE WORK AND SHOWN ON THE SHOP
<br />3. SILICONE:
<br />G. DO NOT CAPE AND FINISH GYPSUM BOARD WHEN THE TEMPERATURE IS BELOW 60
<br />L ALL PAINTING TO BE SCHEDULED IN THE FINISH SCHEDULE.
<br />DRAWINGS SHALL BE DIMENSIONED AND COORDINATED FOR PROPER FIT AND
<br />D. COMPLY WITH JOINT SEALER MANUFACTURER'S PRINTED INSTALLATION INSTRUCTION
<br />DEGREES FAHRENHEIT. THE TEMPERATURE OF THE ROOMS SHALL BE HELD AT
<br />2. EQUIVALENT PRODUCTS OF THE FOLLOWING ARE ALSO ACCEPTABLE:
<br />TIMELY INCLUSION.
<br />APPLICABLE TO PRODUCTS AND APPLICATIONS INDICATED. CLEAN OUT JOINTS
<br />60 DEGREES FAHRENHEIT FOR 45 HOURS BEFORE TAPING AND FINISHING IS TO
<br />PRATT t LANBERTT
<br />12. ID
<br />IDENTIFICATION OF REVISIONS ON SUBMITTALS.
<br />IMMEDIATELY BEFORE INSTALLING JOINT SEALERS. PRIME WHERE RECOMMENDED B
<br />BEGIN. MAINTAIN 60 DEGREES FAHRENHEIT DURING AND AFTER INSTALLATION.-
<br />GLIDDEN
<br />13. 8" x 3" BLANK SPACE FOR CONTRACTOR AND ARCHITECT SCAMPS. -
<br />SEALER MANUFACTURER DO NOT ALLOW MIGRATION OF PRIMER ONTO ADJACENT
<br />VENTILATES AS -REQUIRED TO REMOVE: EXCESS HUMIDITY.-
<br />PORT`ER
<br />- -
<br />14. CONTRACTOR'S STAMPS, INITIALED OR SIGN, CERTIFYING THE REVIEW OF
<br />SURFACES. MASK WHERE REQUIRED TO PROTECT ADJOINING SURFACES FOR STAININ
<br />BENJAMINE MOORE
<br />SUBMITTAL, VERIFICATION OF PRODUCTS, FIELD MEASUREMENTS AND FIELD
<br />OR DAMAGE BY CLEANING METHODS TO REMOVE SMEARS.
<br />1.02 GYPSUM WALLBOARD
<br />CONSTRUCTION CRITERIA, AND COORDINATION OF: THE INFORMATION WITHIN THE
<br />A GYPSUM WALLBOARD SHALL BE MANUFACTURED BY U.S. GYPSUM. WALLBOARD IS
<br />B. UNDERCOATS AND THINNERS
<br />SUBMITTAL WITH REQUIREMENTS OF THE WORK AND OF CONTRACT DOCUMENTS.
<br />E. APPLY SEALANTS IN A MANNER SO THAT APPEARANCE IS THAT OF A SMOOTH,
<br />TO MEET. ASTMI C36-84A AND 85-L-30d 1/2 INCHES THICK, 48 INCHES WIDE WITH
<br />L PROVIDE UNDERCOAT PAINT PRODUCED BY THE SAME MANUFACTURER OF
<br />UNIFORM, SLIGHTLY CONCAVE BEAD. TOOL WITH CAULKING TOOL AS REQUIRED WITHI
<br />TAPERED EDGES.
<br />FINISH COAT.
<br />IDS RESUBMISSION REQUIREMENTS
<br />10 MINUTES OF APPLICATION. ALL SEALED JOINTS ARE TO BE WATER -TIGHT.
<br />A MAKE ANY CORRECTIONS OR CHANGES IN THE SUBMITTALS REQUIRED BY THE
<br />F. BACKER ROD: POLYETHYLENE FOAM BACKER ROD, NONSTAINING,
<br />B. AT FIRE RATED PARTITIONS INSTALL WALLBOARD TO MEET SEPARATE
<br />2. USE ONLY THINNERS RECOMMENDED BY THE PAINT MANUFACTURER AND USE
<br />ONLY THE RECOMMENDED LIMITS.
<br />ARCHITECT AND RESUBMIT UNTIL ACCEPTED.
<br />CHEMICLOSCAL E HLFO
<br />EXPANDED POLYETHYLENE FOAM AS MANUFACTURED BY DOW CHEMICAL ETHLFOAM
<br />REQUIREMENTS, USE TYPE III, GRADE X CLASS 1, 5/8 INCHES THICK FIRE
<br />B. SHOP DRAWINGS AND PRODUCT DATA:
<br />FURNISH WITH ROUND EDGE IN THICKNESS REQUIRED.
<br />. RETARDANT WALLBOARD
<br />G. COLOR SCHEDULES
<br />L REVISE INITIAL DRAWINGS OR DATA, AND RESUBMIT AS SPECIFIED FOR THE
<br />END OF SECTION 0i900
<br />C. INSTALL GYPSUM BOARD WITH TRUE, EVEN SURFACES AND STRAIGHT, SHARP
<br />L PROVIDE PAINTING AS SCHEDULED IN THE FINISH MATERIALS SCHEDULE.
<br />INITIAL SUBMITTAL.
<br />CORNERS. USE FULL LENGTH BOARDS WHERE POSSIBLE. END JOINTS ON THE
<br />a. ON GYPSUM DRYWALL, USE:
<br />2. INDICATE ANY CHANGES WHICH HAVE BEEN MADE OTHER THAN THOSE
<br />SAME SIDE OF A WALL SHALL BE STAGGERED AND JOINTS ON OPPOSITE SIDE
<br />REQUESTED BY THE ARCHITECT.
<br />C. SAMPLES: SUBMIT NEW SAMPLES AS REQUIRED FOR INITIAL SUBMITTAL.
<br />Q �Q /� �y� �Q
<br />DIVISION S DOORS WINDOWS
<br />SHALL NOT OCCUR OVER THE SAME SUPPORT. DO NOT LOCATE NORMAL END
<br />L FIRST COAT - PIGMENTED PRIMER/SEALER
<br />2. SECOND COAT - ACRYLIC LATEX ENAMEL
<br />FIND
<br />JOINTS AT EDGE OF OPENINGS. FORM JOINTS NEATLY. BUTT BOARDS TOGETHER
<br />BUT DO NOT FORGE INTO PLACE. DO NOT BUTT EDGES AGAINST TAPERED
<br />3. THIRD COAT - ACRYLIC LATEX ENAMEL
<br />1.10 DISTRIBUTION
<br />A DISTRIBUTE REPRODUCTION OF SHOP DRAWINGS AND COPIES OF PRODUCT DATA
<br />EDGES. NO JOINT SHALL HAVE A GAP GREATER THAN 1/4 INCH.
<br />b. ON FERROUS METAL, USE:
<br />L FIRST COAT -TRUST INHIBITIVE ALKYD METAL PRIMER
<br />SECTION M211 FLUSH WOOD DOORS
<br />WHICH CARRY THE ARCHITECT'S STAMP OF CONFORMANCE TO:
<br />PART (GENERAL
<br />D. IN GENERAL, INSTALL GYPSUM BOARD ON CEILING BEFORE WALLS. CONSTRUCT
<br />2. SECOND GOAL - SEMI -GLOSS ALKYD ENAMEL
<br />L JOB SITE FILE.
<br />CEILINGS WITH LONG DIMENSION OF GYPSUM BOARD APPLIED At RIGHT ANGLES
<br />3. THIRD GOAL -SEMI-GLLOSSOSS ALKYD
<br />LKYD ENAMEL
<br />2. RECORD DOCUMENTS FILE.
<br />1.01 GENERAL
<br />TO SUPPORT.
<br />3. SUBCONTRACTORS.
<br />A DO NOT DELIVER DOORS OR INSTALL UNTIL CONDITIONS FOR TEMPERATURE AND
<br />RELATIVE HUMIDITY HAVE BEEN STABILIZED AND WILL BE MAINTAINED IN STORAGE
<br />E. SCREW GYPSUM BOARD TO FRAMING WITH SCREWS NOT OVER S INCHES ON CENTER
<br />a ON WOOD DOORS, USE:
<br />4. SUPPLIER OR FABRICATOR
<br />5. OWNER (TO BE DISTRIBUTED BY THE ARCHITECT).
<br />AND INSTALLATION AREAS DURING REMAINDER OF CONSTRUCTION PERIOD.
<br />FASTEN GYPSUM BOARD BEGINNING At THE CENTER AND WORK TOWARDS OUTER
<br />EDGES. HOLD BOARD FIRMLY AGAINST WOOD FRAMING WHILE FASTENING.
<br />L FIRST GOAT - STAIN (SEE FINISH SCHEDULE)
<br />2. SECOND COAT - STAIN (SEE FINISH SCHEDULE)
<br />1.02 INTERIOR FLUSH WOOD SOLID GORE DOORS
<br />FASTENERS AT EDGES OF BOARDS SHALL BE 1/2 INCH FROM THE EDGE.
<br />3. THIRD GOAT - VARNISH LOW SHEEN "RUBBED EFFECT"
<br />1.11 ARCHITECT'S DUTIES
<br />5 OR 7 PLY, PARTICLE BOARD GORE, CONFORMING TO AWI
<br />A PROVIDE DOORS 1 3/4„
<br />A REVIEW SUBMITTALS WITH REASONABLE PROMPTNESS AND IN ACCORD WITH
<br />,
<br />SECTION 1300 FACE VENEER SHALL BE PREMIUM STAIN GRADE BIRCH. EDGE
<br />F. OPENINGS FOR ELECTRICAL DEVICES, PIPING, GRILLS, AND REGISTERS SHALL BE
<br />END OF SECTION 09900
<br />SCHEDULE. ALLOW A MINIMUM OF TEN (10) WORKING DAYS FOR REVIEW, UNLESS
<br />STRIPS SHALL BE HARDWOOD. STILE EDGE SHALL NOT BE LESS THAN 2 3/8" THICK
<br />ACCURATELY LOCATED AND NEATLY MADE TO CLOSELY FIT THE DEVICES AND
<br />SPECIAL HANDLING IS ARRANGED IN ADVANCE.
<br />EDGE BEFORE TRIMMING AND SHALL BE SPECIES COMPATIBLE WITH FACE VENEE
<br />BE COMPLETELY COVERED BY PLATES AND ESCUTCHEONS.
<br />B. AFFIX STAMP AND INITIALS OR SIGNATURE, AND INDICATE REQUIREMENTS FOR
<br />TOP AND BOTTOM AND BOTTOM EDGE SHALL NOT BE LESS THAN 1 1/8" BEFORE
<br />103 TRIM PIECES
<br />RESUBMITTAL OR CONFORMANCE OF SUBMITTAL. ACCEPTANCE IS FOR GENERAL
<br />TRIMMING.
<br />A PROVIDE TRIM ACCESSORIES OF THE SIZES REQUIRED FOR THE WALLBOARD
<br />CONFORMANCE WITH DESIGN CONCEPT AND GENERAL COMPLIANCE WITH THE
<br />CONTRACT DOCUMENTS. QUANTITIES AND DIMENSIONS OF MATERIALS WILL NOT BE
<br />APPLICATION AS MANUFACTURED BY U.S. GYPSUM. PROVIDE DUR-A-BEAD
<br />REVIEWED. ACCEPTANCE OF A SUBMITTAL DOES NOT WAIVE OR ALTER THE
<br />CORNER BEAD AT EXTERNAL CORNERS AND NO. 200-A METAL CASING BEAD
<br />REQUIREMENTS OF THE CONTRACT DOCUMENTS.
<br />WHERE WALLBOARD ABUTTS OTHER MATERIALS.
<br />C. RETURN SUBMITTALS TO CONTRACTOR FOR DISTRIBUTION OR FOR RESUBMISSION.
<br />1.04 FASTENERS
<br />A PROVIDE SCREWS, NAILS, CLIPS, TIES, AND OTHER FASTENERS AS RECOMMENDED
<br />END OF SECTION 01340
<br />BY THE GYPSUM MANUFACTURER
<br />REVISIONS
<br />BY
<br />u
<br />�UU o
<br />y M N
<br />L Cz.
<br />4 0
<br />�
<br />yx�
<br />E
<br />rom
<br />/� /
<br />N
<br />O
<br />•--� C1. U
<br />O
<br />O
<br />,nN
<br />U '::.
<br />Lo
<br />o
<br />-' 00 3
<br />Y 3:- 3
<br />x N
<br />c
<br />0
<br />�tiaL.
<br />m
<br />I
<br />I
<br />a
<br />�v
<br />co
<br />�`
<br />•C
<br />.y
<br />9�
<br />L
<br />OM
<br />,Chi.
<br />G�
<br />a� co
<br />O
<br />C0
<br />0
<br />C2
<br />a�
<br />O
<br />U
<br />Z_
<br />O
<br />'m
<br />J
<br />N
<br />It
<br />C
<br />U
<br />m
<br />v
<br />a
<br />v M
<br />W
<br />Q
<br />N O
<br />O
<br />U
<br />O
<br />Q
<br />LL1
<br />v
<br />N
<br />O
<br />'a
<br />Lo •_
<br />M i
<br />Q
<br />C)
<br />C)o -C
<br />O
<br />M a-
<br />CL
<br />OL.
<br />N
<br />N
<br />I
<br />0
<br />J
<br />Date:
<br />06.
<br />03. 16
<br />Scale:
<br />AS
<br />NOTED
<br />Project Mgr: AAY
<br />Drawn: JDS
<br />Job:
<br />16-062
<br />Sheet
<br />N1
<br />
|