|
WEATHER
<br />7 RESISTIVE
<br />BARRIER
<br />TAPE
<br />(ASSEMBLEDWIND )
<br />HEAD FLASHING TIE-IN INSTRUXTIONS
<br />1. Cut, fold up & temporarily secure weal
<br />THESE DETAILS ARE GENERIC AND barrier above header to allow for flashing
<br />installation
<br />MEANT TO SHOW GENERAL FLASHING 2. Self -adhered flashing plus head flashing under
<br />AND WATERPROOFING METHODS TO weather resistive barrier
<br />BE USED. 3. Fold weather resistive barrier back over head
<br />flashing and seal with tape
<br />SELF -ADHERED FLASHING Scale: NTS
<br />FLANGED WINDOW
<br />FLASHING INSTALLATION AFTER WEATHER RESISTIVE BARRIER
<br />DO NO"
<br />BOTTO
<br />FLANGE
<br />SELF -ADHERED FLASHING
<br />HALF ROUND WINDOW
<br />SELF -ADHERED FLASHING
<br />DECK JOIST
<br />SELF -ADHERED FLASHING
<br />PRODUCTS DETAILS
<br />TWO LAYERS OF FELT OR ONE LAYER OF HOUSE WRAP AND
<br />ONE LAYER OF FELT ARE REQUIRED BEHIND STUCCO. FBC
<br />R703.2.1 AND FBCR 703.7.3
<br />Detail Instructions
<br />Refer to the number marked as ## in each detail that corresponds to the
<br />numbered items in the list of Instructions below:
<br />1. Install self -adhered flashing in order as shown by numbers
<br />2. Install flashing and weather resistive barrier to form water shedding
<br />laps
<br />3. Self -adhered flashing can be substituted for building paper
<br />4. Split the release paper using the ripcord (Split release on demand,
<br />embedded in the adhesive layer) - for ease of installation and to
<br />minimize scoring cuts
<br />5. Remove all release paper per standard installation instructions and
<br />adhere to substrate using a square piece of flashing material (6" x 6"
<br />Minimum)
<br />6. Fold as shown by arrows
<br />7. Angle of corner may vary, adjust folding of the flashing accordingly to
<br />fit tight to corner
<br />8. Mechanically fasten as necessary
<br />2x FRAMEWALL
<br />TILE FINISH-
<br />1/2" DUROCK-
<br />8" CMU
<br />4"OR8"CMU
<br />(PER SEAT DEPTH)
<br />FILL WITH GROUT -
<br />SLOPED MUD BED -
<br />VINYL SHOWER PAN
<br />4
<br />WEATHER
<br />✓E BARRIER &
<br />(
<br />,ARILY SECURE
<br />WOOD FRAME CONSTR.
<br />EXTERIOR SELF -ADHERED FLASHING
<br />SHEATHING BY LAPPING DOWN
<br />OVER RIM JOIST AND UP
<br />WALL BY 6 IN.
<br />WEATHER
<br />RESISITIVE
<br />BARRIER SEAL TOPS OF JOI;
<br />UNDER DECKING
<br />ED FLASHING (SEE DETAIL WP07)
<br />E�1
<br />4SHING
<br />WEATHER RESISTIVE
<br />BARRIER
<br />DOOR ROUGH OPENING
<br />- 3/4"-1" BEAD OF CONSTR.
<br />ADHESIVE TO BE APPLIED UNDER
<br />THRESHOLD OF DOOR AND RETURN
<br />UP JAMB 6". USE LIQUID NAIL BRAND
<br />OR EQUAL WEATHER PROOF CAULKING
<br />SELF -ADHERED FLASHING
<br />SUBFLOOR
<br />SELF -ADHERED FLASHING
<br />EXTERIOR DOOR WITH DECK - SECTION A
<br />EXTERIOR SHEATHING
<br />3/4"-1" BEAD OF CONSTR.
<br />ADHESIVE TO BE APPLIED UNDER
<br />THRESHOLD OF DOOR AND RETURN
<br />UP JAMB 6". USE LIQUID NAIL BRAND
<br />OR EQUAL WEATHER PROOF CAULKING
<br />SECTION -A (SEE DETAIL
<br />q SELF -ADHERED FLASHING
<br />1
<br />2 SEAL TOPS OF JOISTS
<br />8 UNDER DECKING
<br />(SEE DETAIL WP07)
<br />M
<br />SELF-ADHER
<br />2
<br />1'-4" PER PLAN
<br />T-0" PER PLAN
<br />SHOWER SEAT
<br />31
<br />a
<br />4
<br />SELF -ADHERED FLASHING
<br />EXTERIOR DOOR WITH DECK
<br />SELF -ADHERED FLASHING
<br />OUTSIDE CORNER
<br />RIM JOIST
<br />INSTALL SELF -ADHERED
<br />FLASHING JAMB & HEAD
<br />FLASHING, SEE
<br />FLANGED WINDOW
<br />(SEE DETAIL WP01)
<br />SELF -ADHERED FLASHING,
<br />EXTEND A MINIMUM 6"
<br />VERTICALLY FROM
<br />BOTTOM OF
<br />THRESHOLD
<br />SELF -ADHERED FLASHING
<br />PATCH
<br />iHERED FLASHING
<br />Q Y
<br />W
<br />W
<br />Ca
<br />Q
<br />Z
<br />d
<br />z z - -
<br />g �
<br />LU LU PLASTER STOP
<br />= CL
<br />Ir-
<br />W CONTINUOUS BACKER
<br />U ROD & SEALANT
<br />w W
<br />W
<br />�0 A
<br />U)
<br />8 z
<br />�o
<br />0
<br />0
<br />WINDOW UNIT
<br />FLASHING REQUIREMENTS
<br />SLOPE
<br />0.3 in: 12.0 in
<br />R703.1 General. Exterior walls shall provide the building with a weather -resistant exterior wall envelope. The exterior wall envelope shall include
<br />(0.6 cm ; 30.5 cm)
<br />(0.30
<br />flashing as described in Section R703.4. A water -resistive barrier is described as a material behind an exterior wall covering that is intended to
<br />SELF -ADHERED FLASHING
<br />resist liquid water that has penetrated behind the exterior covering from further intruding into the exterior wall assembly. An exterior wall covering
<br />EXTERIOR
<br />is described as a material or assembly of materials applied on the exterior side of exterior walls for the purpose of providing a weather -resistive
<br />CEMT. FIN.
<br />barrier, insulation, or for aesthetics, including but not limited to, veneers, siding, exterior insulation and finish systems, architectural trim and
<br />BUILDING PAPER
<br />embellishments such as cornices, soffits, and fascias.
<br />WIRE LATH
<br />R703.2 Water -resistive barrier. One layer of No. 15 asphalt felt, free from holes and breaks, complying with ASTM D226 for Type 1 felt or other
<br />approved water -resistive barrier shall be applied over studs or sheathing of all exterior walls. Such felt or material shall be applied horizontally,
<br />with the upper layer lapped over the lower layer not less than 2 inches (51 mm). Where joints occur, felt shall be lapped not less than 6 inches
<br />(152 mm). The felt or other approved material shall be continuous to the top of walls and terminated at penetrations and building appendages in a
<br />manner to meet the requirements of the exterior wall envelope as described in Section R703.1.
<br />R703.7.3 Water -resistive barriers shall be installed as required in Section R703.2 and, where applied over wood -based sheathing, shall include a
<br />water -resistive vapor -permeable barrier with a performance at least equivalent to two layers of Grade D paper. The individual layers shall be
<br />Q
<br />installed independently such that each layer provides a separate continuous plane and any flashing (installed in accordance with Section R703.4)
<br />intended to drain to the water -resistive barrier is directed between the layers.
<br />SELF -ADHERED FLASHING Exception: Where the water -resistive barrier that is applied over wood -based sheathing has a water resistance equal to or greater than
<br />CEMT. FINISH SILL/ POTSHELF/ CHIMNEY SHOULDER / that of 60-minute Grade D paper and is separated from the stucco by an intervening, substantially nonwater-absorbing layer or designed
<br />drainage space.
<br />MECHANICALLY FASTEN IF RUBBERIZED RUBBERIZED ASPHALT
<br />NEEDED IN CORNERS ADHESIVE
<br />ASPHALT ADHESIVE g pp g pp g p entry y
<br />THROUGH SELF -ADHERED R703.4 Flashing. Approved corrosion -resistant flashing shall be applied shingle -fashion in a manner to prevent ent of water into the wall cavity
<br />FLASHING - -eel c_nDHERED FLASHING ----or penetration of water to the building structural framing components Self -adhered membranes used as flashing shall comply with AAMA 711. All
<br />Fez
<br />d
<br />00
<br />SELF -ADHERED FLASHING
<br />INSIDE CORNER
<br />�Ground(�-
<br />FOUNDATION WEEP SCREED
<br />STRIP OF SAF
<br />DRAINAGE PLANE WRB
<br />BOND BREAK WRB
<br />SF LATH
<br />WRAP DP WRB ONTO
<br />THE VERTICAL
<br />SURFACE TO TOP OF
<br />FLANGE AS AN AIR
<br />BARRIER
<br />3-1/2" INCH FLANGE
<br />I�
<br />THIS GAP IS A RESULT OF
<br />NATURAL SHRINKAGE.
<br />DO NOT SEAL.
<br />DRIP SCREED PLASTIC
<br />ACCESSORY
<br />SOFFIT/CANTILEVER
<br />exterior fenestration products shall be sealed at the juncture with the building wall with a sealant complying with AAMA 800 or ASTM C920 Class
<br />SCORED 25 Grade NS or greater for proper joint expansion and contraction, ASTM C1281, AAMA 812, or other approved standard as appropriate for the
<br />RELEASE PAPER type of sealant. Fluid -applied membranes used as flashing in exterior walls shall comply with AAMA 714. The flashing shall extend to the surface
<br />(BEFORE FOLDING, SCORE of the exterior wall finish. Approved corrosion resistant flashings shall be installed at the following locations:
<br />RELEASE PAPER TO EXPOSE
<br />ADHESIVE AS SHOWN) 1. Exterior window and door openings. Flashing at exterior window and door openings shall extend to the surface of the exterior wall finish
<br />or to the water -resistive barrier complying with Section 703.2 for subsequent drainage. Mechanically attached flexible fleshings shall
<br />comply with AAMA 712. Flashing at exterior window and door openings shall be installed in accordance with one or more of the following:
<br />1.1 The fenestration manufacturer's installation and flashing instructions, or for applications not addressed in the fenestration
<br />manufacturer's instructions, in accordance with the flashing manufacturer's instructions. Where flashing instructions or details
<br />are not provided, pan flashing shall be installed at the sill of exterior window and door openings. Pan flashing shall be sealed or
<br />sloped in such a manner as to direct water to the surface of the exterior wall finish or to the water resistive barrier for subsequent
<br />2 drainage. Openings using pan flashing shall incorporate flashing or protection at the head and sides.
<br />/ 5 1.2. In accordance with the flashing design or method of a registered design professional.
<br />4 1.3. In accordance with other approved methods.
<br />1.4 In accordance with FMA/AAMA 100, FMA/ AAMA 200, FMA/WDMA 250, FMA/AAMA/ WDMA 300 or FMA/AAMA/WDMA 400.
<br />6 2. At the intersection of chimneys or other masonry construction with frame or stucco walls, with projecting lips on both sides under stucco
<br />7 copings.
<br />3. Under and at the ends of masonry, wood or metal copings and sills.
<br />M 4. Continuously above all projecting wood trim.
<br />5. Where exterior porches, decks or stairs attach to a wall or floor assembly of wood -frame construction.
<br />6. At wall and roof intersections.
<br />7. At built-in gutters.
<br />Water Resistant Barrier
<br />Lath
<br />Sheathing
<br />Stucco
<br />LEGEND
<br />SELF ADHERED FLASHING (SAF) o
<br />DRAINAGE PLANE (DP) WEATHER RESISTANT
<br />BARRIER (WRB)
<br />BOND BREAK WEATHER RESISTANT BARRIER -
<br />SELF FURRING (SF) LATH
<br />PLASTER ACCESSORY
<br />SHEATHING,'OSB', PLYWOOD, DENSGLASS
<br />STRUCTURAL FRAMING
<br />STRUCTURAL SHEATHING
<br />STRIP OF SAF
<br />DRAINAGE PLANE WRB
<br />�I BOND BREAK WRB
<br />-SF LATH
<br />ER STOP- - -
<br />A
<br />NUOUS BACKER ROD
<br />CANT
<br />VTITIOUS FINISH
<br />Cement Plaster
<br />in accordance
<br />with ASTMC926
<br />over wood 2nd
<br />floor
<br />THESE DETAILS ARE GENERIC AND MEANT TO SHOW GENERAL
<br />FLASHING AND WATERPROOFING METHODS TO BE USED.
<br />Cement
<br />Plaster
<br />over block
<br />1 st floor
<br />7/8" Cement Plaster
<br />in accordance with
<br />ASTMC926
<br />Felt backed metal
<br />lathe in accordance
<br />with ASTMC1063
<br />Building Paper
<br />-7116" O.S.B.
<br />sheathing
<br />Metal
<br />Flashing
<br />Weep Screed
<br />Installed As Per
<br />Manufact. Specs.
<br />Maintain
<br />Bottom of
<br />Weep Screed
<br />1 1/2"to 2"
<br />Above Roof
<br />Sheathing
<br />Note:
<br />The building paper and metal lath must be
<br />installed over the top of the weep screed.
<br />WEEP SCREED DETAIL
<br />SCALE: NOT TO SCALE
<br />7/8" Cement Plaster
<br />in accordance with
<br />ASTMC926
<br />Felt backed metal
<br />lathe in accordance
<br />with ASTM C1063
<br />Building Paper
<br />7/16" O.S.B.
<br />sheathing
<br />Stampede or similar
<br />cauk bottom
<br />joint only
<br />Weep Screed
<br />Installed As Per
<br />Manufact. Specs.
<br />1/2" Cementitious
<br />Decorative Finish
<br />All inside and
<br />outside corner will
<br />need to be miter
<br />cut and caulked all
<br />butt joints need to
<br />becaulked using
<br />Stampede or sim.
<br />caulk for all
<br />0
<br />0
<br />CV
<br />O
<br />0
<br />To the best of the Engineer's knowledge, information and belief,
<br />the structural plans and specifications contained
<br />within these
<br />drawings comply with the 2017
<br />Florida Building Code -
<br />Residential 6th Edition. Engineer's signature and
<br />seal is only for
<br />the structural engineering portions of the drawing pages bearing
<br />Engineer's signature and seal.
<br />to
<br />v
<br />,p
<br />8
<br />co
<br />ro
<br />N p W
<br />N 3k
<br />mom
<br />0
<br />go
<br />N NN
<br />ti(D
<br />CA ,
<br />5'D J
<br />LL
<br />J * W
<br />M
<br />4
<br />�ti Vu.LLa
<br />N M M
<br />W ' U
<br />J
<br />0
<br />O
<br />_
<br />c
<br />O
<br />O =
<br />W' m O
<br />i W
<br />L ,.��-
<br />o 2� o,
<br />m Co
<br />¢ a
<br />W
<br />LLZ
<br />(0J
<br />L0 Cl) 0
<br />(]
<br />of
<br />Z
<br />N Q
<br />OU
<br />U H J
<br />❑�❑
<br />�. W
<br />� M7
<br />N M
<br />z S
<br />z � �
<br />Q
<br />Uin
<br />Ul)
<br />M
<br />z
<br />a
<br />LL
<br />4-1 to
<br />fLi w
<br />U
<br />O
<br />V)0fN
<br />r
<br />r6
<br />^
<br />U
<br />w J
<br />zI%'
<br />U o' h
<br />0
<br />°
<br />N
<br />I�
<br />o
<br />co
<br />J
<br />w
<br />c' J
<br />co
<br />� a
<br />o
<br />z
<br />G
<br />111
<br />411..-
<br />U_
<br />i1 E
<br />o
<br />zo
<br />oo
<br />>ry
<br />¢N
<br />Za
<br />oa
<br />o E
<br />X OU
<br />ra
<br />ao
<br />,7 0U
<br />o<
<br />(D
<br />¢
<br />y oo
<br />aZ
<br />¢Z
<br />{�
<br />cJ� C
<br />C:
<br />o
<br />U
<br />.
<br />0
<br />O
<br />Z F
<br />Z
<br />-'
<br />2
<br /><�
<br />Q W
<br />�Z
<br />Cn 3:
<br />2
<br />Q
<br />cc M,
<br />5O
<br />a
<br />N W
<br />U
<br /><0
<br />oz
<br />�C
<br />=�
<br />O
<br />r
<br />c7 �-
<br />WO
<br />mi
<br />COO
<br />W
<br />�a
<br />°3�
<br />C:N
<br />0
<br />=
<br />>cc
<br />nL,
<br />c
<br />W
<br />\
<br />0
<br />Cy)
<br />00
<br />./ 0
<br />U
<br />>
<br />O
<br />U
<br />n' m
<br />OCD
<br />E O
<br />d.
<br />r
<br />= O
<br />r
<br />TT
<br />"It LO
<br />Ln
<br />r
<br />.L Cif
<br />rn
<br />r
<br />iu
<br />E
<br />w 00
<br />M
<br />o
<br />Z
<br />E
<br />d
<br />rO
<br />E
<br />U J
<br />Q 0
<br />C:
<br />J
<br />JOB
<br />NO :
<br />20-6226
<br />SCALE :
<br />AS NOTED
<br />SHEET NO.
<br />W P
<br />
|