|
I&
<br />r1�.dW.. U ...... .-_.: _.,A .. w►. eYll� s.L�k,l -. ..n. Y!
<br />THESE DETAILS ARE GENERIC AND
<br />MEANT TO SHOW GENERAL FLASHING
<br />AND WATERPROOFING METHODS TO
<br />BE USED.
<br />W CEMENT
<br />PLASTER
<br />12 MIL DRYLOK
<br />CMU - MASONRY BLOCK
<br />EXTREME
<br />WINDOW
<br />FASTENER
<br />.' ` . "• ` , 1) SEALANT AT
<br />" 4) SEALANT JOINT
<br />:,: '�.. WINDOW BUCK TO
<br />OUTSIDE EDGE OF
<br />" ' ' ' :� MASONRY
<br />WINDOW BUCK
<br />2) SEALANT JOINT
<br />5) SEALANT FROM
<br />, ,::' "; INSIDE EDGE OF
<br />WINDOW FRAME
<br />' 't, WINDOW BUCK
<br />ACROSS WINDOW BUCK
<br />AND EXTEND TO
<br />WINDOW FRAME
<br />MASONRY
<br />ATTACHED
<br />PER CODE
<br />6) TOOLED SEALANT
<br />REQUIREMENTS
<br />BEAD BRIDGING
<br />CLADDING AND WINDOW
<br />FRAME
<br />3) SEALANT WINDOW FRAME T(
<br />WINDOW BUCK ALL THE WAY
<br />AROUND, INCLUDING SILL.
<br />SCS 06_05 CMU INSTALLATION 6 POINT BUCK AND
<br />FENESTRATION INSTALLATION AND INTERFACE
<br />JAMB, SILL AND HEAD DETAIL
<br />APPROVED SHEATHING
<br />APPROVED HOUSEWRAP
<br />STRUCTALATH TWIN TRACK 2.5
<br />3A" CEMENT PLASTER
<br />12 MIL (min) DRYLOK EXTREME
<br />APPROVED FLASHING TAPE
<br />'V" SEALANT SOCKET WITH
<br />TOOLED APPROVED SEALANT
<br />SCS 06_02 WINDOW FIN INTERFACE WITH
<br />EXTRUDED SHOULDER
<br />WEATHER
<br />RESiSITIVE
<br />BARRIER
<br />WEATHER
<br />JE BARRIER &
<br />IARILY SECURE
<br />EXTERIOR
<br />SHEATHING
<br />WOOD FRAME CONSTR
<br />SELF -ADHERED FLASH IN
<br />BY LAPPING DOWN OVER RiM JOIST AND UP
<br />WALL BY 6 IN-
<br />WEATHER
<br />RESISITiVE
<br />BARRIER
<br />SEAL TOPS OF JOISTS -
<br />UNDER DECKING
<br />(SEE DETAIL WP07)
<br />ED FLASHING
<br />HEAD FLASHING TIE-IN INSTRUXTIONS:
<br />1. Cut, fold up & temporarily secure weather
<br />resistive barrier above header to allow for
<br />flashing installation
<br />2. Self -adhered flashing plus head flashing under
<br />weather resistive barrier �
<br />3. Fold weather resistive barrier back over heat 2
<br />flashing and seal with tape
<br />SELF -ADHERED FLASHING Scale: NTS
<br />FLANGED WINDOW [WP01
<br />FLASHING INSTALLATION AFTER WEATHER RESISTIVE BARRIER
<br />EXTERIOR SHEATHING
<br />REFER TO TECHNICAL
<br />LETTER ON CHEMICAL
<br />COMPATIBILITY
<br />SELF -ADHERED FLASHING -�
<br />DO NOT FLASH OVER
<br />BOTTOM NAILING
<br />FLANGE
<br />NAILING FLANGE
<br />SELF -ADHERED FLASHING
<br />HALF ROUND WINDOW
<br />SELF -ADHERED FLASHING
<br />PRODUCTS DETAILS
<br />WATER RESISTIVE BARRIERS ARE REQUIRED BEHIND STUCCO
<br />PER THE FBC RESIDENTIAL 7TH EDITION (2020)
<br />Detail Instructions
<br />Refer to the number marked as (i) in each detail that corresponds to the
<br />numbered Items In the list of instructions below,
<br />1. Install self -adhered flashing in order as shown by numbers
<br />2. Install flashing and weather resistive barrier to form water shedding
<br />laps
<br />3. Self -adhered flashing can be substituted for building paper
<br />4. Split the release paper using the ripcord (Split release on demand,
<br />embedded in the adhesive layer) - for ease of installation and to
<br />minimize scoring cuts
<br />5. Remove all release paper per standard installation instructions and
<br />adhere to substrate using a square piece of flashing material (6" x 6"
<br />Minimum)
<br />6. Fold as shown by arrows
<br />7. Angle of comer may vary, adjust folding of the flashing accordingly to
<br />fit tight to corner
<br />8- Mechanically fasten as necessary
<br />r�nannv�.a
<br />SELF -ADHERED FLASHING
<br />DECK JOIST
<br />2x FRAMEWALL
<br />TILE FiNISH-
<br />1/2" DUROCK-
<br />8" CMU
<br />4"ORR"CMU
<br />(PER SEAT DEPTH)
<br />FILL WITH GROUT -
<br />SLOPED MUD BED
<br />ViNYL SHOWER PAN
<br />SELF -ADHERED FLASHING
<br />PO
<br />IWPO7
<br />JVEATHER RESISTIVE
<br />BARRIER
<br />SELF -ADHERED FLASHING
<br />EXTERIOR DOOR WITH DECK - SECTION A
<br />3/4"-1" BEAD OF CC NSTR.
<br />ADHESIVE TO BE A'PLIE1
<br />THRESHOLD OF D( OR At
<br />UP JAMB 6 US:: Li )UiD iN
<br />OR EQUAL WEA.TH- P. PR(
<br />SECTION A (SEE DET AIL WPi
<br />SELF -ADHERED FLA.7HING
<br />SEAL TOPS OF )ISTS
<br />UNDER DECKINL-:
<br />(SEE DETAIL WP )-/)
<br />SELF-ADHER
<br />SELF -ADHERED FLASHING
<br />EXTERIOR DOOR WITH DECK
<br />SELF -ADHERED FLASHING
<br />OUTSIDE CORNER
<br />d g
<br />Q ' o_
<br />w w
<br />0- a
<br />W
<br />W U
<br />LU
<br />d Ir
<br />LU
<br />Cn
<br />O
<br />SHOWER SEAT I WP1 1
<br />-- WINDOW UNIT FLASHING REQUIREMENTS
<br />- DOOR ROUGH OPENING
<br />-
<br />SLOPE
<br />0.3 in: 12.0 in R703.1 General. Exterior walls shall provide the building with a weather -resistant exterior wall envelope. The exterior wall envelope shall
<br />3/4%11' BEAD OF CONSTR (0.6 cm : 30.5 cm) include flashing as described in Section R703,4.
<br />ADHESIVE TO BE APPLIED UNDER { SELF -ADHERED FLASHING
<br />THRESHOLD OF DOOR AND
<br />RETURN UP JAMB 6`. USE LIOIJID EXTERIOR R703.1.1 Water resistance. The exterior wall envelope shall be designed and constructed in a manner that prevents the accumulation of water
<br />"AIL BRAND OR EuIIAL WEATHER within the wall assembly b providing a water-resistant barrier behind the exterior cladding as required b Section R703.2 and a means of
<br />PROOF CAULKING CEMT. FIN. Y Y P 9 9 e4 Y
<br />�- SELF -ADHERED FLASHING BUILDING PAPER draining to the exterior water that penetrates the exterior Gadding.
<br />SUBFLOOR
<br />> WIRE LATH R703.2 Water -resistive barrier. One layer of No. 15 asphalt felt, free from holes and breaks, complying with ASTM D226 for Type 1 felt or other
<br />approved water -resistive barrier shall be applied over studs or sheathing of all exterior walls No. 15 asphalt felt shall be applied horizontally,
<br />with the upper layer lapped over the lower layer not less than 2 inches. Where joints occur, felt shall be lapped not less than 6 inches. Other
<br />approved materials shall be installed in accordance with the water -resistive barrier manufacturer's installation instructions. The No. 15 asphalt
<br />felt a oth r d t t b t I h II b th
<br />RIM JOIST r e approve wa er-reds the arn.,r ma erla s a e continuous to a top of walls and terminated at penetrations and building
<br />appendages in a manner to meet the requirements of the exterior wall envelope as described in Section R703.1.
<br />R703.7.3 Water -resistive barriers Water -resistive barriers shall be installed as required in Section R703.2 and, where applied over wood -based
<br />sheathing, shall include a water -resistive vapor -permeable barrier with a performance at least equivalent to two layers of Grade D paper. The
<br />individual layers shall be installed independently such that each layer provides a separate continuous plane and any flashing (installed in
<br />accordance with Section R703.4) intended to drain to the water -resistive barrier is directed between the layers.
<br />SELF -ADHERED FLASHING (�
<br />W P02 CEMT. FINISH SILL/ POTSHELF/ CHIMNEY SHOULDER W P03 Exception: Where the water -resistive barrier that is applied over wood -based sheathing has a water resistance
<br />equal to or greater than that of 60-minute Grade D paper and is separated from the stucco by an intervening,
<br />MECHANICALLY FASTEN IF RUBBERIZED RUBBERIZED ASPHALT substantially nonwater-absorbing layer or designed drainage space.
<br />NEEDED IN CORNERS ADHESIVE
<br />[STALL SELF AL1HEIzt;J ASPHALT ADHESIVE
<br />THROUGH SELF -ADHERED g. pp g, Y g Y g pp
<br />a�sHsr�c �e � HEAD R703.4 Flashing. Approved metal flashing, vinyl flashing, self -adhered membranes and mechanical) attached flexible flashing shall be applied
<br />ASHING, SEE FLASHING SELF -ADHERED FLASHING
<br />-ANGEDVIANDOW shingle -fashion or in accordance with the manufacturer's instructions. Metal flashing shall be corrosion resistant. Fluid -applied membranes
<br />EE DETMLWPo11 used as flashing shall be applied in accordance with the manufacturer's instructions. All flashing shall be applied in a manner to prevent the
<br />SCORED entry of water into the wall cavity or penetration of water to the building structural framing components.
<br />RELEASE PAPER Self -adhered membranes used as flashing sha!I comply With AAMA 711. All exterior fenestration products shall be sealed at the juncture with
<br />=LF A(IIF D PLASHING. '- -. 14��L�^'oRE the building wall with a sealant complying With AAMA 800 or ASTM C920 Class 25 Grade NS or greater for proper joint expansion and
<br />RELEASE AEAS TO WN,sE contraction, ASTMC1281, AAMA 812, or other approved standard as appropriate for the {"°LMvM1c gin, pptype of sealant. Fluid -applied membranes used as
<br />)TTOMOF flashing in exterior walls shall comply with AAMA 714. The flashing shall extend to the surface of the exterior wall finish. Approved flashings
<br />AREHOLD
<br />shall be installed at the following locations:
<br />i.
<br />1.1,Exterior window and door openings. Flashing at exterior window and door openings shall extend to the surface of the exterior wall
<br />finish or to the water -resistive barrier complying with Section 703.2 for subsequent drainage. Mechanically attached flexible flashings
<br />2 shall comply with AAMA 712. Flashing at exterior window and door openings shall be installed in accordance with one or more of the
<br />following:
<br />5 1.1 The fenestration manufacturer's installation and flashing instructions, or for applications not addressed in the fenestration
<br />4 manufacturer's instructions, in accordance with the flashing manufacturer's instructions. Where flashing instructions or details are
<br />not provided, pan flashing shall be installed at the sill of exterior window and door openings. Pan flashing shall be sealed or
<br />1 6 sloped in such a manner as to direct water to the surface of the exterior wall finish or to the water resistive barrier for subsequent
<br />7 drainage. Openings using pan flashing shall incorporate flashing or protection at the head and sides.
<br />1.2 1.2. In accordance with the flashing design or method of a registered design professional.
<br />("�
<br />SELF -ADHERED FLASHING 1.3 1.3. In accordance with other approved methods.
<br />�/� J
<br />Y Y P05 INSIDE CORNER WP06 1.4 In accordance with FMA/AAMA 100, FMA/ AAMA 200, FMA/WDMA 250, FMA/AAMA/ WDMA 300 or FMA/AAMAfWDMA 400.
<br />2- 2.At the intersection of chimneys or other masonry construction with frame or stucco walls, with projecting lips on both sides under
<br />stucco copings.
<br />Ground 3.3.Under and at the ends of masonry, wood or metal copings and sills.
<br />4.4.Continuously above all projecting wood trim.
<br />5.5.Where exterior porches, decks or stairs attach to a wall or floor assembly of wood -frame construction.
<br />6.6,At wall and roof intersections.
<br />Water Resistant Barrier 7.7.At built-in autters.
<br />:LF-ADHERED FLASHING
<br />kTCH
<br />IHERED FLASHING
<br />i,,22
<br />c4
<br />�5
<br />VTP08
<br />PLASTER STOP J_;�
<br />CONTINUOUS BACKER
<br />ROD & SEALANT
<br />A�
<br />FOUNDATION WEEP SCREED
<br />STRIP OF SAF
<br />DRAINAGE PLANE WRB
<br />BOND BREAK WRB
<br />SF LATH
<br />WRAP DP WRB ONTO
<br />THE VERTICAL
<br />SURFACE TO TOP OF
<br />FLANGE AS AN AIR
<br />BARRIER
<br />3-112" INCH FLAKE
<br />7 �y THIS GAP IS A RESULT OF
<br />NATURAL SHRINKAGE
<br />DONOT SEAL.
<br />�- DRIP SCREED PLASTIC
<br />ACCESSORY
<br />SOFFIT/CANTILEVER
<br />Lath
<br />Sheathing
<br />Stucco
<br />LEGEND
<br />SELF ADHERED FLASHING (SAF)
<br />DRAINAGE PLANE (DP) WEATHER RESISTANT
<br />BARRIER (WRB)
<br />BOND BREAK WEATHER RESISTANT BARRIER --
<br />SELF FURRING (SF) LATHf�-
<br />PLASTER ACCESSORY
<br />SHEATHING. 'OSB•. PLYWOOD. DENSGL4SS
<br />STRUCTURAL FRAMING
<br />STRUCTURAL SHEAT1110r,
<br />STRIP OF SAF
<br />DRAINAGE PLANE WRB
<br />V,
<br />1"SF
<br />BOND BREAK WRB
<br />LATH
<br />I�
<br />8
<br />ER STOP A
<br />NIJ0115 RACKER RnD
<br />LANT
<br />tITITIOUS FINISH
<br />WP10
<br />in
<br />W
<br />Ov
<br />flt
<br />THESE DETAILS ARE GENERIC AND MEANT TO SHOW GENERAL
<br />FLASHING AND WATERPROOFING METHODS TO BE USED.
<br />- 7/8" Cement Plaster
<br />t/3
<br />U
<br />0
<br />�+
<br />C
<br />O
<br />cu
<br />.
<br />(n
<br />.�
<br />CO
<br />cu
<br />t%)
<br />0
<br />O
<br />0
<br />0
<br />Oja
<br />ILL
<br />ca
<br />0_o
<br />Ce
<br />j
<br />>
<br />. �
<br />(ID
<br />O
<br />Oe_
<br />CU
<br />u)
<br />!~L
<br />d
<br />JUL 14
<br />ual Review Assist, Inc. Plans R iew completed and app oved
<br />7/8" Cement P4lirsWrIPti ce with the 2020 FBC 7111 Edition
<br />in accordance with by ebra Anne Klahr PX230
<br />ASTMC926
<br />Felt backed metal
<br />lathe in accordance
<br />with ASTMC1063
<br />Building Paper
<br />7/16" O.S.B. cn
<br />sheathing
<br />Stampede or similar
<br />cauk bottom
<br />joint only
<br />Weep Screed
<br />Installed As Per
<br />Manufact. Specs.
<br />1/2" Cementitious
<br />)ecorative Finish
<br />All inside and
<br />Dutside comer will
<br />need to be miter
<br />Cut and caulked all
<br />tIutt joints need to
<br />tiecaulked using
<br />Stampede or sim.
<br />Caulk for all
<br />r�
<br />V �
<br />ICU
<br />0.
<br />CL
<br />o
<br />0
<br />Q_
<br />CD
<br />CU
<br />00
<br />w
<br />Q
<br />Z
<br />Z
<br /><
<br />J
<br />Q_
<br />SHEET NO.
<br />WP1
<br />so
<br />
|