|
A. Installation shall be in strict accordance with manufacturer s shop drawings. Pcrtlalcr attention should be given to protecting the
<br />finish during handling aid erection.
<br />33 GLEANIN6
<br />A. After installation, entire system shall be left In a clean condition.
<br />SECTION 123623 - PLASTIC COWERTOP5
<br />ID 6ENERAL
<br />1.1 SECTION REQUIREMENTS
<br />A. 5uhanitta15: Shop Drawings, Samples showing the full range of colas, textures, ad pattern available for each type of finish aid
<br />AM Quality Certification Program certificates.
<br />B. Fabricator Gluallfications: Certified participant In AWI's auallty certification Program.
<br />G. Installer auallf"lons: Fabricator of products.
<br />D. Environmental Limitations: Do not deliver or install countertops until building Is enclosed, wet work is completed, aid HVAG system
<br />Is operating.
<br />2.0 PROVXT5
<br />2.1 PLN5TIG-LAMINATE GOUNTERTOP5
<br />A. Quality Standard: AWI, AWAG, and WI'5 "Architectural Woodwork Standards."
<br />B. Plastic -Laminate Gountertops: Premium or Custom grade.
<br />I. Laminate Grade: H65 for flat countertops, F16P for post -formed countertops
<br />2. 6rain Direction: Parallel to cabinet fronts.
<br />3. Edge Treatment: Sane as laminate cladding on horizontal surfaces.
<br />22 MATERIALS
<br />A. Wood Moisture Content: 5 to 10 percent.
<br />B. Medium -Density Fiberboard: AN51 A2082, Grade 130, made with binder containing no urea formaldehyde.
<br />G. Particleboard: ANSI A208.1, Grade M-2, made with binder containing no urea formaldehyde.
<br />D. Softwood Plywood: DOG P5 I.
<br />E. HgHlresure Decorative Laminate: NEMA L.D 3.
<br />I. Manufacturers:
<br />a. Wlisonart International: Div. of Premark International, Inc.
<br />b. or Approved equal.
<br />F. 6rortmets for Gable Passage through Countertops: 2 hah O.D., moldedoostic grommets and matchhg plastic caps with slot for
<br />were passage.
<br />I. Product:
<br />a. 2= Mockett d cornier .. Inc. - 06 or 56 series.
<br />5.0 EXECUTION
<br />3.1. FABRICATION
<br />A. Complete fabrication to maximum extent possible before shipment to Project site. Disassemble components only as necessary for
<br />shipment and installation. Where necessary for fitting at site, provide ample allowance for scribing, tanning, and fitting.
<br />32 INSTALLATION
<br />A. Before Installation, condition countertops to average prevailing humidity condition In Installation areas.
<br />B. Install countertops to comply with referenced quality standard for grade specified.
<br />G. Install contertops level, plumb, true and straight. Shin as required with concealed shims. Install level and plumb to a tolerance of
<br />I/8 Inch in 96 Inches.
<br />D. Scribe ad cut countertops to fit adjoining work, refinish cut surfaces, ad repair damaged finish at cuts.
<br />E. Anchor countertops securely to base units. Seal space between backsplash ad wall.
<br />SECTION 12:3W - 5TONE COMTERTOP5
<br />ID GENERAL
<br />1.1 SECTION REGIUIRENENT5
<br />A. Submittals: Shop Drawings and Stone Samples at least 12 Inches (300 run) square.
<br />B. Verify dimensions of stone countertops by field cements and indicate on Shop Drawings.
<br />2.0 PRODUCTS
<br />2.1 STONE
<br />A. Granite: ASTM G 615
<br />I. Description: Lhiform, fine-grained, stone.
<br />2. Varletles and Sources: Product per drawings.
<br />3. Finish: Polished.
<br />22 5ETING MATERIALS
<br />A. Watery -Gleanable Epoxy Adhesive: AN51 AII83.
<br />I. Manufacturers: One of the following:
<br />a. Bonsal. W.R. Gomoarnl.
<br />b. Bonstone Materials Corporation.
<br />c. G Gore•
<br />d. Custom Bulldha Products.
<br />e. Laticrete International. Inc.
<br />f. MAPEI Coro.
<br />B. Sealant: Mildew -resistant, neutral -curing, silicone sealant.
<br />G. Stone Sealer: Colorless, stain -resistant sealer that does not affect color or physical properties of stone surfaces, as
<br />recommended by stone producer For application kdlcated.
<br />I. Manufacturers: One of the following:
<br />a. Bostlk FIndlq Inc.
<br />b. Gustam Eiulldha Products
<br />c. Hillyard. Inc.
<br />d. HMK Stone Care 5pkin.
<br />e. Miracle Sealants Gompg%
<br />f. Stone Gore International. Inc.
<br />2.3 COUNTERTOP FABRICATION
<br />A. Comply with recommendations In MIA's "Dimensional Stone - Design Manual VI."
<br />1. Thi imss: 1-1/4 inches (30 man).
<br />2. Edge Detail: Straight, slightly eased at top, I-1/4 Inch (30 nwO bullnose, or 3/8 Inch (10 nW radius with 2-1/2 Inch apron, location
<br />vary per plan.
<br />B. Splashes: 3/4 Inch (20 nW nominal thickness backsplashes and and splashes.
<br />I. Height: 7 Inches, unless noted otherwise.
<br />2. Top -Edge Detail: Straight, slightly eased at corner.
<br />G. Fabricate molded edges Nth machines having abrasive shaping wheels made to reverse contour of edge profile. Form corners of
<br />molded edges as indicated with outside corners slightly eased.
<br />D. Seams: Fabricate countertops without seams, preferred, but for joining in field, with seams 1/16 (15 mm) In width.
<br />E. Cutouts and Holes:
<br />1. Umdercarnter Fixtures: Make cutouts for undercomter Fixtures In shop using template or pattern furnished by fixture manufacturer,
<br />Form cutouts to smooth, even curves.
<br />a. Edge Detall: Vertical, slkjntly eased at top ad bottom surfaces and projecting 3/16 inch (5 rrm) into fixture opening.
<br />2. Gounter-Mounted Fixtures: Prepare countertops in shop for field cutting openings for counter -wonted fixtures. Mark tops for
<br />cutouts ad drill holes at corners of cutout locatlore. Make caner hales of largest radius practical.
<br />3. Fittings: Drill countertops In ship for plumbing fittings, undercounter soap dispensers, aid similar items.
<br />3.0 EXECUTION
<br />3.1 INSTALLATION
<br />A. Install countertops over plywood s(btops with a full spread of water -cleanable epoxy adhesive.
<br />B. Space seans with 1/16 inch 05 mm) gap for filling with grout sealant. Use temporary shins to ensure uniform spacing ad use clarps
<br />to eliminate lipping.
<br />G. Complete cutouts not finished in shop. Mask areas of countertops adjacent to cutouts while cutting.
<br />D. Install backsplash ad end splashes by adhering to wall with water -cleanable epoxy adhesive. Leave 1/16 Inch (15 mm) gap between
<br />countertop ad splash for filling with sealant. Use temporary shins to ensure uniform spacing.
<br />E. Grout seams to comply with AN51 A108.I0. Tool grout uniformly ad smoothly with plastic tool.
<br />F. Apply sealant to seams and to gap between countertops and splashes.
<br />32 GLEANING
<br />A. Glean countertops as work progresses. Remove adhesive, grout, mortar, and sealant smear Immediately.
<br />B. Glean stone countertops not less than six days after completion of sealant Installation, using clean water ad soft rags. Do not use
<br />materials or methods that could damage stone.
<br />G. Apply stone sealer to comply with stone producer's ad sealer nnanufactu er's written Instructions.
<br />U)
<br />W
<br />U
<br />O
<br />U)
<br />N
<br />ARCHITECTURE
<br />ENGINEERING
<br />3680 Pleasant Hill Road
<br />Suite 200
<br />Duluth, Georgia 30096
<br />p 770.622.9858
<br />f 770.622.9535
<br />www.hillfoleyrossi.com
<br />© Copyright (as dated below).
<br />This drawing and an reproductions thereof are the
<br />property of Hill Foley Rossi & Associates, LLC.(HFR).
<br />It is intended for the sole use of the project named
<br />hereon. Reproduction without the written consent of
<br />FIFR is unlawful. All copies are to be returned to I*R
<br />upon project completion.
<br />1 sealed: 02-13-2019 1
<br />LL
<br />CL
<br />W
<br />N
<br />W
<br />C
<br />_CU
<br />tf
<br />^U
<br />W
<br />Cn
<br />^E
<br />\W
<br />0
<br />L
<br />E
<br />Q�
<br />L
<br />-0 r
<br />4: O
<br />U �
<br />a L
<br />�O
<br />C N ff
<br />(U Z C :E CDCU Cp
<br />C
<br />N N
<br />_ - W
<br />L
<br />LL_
<br />For
<br />02/13/19 Construction
<br />mk I date I issue
<br />Specifications
<br />'ll
<br />HFR 18.945
<br />
|