7209 Greenslope Dr (2) - Laserfiche WebLink

Browse Search

N 0 N S -2 d- MY .-Z+., LOW cfl 00 HANGER ROD. PROVIDE A SECTION OF HIGH COMPRESSION STRENGTH INSULATION AT EACH HANGER POINT. INSULATION MAY BE HALF ROUND OR FULL ROUND AND EXTEND 2" BEYOND GALVANIZED SHIELD EACH WAY. I H H I WATER PIPING HANGER THERMAL EXPANSION TANK SUPPORTED FROM STRUCTURE OR ON FLOOR VACUUM RELIEF VALVE CHECK VALVE (TYP) / '4u -r -LA n TEMPERING VALVE 4" HIGH GALVANIZ PAN W/ DRAIN. ELECTRIC WATER HEATER GALVANIZED SHIELD V IYL.71 r%u 1 CHANNEL fON [PE CUTOFF VALVE (TYP) -THERMOMETER ASME TEMP. & PRESS. RELIEF VALVE PIPE FULL SIZE TO AUXILLARY DRAIN PAN. HOSE BIBB DRAIN VALVE DRAIN LINE, PIPE FULL SIZE TO INDIRECT DRAIN CONNECTION. GENERAL PLUMBING NOTES 1. EQUIPMENT AND MATERIALS SPECIFIED AND/OR SHOWN ON DRAWINGS SHALL BE FURNISHED (EXCEPT AS NOTED) COMPLETELY INSTALLED, ADJUSTED, AND SHALL BE LEFT IN A SAFE AND SATISFACTORY OPERATING CONDITION. ALL ACCESSORIES, PARTS, AND CONNECTIONS NECESSARY FOR THE OPERATION OF THE EQUIPMENT SHALL BE FURNISHED AND INSTALLED. 2. ALL MATERIALS, EQUIPMENT, AND APPARATUS SHALL BE NEW EXCEPT ITEMS THAT ARE CALLED FOR AS BEING REUSED OR FURNISHED BY &HERS. 3. ALL EXISTING LOCATIONS ARE TAKEN FROM EXISTING DRAWINGS. IT WILL BE WITHIN THE CONTRACTOR'S SCOPE OF WORK TO VERIFY EXISTING SERVICES AND THE EXACT LOCATION OF PIPES, TO MAKE ALL OFFSETS; AND TO ADD NEW PIPING SYSTEMS TO THE EXISTING PIPING SYSTEMS AS PART OF THE PROJECT CONTRACT. 4. CONTRACTOR SHALL CONNECT WATER AND WASTE PIPING TO EQUIPMENT FURNISHED BY THE OWNER OR IN ANOTHER DIVISION OF THIS CONTRACT AS REQUIRED FOR COMPLETE OPERATION. 5. MAKE ALL OFFSETS REQUIRED AS PER JOB CONDITIONS. 6. CONTRACTOR SHALL COORDINATE AT SITE WITH EXISTING STRUCTURE AND OTHER TRADES BEFORE INSTALLATION OF PLUMBING WORK. 7. THE CONTRACTOR SHALL KEEP A SET OF MARKED UP DRAWINGS AS THE JOB PROGRESSES. NO MAJOR CHANGE SHALL BE MADE TO PLUMBING DESIGN/ENGINEERING UNLESS IT HAS BEEN COORDINATED, DRAWN, AND SUBMITTED FOR APPROVAL TO THE ARCHITECT. 8. CONTRACTOR SHALL BE RESPONSIBLE FOR ANY DAMAGE TO EXISTING PIPING, FIXTURES OR EQUIPMENT DUE TO NEW CONSTRUCTION AND HE SHALL RESTORE EXISTING WORK TO ITS ORIGINAL CONDITION AT NO COST TO THE OWNER. 9. ALL PLUMBING WORK SHALL BE PERFORMED IN ACCORDANCE WITH THE FLORIDA BUILDING CODE, 2007 EDITION WITH THE 2009 SUPPLIMENTS AS WELL AS LOCAL ORDINANCES AND IN COMPLIANCE WITH THE ENERGY CONSERVATION CODE. 10. CONTRACTOR SHALL FURNISH AND INSTALL SHOCK ABSORBERS ON PIPING SERVING FIXTURES AND EQUIPMENT WITH QUICK CLOSING VALVES. SIZE OF SHOCK ABSORBERS SHALL BE ACCORDING TO PDI STANDARDS. 11. CONTINUITY OF SERVICES: EXISTING BUILDING WILL REMAIN IN USE DURING CONSTRUCTION OPERATIONS. WHEN AN INTERRUPTION OF AN EXISTING SERVICE IS NECESSARY, CONTRACTOR SHALL COORDINATE WITH AUTHORIZED HOSPITAL PERSONNEL BEFORE MAKING THE NECESSARY INTERRUPTION. 12. ALL PENETRATIONS THROUGH WALLS AND FLOORS SHALL BE SLEEVED AND/OR PATCHED AS DIRECTED BY THE SPECIFICATIONS. PATCHING SHALL MATCH EXISTING FINISH. (SEE ARCH. DRAWINGS). 13. CONTRACTOR SHALL PROVIDE TRAP PRIMERS ON ALL NEW FLOOR DRAINS NOT RECEIVING CONSTANT DISCHARGE FROM FIXTURES AND/OR EQUIPMENT, OR AS REQUIRED BY STATE AND LOCAL CODES. 14. ALL VENT TERMINALS SHALL BE A MINIMUM OF 25'-0" AWAY FROM A/C AIR INTAKES, WINDOWS AND DOORS. PLUMBING LEGEND SYMBOL DESCRIPTION SYMBOL DESCRIPTION - COLD WATER BALL VALVE -- HOT WATER BALANCING VALVE (B.V.) — --- HOT WATER RECIRCULATION 4- CHECK VALVE (C.V.) — — • — — COLD WATER (BELOW FLOOR) P-1,ETC FIXTURE INDENTIFICATION W WASTE OR SOIL PIPING CAP ON END OF PIPE --V-- VENT PIPE CONNECTION TO EXISTING CD CONDENSATE DRAIN PIPE TURNED UP PIPE TURNED DOWN PLUMBING ABBREVIATIONS COLD WATER F.D. FLOOR DRAIN HOT WATER R.P.B.P. REDUCED PRESS. BACKFLOW PREY. [H.W. . HOT WATER RECIRC A.F.F. ABOVE FINISHED FLOOR VENT C.O. CLEANOUTABOVE CEILING WASTE W.C.O. WALL CLEANOUT . VENT THRU ROOF F.C.O. FLOOR CLEANOUT PLUMBING EQUIPMENT SCHEDULE SYSTEM TYPE MFGR. MODEL EWT LWT STORAGE FLOW TANK REMARKS NO. CAPACITY RECOVERY SIZE EWH-1 ELEC A.O.SMITH DEN-80 60 140 80 51GPH @ 800 24" x 0 V, 1 PH, kW GAL. RISE 60"H 9.0 kW TOTAL. (DUAL DUAL ELEMENT - E EWH-2 SIMULTANEOUS) ET-1 2.1 THERMAL EXPANSION TANK: - AMTROL ST-5-C - GAL. MAX. ACCEPTANCE VOLUME: ET-2 0.9 GALLON 3/4" SYSTEM CONNECTION TV-1 THERMOSTATIC SYMMONS 5-230-CK-M-X - 115 TEMPERING VALVE, TV-2 ASME 1017 RATED. DRAWING INDEX NUMBER TITLE P0.1 SCHEDULES, LEGEND, NOTES & DRAWING INDEX P1.1 PLUMBING PLAN - NEW CONSTRUCTION PINES,@ - US Project No. 10006.01 Pool $DATE$ $TIME$ $FILEA$ 02010 BHIP%Architects, Inc.