|
63
<br />*I
<br />OUTLM SPECIFICATIONS
<br />8 OPENINGS
<br />8 OPENINGS (CONTINUED)
<br />_____
<br />9 FINISHES (CONTRNMED) —
<br />9 FINISBES (CONTINUED)
<br />1
<br />I 0 SPECIALTIES (CONTINUED) - -_
<br />8.01 HOLLOW METAL DOORS AND FRAMES
<br />8.04 HARDWARE
<br />9.02 TILE
<br />9.07 FIBERGLASS REINFORCED PLASTIC PANELS (FRP):
<br />10.05 STORAGE UNIT SYSTEMS
<br />GENERAL: COMPLY WITH ANSI A250.8/SDI 100.
<br />GENERAL: SUBMIT PRODUCT DATA AND HARDWARE SCHEDULE FOR REVIEW
<br />GENERAL: MAINTAIN MINIMUM TEMPERATURE OF 50 DEGREES F DURING
<br />GENERAL: PROVIDE FfBERGLA AND MAXIMUM SMOKE DEVELOPED INDEX OF 450
<br />GENERAL: PROVIDE STORAGE UNIT SYSTEMS BY JANUS INTERNATIONAL
<br />SUBMITTALS: SUBMIT PRODUCT DATA AND SHOP DRAWINGS FOR REVIEW.
<br />BEFORE ORDERING HARDWARE.
<br />INSTALLATION, AND FOR 7 DAYS AFTER COMPLETION. PROTECT TILE FROM FOOT
<br />(ASTM E84). MAINTAIN TEMPERATURE AND HUMIDITY RANGE RECOMMENDED BY
<br />CORPORATION, OR APPROVED SUBSTITUTE. PROTECT ALL SHARP OR UNFINISHED
<br />HARDWARE: PROVIDE HARDWARE AS SCHEDULED BY MANUFACTURER INDICATED,
<br />TRAFFIC FOR MINIMUM 7 DAYS AFTER INSTALLATION.
<br />MANUFACTURER FOR AT LEAST 48 HOURS BEFORE, DURING AND AFTER
<br />EDGES WITH PROTECTIVE COVERS OR BY HEMMING, AND COVER ALL EXPOSED
<br />HOLLOW METAL FRAMES: FABRICATE FRAMES FROM MINIMUM 16 GAUGE
<br />OR APPOVED SUBSTITUTE.
<br />SUBMITTALS: SUBMIT PRODUCT DATA FOR REVIEW.
<br />INSTALLATION.
<br />FASTENER TIPS WITH PLASTIC COVERS. PROVIDE METAL REINFORCEMENT OR
<br />COLD -ROLLED STEEL (ASTM A1008). PREPARE FRAMES TO RECEIVE MORTISED AND
<br />KEYING: PROVIDE 6-PIN CYLINDERS FOR ALL LOCKS. RE -KEY ALL LOCKS AT
<br />SUBMITTALS: SUBMIT PRODUCT DATA FOR REVIEW.
<br />BACKING FOR ALL SURFACE MOUNTED EQUIPMENT, INCLUDING EQUIPMENT
<br />CONCEALED HARDWARE AND REINFORCE FRAMES TO RECEIVE SURFACE APPLIED
<br />CERAMIC FLOOR TILE: ANSI A 137. 1, MOISTURE ABSORPTION LESS THAN 0.50% (ASTM
<br />PROVIDED BY OTHERS. INSTALL IN ACCORDANCE WITH THE MANUFACTURER!S
<br />14ARDWARE IN ACCORDANCE WITH ANSI A250.6. MAKE PROVISIONS FOR
<br />END OF CONSTRUCTION IN MASTERKEY SYSTEM AS DIRECTED BY OWNER.
<br />C373), D.C.O.F. EQUAL TO OR EXCEEDING 0.42 (ANSI A137.1-2012 SECTION 9);
<br />FIBERGLASS REINFORCED PLASTIC PANELS: FIBERGLASS REINFORCED
<br />INSTRUCTIONS.
<br />INSTALLATION OF ELECTRICAL ITEMS. PREPARE FRAMES TO RECEIVE 3 SILENCERS
<br />PROVIDE OWNER WITH 8 MASTERKEYS AND 2 CHANGE KEYS FOR EACH LOCK.
<br />MANUFACTURER, PRODUCT, AND COLOR AS SCHEDULED. PROVIDE MATCHING
<br />THERMOSETTING POLYESTER RESIN SHEETS (ASTM D5319),0.090" TfUCK x 4'WIDE x
<br />ON STRIKE JAMB W14ERE INDICATED. PROVIDE MIND" 2 FLOOR ANCHORS AND 6
<br />INSTALLATION: INSTALL HARDWARE IN ACCORDANCE WITH THE
<br />TRIM PIECES WHERE INDICATED.
<br />HEIGHT INDICATED; MANUFACTURER, PRODUCT, TEXTURE AND COLOR AS
<br />SUBMITTALS: SUBMIT SHOP DRAWINGS FOR REVIEW.
<br />JAMB ANCHORS FOR ALL FRAMES.
<br />MANUFACTURER'S INSTRUCTIONS AND TO COMPLY WITH GOVERNING
<br />CERAMIC WALL TILE: ANSI A 137.1, MOISTURE ABSORPTION LESS THAN 0.50% (ASTM
<br />SCHEDULED. PROVIDE MANUFACTURER'S MATCfHNG PVC TRIM.
<br />EXTERIOR COILING DOORS: "MODEL 750" MANUALLY OPERATED OVERHEAD
<br />EXTERIOR AND MASONRY OPENINGS: FACE WELDED FRAMES WITH WELDS
<br />REGULATIONS. SET UNITS PLUMB, LEVEL, AND TRUE TO LINE AND LOCATION.
<br />AND COLOR AS SCHEDULED. PROVIDE
<br />INSTALLATION: PREPARE SUBSTRATES AND INSTALL PANELS IN ACCORDANCE
<br />COILING DOOR WITH WIND LOCKS, 26 GAUGE CORRUGATED CURTAIN FABRICATED
<br />GROUND SMOOTH, FABRICATED FROM GALVANNEALED STEEL (ASTM A653
<br />REINFORCE SUBSTRATES AS REQUIRED FOR PORPER INSTALLATION AND
<br />MATCHING TRIM PIECES WHERE INDICATED.
<br />WITH THE MANUFACTURER!S INSTRUCTIONS. ACCLIMATE PANELS IN CONDITIONED
<br />FROM GALVANIZED STEEL, PAINTED FINISH IN COLOR AS SCHEDULED, EXTERIOR
<br />CLASS A60); "SU SERIES" STEEL FRAMES BY CECO DOOR, OR APPROVED
<br />OPERATION, AND DRILL AND COUNTERSINK UNITS THAT ARE NOT PREPARED FOR
<br />SPACE FOR MINIMUM 48 HOURS BEFORE INSTALLATION. SET PANELS PLUMB, LEVEL
<br />LIFT HANDLE(S) ON BOTTOM BAR.
<br />SUBSTITUTE.
<br />ACHORAGE FASTENERS. ADJUST HARDWARE TO PROVIDE UNENCUMBERED
<br />503, MINIMUM ABRASIVE HARDNESS OF 10 (ASTM
<br />AND STRAIGHT, WITH RECOMMENDED GAP BETWEEN PANELS TO ACCOMMODATE
<br />LATCH: STAINLESS STEEL; JANUS MINI LOCK.
<br />OPERATION.
<br />C24 1). FABRICATED AS INDICATED OR AS REQUIRED TO PROVIDE TRANSITION
<br />EXPANSION. ADHERE TO SUBSTRATE WITH MANUFACTURER!S RECOMMENDED
<br />INTERIOR NON -MASONRY OPENINGS: FACE WELDED FRAMES WITH WELDS
<br />BETWEEN ADJOINING FINISH SURFACES AT DOORWAYS.
<br />LOW-VOC LATEX BASED ADHESIVE, AND ATTACH WITH MANUFACTURER!S
<br />FLORIDA PRODUCT APPROVAL NUMBER: 21450.3.
<br />GROUND SMOOTH; "SU SERIES" STEEL FRAMES BY CECO DOOR, OR APPROVED
<br />SUBSTITUTE.
<br />8.05 GLASS
<br />TRANSITION STRIP: EXTRUDED ALUMINUM PROFILE FOR CERAMIC TILE TO
<br />RECOMMENDED FASTENERS. APPLY MOLDINGS TO ALL PANEL JOINTS AND EDGES.
<br />IMPACT RESISTANT EXTERIOR COILING DOORS: "MODEL 850" MANUALLY OPERATED
<br />GENERAL: COMPLY WITH REQUIREMENTS OF ASTM E1300, GLASS PRODUCT
<br />FINISHED CONCRETE TRANSITION, MAXIMUM 1/2" HEIGHT, ADA COMPLIANT, CLEAR
<br />APPLY MANUFACTURER'S RECOMMENDED SILICONE SEALANT TO ALL MOLDINGS
<br />OVERHEAD COILING DOOR, 24 GAUGE CORRUGATED CURTAIN FABRICATED FROM
<br />CONTRACTOR!S OPTION FOR INTERIOR NON -MASONRY OPENINGS LESS
<br />MANUFACTURERS, GANA GLAZING MANUAL, AND GANA LAMINATED GLAZING
<br />ANODIZED FINISH; "RENO-U" BY SCHLUTER SYSTEMS, OR APPROVED SUBSTITUTE.
<br />AND CHANGES IN MATERIAL FOR WATERTIGHT INSTALLATION. REMOVE EXCESS
<br />GALVANIZED STEEL, PAINTED FINISH IN COLOR AS SCHEDULED, EXTERIOR LIFT
<br />THAN 37" WIDE: KNO,CKED-DOWN SLIP-ON DRYWALL TYPE FRAMES WITH
<br />"DU
<br />REFERENCE MANUAL. FOR SAFETY GLAZING COMPLY WITH CPSC 16 CFR PART 1201
<br />WATERPROOFING/CRACK ISOLATION MEMBRANE: SfNGLE-COMPONENT
<br />SEALANT, AND CLEAN PANELS AS RECOMMENDED.
<br />HANDLE(S) ON BOTTOM BAR.
<br />INTERLOCKING MITERED CORNERS; SERIES" STEEL FRAMES BY CECO
<br />DOOR, OR APPROVED SUBSTITUTE.
<br />AND ANSI Z97.1
<br />SELF -CURING LIQUID RUBBER POLYMER (ANSI Al 18.10 AND ANSI Al 18.12).
<br />9.08 PAINTING
<br />LATCH: STAINLESS STEEL; JANUS MINI LOCK.
<br />HOLLOW METAL DOORS: FABRICATE DOORS FROM MINIMUM 16 GAUGE
<br />PERFORMANCE REQUIREMENTS: PROVIDE GLASS LITES IN MINIMUM THICKNESS
<br />TO COMPLY WIT14 ASTM E1300, BUT NOT LESS THAN THE THICKNESS AND
<br />MORTAR BOND COAT: LATEX-PORTLAND CEMENT MORTAR (ANSI Al 18.4).
<br />GENERAL: DELIVER ALL PAINTING MATERIALS IN SEALED, ORIGINAL LABELED
<br />FLORIDA PRODUCT APPROVAL NUMBER: 12765.9.
<br />COLD -ROLLED STEEL (ASTM A 1008), WITH BEVELED EDGES, INVERTED C14ANNEL
<br />STRENGTH INDICATED OR REQUIRED TO WITHSTANDING DESIGN WIND LOADS
<br />GROUT: POLYMER MODIFIED CEMENT GROUT (ANSI A 1 18.7); MANUFACTURER AND
<br />CONTAINERS BEARING MANUFACTURERS NAME, PRODUCT DESCRIPTION, COLOR
<br />DESIGNATION, AND APPLICATION INSTRUCTIONS. PROTECT PRODUCTS FROM
<br />EXTERIOR DOOR PIERS AND HEADERS: FLUSH PANELS FABRICATED FROM MINIMUM
<br />REINFORCEMENT TOP AND BOTTOM, AND FULL FLUSH CONSTRUCTION. REINFORCE
<br />DOORS TO RECEIVE HARDWARE IN ACCORDANCE WITH ANSI A250.6.
<br />INDICATED, THERMAL MOVEMENT RESULTING FROM AMBIENT AND SURFACE
<br />COLOR AS SCHEDULED.
<br />FREEZING. APPLY PAINT ONLY WHEN THE RELATIVE HUMIDITY IS BELOW 85%, AND
<br />16 GAUGE HOT -DIP GALVANIZED STEEL, WITH PAINTED FINISH IN COLOR AS
<br />TEMPERATURE CHANGES, AND IMPACT LOADS.
<br />SEALANT: AT CONTROL JOINT LOCATIONS, PROVIDE TWO -COMPONENT, NON -SAG
<br />THE AMBIENT AIR AND SUBSTRATE TEMPERATURES WILL BE BETWEEN 50 AND 95
<br />SCHEDULED.
<br />VERTICAL EDGE SEAMS: VIS113LE INTERLOCKED EDGE SEAMS, EPDXY FILLED.
<br />WIND-BORNE DEBRIS IMPACT RESISTANCE: COMPLY WITH TAS 201, TAS 202,
<br />POLYURETHANE SEALANT COMPLYING WITH ASTM C920 TYPE S, GRADE NS, CLASS
<br />DEGREES F DURING AND FOR 24 HOURS FOLLOWING APPLICATION.
<br />INTERIOR COILING DOORS: "MODEL 650" MANUALLY OPERATED OVERHEAD
<br />EXTERIOR OPENINGS: IMPACT RESISTANT DOORS FABRICATED FROM
<br />TAS 203, ASTM E 1 866, AND ASTM E 1996 LARGE MISSILE IMPACT TEST FOR
<br />25, USE NT, M, A, G, AND 0; PECORA "DYNAFLEX", OR APPROVED SUBSTITUTE. PRIME
<br />SUBMITTALS: SUBMIT PRODUCT DATA FOR REVIEW.
<br />COILING DOOR, 26 GAUGE CORRUGATED CURTAIN FABRICATED FROM GALVANIZED
<br />GALVANNEALED STEEL (ASTM A653 CLASS A60), WITH STEEL STIFFENERS,
<br />OPENINGS WITHIN 30 FEET OF GRADE, AND SMALL MISSILE IMPACT TEST
<br />SUBSTRATES AS RECOMMENDED, AND INSTALL OVER PLASTIC FOAM BACKER ROD
<br />STEEL, PAINTED FINISH IN COLOR AS SCHEDULED, EXTERIOR LIFT HANDLE(S) ON
<br />CLOSURE AT TOP EDGE, 1.8 LB/CF DENSITY FOAMED IN PLACE POLYURETHANE
<br />FOR OPENINGS MORE TIIAN 30 FEET ABOVE GRADE.
<br />OR BOND BREAKER TAPE.
<br />PAINT: PROVIDE PAINT PRODUCTS INDICATED IN COLORS AS SCHEDULED;
<br />BOTTOM BAR.
<br />CORE, MAXIMUM U-VALUE = 0.36 (ASTM C 1363), MAXIMUM AIR INFILTRATION
<br />"TRIO-E"
<br />SUBMITTALS: SUBMIT PRODUCT DATA FOR REVIEW.
<br />INSTALLATION: INSTALL TILE IN ACCORDANCE WITH REFERENCED STANDARDS
<br />S14ERWIN-WILLIAMS COMPANY UNLESS OTHERWISE INDICATED, OR APPROVED
<br />SUBSTITUTE. PROVIDE PRIMERS AND UNDERCOATS PRODUCED BY THE SAME
<br />LATCH: ZINC COATED STEEL; JANUS MINI LATCH, WITH CYLINDER LOCK.
<br />RATE OF 0. I CFM/SF (ASTM E283); BY CECO DOOI�, OR APPROVED
<br />SUBSTITUTE.
<br />WARRANTIES: MANUFACTURER'S STANDARD WARRANTY TO REPLACE THE
<br />AND THE MANUFACTURER'S INSTRUCTIONS. ACCURATELY CUT AND FIT TILE,
<br />WITHOUT MARRING VISIBLE SURFACES. LAY TILE IN GRID PATTERN UNLESS
<br />MANUFACTURER AS FINISH COATS, AND THAT ARE COMPATIBLE WITH ONE
<br />COILING DOOR ELECTRIC OPERATOR: "PANTHEON" DRUM MOUNTED LOW VOLTAGE
<br />FLORIDA PRODUCT APPROVAL: FL4553. 1.
<br />FOLLOWING PRODUCTS DURING THE PERIOD INDICATED DUE TO
<br />OTHERWISE INDICATED, SET WITH UNIFORM JOINT WIDTHS, AND ALIGN BASE
<br />ANOTHER AND T14E SUBSTRATES INDICATED.
<br />DC MOTOR OPERATOR, UL 325 COMPLIANT CONTROLLER WITH UPIDOWN/STOP
<br />DETERIORATION, INCLUDING PEELING, DISCOLORATION, VISION OBSTRUCTION,
<br />JOINTS WITH FLOOR JOINTS WHERE TILE ARE SAME SIZE. PROVIDE TILE EXPANSION
<br />INSTALLATION: PREPARE SURFACES AND APPLY PAINT IN ACCORDANCE WITH THE
<br />OPERATION AND KEYED SWITCH, ELECTRONIC LIMITS, SOFT START AND SOFT STOP,
<br />INTERIOR OPENINGS: DOORS FABRICATED WITH KRAFT HONEYCOMB BONDED
<br />14ERMATIC SEAL FAILURE, AND DELAMINATION:
<br />JOINTS ALIGNED WITH EXPANSION AND CONTROL JOINTS IN SUBSTRATE, AND
<br />MANUFACTURER!S INSTRUCTIONS. APPLY PAINT ONLY WHEN AMBIENT
<br />AND MANUAL RELEASE FOR MANUAL OPERATION.
<br />CORE; "REGENT" BY CECO DOOR, OR APPROVED SUBSTITUTE.
<br />COATED GLASS PRODUCTS: 10 YEAR WARRANTY.
<br />INSTALL SEALANT FOR JOINTS SUBJECT TO MOVEMENT.
<br />TEMPERATURE AND RELATIVE HUMIDITY ARE WITHIN MANUFACTURER'S
<br />HALLWAY SYSTEM: PROVIDE RELATED HOT -DIP GALVANIZED FRAMING,
<br />FINISHES: SHOP PRIME DOORS AND FRAMES WITH MANUFACTURER!S STANDARD
<br />INSULATING GLASS: 10 YEAR WARRANTY.
<br />FLOOR TILE: INSTALL OVER INTERIOR CONCRETE SUBSTRATE IN ACCORDANCE
<br />RECOMMENDED RANGE. CLEAN SUBSTRATES OF SUBSTANCES THAT COULD IMPAIR
<br />CHANNELS, ANGLES, HARDWARE, AND FASTENERS. COVER ALL GYPSUM BOARD,
<br />BAKED -ON RUST -INHIBITIVE PRIMER IN ACCORDANCE WITH ASNI A250.3 AND
<br />LAMINATED GLASS: I 0 YEAR WARRANTY.
<br />WITH TCA METHOD F-122, WITH WATERPROOFING/CRACK ISOLATION
<br />BOND OF PAINTS, INCLUDING DUST, DIRT, OIL, GREASE, AND INCOMPATIBLE
<br />FIREPROOFING, PIPES, WIRES, AND CONDUITS EXPOSED IN CORRIDORS AND
<br />A250. I 0, COMPATIBLE WITH SUBSTRATE AND FIELD APPLIED COATINGS.
<br />ANNEALED FLOAT GLASS: ASTM C1036, TYPE 1, CLASS I (CLEAR) OR CLASS 2
<br />MEMBRANE (AI08.13), LATEX-PORTLAND CEMENT BOND COAT (ANSI A108.5),
<br />PAINTS. UNIFORMLY APPLY COATINGS TO ACHIEVE MANUFACTURER!S
<br />LOBBIES WITH HALLWAY PANELS TO THE HEIGHT OF THE HALLWAY SYSTEM.
<br />INSTALLATION: INSTALL DOORS AND FRAMES IN ACCORDANCE WITH ANSI A250.11
<br />(TINTED) AS INDICATED, QUALITY q3. PROVIDE MINIMUM 6.0 mm THICKNESS UNLESS
<br />AND POLYMER MODIFIED CEMENT GROUT (ANSI A108.10).
<br />RECOMMENDED DRY FILM THICKNESS, WITHOUT RUNS, DRIPS, SAGS, OR BRUSH
<br />MARKS. APPLY ADDITIONAL COATS WHEN UNDERCOATS, STAINS, OR OTHER
<br />DOOR PIERS AND HEADERS: FLUSH PANELS FABRICATED FROM MINIMUM 20
<br />AND ANSI A I 15.1G. SET FRAMES PLUMB, LEVEL, STRAIGHT, AND SQUARE, AND
<br />OTHERWISE INDICATED OR REQUIRED.
<br />WALL TILE: INSTALL OVER COATED GLASS MAT GYPSUM BACKER BOARD IN
<br />CONDITIONS SHOW THROUGH FINAL COAT, UNTIL PAINT FILM IS OF UNIFORM
<br />GAUGE HOT -DIP GALVANIZED STEEL, WITH PAINTED FINISH IN COLOR AS
<br />A Mrl4f)Q QPrTT_Vlr7l V fkj D"rV r_DfllT'r T A IkA-DQ IXT A4 A Cn'KTDV rn-KjQT'V I TPrrfn,kj
<br />SCHEDULED.
<br />. .
<br />INSTALL DOORS TO ALIGN WITH FRAMES, WITH UNENCUMBERED OPERATION AND
<br />UNIFORM CLEARANCES OF 1/8" AT HEAD AND JAMBS, AND 3/4" AT SILL UNLESS
<br />OTHERWISE INDICATED. INSTALL FIRE RATED DOORS AND FRAMES IN
<br />ACCORDANCE WITH NFPA 80. INSTALL SMOKE AND DRAFT CONTROL DOOR
<br />ASSEMBLIES IN ACCORDANCE WITH NFPA 105 AND NFPA 80.
<br />8.02 ALUMINUM STOREFRONTS AND ENTRANCES
<br />GENERAL: SUBMIT SHOP DRAWINGS AND PRODUCT DATA FOR REVIEW. FIELD
<br />VERIFY ROUGH OPENING DIMENSIONS BEFORE FABRICATION.
<br />PERFORMANCE REQUIREMENTS: PROVIDE STOREFRONT SYSTEMS THAT
<br />COMPLY WITH PERFORMANCE REQUIREMENTS INDICATED:
<br />WIND LOADS: SYSTEMS, INCLUDING ANCHORAGE, CAPABLE OF
<br />WITHSTANDING DESIGN WIND LOADS INDICATED.
<br />DEFLECTION: MAXIMUM ALLOWABLE DEFLECTION OF L/175 @ 25 PSF
<br />STATIC AIR DESIGN LOAD (ASTM E330) FOR MULLIONS UP TO 13'-6", AND
<br />L/240 + 1/4" FOR MULLIONS BETWEEN 13'-6" AND 40'-O".
<br />THERMAL MOVEMENT: ACCOMMODATE 180 DEG F SURFACE TEMPERATURE
<br />WITH NO BUCKLING STRESS ON GLASS, JOINT SEAL FAILURE, OR
<br />PERFORMANCE REDUCTION.
<br />AIR INFILTRATION: MAXIMUM AIR INFILTRATION RATE OF 0.06 CFM/SF @ 6.24
<br />PSF STATIC AIR PRESSURE DIFFERENTIAL (ASTM E283).
<br />WATER PENETRATION: NO WATER LEAKAGE @ 8 PSF STATIC AIR PRESSURE
<br />DIFFERENTIAL (ASTM E33 1).
<br />THERMAL TRANSMITTANCE FOR THERMALLY BROKEN FRAMING: MAXIMUM
<br />SYSTEM U-FACTOR OF 0.47 GLASS TO EXTERIOR WITH LOW-E GLASS (AAMA
<br />1503).
<br />CONDENSATION RESISTANCE FACTOR (CRF) FOR THERMALLY BROKEN
<br />FRAMING: MR41MUM CRF OF 70 GLASS TO EXTERIOR FOR FRAME WITH
<br />LOW-E GLASS (AAMA 1503).
<br />MATERIALS AND FABRICATION: FABRICATE STOREFRONTS AND ENTRANCES FROM
<br />EXTRUDED ALUMINUM COMPLYING WITH ASTM B221, 6063 T-5 OR 6063 T-6 ALLOY
<br />AND TEMPER. ALUMINUM SHEET TO COMPLY WITH ASTM B209,5005-HI4 FOR
<br />ANNODIZED FINISH AND 3003-1114 FOR PAINTED FINISH. PROVIDE MANUFACTURER!S
<br />RECOMMENDED FASTENERS, REINFORCING MEMBERS, ANCHORS, CLIPS,
<br />ACCESSORIES, AND SEALANTS. FABRICATE UNITS WITH UNIFORM HAIRLINE JOINTS
<br />LOCATED ONLY AT INTERSECTION OF MEMBERS, SECURED AND SEALED. CONCEAL
<br />WELDS IN ACCORDANCE WITH AWS RECOMMENDATIONS. PREPARE AND
<br />REINFORCE FRAMES AND DOORS TO RECEIVE HARDWARE IN ACCORDANCE WITH
<br />THE MANUFACTURER!S INSTRUCTIONS.
<br />STOREFRONT FRAMING SYSTEMS:
<br />INTERIOR STOREFRONT FRAMING SYSTEM: CENTER GLAZED TO ACCEPT 1/4"
<br />GLASS, FACE DIMENSIONS OF 1-3/4" x 4".
<br />MANUFACTURER AND PRODUCT: "TRIFAB 400" BY KAWNEER COMPANY,
<br />INC., OR APPROVED SUBSTITUTE.
<br />THERMALLY BROKEN STOREFRONT FRAMING SYSTEM: THERMALLY BROKEN,
<br />CENTER GLAZED TO ACCEPT UP TO V INSULATING GLASS, FACE DIMENSIONS OF
<br />2" x 4-1/2".
<br />MANUFACTURER AND PRODUCT: "TRIFAB VG 45 1 T" BY KAWNEER COMPANY,
<br />INC., OR APPROVED SUBSTITUTE.
<br />FLORIDA PRODUCT APPROVAL NUMBER: FL 1 0008. 1.
<br />ALUMINUM ENTRANCES:
<br />MEDIUM STILE SWING DOORS: STILE WIDTH OF 3-1/2", TOP RAIL WIDTH OF 3-1/2",
<br />AND BOTTOM RAIL WIDTH OF I 0". CAPABLE OF ACCEPTING UP TO V GLASS.
<br />MAXIMUM AIR INFILTRATION RATE FOR SINGLE DOOR OF 0.50 CFM/SF @ 1.57 PSF
<br />STATIC AIR PRESSURE DIFFERENTIAL (ASTM E283). PROVIDE MANUFACTURER!S
<br />STANDARD HARDWARE AS SCHEDULED.
<br />MANUFACTURER AND PRODUCT: "350 SWING DOOR" BY KAWNEER
<br />COMPANY, INC., OR APPROVED SUBSTITUTE.
<br />FLORIDA PRODUCT APPROVAL NUMBER: FL 10388. 1.
<br />FINISH: CLEAR ANODIC COATING COMPLYING WITH AA-MIOC21A31, AAMA 611,
<br />ARCHITECTURAL CLASS 11.
<br />INSTALLATION: INSTALL ALUMINUM STOREFRONT FRAMING AND ENTRANCE
<br />DOORS IN ACCORDANCE WITH THE MANUFACTURER!S INSTRUCTIONS. SET
<br />STOREFRONT FRAMING PLUMB, LEVEL, TRUE -TO -LINE, AND SQUARE, WITH
<br />HAIRLINE JOINTS AND WITHOUT DISTORTION OR IMPEDING THERMAL MOVEMENT.
<br />PROVIDE INDICATED FLASHINGS AND COVERS TO MATCH FINISH OF ALUMINUM
<br />FRAMING. PROVIDE EXTRUDED SILL FLASHING WITH END DAMS AT EXTERIOR
<br />SYSTEMS, SET IN BED OF SEALANT, AND WITH PENETRATING FASTENERS SEALED.
<br />SEPARATE ALUMINUM FROM CORROSIVE MATERIALS. ENSURE CONDENSATION OR
<br />WATER PENETRATING JOINTS DRAIN TO EXTERIOR, AND ANCHOR SECURELY IN
<br />PLACE. INSTALL DOORS TO ALIGN WITH FRAMES, WITH UNENCUMBERED
<br />OPERATION AND UNIFORM CLEARANCES.
<br />8.03 AUTOMATIC SLIDING ENTRANCES
<br />GENERAL: SUBMIT SHOP DRAWINGS AND PRODUCT DATA FOR REVIEW. FIELD
<br />VERIFY ROUGH OPENING DIMENSIONS BEFORE FABRICATION.
<br />PERFORMANCE REQUIREMENTS: PROVIDE TEST REPORTS FROM A QUALIFIED
<br />TESTING FACILITY INDICATING COMPLIANCE WITH THE FOLLOWING:
<br />STRUCTURAL PERFORMANCE: SYSTEM CAPABLE OF WITHSTANDING DESIGN
<br />WIND LOADS INDICATED.
<br />AIR INFILTRATION: MAXIMUM AIR INFILTRATION RATE OF 1.0 CFM/SF @ 1.57
<br />PSF STATIC AIR PRESSURE DIFFERENTIAL (ASTM E283).
<br />AUTOMATIC SLIDING ENTRANCES: AUTOMATIC SLIDING DOOR ASSEMBLY FOR
<br />TWO-WAY TRAFFIC PATTERN IN CONFIGURATION INDICATED. PROVIDE
<br />EMERGENCY BREAKAWAY CAPABILITY FOR SLIDING LEAF(S) AND SfDELIGHT(S)
<br />REQUIRING NOT MORE THAN 50 LBF TO MANUALLY SET IN MOTION, AND
<br />COMPLYING WITH BHMA A 1 56. 1 0. FABRICATE FROM EXTRUDED 6063-T6 ALUMINUM
<br />MEMBERS. PROVIDE MAUNFACTURER!S STANDARD OPERATORS, ELECTRONIC
<br />CES, MOTION AND PRESENCE SENSORS, EMERGENCY
<br />BREAKAWAY FEATURE, SLIDING WEATHERSTRIPPING, DOOR BOTTOM SWEEP, AND
<br />DOUBLE BEVEL ALUMINUM THRESHOLD.
<br />NOMINAL 1-3/4"x4-1/2" FRAME, 2" STILES, 10" BOTTOM RAILS, AND 2"
<br />INTERMEDIATE RAILS.
<br />LOCKING: PROVIDE FIVE POINT LOCKING SYSTEM, WITH DEADBOLT AND FLUSH
<br />BOLTS OPERATED BY EXTERIOR CYLINDER AND INTERIOR THUMB TURN.
<br />PROVIDE ACCESS CONTROL LOCKING SYSTEM FOR INTEGRATION WITH
<br />OWNERS KEYPAD ACCESS SYSTEM, WITH FAIL -SECURE SOLENOID LOCKING
<br />DEVICE, KEYED CONTROL SWITCH, AND KEYED POWER SWITCH.
<br />PRODUCT AND MANUFACTURER: "DURA-STORM 3000 SERIES" BY STANLEY
<br />ACCESS TECHNOLOGIES, OR APPROVED SUBSTITUTE.
<br />MIAMI-DADE COUNTY NOA NUMBER: 17-0828.09.
<br />FINISH: CLEAR ANODIC COATING COMPLYING WITH AA-Ml2C22A3 1, AAMA 61 1,
<br />ARCHITECTURAL CLASS 11.
<br />INSTALLATION: INSTALL IN ACCORDANCE WITH THE MANUFACTURER'S
<br />INSTRUCTIONS. SET ENTRANCE PLUMB, LEVEL, STRAIGHT AND SQUARE, AND
<br />FASTEN SECURELY IN PLACE. ADJUST DOOR OPERATORS, CONTROLS, AND
<br />HARDWARE FOR SMOOTH AND SAFE OPERATION, AND WEATHERTIGHT CLOSURE.
<br />COORDINATE INTEGRATION OF OWNER'S KEYPAD ACCESS SYSTEM.
<br />CLASS 2 (TINTED): "SOLARBRONZE" BY VITRO ARCHITECTURAL GLASS, OR
<br />APPROVED SUBSTITUTE. VISIBLE LIGHT TRANSMITTANCE = 53% AND SHGC =
<br />0.63.
<br />CLASS 2 (TINTED): "SOLARGRAY" BY VITRO ARCHITECTURAL GLASS, OR
<br />APPROVED SUBSTITUTE. VISIBLE LIGHT TRANSMITTANCE = 44% AND SHGC =
<br />0.58.
<br />HEAT TREATED FLOAT GLASS: ASTM C 1048, TYPE 1, CLASS I (CLEAR) OR CLASS 2
<br />(TINTED) AS INDICATED, QUALITY q3, AND KIND AS INDICATED OR REQUIRED.
<br />FABRICATE BY HORIZONTAL ROLLER -HEARTH PROCESS, WITH WAVE DISTORTION
<br />PARALLEL TO BOTTOM EDGE AS INSTALLED. PROVIDE MINIMUM 6.0 mm THICKNESS
<br />UNLESS OTHERWISE INDICATED OR REQUIRED.
<br />KIND HS: PROVIDE BEAT STRENGTHENED FLOAT GLASS WHERE REQUIRED TO
<br />RESIST S14ADING INDUCED THERMAL STRESSES AND IMPOSED LOADS.
<br />KIND FT: PROVIDE FULLY TEMPERED FLOAT GLASS WHERE REQUIRED TO
<br />RESIST SHADING INDUCED THERMAL STRESSES AND IMPOSED LOADS, OR
<br />WHERE SAFETY GLASS IS INDICATED OR REQUIRED (COMPLY WITH CPSC 16 CFR
<br />PART 1201 AND ANSI Z97. 1).
<br />SPANDREL GLASS: COMPLY WITH GANA 89-1-6. PROVIDE MINIMUM 5 MIL DRY
<br />THICKNESS WATER -BASED SILICONE ELASTOMERIC OPACfFIER ON #2 SURFACE OF
<br />TINTED FLOAT GLASS, KIND FT; "OPACI-COAT-300" BY ICD HIGH PERFORMANCE
<br />ED SUBSTITUTE. USE NEUTRAL -CURING SEALANTS AND
<br />SILICONE GASKETS AND SETTING BLOCKS FOR FABRICATION AND INSTALLATION.
<br />LOW-E COATED GLASS: ASTM C1376, FLOAT GLASS WITH METALLIC -OXIDE OR
<br />NITRIDE COATING APPLIED BY VACUUM DEPOSITION PROCESS AFTER
<br />MANUFACTURE, KIND AS INDICATED OR REQUIRED.
<br />FABRICATION: FABRICATE GLAZING UNITS IN ACCORDANCE WITH THE
<br />MANUFACTURER'S INSTRUCTIONS AND REFERENCED GLAZING PUBLICATIONS, TO
<br />COMPLY WITH SYSTEM PERFORMANCE REQUIREMENTS. PROVIDE SEALANTS,
<br />GLAZING TAPES, GASKETS, AND ACCESSORIES THAT HAVE BEEN TESTED FOR
<br />COMPATIBILITY WITH OTHER GLAZING MATERIALS.
<br />INSULATING GLASS UNITS: ASTM E2190. PROVIDE ALUMINUM SPACERS, DUAL EDGE
<br />SEAL WITH POLYISOBUTYLENE PRIMARY AND SILICONE SECONDARY, AND
<br />DESICCANT.
<br />V CLEAR LOW-E INSULATING GLASS UNITS:
<br />OUTBOARD LITE: 6mm CLEAR GLASS, KIND AS INDICATED OR REQUIRED,
<br />WITH LOW-E COATING ON #2 SURFACE; "SOLARBAN 90" BY VITRO
<br />ARCHITECTURAL GLASS, OR APPROVED SUBSTITUTE.
<br />INBOARD LITE: 6mm CLEAR GLASS, KIND AS INDICATED OR REQUIRED.
<br />UNIT PERFORMANCE:VISIBLE, LIGHT TRANSMITTANCE = 5 1 %, SHGC = 0.23,
<br />AND WINTER U-VALUE = 0.29.
<br />1" INSULATING SPANDREL GLASS UNITS:
<br />OUTBOARD LITE: 6mm CLEAR GLASS, KIND AS INDICATED OR REQUIRED.
<br />INBOARD LITE: 6nun CLEAR GLASS, KIND FT, WITH SPANDREL COATING ON
<br />#4 SURFACE; "LAVA BRONZE" SPANDREL COATING BY ICD HIGH
<br />PERFORMANCE COATINGS, OR APPROVED SUBSTITUTE.
<br />INSTALLATION: COMPLY WITH THE MANUFACTURER!S INSTRUCTIONS. INSTALL
<br />GLASS LITES IN SERIES WITH UNIFORM PATTERN, DRAW, AND BOW.
<br />9 FINISHES
<br />9.01 GYPSUM BOARD ASSEMBLIES
<br />GENERAL: PROTECT PRODUCTS FROM EXPOSURE TO WEATHER AND CONTACT WITH
<br />WET SURFACES. DO NOT BEGIN GYPSUM BOARD INSTALLATION UNTIL BUILDING
<br />ENVELOPE IS WATERTIGHT. DO NOT BEGIN TAPING AND FINISHING UNTIL
<br />TEMPERATURE HAS BEEN STABILIZED BETWEEN 50 AND 95 DEGREES F FOR
<br />MR41MUM 48 HOURS.
<br />SUBMITTALS: SLI13MIT PRODUCT DATA FOR REVIEW.
<br />STEEL FRAMING: ASTM C645, GALVANIZED STEEL STUDS, RUNNERS, TRACK, AND
<br />FURRING MEMBERS. SIZE AND SPACING AS INDICATED, MINIMUM METAL
<br />THICKNESS AS REQUIRED BY STEEL FRAMING MANUFACTURER'S PUBLISHED
<br />LIMITING HEIGHT TABLES.
<br />AT WALLS INDICATED TO RECEIVE TILE FINISH, PROVIDE STUDS SPACED 16" O.C.
<br />MAXIMUM WITH MINIMUM METAL THICKNESS AS REQUIRED BY STEEL
<br />FRAMING MANUFACTURER!S PUBLISHED LIMITING HEIGHT TABLES TO LIMIT
<br />DEFLECTION TO L/360, BUT NOT LESS THAN 20 GAUGE.
<br />GYPSUM BOARD: ASTM C1396, MAXIMUM FLAME SPREAD INDEX OF 25 AND
<br />MAXIMUM SMOKE DEVELOPED INDEX OF 450 (ASTM E84), THICKNESS INDICATED,
<br />TAPERED EDGES, REGULAR TYPE FOR WALLS AND SAG -RESISTANT TYPE FOR
<br />CEILINGS. PROVIDE TYPE X OR TYPE C WHERE INDICATED.
<br />PROVIDE GYPSUM BOARD WITH MOISTURE AND MOLD RESISTANT CORE AND
<br />PAPER FACES; "SHEETROCK MOLD TOUGH" BY UNITED STATES GYPSUM
<br />K MOLD -GUARD" BY GEORGIA PACIFIC GYPSUM LLC, OR
<br />APPROVED SUBSTITUTE.
<br />COATED GLASS MAT GYPSUM BACKER BOARD: ASTM C 1 178, MAXIMUM FLAME
<br />SPREAD INDEX OF 15 AND MAXIMUM SMOKE DEVELOPED INDEX OF 5 (ASTM E84),
<br />WATER-RESISTANT GYPSUM CORE PANELS WITH COATED FIBERGLASS MAT
<br />FACINGS, THICKNESS AS INDICATED. PROVIDE AT WALL AREAS INDICATED TO
<br />RECEIVE TILE FINISH. PROVIDE TYPE X OR TYPE C WHERE INDICATED.
<br />SCREWS: ASTM C 1 513, SELF -DRILLING, SELF -TAPPING SCREWS AT STEEL FRAMING.
<br />ASTM C954 OR ASTM C1002 TYPE S OR S-12 BUGLE OR PANCAKE HEAD AT GYPSUM
<br />BOARD TO STEEL FRAMING. PROVIDE CORROSION RESISTANT SCREWS AT COATED
<br />GLASS MAT GYPSUM BACKER BOARD AND CEMENT BACKER BOARD.
<br />JOINT COMPOUND AND TAPE: ASTM C475, READY -MIXED ALL-PURPOUSE
<br />DRYING -TYPE VINYL BASED JOINT COMPOUND, AND 2" PAPER REINFORCING TAPE.
<br />PROVIDE MANUFACTURER'S RECOMMENDED MOLD AND MILDEW RESISTANT
<br />JOINT COMPOUND.
<br />CORNER BEAD AND EDGE TRIM: ASTM C 1 047, ZINC ALLOY FORMED BEAD, L-TRIM,
<br />OR U-TRIM WITH FLANGES FOR CONCEALMENT IN JOINT COMPOUND.
<br />ACOUSTICAL INSULATION: ASTM C655, TYPE 1, CLASS A, UNFACED GLASS FIBER
<br />BATT INSULATION. FRICTION FIT BATTS TO FILL ENTIRE STUD CAVITY.
<br />ACOUSTICAL SEALANT: ASTM C834, NON -SAG, PAINTABLE, NON -STAINING LATEX
<br />SEALANT, TESTED TO REDUCE AIRBORNE SOUND TRANSMISSION (ASTM E90), AND
<br />COMPLYING WITH ASTM E814.
<br />INSTALLATION: COMPLY WITH ASTM C754 FOR STEEL FRAMING INSTALLATION,
<br />ASTM C636 FOR DRYWALL SUSPENSION SYSTEMS, AND ASTM C840 AND GA-216 FOR
<br />GYPSUM BOARD APPLICATION AND FINISHING. AT FIRE RATED ASSEMBLIES,
<br />PROVIDE MATERIALS AND INSTALLATION IDENTICAL TO THOSE LISTED BY UL.
<br />ISOLATE STEEL FRAMING FROM BUILDING STRUCTURE, AND PROVIDE
<br />SUPPLEMENTARY FRAMING AND BLOCKING TO SUPPORT ATTACHED WORK- APPLY
<br />GYPSUM BOARD TO MINIMIZE BUTT JOINTS, WITH END JOINTS STAGGERED
<br />MINIMUM 24". AND SCREW ATTACH TO SUPPORTS. PROVIDE CORNER BEAD AT ALL
<br />EXTERNAL CORNERS, AND EDGE TRIM WHERE BOARDS ABUT OTHER
<br />CONSTRUCTION. EMBED JOINT TAPE AND PAPER FACED METAL TRIM IN JOINT
<br />COMPOUND, THEN APPLY 3 COATS OF JOINT COMPOUND OVER JOINTS, TRIM,
<br />FASTENERS, AND SURFACE DEFECTS, SANDING AFTER EACH COAT AND LEAVING
<br />SURFACE SMOOTH AND FREE OF VISUAL DEFECTS (GA-214 LEVEL 4); EXCEPT APPLY
<br />I COAT AT CONCEALED SURFACES (GA-214 LEVEL 2).
<br />ACCORDANCE WITH TCA MET140D W-245, WITH LATEX-PORTLAND CEMENT
<br />BOND COAT (ANSI A 1 08.5), AND POLYMER MODIFIED CEMENT GROUT (ANSI
<br />A108.10).
<br />9.03 ACOUSTICAL PANEL CEILINGS
<br />GENERAL: PROTECT PRODUCTS FROM EXPOSURE TO WEATHER AND CONTACT WITH
<br />WET SURFACES. DO NOT BEGIN INSTALLATION UNTIL BUILDING ENVELOPE IS
<br />WATERTIGHT, AND TEMPERATURE AND HUMIDITY CONDITIONS HAVE BEEN
<br />STABILIZED AT FINAL OCCUPANCY LEVELS FOR MINIMUM 48 HOURS.
<br />SUBMITTALS: SUBMIT PRODUCT DATA FOR REVIEW.
<br />ACOUSTICAL PANELS: WET FORMED MINERAL FIBER (ASTM E1264, TYPE 111, FORM 2),
<br />MAXIMUM FLAME SPREAD INDEX OF 25 AND MAXIMUM SMOKE DEVELOPED INDEX
<br />OF 50 (ASTM E84), LOW VOC FORMULATION, FOR USE WITH EXPOSED GRID
<br />SUSPENSION SYSTEM AS SCHEDULED; MANUFACTURER, PRODUCT AND COLOR AS
<br />SCHEDULED.
<br />SUSPENSION SYSTEM: ASTM C 635, HEAVY DUTY, DOUBLE -WEB GALVANIZED STEEL
<br />CONSTRUCTION WITH EXPOSED FLANGE ON MAIN BEAMS AND CROSS TEES, FLUSH
<br />FIT CROSS TEES, BAKED POLYESTER PAINT FINISH; MANUFACTURER, PRODUCT AND
<br />COLOR AS SCHEDULED. PROVIDE MANUFACTURER'S MATCHING EDGE MOLDINGS
<br />AND TRIM. SIZE ATTACHMENT DEVICES FOR 5 TIMES DESIGN LOAD INDICATED IN
<br />ASTM C635. PROVIDE MINIMUM 12 GAUGE WIRE FOR HANGERS AND TIES, ASTM
<br />A641, CLASS I ZINC COATING, SOFT TEMPER, PRE -STRETCHED, WITH YIELD STRESS
<br />LOAD AT LEAST THREE TIMES DESIGN LOAD.
<br />INSTALLATION: INSTALL IN ACCORDANCE WITH ASTM C636 AND THE
<br />MANUFACTURER'S INSTRUCTlONS. LAYOUT CEILING GRID AS INDICATED ON
<br />REFLECTED CEILING PLANS. INSTALL WALL MOLDINGS AT INTERSECTION OF
<br />SUSPENDED CEILING AND VERTICAL SURFACES, WITH MITERED CORNERS OR
<br />CORNER CAPS. RABBET EDGES OF REVEAL EDGE PANELS AT BORDER AREAS AND
<br />VERTICAL SURFACES.
<br />9.04 RESILIENT BASE
<br />GENERAL: PROVIDE RESILIENT BASE WITH CRITICAL RADIANT FLUX OF 0.45
<br />WATTS/SQ CM OR GREATER, CLASS I (ASTM E648), AND MAXIMUM SMOKE
<br />DEVELOPED OF 450 (ASTM E662). MAINTAIN TEMPERATURE AND HUMIDITY RANGE
<br />RECOMMENDED BY MANUFACTURER FOR AT LEAST 48 HOURS BEFORE, DURING
<br />AND AFTER INSTALLATION.
<br />SUBMITTALS: SUBMIT PRODUCT DATA FOR REVIEW.
<br />VINYL BASE: THERMOPLASTIC VINYL BASE, ASTM F-1861, TYPE TV, GROUP 2,4"
<br />HIGH x 1/8" GAUGE, COVED PROFILE; MANUFACTURER, PRODUCT AND COLOR AS
<br />SCHEDULED.
<br />INSTALLATION: INSTALL IN LENGTHS AS LONG AS PRACTICAL IN ACCORDANCE
<br />WITH THE MANUFACTURER!S INSTRUCTIONS, USING RECOMMENDED LOW-VOC
<br />ADHESIVE. FIELD FORM OUTSIDE AND INSIDE CORNERS BY SHAVING BACK OF BASE
<br />NO MORE THAN 20% OF THE BASE THICKNESS, AND FOLDING BASE; COPE TOE OF
<br />COVE BASE AT INSIDE CORNERS.
<br />9.05 RESILIENT TILE FLOORING
<br />GENERAL: PROVIDE RESILIENT TILE FLOORING WITH CRITICAL RADIANT FLUX OF
<br />0.45 WATTS/SQ CM OR GREATER, CLASS I (ASTM E648), AND MAXIMUM SMOKE
<br />DEVELOPED OF 450 (ASTM E662). MAINTAIN TEMPERATURE AND HUMIDITY RANGE
<br />RECOMMENDED BY MANUFACTURER FOR AT LEAST 48 HOURS BEFORE, DURING
<br />AND AFTER INSTALLATION.
<br />SUBMITTALS: SUBMIT PRODUCT DATA AND INSTALLATION INSTRUCTIONS FOR
<br />REVIEW.
<br />VINYL COMPOSITION TILE (VCT): ASTM F1066, CLASS 2,12"xl2"xl/8" THICK;
<br />MANUFACTURER, PRODUCT, AND COLOR AS SCHEDULED. INSTALL WITH
<br />MANUFACTURER'S RECOMMENDED ADHESIVE. LAY TILE IN BASKET WEAVE
<br />PATTERN WITH ALTERNATING GRAIN DIRECTION.
<br />ACCESSORIES: PROVIDE PATCHING AND LEVELING COMPOUND AND LOW-VOC
<br />ADHESIVE AS RECOMMENDED BY RESILIENT FLOORING MANUFACTURER. PROVIDE
<br />RESILIENT EDGE/TRANSITION STRIPS TAPERED TO MEET ABUTTING MATERIALS.
<br />INSTALLATION: PREPARE SUBSTRATES AND INSTALL FLOORING IN ACCORDANCE
<br />WITH THE MANUFACTURER!S INSTRUCTIONS. EXAMINE SUBSTRATES FOR DEFECTS
<br />BEFORE BEGINNING INSTALLATION. REMOVE CONCRETE PROJECTIONS AND FILL
<br />LOW SPOTS WITH PATCHING AND LEVELING COMPOUND TO PROVIDE SMOOTH
<br />SURFACE. DO NOT DELIVER FLOORING MATERIALS UNTIL TEMPERATURE AND
<br />HUMIDITY CONDITIONS HAVE BEEN STABILIZED, AND ACCLIMATE FLOORING
<br />MATERIALS IN CONDITIONED SPACE FOR MINIMUM 48 HOURS BEFORE
<br />INSTALLATION. CLEAN SURFACES IMMEDIATELY BEFORE INSTALLING FLOORING.
<br />LAYOUT FLOORING AS INDICATED, OR TO PROVIDE EQUAL WITDH TILES GREATER
<br />THAN RALF-WIDTE AT OPPOSITE ENDS OF SPACES. INSTALL FLOORING BEFORE
<br />INSTALLING FLOOR SET CASEWORK AND EQUIPMENT. EXTEND FLOORING INTO
<br />RECESSES, AND SCRIBE AND CUT TO FIT PERMANENT CONSTRUCTION WHILE
<br />LEAVING RECOMMENDED EXPANSION SPACE. INSTALL RESILIENT EDGE STRIPS AT
<br />EDGES OF FLOORING THAT WOULD OTHERWISE BE EXPOSED. CLEAN RESILIENT
<br />FLOORING AFTER INSTALLATION.
<br />ADHESIVE INSTALLATION: REMOVE DELETTRIOUS COATINGS FROM SUBSTRATE.
<br />TEST SUBSTRATE FOR DRYNESS (ASTM F 1 869 AND ASTM F2170), PH (ASTM F7 I 0)
<br />AND BOND - DO NOT PROCEED WITH INSTALLATION UNTIL RESULTS ARE
<br />ACCEPTABLE. ADHERE FLOORING TO SUBSTRATE.
<br />9.06 CARPET TILE
<br />GENERAL: PROVIDE CARPET TILE WITH CRITICAL RADIANT FLUX OF 0.45 WATTS/SQ
<br />CM OR GREATER, CLASS I (ASTM E648), AND MAXIMUM SMOKE DEVELOPED OF 450
<br />(ASTM E662). MAINTAIN TEMPERATURE AND HUMIDITY RANGE RECOMMENDED BY
<br />MANUFACTURER FOR AT LEAST 48 HOURS BEFORE, DURING AND AFTER
<br />INSTALLATION.
<br />SUBMITTALS: SUBMIT PRODUCT DATA FOR REVIEW.
<br />CARPET TILE: TUFTED TIP -SHEARED CARPET TILE, NYLON, SOLUTION DYED, STAIN
<br />AND ANTI -MICROBIAL TREATED, WITH MANUFACTURER!S STANDARD BACKING;
<br />MANUFACTURER, PRODUCT, AND COLOR AS SCHEDULED.
<br />INSTALLATION: PREPARE SUBSTRATES AND INSTALL CARPET TILE IN
<br />TURER!S INSTRUCTIONS. COMPLY WITH CRI
<br />INDOOR AIR QUALITY INSTALLATION GUIDELINES. ACCLIMATE FLOORING
<br />MATERIALS IN CONDITIONED SPACE FOR MINIMUM 48 HOURS BEFORE
<br />INSTALLATION. TEST CONCRETE SUBSTRATE MOISTURE (ASTM F2170) AND
<br />ALKALINITY, AND DO NOT INSTALL IF RESULTS ARE OUT OF MANUFACTURER'S
<br />RECOMMENDED RANGE. EXAMINE SUBSTRATES FOR DEFECTS BEFORE BEGINNING
<br />INSTALLATION. REMOVE CONCRETE PROJECTIONS AND FILL LOW SPOTS WITH
<br />PATCHING AND LEVELING COMPOUND TO PROVIDE SMOOTH SURFACE. CLEAN
<br />SURFACES IMMEDIATELY BEFORE INSTALLING FLOORING. LAYOUT TILE AS
<br />INDICATED, OR IF NOT INDICATED TO PROVIDE EQUAL WITDH TILES GREATER
<br />THAN HALF -WIDTH AT OPPOSITE ENDS OF SPACES. ADHERE FLOORING TO
<br />SUBSTRATE USING RECOMMENDED LOW-VOC ADHESIVES. BUTT TILES TOGETHER
<br />TIGHTLY TO FORM SEAMS WITHOUT GAPS, AND FIT TIGHTLY TO OBSTRUCTIONS.
<br />PROVIDE RESILIENT EDGE STRIPS AT EDGES OF FLOORING THAT WOULD
<br />OTHERWISE BE EXPOSED. CLEAN AND VACUUM CARPET TILES AFTER
<br />INSTALLATION.
<br />FINISH, COLOR, AND APPEARANCE. UNLESS OTHERWISE INDICATED, PAINT AND
<br />FINISH ALL EXPOSED SURFACES THAT ARE NOT PREFINISHED. DO NOT PAINT CODE
<br />REQUIRED LABELS OR EQUIPMENT PLATES. PROVIDE THE FOLLOWING PAINT
<br />SYSTEMS FOR THE SUBSTRATES AND GLOSS INDICATED:
<br />EXTERIOR MASONRY AND CONCRETE WALLS - PAINTED:
<br />I ST COAT: LOXON CONCRETE & MASONRY PRIMER SEALER (A24W8300)
<br />2ND COAT: A-100 EXTERIOR LATEX SATIN (A82 SERIES)
<br />3RD COAT: A-100 EXTERIOR LATEX SATIN (A82 SERIES)
<br />EXTERIOR ALUMINUM AND GALVANIZED METAL - SEMI -GLOSS:
<br />I ST COAT: SOLO ACRYLIC SEMI -GLOSS (A76 SERIES)
<br />2ND COAT: SOLO ACRYLIC SEMI -GLOSS (A76 SERIES)
<br />EXTERIOR FERROUS METAL - SEMI -GLOSS:
<br />I ST COAT (OMIT IF PRE -PRIMED): PRO-CRYL UNIVERSAL PRIMER
<br />(B66-3 I 0 SERIES)
<br />2ND COAT: SOLO ACRYLIC SEMI -GLOSS (A76 SERIES)
<br />3RD COAT: SOLO ACRYLIC SEMI -GLOSS (A76 SERIES)
<br />INTERIOR FERROUS, ALUMINUM AND GALVANIZED METAL - SEMI -GLOSS:
<br />I ST COAT (OMIT IF PRE -PRIMED): PRO-CRYL UNIVERSAL PRIMER
<br />(B66-3 I 0 SERIES)
<br />2ND COAT: PROMAR. 200 ZERO VO,C LATEX SEMI -GLOSS (1331-2600 SERIES)
<br />3RD COAT: PROMAR 200 ZERO VOC LATEX SEMI -GLOSS (B31-2600 SERIES)
<br />INTERIOR FERROUS, ALUMINUM AND GALVANIZED METAL - FLAT:
<br />I ST COAT (OMIT IF PRE-PRRvIED): PRO-CRYL UNIVERSAL PRIMER
<br />(B66-310 SERIES)
<br />2ND COAT: PROMAR 200 ZERO VOC LATEX FLAT (B30-2600 SERIES)
<br />3RD COAT: PROMAR 200 ZERO VOC LATEX FLAT (1330-2600 SERIES)
<br />INTERIOR GYPSUM BOARD - EGG -SHELL:
<br />I ST COAT: PROMAR 200 ZERO VOC LATEX PRIMER (B28W2600)
<br />2ND COAT: PROMAR 200 ZERO VOC LATEX EG-SHEL (B20-2600 SERIES)
<br />3RD COAT: PROMAR 200 ZERO VOC LATEX EG-SHEL (B20-2600 SERIES)
<br />INTERIOR CONCRETE FLOORS - ACRYLIC SEALER:
<br />I ST COAT: H&C INFUSION WATER -BASED CLEAR SEALER
<br />2ND COAT (WHERE SCHEDULED): H&C INFUSION WATER -BASED CLEAR SEALER
<br />10 SPECIALTIES
<br />10.01 TOILET ACCESSORIES: PROVIDE TOILET ACCESSORIES AS SCHEDULED. SET UNITS
<br />PLUMB, LEVEL, AND TRUE TO LINE. REINFORCE SUBSTRATES AS NECESSARY, AND
<br />USE CONCEALED FASTENING WHERE POSSIBLE.
<br />10.02 FIRE EXTINGUISHERS AND ACCESSORIES
<br />GENERAL: PROVIDE FIRE EXTINGUISHER AT EACH LOCATION INDICATED, AND AT
<br />EACH FIRE EXTINGUISHER CABINET.
<br />SUBMITTALS: SUBMIT PRODUCT DATA FOR REVIEW.
<br />FIRE EXTINGUISHERS: NOMINAL 5 LB MULTI -PURPOSE CHEMICAL FIRE
<br />EXTINGUISHER, 3A-40BC RATED, PAINTED STEEL CYLINDER, "MP5-A" BY LARSEN'S
<br />MANUFACTURING CO., OR APPROVED SUBSTTTUTE. PROVIDE WALL BRACKET FOR
<br />FIRE EXTINGUISHERS AT LOCATIONS WITHOUT CABINETS.
<br />INTERIOR FIRE EXTINGUISHER CABINETS: SEMI -RECESSED WITH 2-1/2" ROLLED
<br />EDGE, STEEL BOX AND DOOR, FULL CLEAR ACRYLIC DOOR, WHITE BAKED ENAMEL
<br />FINISH; "2409-R3 " BY LARSEN'S MANUFACTURING CO., OR APPROVED SUBSTITUTE.
<br />EXTERIOR FIRE EXTINGUISHER CABINETS: SURFACE MOUNTED, ALUMINUM BOX
<br />AND DOOR, FULL CLEAR ACRYLIC DOOR WITH LARSEN-LOC RECESSED HANDLE,
<br />CLEAR ANODIZED FINISH; "AL 2409-SM" BY LARSEN'S MANUFACTURING CO., OR
<br />APPROVED SUBSTITUTE.
<br />INSTALLATION: INSTALL IN ACCORDANCE WITH THE MANUFACTURER'S
<br />INSTRUCTIONS. MOUNT CABINETS WITH BOTTOM AT 27" ABOVE FINISH FLOOR. SET
<br />UNITS PLUMB, LEVEL, AND SQUARE.
<br />AT EXTERIOR LOCATIONS, PROVIDE 1/4" SPACER BETWEEN CABINET AND
<br />EXTERIOR WALL.
<br />10.03 BOLLARD COVERS: 1/8" THICK POLYETHYLENE COVERS WITH DOMED TOPS
<br />DESIGNED TO FIT STANDARD STEEL PIPE BOLLARDS; "BOLLARDGARD" BY
<br />fNNOPLAST, OR APPROVED SUBSTITTE. INSTALL IN ACCORDANCE WITH THE
<br />MAUNFACTURER'S INSTRUCTIONS.
<br />COLOR: SAFETY YELLOW.
<br />10.04 KEY LOCK BOX: UL LISTED KEY LOCK BOX, 1/4" STEEL WELDED HOUSING, 1/2" STEEL
<br />DOOR WITH GASKET AND STAINLESS STEEL HINGE, INTERIOR GASKET, BIASED CUT
<br />KEY LOCK WITH DUST COVER, AND INTERFACE FOR BUILDING ALARM SYSTEM;
<br />"KNOXBOX 3200" BY KNOX COMPANY, OR APPROVED SUBSTITUTE. INSTALL IN
<br />ACCORDANCE WITH T14E MAUNFACTURER!S INSTRUCTIONS.
<br />SIZE: 5"x4"0" DEEP.
<br />MOUNTING: RECESSED, WITH STEEL SHELL AND T'0" FLANGE.
<br />COLOR: ALUMINUM.
<br />HALLWAY PANELS: CORRUGATED PANELS FABRICATED FROM MINIMUM 26
<br />GAUGE HOT -DIP GALVANIZED STEEL, WITH PAINTED FINISH IN COLOR AS
<br />SCHEDULED. INSTALL VERTICALLY WITH MID -SPAN BRACING.
<br />HALLWAY BASE: 12" HIGH x 0.080" THICK ALUMINUM DIAMOND PLATE BASE
<br />(ASTM B209 3003-1122) WITH RUBBER CAP AT ALL STORAGE CORRIDOR HALLWAY
<br />PANELS AND PIERS.
<br />HALLWAY CORNERS: FABRICATED FROM MINIMUM 20 GAUGE HOT -DIP
<br />GALVANIZED STEEL, WITH PAINTED FINISH TO MATCH HALLWAY PANELS.
<br />PROVIDE 4"x4"x4'HlGH x 0.080" THICK ALUMINUM DIAMOND PLATE CORNER
<br />GUARDS (ASTM B209 3003-H22) WITH RUBBER CAP AT ALL STORAGE CORRIDOR
<br />OUTSIDE CORNERS.
<br />LOBBY WAINSCOT: 48" HIGH x 0.080" THICK ALUMINUM DIAMOND PLATE
<br />WAINSCOT (ASTM B209 3003-H22) WITH RUBBER CAP AT ALL LOBBIES.
<br />UNIT NUMBER PLAQUE: 4"x8" PLAQUE CONFORMING TO OWNER!S SIGNAGE
<br />STANDARDS. COORDINATE NUMBERING WITH OWNER.
<br />UNIT PARTITION SYSTEM: CORRUGATED PANELS FABRICATED FROM MINIMUN 26
<br />GAUGE GALVALUME STEEL SHEET. INSTALL VERTICALLY WITH MID -SPAN
<br />BRACING. PROVIDE RELATED HOT -DIP GALVANIZED FRAMING, CHANNELS, ANGLES,
<br />HARDWARE, AND FASTENERS. COVER ALL GYPSUM BOARD, FIREPROOFING, PIPES,
<br />WIRES, AND CONDUITS EXPOSED IN THE STORAGE UNITS TO THE HEIGHT OF THE
<br />PARTITION SYSTEM.
<br />BURGLAR BARS: 20 GAUGE GALVANIZED STEEL CHANNELS INSTALLED
<br />HORIZONTALLY @ 7" O.C. FROM TOP OF HALLWAY SYSTEM AND ALL EXTERIOR
<br />STORAGE UNIT PARTITIONS TO UNDERSIDE OF THE DECK ABOVE.
<br />10.06 PRE-ENGINEERED ALUMINUM CANOPY SYSTEMS
<br />GENERAL: COMPLY WITH ASCE 7- 1 0 AND APPLICABLE LOCAL CODES FOR
<br />STRUCTURAL LOADS. SUMBIT SHOP DRAWINGS, SEALED BY A PROFESSIONAL
<br />ENGINEER REGISTERED TO PRACTICE IN THE JURISDICTION WHERE THE PROJECT IS
<br />LOCATED, SHOWING COMPLIANCE WITH THE INDICATED STRUCTURAL
<br />REQUIREMENTS WITHOUT EXCEEDING ALLOWABLE WORKING STRESS OF
<br />MATERIALS, INCLUDING ANCHORS AND CONNECTIONS. COMPLY WITH
<br />REQUIREMENTS OF THE ALUMINUM DESIGN MANUAL.
<br />MANUFACTURER: PROVIDE PRODUCTS MANUFACTURERD BY PEACHTREE
<br />PROTECTIVE COVERS, INC., OR APPROVED SUBSTITUTE.
<br />MATERIALS:
<br />INTERLOCKING DECKING, BEAMS AND GUTTERS: EXTRUDED ALUMINUM ALLOY
<br />6063 TEMPER T6, COMPLYING WITH ASTM B221.
<br />FLASHING: MINIMUM 0.040" ALUMINUM.
<br />FASTENERS: STAINLESS STEEL WITH NEOPRENE WASHERS WHERE IN CONTACT
<br />WITH ALUMINUM. HOT -DIP GALVANIZED ANCHORS FOR ATTACHMENT TO
<br />MASONRY OR STEEL.
<br />FABRICATION: FABRICATE TO INDICATED SIZES, DIMENSIONS AND DETAILS.
<br />ASSEMBLE WORK TRUE -TO -LINE, WITH TIGHT, CLOSE FITTING JOINTS. PROVIDE
<br />FULLY WELDED EXTRUDED ALUMINUM SYSTEM, WITH PROVISIONS FOR THERMAL
<br />EXPANSION. EASE EXPOSED EDGES AND GRIND ALL EXPOSED WELDS SMOOTH.
<br />PROVIDE COMPONENTS REQUIRED FOR PROPER ANCHORAGE. SHOP FINISH AS
<br />INDICATED.
<br />FINISH: HIGH PERFORMANCE FLUOROPOLYMER COATING COMPLYING WITH
<br />AAMA 2604, TWO -COAT THERMOCURED SYSTEM OF INHIBITIVE PRIMER AND
<br />FLUOROPOLYMER TOPCOAT CONTAINING MINIMUM 70% PVDF RESIN, MINIMUM
<br />1.2 MIL DRY FILM THICKNESS, COLOR AS SCHEDULED.
<br />INSTALLATION: INSTALL WORK TRUE-TO-LfNE AND PLUMB, WITH SLOPE FOR
<br />POSITIVE DRAINAGE. ANCHOR FABRICATIONS SECURELY IN PLACE WITH
<br />COMPATIBLE FASTENERS. PREVENT CONTACT BETWEEN ALUMINUM AND
<br />DISSIMILAR MATERIALS. PROVIDE FLASHING AT ADJACENT CONSTRUCTION. TEST
<br />DRAINAGE SYSTEM. TOUCH-UP FINISH IMMEDIATELY AFTER ERECTION.
<br />10.07 EXTERIOR SCREENS AND TREILLAGE:
<br />GENERAL: COMPLY WITH ASCE 7-10 AND APPLICABLE LOCAL CODES FOR
<br />STRUCTURAL LOADS. SUMBIT SHOP DRAWINGS, SEALED BY A PROFESSIONAL
<br />ENGINEER REGISTERED TO PRACTICE IN THE JURISDICTION WHERE THE PROJECT IS
<br />LOCATED, SHOWING COMPLIANCE WITH THE INDICATED STRUCTURAL
<br />REQUIREMENTS WITHOUT EXCEEDING ALLOWABLE WORKING STRESS OF
<br />MATERIALS, INCLUDING ANCHORS AND CONNECTIONS. COMPLY WITH
<br />REQUIREMENTS OF THE ALUMINUM DESIGN MANUAL. FIELD VERIFY DIMENSIONS
<br />PRIOR TO FABRICATION.
<br />WALL MOUNTED TRELLIS: "NATURESCREEN SYSTEM" AS MANUFACTURED BY
<br />CITYSCAPES INCORPORATED, OR APPROVED SUBSTITUTE. FABRICATE FRAMES
<br />FROM EXTRUDED ALUMINUM (ASTM B221 ALLOY 6005-T5), MINIMUM 0.063"
<br />THICKNESS AND 3" FACE WIDTH. FABRICATE WIRE MESH PANELS FROM MINIMUM 10
<br />GAUGE STAINLESS STEEL WIRE WELDED AT EACH INTERSECTION IN 4"x4" GRID.
<br />PROVIDE EXTRUDED ALUMINUM WALL MOUNT BRACKETS AND STAINLESS STEEL
<br />FASTENERS WITH NEOPRENE WASHERS FOR ATTACHMENT TO WALL STRUCTURE.
<br />FINISH LOUVERS WITH POWDER COATTNG IN COLOR SCHEDULED (AAMA 2603).
<br />INSTALLATION: INSTALL WORK LEVEL, PLUMB, AND SQUARE, ALIGNED TO
<br />MAINTAIN MODULAR GRID. ANCHOR UNITS SECURELY IN PLACE IN ACCORDACE
<br />WITH THE MANUFACTURER'S INSTRUCTIONS.
<br />-0-LLY
<br />w 0 W U_ v) D W (D W
<br />cr 3: �3 Ll) a- 1;_1 f� Z _j
<br />z z >_ E <
<br />< -i >- W w 0 _j Lu < Z W u
<br />cn -i w I-- U- < m 0-- < w (n
<br />z < ui = If) I- Lu 0 LL_ U �--
<br />0
<br />Ff5 c� ,=) �'-
<br />< co u Q� Z
<br />W ff . = �- < D
<br />< c� Of < c� a- 0
<br />0 -5- z
<br />D cn — U- 0��
<br />Z U) - P 10 0 �_ 0 0 �_ :�
<br />Li- 0
<br />0 LL Z 3: fx co 0 o z m I—
<br />o_
<br />(D zw=�-U)u
<br />ui z �- u w =)
<br />Q� =) :D - LL Z 0<� Ir E >- �W- �3 lo_�
<br />< Lu �- i� �- 0 w cn - z (n U3
<br />oe a- u 0 u 0 c� LL -i = < Z
<br />m 0 w cy ui W u z U- -i 0 U [L 0 0
<br />cr �-- 0- �-- a� z < w z
<br />c
<br />n = = CL Lu
<br />wwu[rUw �__ Z:Ewu�-<
<br />M = 0� uj 0� Q� �_ < z — w = �� �i Q�
<br />�__ �-- < m < CL �;_) 0 o �- > F-- m m
<br />. I
<br />(1)
<br />blo
<br />ct
<br />��
<br />0
<br />-4-i
<br />V�
<br />4_�
<br />r___4 rl::$ �.�
<br />cu C�l
<br />C/) (:) 4-�
<br />611
<br />cn 9?-� En
<br />,j::$ r 0.)
<br />$:� r--o
<br />r_4 . V-4
<br />0 0 g -,- 4
<br />P.� ;-.4
<br />�� �>,
<br />� ;>14�
<br />t� P,
<br />U a)
<br />0 ;_4 N
<br />u P-4
<br />;_�
<br />>_�
<br />rj:�
<br />$:)-�
<br />a)
<br />N
<br />I I I I
<br />w
<br />t I s
<br />J�l
<br />�; -til
<br />a 9 'mm a
<br />wj�u
<br />1 NJ _� Z
<br />��m .j ,6
<br />; I �
<br />- � ,'A. I 1
<br />W6
<br />1; t P i -1
<br />A� 'N N -1,
<br />,
<br />I u I
<br />I I �
<br />1(5 1
<br />1
<br />ISSUE: FOR CONSTRUCTION
<br />I I REVISIONS: I I
<br />PROJECT NUMBER
<br />201812
<br />DATE 4-3-19
<br />1
<br />SHEET NUMBER
<br />A0404
<br />
|