Laserfiche WebLink
TOi\A — <br />EXTERIOR <br />PLASTER ON <br />FRAME <br />12 <br />14.0 <br />--— — — — — — - <br />TEXTURED <br />CEMENTITIOUS <br />FINISH ON <br />CMU (TYP) <br />12 <br />4.0[— <br />OFF RIDGE <br />12 <br />_ 15.0 <br />35-SH <br />FIBEREGLASS SHINLGE INSTALLED <br />AS PER MANUFACTURER <br />SPECIFICATIONS <br />-LA .......................... 1---F <br />60685CD REAR ELEVATION - B <br />CJ <br />SCALE: 1/4" = V-0" <br />9'-0" RIDGE VENT <br />CJ <br />12 <br />— 15.0 <br />FIBEREGLASS SHINLGE INSTALLED <br />AS PER MANUFACTURER <br />SPECIFICATIONS <br />— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — <br />000 <br />— <br />-------ICJ -------------------------------- CJ/WEEP----------------------------------------- <br />TEXTURED <br />CEMENTITIOUS <br />FINISH ON CMU (TYP) RIGHT ELEVATION - B <br />SCALE: 1/4" = V-0" <br />General Notes <br />ROOF CRITERIA: <br />• 12" OVERHANG U.N.O. <br />• PLUMB CUT FASCIA ROOF <br />• PITCH PER ELEVATION <br />**G.C. VERIFY ROOF PITCH** <br />ROOF PITCH VARIES PER SUBDIVISIONS IT IS THE <br />CONTRACTORS RESPONSIBILITY TO VERIFY <br />ROOF SLOPE REQUIREMENTS WITH TRUSS <br />MANUFACTURER. <br />**ELECTRICAL SPECIFICATION NOTES** <br />ELECTRICAL CONTRACTOR MUST VERIFY WITH <br />THE SPECIFICATIONS FOR THE TYPE OF FIXTURE <br />TO BE USED. LIGHT FIXTURES SHOWN ARE FOR <br />LOCATION PURPOSES. <br />Exterior Covering <br />R703.7 Exterior Plaster. <br />Installation of these materials shall be in compliance with ASTM <br />C926 and ASTM C1063, or ASTM C1787 and the provisions of <br />this code. <br />R703.7.1 Lath. <br />Lath and Lath attachments shall be of corrosion -resistant <br />materials. Expanded metal or woven wire lath shall be attached <br />with 1-1/2" long, 11 gage nails having <br />a 7/16" head, or 1-1/2" long, 16 gage staples, spaced in <br />accordance with ASTM C1063 or C1787, or as otherwise <br />approved. (Refer to sheet SN1 for the engineered method for <br />Lath attachment.) <br />Lathing Accessories <br />Attachments shall be of corrosion -resistant materials. <br />Wood Application: 16 Ga.x1-1/2" long (3/4"-V crown) staples @ <br />6" O.C. vertically/horizontally into the framing members. <br />Masonry Application: Concrete stub nail, 3/8" (10 mm) head dia. <br />min. @ 6" O.C. vertically/horizontally or compatible adhesives, <br />exterior gun -grade, construction adhesive with 1" dabs @ 6" O.C. <br />or in a semi -continuous bead between the solid plaster base and <br />the solid portion of the key attachment flange. <br />Control Joints: Install control joint lathing accessories in <br />conformance with C1063. Lath shall not be continuous through <br />control joints, but shall be stopped and tied at each side. <br />All accessories shall be in accordance with the latest ASTM <br />C1063 & ASTM C1861. <br />R703.7.2 Plaster. <br />Plastering with cement plaster shall be not less than three coats <br />where applied over any type of code -approved lath and shall be <br />not less than two coats where directly applied over masonry, <br />concrete, clay brick, stone, or tile. If the plaster surface is <br />completely covered by veneer or other facing material or is <br />completely concealed, plaster application need be only two coats, <br />provided total thickness is as set in Table R702.1(1). <br />Cement plaster shall be in accordance with ASTM C926 and <br />material shall be in accordance with one of the types listed in <br />R703.7.2. <br />R703.7.3 Water -Resistive Barriers. <br />Water -resistive barriers shall be installed as required in Section <br />R703.2 and, where applied over wood -based sheathing, shall <br />include a water -resistive vapor -permeable barrier with a <br />performance at least equivalent to two layers of Grade D paper. <br />The individual layers shall be installed independently such that <br />each layer provides a separate continuous plane and any flashing <br />(installed in accordance with Section R703.4) intended to drain to <br />the water -resistive barrier is directed between the layers. <br />R703.2 Water -Resistive Barrier. <br />One layer of No. 15 asphalt felt, free from holes and breaks, <br />complying with ASTM D226 for Type 1 felt or other approved <br />water -resistive barrier shall be applied over studs or sheathing of <br />all exterior walls. No. 15 asphalt felt shall be applied horizontally, <br />with the upper layer lapped over the lower layer not less than 2 <br />inches. Where joints occur, felt shall be lapped not less than 6 <br />inches. Other approved materials shall be installed in accordance <br />with the water -resistive barrier manufacturer's installation <br />instructions. The No. 15 asphalt felt or other approved <br />water -resistive barrier material shall be continuous to the top of <br />walls and terminated at penetrations and building appendages in <br />a manner to meet the requirements of the exterior wall envelope <br />as described in Section R703.1. <br />R703.4 Flashing. <br />Approved metal flashing, vinyl flashing, self -adhered membranes <br />and mechanically attached flexible flashing shall be applied <br />shingle -fashion or in accordance with the manufacturer's <br />instructions. Metal flashing shall be corrosion resistant. <br />Fluid -applied membranes used as flashing shall be applied in <br />accordance with the manufacturer's instructions. All flashing shall <br />be applied in a manner to prevent the entry of water into the wall <br />cavity or penetration of water to the building structural framing <br />components. <br />Self -adhered membranes used as flashing shall comply with <br />AAMA 711. All exterior fenestration products shall be sealed at <br />the juncture with the building wall with a sealant complying with <br />AAMA 800 or ASTM C920 Class 25 Grade NS or greater for <br />proper joint expansion and contraction, ASTM C1281, AAMA 812, <br />or other approved standard as appropriate for the type of sealant. <br />Fluid -applied membranes used as flashing in exterior walls shall <br />comply with AAMA 714. The flashing shall extend to the surface <br />of the exterior wall finish. <br />Approved flashings shall be installed at the following locations. <br />• Exterior window/door openings. <br />• Intersection of chimneys or other masonry construction with <br />frame walls. <br />• Under and at the ends of masonry, wood or metal copings <br />and sills. <br />• Continuously above all projecting wood trim. <br />• Where exterior porches, decks or stairs attach to a wall or <br />floor assembly of wood -frame construction. <br />• At wall and roof intersection. <br />• At Built-in gutters. <br />Coastal Flashings <br />All flashing material for coastal locations (ex: within 3,000 feet of the <br />ocean) shall be corrosion resistant material (ex: zinc and/or stainless <br />steel) and shall be selected for compatibility with adjacent wood <br />preservatives per the manufacturer's recommendations. <br />REV. 09.24.21 <br />cv <br />N <br />00 <br />= <br />c14 <br />c� <br />CD <br />s <br />M <br />X <br />(9 b a- <br />N O CO <br />r <br />61 6f <br />> E C <br />d <br />10 <br />d <br />a <br />_ E <br />o <br />O- v <br />O <br />0`0 W N <br />CC�'• d' <br />U �O o <br />•��•' <br />'9F1` <br />V✓//OF E S S\O <br />��l'flrl�i91i11ti\ <br />To the best of the Engineer's knowledge, information and belief, <br />the structural plans and specifications contained within these <br />drawings comply with the 2020 <br />Florida Building Code - <br />Residential 7th Edition. Engineer's <br />signature and seal is only for <br />the structural engineering portions <br />of the drawing pages bearing <br />Engineers signature and seal. <br />U, <br />W <br />F� <br />APAQ <br />o E <br />o co 3 <br />0 0 <br />N N <br />W N <br />0? ti <br />In <br />C/) <br />M <br />Q <br />t7 <br />MV 2'�LL <br />Co S J <br />C J 52 W W <br />W <br />m c v o <br />�CUo13 �o <br />W <br />9 N <br />o� °'. <br />W <br />Z <br />NLW <br />ILW <br />Ch °' m w <br />- coLO Z Q J <br />J <br />;n <br />Z <br />OU L) o <br />❑ <br />Z N M <br />O O <br />O <br />Z � N <br />z o � <br />J — <br />a ,T, <br />U <br />N <br />Q) <br />Cn o <br />Q <br />LU <br />U <br />0 <br />L/711 <br />\/N <br />LU o <br />c w <br />rJ <br />Nis <br />F_ <br />_ p <br />i <br />ii' <br />w N <br />II <br />U o °n <br />c m 0 <br />¢ <br />�® <br />o <br />CD <br />CD <br />M <br />Cl)O <br />z z <br />5 <br />z <br />a <br />g <br />U_ <br />E E <br />C 0 <br />s� <br />z0 <br />as <br />co <br />t� <br />—o <br />X O <br />O <br />'zU<O QE <br />ro <br />L <br />¢ z <br />Co� <br />aWN <br />m <br />Z <br />10 <br />OZ <br />ZY <br />Q) <br />J <br />N m <br />0� <br />Q W <br />ZO <br />f <br />U) <br />o¢ <br />go <br />a <br />w� <br />�W <br />w <br />'O <br />o <br />co <br />v <br />0< <br />a� <br />.o <br />cC:) <br />> ^ ' <br />�.► / <br />N <br />I..L <br />O <br />0 <br />m <br />ca <br />m <br />0 <br />(� <br />co <br />r <br />0 <br />_ <br />0 <br />: <br />L / <br />CM <br />N <br />O <br />00 N <br />� <br />r <br />Q <br />r <br />� o <br />j <br />M r <br />00 <br />o <br />Z <br />f6 <br />Z <br />E T- <br />m <br />y <br />`m <br />a- <br />E <br />U � <br />Q p <br />c <br />� <br />JOB <br />NO: <br />22-09402 <br />SCALE : <br />AS NOTED <br />SHEET NO. <br />2.2 <br />