|
2
<br />3
<br />4
<br />a
<br />u
<br />Q
<br />F.
<br />W
<br />m
<br />`o
<br />ca
<br />rn�
<br />ry
<br />0
<br />U
<br />C
<br />n
<br />1. COMPLY WITH NEW CONSTRUCTION AND RCP REQUIREMENTS OF THE GENERAL NOTES IN THIS
<br />SET OF DRAWINGS WHICH ALSO APPLY TO THE DEMOLITION FLOOR PLANS.
<br />2. THE DEMOLITION DRAWINGS HAVE BEEN DEVELOPED FROM EXISTING DRAWINGS PROVIDED TO
<br />THE ARCHITECT/ENGINEER BY THE OWNER, AND MAY NOT REFLECT ACTUAL FIELD CONDITIONS.
<br />PRIOR TO PROCEEDING WITH ANY WORK, VERIFY THE ACCURACY OF THESE DRAWINGS IN
<br />COMPARISON TO EXISTING FIELD CONDITIONS AND IMMEDIATELY NOTIFY THE ARCHITECT OF ANY
<br />INCONSISTENCIES BETWEEN THESE DRAWINGS AND ACTUAL CONDITIONS.
<br />3. EXISTING -TO -REMAIN PARTITIONS, DOORS, WINDOWS, PLUMBING FIXTURES, CASEWORK,
<br />EQUIPMENT, ARE "SCREEN -BACK" ON DEMOLITION PLANS. ITEMS TO BE REMOVED ARE INDICATED
<br />BY DASHED LINES.
<br />4. REMOVE EXISTING CONSTRUCTION AS INDICATED. WALL REMOVAL INCLUDES MECHANICAL,
<br />PLUMBING, ELECTRICAL, COMMUNICATIONS AND SECURITY SYSTEMS CONTAINED THEREIN. REMOVE
<br />DOORS, CASEWORK, WINDOWS, FRAMES, FINISHES, FIXTURES AND THEIR ATTACHMENTS AS
<br />INDICATED.
<br />5. REFER TO MECHANICAL, PLUMBING, FIRE PROTECTION, AND ELECTRICAL DRAWINGS FOR
<br />DEMOLITION OF UTILITIES.
<br />6. AT PARTITIONS, FLOORS AND ROOFS WHICH ENCLOSE THE CONSTRUCTION AREA VERIFY THAT
<br />THE EXISTING CONSTRUCTION, INCLUDING BUT NOT LIMITED TO DAMPERS, DUCT PENETRATIONS,
<br />DOORS, WINDOWS AND FRAMES, MEETS THE FIRE, SMOKE AND SOUND ASSEMBLY RATINGS
<br />DESIGNATED ON THESE DRAWINGS. NOTIFY THE ARCHITECT IMMEDIATELY IF DISCREPANCIES ARE
<br />DISCOVERED. AS DIRECTED, MAKE REPAIRS AND/OR MODIFICATIONS NECESSARY TO BRING THE
<br />EXISTING CONSTRUCTION UP TO THE INDICATED FIRE, SMOKE AND SOUND ASSEMBLY RATINGS.
<br />7. EXECUTE DEMOLITION WORK IN CONFORMANCE WITH ALL CODES AND ORDINANCES AS SET
<br />FORTH BY ALL AUTHORITIES HAVING JURISDICTION.
<br />8. BRACE EXISTING STRUCTURAL ELEMENTS AS NECESSARY DURING DEMOLITION.
<br />9. DO NOT CUT STRUCTURAL ELEMENTS IN ANY MANNER THAT MAY RESULT IN A REDUCTION OF
<br />LOAD CARRYING CAPACITY OR LOAD/DEFLECTION RATIO. NOTIFY THE ARCHITECT IN WRITING OF ALL
<br />STRUCTURAL CUTS PRIOR TO EXECUTION SO THAT APPROVAL CAN BE OBTAINED IN ADVANCE FROM
<br />THE ARCHITECT.
<br />10. WHEN HAZARDOUS MATERIALS ARE FOUND, STOP WORK AND IMMEDIATELY NOTIFY THE OWNER
<br />AND THE ARCHITECT IN WRITING. REMOVAL, DISPOSAL, AND REPLACEMENT OF HAZARDOUS
<br />MATERIALS IS THE SOLE RESPONSIBILITY OF THE OWNER.
<br />11. COORDINATE ALL ICRA REQUIREMENTS WITH THE OWNER
<br />12. COMPLETE DEMOLITION WORK OUTSIDE THE AREA OF CONSTRUCTION WITH ISOLATED
<br />PORTABLE "DUST -BUGGIES" OR WORK BOOTHS.
<br />13. REMOVE ALL ABANDONED ABOVE CEILING EQUIPMENT INCLUDING BUT NOT LIMITED TO,
<br />MOUNTED HANGER WIRES, SUPPORT BRACKETS, HANGER RODS, AND MOUNTING STRAPS.
<br />14. IN ACCORDANCE WITH NFPA 51 B AND NFPA 601, OBTAIN A HOT WORK PERMIT PRIOR TO
<br />BEGINNING ANY WELDING, CUTTING, BRAZING, GRINDING OR OTHER ACTIVITIES THAT GENERATE
<br />SPARKS CAPABLE OF CAUSING COMBUSTION.
<br />15. AS REQUIRED BY NFPA 30, CHAPTER 22, REMOVE ALL FLAMMABLE ITEMS, INCLUDING BUT NOT
<br />LIMITED TO COMPRESSED AIR AND GAS CANS OR CYLINDERS I.E. BRAZING, ACETYLENE, PROPANE
<br />TANKS, PAINT CANS, LUBRICANTS, ETC. FROM THE JOB SITE WHEN THE PROJECT HAS BEEN
<br />VACATED BY CONSTRUCTION PERSONNEL FOR THE DAY AND DURING ANY TIME THE FIRE ALARM
<br />SYSTEM AND FIRE SUPPRESSION SYSTEM ARE INACTIVE.
<br />1. THE EXISTING LIFE SAFETY PLANS WERE PROVIDED TO THE ARCHITECT BY THE PROPERTY
<br />OWNER. RS&H, INC., TAKES NO RESPONSIBILITY FOR THEIR ACCURACY. RS&H HAS REVISED ONLY
<br />THAT AREA WITHIN THE SCOPE OF WORK.
<br />2. THE LIFE SAFETY PLANS ARE "DIAGRAMMATIC ONLY". THEIR PURPOSE IS TO REPRESENT THE
<br />LIFE SAFETY COMPONENTS FOR THE PROJECT AS INCLUDED IN THE CONSTRUCTION DOCUMENTS
<br />PREPARED BY THE ARCHITECT, ELECTRICAL ENGINEER, ETC. USE THE CONSTRUCTION
<br />DOCUMENTS, NOT THE LIFE SAFETY PLANS, FOR THE IMPLEMENTATION OF THE REQUIRED LIFE
<br />SAFETY COMPONENTS INTO THE PROJECT.
<br />3. ADVISE THE ARCHITECT IMMEDIATELY UPON DISCOVERY OF ANY LIFE SAFETY COMPONENT THAT
<br />IS SHOWN ON THE LIFE SAFETY PLANS BUT HAS NOT BEEN INCLUDED IN THE CONSTRUCTION
<br />DOCUMENTS PREPARED BY THE ARCHITECT, ELECTRICAL ENGINEER, ETC.
<br />4. FIELD VERIFY THAT THE REQUIRED VISIBILITY FOR EACH INDIVIDUALLY INSTALLED EXIT LIGHT IS
<br />NOT IN ANY WAY DIMINISHED DUE TO VISUAL INTERFERENCE CAUSED BY ANY OTHER LIGHT
<br />FIXTURES, DEVICES, SIGNS, ETC. COORDINATE WITH THE REFLECTED CEILING PLANS, THE
<br />ELECTRICAL DRAWINGS, THE GRAPHICS DRAWINGS, ETC.
<br />1. SUBMIT PLANS TO OBTAIN A SEPARATE PERMIT FOR THIS WORK.
<br />2, COMPLY WITH THE CURRENTLY ADOPTED VERSION OF NFPA 13
<br />3. ONLY A LICENSED CONTRACTOR EXPERIENCED WITH THIS TYPE OF WORK SHALL PERFORM
<br />WORK.
<br />4. REUSE THE EXISTING SPRINKLER SYSTEM WHEN POSSIBLE. PROVIDE NEW HEADS AT LOCATIONS
<br />AS REQUIRED.
<br />5. PROVIDE TEMPORARY FIRE PROTECTION OF BUILDING AS REQUIRED.
<br />6. PROVIDE SHOP DRAWINGS FOR ARCHITECT'S/ENGINEER'S REVIEW, INCLUDING PIPING,
<br />PROPOSED LOCATIONS, AND NEW SPRINKLER HEADS, AT ALL LOCATIONS.
<br />7. RELOCATE AND/OR INSTALL SUFFICIENT HEADS IN ALL SPACES TO PROVIDE COMPLETE (100%)
<br />AUTOMATIC SPRINKLER COVERAGE AS DEFINED IN NFPA STANDARD 13, - FIRE SUPPRESSION AND
<br />AS SHOWN ON THE FIRE PROTECTION DRAWINGS.
<br />8. DO NOT PAINT SPRINKLER HEADS OR CONCEALED SPRINKLER HEAD COVERS. REPLACE ANY
<br />SPRINKLER HEADS THAT ARE ACCIDENTALLY PAINTED WITH NEW ONES.
<br />9. FOR SPACES WITH FIRE SPRINKLER HEADS AND WHERE TALL STORAGE IS ANTICIPATED (EITHER
<br />OWNER OR CONTRACTOR FURNISHED) PAINT A 1" THICK RED LINE ON THE WALLS AT 18" BELOW
<br />THE BOTTOM OF THE LOWEST SPRINKLER HEAD. PAINT OR INSTALL PERMANENT SIGNAGE ABOVE
<br />THE LINE, "STORAGE IS NOT PERMITTED ABOVE THIS LINE".
<br />1. REPAIR ANY EXISTING FIREPROOFING OR RATED WALL ASSEMBLIES DAMAGED DURING DEMOLITION.
<br />REPAIRS MUST CONFORM TO THE ORIGINAL FIRE PROTECTION REQUIREMENTS. MAINTAIN THE
<br />INTEGRITY OF EXISTING RATED FLOORS, BARRIERS, AND ROOF ASSEMBLIES THROUGHOUT ALL PHASES
<br />OF CONSTRUCTION. CONTACT ARCHITECT TO PROVIDE TESTED ASSEMBLIES FOR REPAIRS.
<br />2. WHERE DEMOLITION OF ITEMS RESULTS IN UNPROTECTED OPENINGS OR PENETRATIONS IN EXISTING
<br />FLOORS, WALLS, CEILING OR ROOFS, REPAIR OPENINGS AND PENETRATIONS AS REQUIRED TO MEET
<br />ORIGINAL FIRE PROTECTION, SOUND AND STRUCTURAL REQUIREMENTS.
<br />3. SEAL ALL EXISTING AND/OR ABANDONED PENETRATIONS IN ACCORDANCE WITH THE APPROPRIATE
<br />U.L. DESIGN.
<br />4. SUBMIT ALL MODIFICATIONS TO THE FIRE ALARM OR FIRE SPRINKLER SYSTEM, INCLUDING
<br />AUDIOVISUAL COMMUNICATION DEVICES TO THE CITY FOR SEPARATE PERMITTING.
<br />5. STENCIL EACH "WALL/PARTITION/BARRIER" CLASSIFICATION IN RED LETTERS ABOVE THE FINISHED
<br />CEILING ON EACH SIDE OF ALL FIRE WALLS, RATED FIRE BARRIERS, RATED SMOKE BARRIERS, NOW
<br />RATED SMOKE PARTITIONS, ETC.
<br />7. "LIMITS OF CONSTRUCTION" AND "SCOPE OF WORK" LINES SHOWN ON THE ARCHITECT'S PLANS
<br />APPLY ONLY TO THE LIMITS OF ARCHITECTURAL NEW CONSTRUCTION AND RENOVATION. SEE OTHER
<br />DISCIPLINES' DRAWINGS FOR THE LIMITS OF THE NEW CONSTRUCTION AND RENOVATION FOR THOSE
<br />DISCIPLINES.
<br />8. EXISTING -TO -REMAIN ITEMS SUCH AS PARTITIONS, DOORS, WINDOWS, PLUMBING FIXTURES,
<br />CASEWORK, AND EQUIPMENT ARE "SCREENED -BACK" ON NEW CONSTRUCTION AND DIMENSION PLANS
<br />NEW ITEMS ARE INDICATED BY DARK SOLID LINES. REFER TO DEMOLITION FLOOR PLANS FOR EXTENT
<br />OF "EXISTING -TO -BE -REMOVED".
<br />9. ITEMS ANNOTATED ON THE NEW CONSTRUCTION FLOOR PLANS WITH DASHED OR DOTTED LINES ARE
<br />OWNER FURNISHED ITEMS OR OVERHEAD ITEMS
<br />10. DO NOT SCALE THE DRAWINGS. IF DIMENSIONS ARE IN QUESTION, OBTAIN CLARIFICATION FROM THE
<br />ARCHITECT IN WRITING PRIOR TO CONTINUING WITH CONSTRUCTION.
<br />11. DIMENSIONS SHOWN ON THE FLOOR PLANS ARE TO FACE OF STUD ON NEW PARTITIONS OR TO
<br />OUTSIDE FACE OF EXISTING WALLS. CRITICAL MINIMUM DIMENSIONS ARE INDICATED AS "MINIMUM",
<br />"CLEAR", OR "MINIMUM CLEAR".
<br />12. CONSIDER THE THICKNESS OF THE SCHEDULED FINISH MATERIALS PRIOR TO CONSTRUCTING
<br />PARTITIONS SO THE REQUIRED "MINIMUM CLEAR" DIMENSIONS ARE MAINTAINED AFTER THE
<br />INSTALLATION OF THE FINISH MATERIALS.
<br />13. REFER TO ENLARGED PLANS, WALL SECTIONS, INTERIOR ELEVATIONS, PLAN DETAILS AND SECTION
<br />DETAILS FOR DIMENSIONING NOT SHOWN ON FLOOR PLANS.
<br />14. WHERE NEW PARTITIONS ARE ADDED TO EXISTING PARTITIONS, ALIGN NEW GYPSUM BOARD FACE
<br />WITH EXISTING ADJACENT WALL FACE. IF NECESSARY, OFFSET STUD LOCATION TO MAINTAIN GYPSUM
<br />BOARD ALIGNMENT.
<br />15. REPLACE OR REPAIR EXISTING MATERIALS AND FINISHES INCLUDING BUT NOT LIMITED TO CEILING
<br />GRID, CEILING TILE, GYPSUM BOARD, DOORS, WINDOWS, FRAMES, OR WALL PROTECTION, WHICH ARE
<br />DAMAGED DURING DEMOLITION OR CONSTRUCTION.
<br />16. PROVIDE NEW GYPSUM BOARAD, OR PATCH AND REFINISH EXISTING WALL SURFACE IF DAMAGE
<br />HAS OCCURRED FROM REMOVAL OF OLD FINISH. PROVIDE SPECIFIED NEW FINISH ON WALLS.
<br />17. BUNDLE TIE AND INDEPENDENTLY SUPPORT ALL NEW AND EXISTING LOW VOLTAGE CABLING ABOVE
<br />THE CEILING,
<br />1. COMPARE THE REFLECTED CEILING PLANS WITH ELECTRICAL LIGHTING, SYSTEMS,
<br />COMMUNICATIONS, MECHANICAL AND FIRE PROTECTION DRAWINGS. NOTIFY THE ARCHITECT IN
<br />WRITING OF ANY ERROR, INCONSISTENCY OR OMISSION THAT IS DISCOVERED.
<br />2. CEILING MOUNTED EXIT LIGHTS ONLY ARE SHOWN ON THE REFLECTED CEILING PLANS. REFER
<br />TO THE ELECTRICAL DRAWINGS FOR LOCATIONS OF WALL MOUNTED EXIT LIGHTS. MOUNT
<br />CEILING MOUNTED EXIT LIGHTS NO LOWER THAN T-0" CLEAR AFF.
<br />3. IF CEILING GRID OR CEILING TILES WHICH ARE NOTED TO REMAIN OR BE REINSTALLED ARE
<br />DAMAGED, REPLACED THEM WITH NEW MATERIAL THAT MATCHES THE EXISTING IN COLOR,
<br />MATERIAL, SIZE, AND PROFILE. IF THESE ITEMS CANNOT BE MATCHED, PROVIDE NEW GRID AND
<br />TILES FOR THE ENTIRE SPACE. OBTAIN APPROVAL FOR NEW MATERIAL FROM OWNER AND
<br />ARCHITECT IN WRITING.
<br />4. REFER TO INTERIOR DRAWINGS FOR THE FINISH LEGEND AND SCHEDULE FOR PAINTED
<br />CEILINGS AND INTERIOR SOFFITS, PAINT HORIZONTAL SURFACES OR SOFFITS THE SAME COLOR
<br />AS THE VERTICAL SURFACES, UNLESS NOTED OTHERWISE.
<br />5. CENTER RECESSED CAN LIGHT FIXTURES IN GYPSUM BOARD SOFFITS AND CEILING TILES,
<br />UNLESS NOTED OTHERWISE, ALIGN AND EQUALLY SPACE RECESSED CAN LIGHT FIXTURES IN A
<br />SERIES.
<br />1. ALL WORK SHALL CONFORM TO ALL APPLICABLE CODES, STANDARDS AND GOVERNING
<br />AUTHORITIES.
<br />2. THESE DRAWINGS ARE ISSUED IN CONJUNCTION WITH THE PROJECT MANUAL OF THE SAME DATE,
<br />TITLE AND PROJECT NUMBER AND TOGETHER ARE REFERRED TO AS "CONTRACT DOCUMENTS."
<br />3. CONTRACT DOCUMENTS ARE INCLUSIVE OF ALL DISCIPLINES DRAWINGS AND SPECIFICATIONS. THE
<br />CONTRACTOR IS RESPONSIBLE FOR COORDINATION ACROSS ALL DRAWINGS.
<br />4. THE EXTENT OF THE WORK SHOWN ON THE PLANS AND DETAILS REFLECTS THE BEST JUDGMENT
<br />OF THE ARCHITECT/ENGINEER.
<br />5. FIELD VERIFY EXISTING CONDITIONS AND THE LOCATION OF ALL EXISTING UTILITIES. COMPARE THE
<br />INFORMATION TO THE CONTRACT DOCUMENTS PRIOR TO THE COMMENCEMENT OF ALL WORK. NOTIFY
<br />THE OWNER AND ARCHITECT IN WRITING OF DISCREPANCIES OR EXISTING CONDITIONS WHICH ARE
<br />ANTICIPATED TO HINDER OR PREVENT THE PROPOSED WORK.
<br />6. PROTECT ALL EXISTING SITE ELEMENTS FROM DAMAGE DUE TO ALTERATION AND CONSTRUCTION
<br />OPERATIONS. REPAIR OR REPLACE ELEMENTS DAMAGED DURING THE PROJECT.
<br />7. COORDINATE ANY REQUIRED UTILITY SHUT -OFFS DURING CONSTRUCTION WITH THE OWNER AND
<br />UTILITY COMPANY. PROVIDE A MINIMUM OF 72 HOURS NOTICE PRIOR TO COMMENCING WORK.
<br />8. DETAILS SHOWN ARE INDICATIVE OF THE PROFILES AND TYPE OF DETAILING REQUIRED FOR THE
<br />WORK. DETAILS NOT SHOWN ARE SIMILAR IN CHARACTER TO THOSE SHOWN.
<br />9. CONCEAL ALL FASTENERS AND FASTENING DEVICES IN FINISHED SPACES, UNLESS NOTED
<br />OTHERWISE.
<br />10. SEAL PIPING, DUCTS, CONDUITS OR OTHER OPENINGS THAT PENETRATE FIRE RATED FLOOR
<br />SLABS, WALLS, CEILINGS OR ROOF ASSEMBLIES IN A MANNER THAT PRESERVES THE FIRE INTEGRITY
<br />OF THE ASSEMBLY. PROVIDE FIRE DAMPERS IN DUCTS PENETRATING FIRE -RATED ASSEMBLIES TO
<br />MEET THE APPLICABLE BUILDING CODES.
<br />11. PROVIDE CONTINUOUS PERIMETER FIRE SAFING BETWEEN FLOORS. PROVIDE FIRE STOPS TO
<br />SEPARATE WALL CAVITIES FROM HORIZONTAL PLENUM AREAS. COORDINATE WITH THE EXTERIOR
<br />WALL SYSTEMS AND U.L. ASSEMBLIES. THE FIRE SAFING RATING SHALL MATCH OR EXCEED THAT OF
<br />THE FLOOR AND WALL CONSTRUCTION RATING.
<br />12. THE FIRE OR SMOKE RATINGS NOTED ON THE DRAWINGS APPLY TO THE ENTIRE PERIMETER
<br />ENCLOSURE OF THE ROOM OR SPACE FOR THE FULL LENGTH AND HEIGHT OF AREAS BEING
<br />SEPARATED. EXTEND WALLS FROM FLOOR TO THE UNDERSIDE OF THE FLOOR OR ROOF DECK.
<br />13. MAINTAIN THE FIRE -RATING NOTED IN THE DRAWINGS AROUND CABINETS, PANELS AND BOXES
<br />RECESSED IN A FIRE -RATED FLOOR, WALL OR CEILING ASSEMBLY.
<br />14. INSTALL FIRE RATED CONSTRUCTION ELEMENTS PER THE MANUFACTURER'S PUBLISHED TEST
<br />ASSEMBLIES. SEAL JOINTS TO PREVENT THE PASSAGE OF SMOKE AND FLAME.
<br />15. TO AVOID GALVANIC REACTION, ISOLATE DISSIMILAR METALS FROM EACH OTHER BY GASKETS OR
<br />COATINGS OR BOTH.
<br />16. PIPE AND COLUMN FURRING SHALL BE HELD AS CLOSE TO THE ELEMENT AS POSSIBLE, UNLESS
<br />NOTED OTHERWISE.
<br />17. THE ARCHITECT/ENGINEER'S SELECTION OF MATERIALS AND DETAILS DOES NOT RELIEVE THE
<br />CONTRACTOR FROM VERIFYING WITH THE MATERIAL SUPPLIERS THAT THE PROPOSED MATERIALS
<br />ARE CORRECT AND PROPER FOR THE INTENDED APPLICATION AND USE.
<br />18. REINFORCE CONCRETE FILLS ABOVE STRUCTURAL SLABS. REFER TO STRUCTURAL DRAWINGS FOR
<br />ADDITIONAL REQUIREMENTS.
<br />19. WHERE AN ARCHITECTURAL FINISHED FLOOR IS PROVIDED WHICH REQUIRES A DEPRESSED
<br />STRUCTURAL SLAB, THE FLOOR ELEVATIONS ARE TO TOP OF FINISHED FLOOR. WHERE
<br />ARCHITECTURAL FINISHES ARE INTENDED FOR SURFACE APPLICATION, THE FLOOR ELEVATIONS ARE
<br />TO TOP OF STRUCTURAL SLAB. REFER TO STRUCTURAL DRAWINGS FOR LOCATION OF DEPRESSED
<br />SLABS.
<br />20. UNLESS NOTED OTHERWISE, INSTALL REINFORCED CONCRETE PADS UNDER ALL FLOOR MOUNTED
<br />MECHANICAL AND ELECTRICAL EQUIPMENT. REFER TO DRAWINGS FOR THE EXTENT OF EQUIPMENT
<br />PADS. COORDINATE THE SIZE, THICKNESS AND LOCATION OF THE CONCRETE PADS WITH THE
<br />EQUIPMENT PROVIDER OR MANUFACTURER.
<br />21. WHERE MATERIALS ARE APPLIED TO, OR ARE IN DIRECT CONTACT WITH WORK INSTALLED BY
<br />ANOTHER SUBCONTRACTOR, COMMENCEMENT OF WORK IMPLIES THE ACCEPTANCE OF THE
<br />SUBSTRATE AND EXISTING CONDITIONS AS SUITABLE FOR THE APPLICATION INTENDED.
<br />22. CONSTRUCT NEW HORIZONTAL SURFACES LEVEL AND FLAT. CONSTRUCT NEW VERTICAL
<br />SURFACES PLUMB, UNLESS NOTED OTHERWISE.
<br />23. ACCORDING TO THE MANUFACTURER'S RECOMMENDATIONS, PROVIDE BLOCKING IN WALLS,
<br />SOFFITS, AND CEILINGS RECEIVING SIGNAGE, COAT HOOKS, LOCKERS, MARKER BOARDS, TOILET
<br />ACCESSORIES AND OTHER MOUNTED ITEMS.
<br />24. CONFIRM AND FIELD VERIFY DIMENSIONS TO COORDINATE WITH OWNER PROVIDED EQUIPMENT
<br />AND FURNISHINGS.
<br />25. SUBSTITUTIONS OF MATERIALS MAY OCCUR IN ACCORDANCE WITH THE CONTRACT DOCUMENTS,
<br />AND ONLY IF AUTHORIZED BY THE ARCHITECT.
<br />26. INSTALL ONLY MATERIALS THAT ARE NEW AND DELIVERED TO THE SITE IN GOOD CONDITION AND
<br />WITHOUT ANY DEFECTS.
<br />27. ANY WORK NOT CONFORMING TO THE CONTRACT DOCUMENTS WILL BE REJECTED BY THE
<br />ARCHITECT OR THE OWNER. REMOVE AND REPLACE REJECTED WORK AT NO ADDITIONAL COST TO
<br />THE OWNER.
<br />301 E. Pine Street, Suite 350
<br />Orlando, Florida 32801
<br />407-893-5800 Fax 407-264-6624
<br />www.rsandh.com
<br />FL Cert. Nos. AAC001886 * IB26000956
<br />5620 * LCC000210 * GB238
<br />PROJECT TITLE:
<br />AdventHealth - ZEPHYRHILLS
<br />OPERATING ROOMS 8 & 9 BUILD
<br />OUT
<br />PROJECT ADDRESS:
<br />7050 GALL BLVD,
<br />ZEPHYRHILLS, FL, 33541
<br />�E OF FCO
<br />EW TYtF RHO
<br />C7..' T R
<br />AR 99970
<br />RED A_
<br />SIGNATURE
<br />5-(4_ Al
<br />DATE
<br />REVISIONS
<br />NO. DESCRIPTION DATE
<br />DATE ISSUED:
<br />12/11/2019
<br />REVIEWED BY:
<br />ML
<br />DRAWN BY:
<br />TH
<br />DESIGNED BY:
<br />MW
<br />PROJECT NUMBER:
<br />504-0253-000
<br />0 2019 RS&H, INC.
<br />SHEET TITLE:
<br />GENERAL NOTES
<br />SHEET ID:
<br />BLDG. ID
<br />G002
<br />PROJECT STATUS:
<br />CONSTRUCTION
<br />DOCUMENTS
<br />Copyright 0 2019. This drawing is an instrument of service and property of RS&H, Inc. Any use or reproduction without the
<br />expressed written consent of this corporation is prohibited. All rights reserved.
<br />3" SCALE 0 3" 6" 1'
<br />1 1/2" SCALE 0 6" 12'
<br />3/8" SCALE 1 3'
<br />1/4" SCALE 4' 0 2' 4' 8'
<br />_ - ,- ��r�, nrw i�Y�_ a. 1,: :- ii�i naL.uSGLL�Li IWYIiiRIIJiII�IW�':wdru�:'c:i ud � �e-°.�: sr m-r � _�7v
<br />1 /8" SCALE 8' 0 4' 8' 16'
<br />
|