|
THESE DETAILS ARE GENERIC AND
<br />MEANT TO SHOW GENERAL FLASHING
<br />AND WATERPROOFING METHODS TO
<br />BE USED.
<br />3/8" CEMENT
<br />PLASTER
<br />12 MIL DRYLOK
<br />CMU - MASONRY BLOCK
<br />EXTREME
<br />WINDOW
<br />FASTENER
<br />1) SEALANT AT
<br />4) SEALANT JOINT
<br />WINDOW BUCK TO
<br />OUTSIDE EDGE OF
<br />'' MASONRY
<br />WINDOW BUCK
<br />e.
<br />2) SEALANT JOINT
<br />5) SEALANT FROM
<br />INSIDE EDGE OF
<br />WINDOW FRAME
<br />WINDOW BUCK
<br />ACROSS WINDOW BUCK
<br />AND EXTEND TO
<br />WINDOW FRAME
<br />MASONRY
<br />ATTACHED
<br />PER CODE
<br />6) TOOLED SEALANT
<br />REQUIREMENTS
<br />BEAD BRIDGING
<br />CLADDING AND WINDOW
<br />FRAME
<br />3) SEALANT WINDOW FRAME TO
<br />WINDOW BUCKALL THE WAY
<br />AROUND, INCLUDING SILL,
<br />SCS 06_05 CMU INSTALLATION 6 POINT BUCK AND
<br />FENESTRATION INSTALLATION AND INTERFACE
<br />JAMB, SILL AND HEAD DETAIL
<br />APPROVED SHEATHING
<br />APPROVED HOUSEWRAP
<br />STRUCTALATH TWIN TRACK 2.5
<br />3/4" CEMENT PLASTER
<br />12 MIL (min) DRYLOK EXTREME
<br />APPROVED FLASHING TAPE
<br />"V" SEALANT SOCKET WITH
<br />TOOLED APPROVED SEALANT
<br />SCS 06_02 WINDOW FIN INTERFACE WITH
<br />EXTRUDED SHOULDER
<br />WEATHER
<br />RESISITIVE
<br />BARRIER
<br />TAPE
<br />(ASSEMBLED WINDOW)
<br />HEAD FLASHING TIE-IN INSTRUXTI(
<br />1. Cut, fold up & temporarily secure)
<br />resistive barrier above header to allow for
<br />flashing installation
<br />2. Self -adhered flashing plus head flashing under
<br />weather resistive barrier
<br />3. Fold weather resistive barrier back over head
<br />flashing and seal with tape
<br />SELF -ADHERED FLASHING Scale: NTS
<br />FLANGED WINDOW
<br />FLASHING INSTALLATION AFTER WEATHER RESISTIVE BARRIER
<br />EXTERIOR SHEATHING y
<br />REFER TO TECHNICAL
<br />LETTER ON CHEMICAL
<br />COMPATIBILITY
<br />SELF -ADHERED FLASHING
<br />DO NOT FLASH OVER
<br />BOTTOM NAILING
<br />FLANGE
<br />NAILING FLANGE
<br />SELF -ADHERED FLASHING
<br />HALF ROUND WINDOW
<br />SELF -ADHERED FLASHING
<br />PRODUCTS DETAILS
<br />TWO LAYERS OF FELT OR ONE LAYER OF HOUSE WRAP AND
<br />ONE LAYER OF FELT ARE REQUIRED BEHIND STUCCO, FBC
<br />R703.2.1 AND FBCR 703.7.3
<br />Detail Instructions
<br />Refer to the number marked as# in each detail that corresponds to the
<br />numbered items in the list of Instructions below:
<br />1. Install self -adhered flashing in order as shown by numbers
<br />2. Install flashing and weather resistive barrier to form water shedding
<br />laps
<br />3. Self -adhered flashing can be substituted for building paper
<br />4. Split the release paper using the ripcord (Split release on demand,
<br />embedded in the adhesive layer) - for ease of installation and to
<br />minimize scoring cuts
<br />5. Remove all release paper per standard installation instructions and
<br />adhere to substrate using a square piece of flashing material (6" x 6"
<br />Minimum)
<br />6. Fold as shown by arrows
<br />7. Angle of corner may vary, adjust folding of the flashing accordingly to
<br />fit tight to corner
<br />8. Mechanically fasten as necessary
<br />r LNJnINU
<br />SELF -ADHERED FLASHING
<br />DECK JOIST
<br />WEATHER
<br />✓E BARRIER &
<br />2ARILY SECURE
<br />WOOD FRAME CONSTR.
<br />EXTERIOR SELF -ADHERED FLASHIN
<br />SHEATHING BY LAPPING DOWN -�
<br />OVER RIM JOIST AND UP
<br />WALL BY 6 IN.
<br />WEATHER
<br />RESISITIVE
<br />BARRIER SEAL TOPS OF JOIE
<br />UNDER DECKING
<br />(SEE DETAIL WP07)
<br />ED FLASHING
<br />DI
<br />0
<br />SELF -ADHERED FLASHING
<br />rLr�onrrv�a
<br />2x FRAMEWALL
<br />TILE FINISH-
<br />1/2" DUROCK-
<br />8" CMU
<br />4"OR8"CMU
<br />(PER SEAT DEPTH)
<br />FILL WITH GROUT -
<br />SLOPED MUD BED -
<br />VINYL SHOWER PAN
<br />SLOPE
<br />d °
<br />4
<br />s4
<br />WEATHER RESISTIVE
<br />BARRIER
<br />SELF -ADHERED FLASHING
<br />EXTERIOR DOOR WITH DECK - SECTION A
<br />EXTERIOR SHEATHING
<br />3/4"-V BEAD OF CONSTR.
<br />ADHESIVE TO BE APPLIED UNDER
<br />THRESHOLD OF DOOR AND RETURN
<br />UP JAMB 6". USE LIQUID NAIL BRAND
<br />OR EQUAL WEATHER PROOF CAULKING
<br />SECTION -A (SEE DETAIL WP02)
<br />SELF -ADHERED FLASHING -�
<br />1 0
<br />2 SEAL TOPS OF JOISTS
<br />UNDER DECKING
<br />8 (SEE DETAIL WP07)
<br />SELF -ADHERED FLASHING
<br />EXTERIOR DOOR WITH DECK
<br />E
<br />AM
<br />SELF-ADHER
<br />J IVIIIV
<br />Q
<br />1'4" PER PLAN
<br />T-0" PER PLAN
<br />SHOWER SEAT
<br />SELF-ADHERED FLASHING
<br />OUTSIDE CORNER
<br />Q
<br />UJ
<br />to
<br />m
<br />Q
<br />Z
<br />/- DOOR ROUGH OPENING
<br />- 3/4"-1" BEAD OF CONSTR.
<br />ADHESIVE TO BE APPLIED UNDER
<br />THRESHOLD OF DOOR AND
<br />RETURN UP JAMB 6". USE LIQUID
<br />NAIL BRAND OR EQUAL WEATHER
<br />PROOF CAULKING
<br />SELF -ADHERED FLASHING
<br />SUBFLOOR
<br />RIM JOIST
<br />WINDOW UNIT
<br />FLASHING REQUIREMENTS
<br />SLOPE
<br />0.3 in: 12.0 in
<br />R703.1 General. Exterior walls shall provide the building with a weather -resistant exterior wall envelope. The exterior wall envelope shall
<br />(0.6 cm : 30.5 cm)
<br />include flashing as described in Section R703.4. A water -resistive barrier is described as a material behind an exterior wall covering that is
<br />SELF -ADHERED FLASHING
<br />intended to resist liquid water that has penetrated behind the exterior covering from further intruding into the exterior wall assembly. An
<br />exterior wall covering is described as a material or assembly of materials applied on the exterior side of exterior walls for the purpose of
<br />EXTERIOR
<br />providing a weather -resistive barrier, insulation, or for aesthetics, including but not limited to, veneers, siding, exterior insulation and finish
<br />CEMT. FIN.
<br />systems, architectural trim and embellishments such as cornices, soffits, and fascias.
<br />BUILDING PAPER
<br />WIRE LATH
<br />R703.2 Water -resistive barrier. One layer of No. 15 asphalt felt, free from holes and breaks, complying with ASTM D226 for Type 1 felt or
<br />other approved water -resistive barrier shall be applied over studs or sheathing of all exterior walls. Such felt or material shall be applied
<br />horizontally, with the upper layer lapped over the lower layer not less than 2 inches (51 mm). Where joints occur, felt shall be lapped not less
<br />than 6 inches (152 mm). The felt or other approved material shall be continuous to the top of walls and terminated at penetrations and
<br />building appendages in a manner to meet the requirements of the exterior wall envelope as described in Section R703.1,
<br />R703.7.3 Water -resistive barriers shall be installed as required in Section R703.2 and, where applied over wood -based sheathing, shall
<br />include a water -resistive vapor -permeable barrier with a performance at least equivalent to two layers of Grade D paper. The individual
<br />Q
<br />layers shall be installed independently such that each layer provides a separate continuous plane and any flashing (installed in accordance
<br />with Section R703.4) intended to drain to the water -resistive barrier is directed between the layers.
<br />Exception: Where the water -resistive barrier that is applied over wood -based sheathing has a water resistance equal to or greater
<br />SELF -ADHERED FLASHING than that of 60-minute Grade D paper and is separated from the stucco by an intervening, substantially nonwater-absorbing layer or
<br />ZR
<br />CEMT. FINISH SILL/ POTSHELF/ CHIMNEY SHOULDER 1 designed drainage space.
<br />MECHANICALLY FASTEN IF RUBBERIZED RUBBERIZED ASPHALT
<br />NEEDED IN CORNERS ADHESIVE R703.4 Flashing. Approved corrosion -resistant flashing shall be applied shingle -fashion in a manner to prevent entry of water into the wall
<br />INSTALL SELF -ADHERED ASPHALT ADHESIVE
<br />INSTALL
<br />SELF-ADHERED
<br />AMB & HEAD THROUGH SELF -ADHERED cavity or penetration of water to the building structural framing components. Self -adhered membranes used as flashing shall comply with
<br />FLASHIFLASHING, SEE FLASHING SELF -ADHERED FLASHING AAMA 711. All exterior fenestration products shall be sealed at the juncture with the building wall with a sealant complying with AAMA 800 or
<br />FLANGED WINDOW ASTM C920 Class 25 Grade NS or greater for proper joint expansion and contraction, ASTM C1281, AAMA 812, or other approved standard
<br />(SEE DETAIL WPO1) 9 P P J P Pp
<br />SCORED as appropriate for the type of sealant. Fluid -applied membranes used as flashing in exterior walls shall comply with AAMA 714. The flashing
<br />RELEASE PAPER shall extend to the surface of the exterior wall finish. Approved corrosion resistant flashings shall be installed at the following locations:
<br />SELF -ADHERED FLASHING, �`o (BEFORE FOLDING, SCORE 1. Exterior window and door openings. Flashing at exterior window and door openings shall extend to the surface of the exterior wall
<br />RELEASESE finish or to the water -resistive barrier complying with Section 703.2 for subsequent drainage. Mechanically attached flexible flashings
<br />EXTEND A MINIMUM 6"
<br />ADHESIVE AS SHOWN)
<br />VERTICALLY FROM
<br />BOTTOM OF
<br />THRESHOLD
<br />:LF-ADHERED FLASHING
<br />LTCH
<br />IHERED FLASHING
<br />2
<br />I4
<br />5
<br />1
<br />Z g
<br />I -
<br />LU LU PLASTER STOP -
<br />�
<br />W CONTINUOUS BACKER-
<br />U ROD & SEALANT
<br />W LU
<br />X
<br />3:
<br />LU
<br />W° A
<br />W
<br />OAM
<br />SELF -ADHERED FLASHING
<br />INSIDE CORNER
<br />Ground?
<br />FOUNDATION WEEP SCREED
<br />STRIP OF SAF
<br />DRAINAGE PLANE WRB
<br />BOND BREAK WRB
<br />SF LATH
<br />- WRAP DP WRB ONTO
<br />THE VERTICAL
<br />SURFACE TO TOP OF
<br />FLANGE AS AN AIR
<br />BARRIER
<br />�. 3-1/2" INCH FLANGE
<br />THIS GAP IS A RESULT OF
<br />NATURAL SHRINKAGE.
<br />DO NOT SEAL.
<br />DRIP SCREED PLASTIC
<br />ACCESSORY
<br />SOFFIT/CANTILEVER
<br />shall comply with AAMA 712. Flashing at exterior window and door openings shall be installed in accordance with one or more of the
<br />following:
<br />1.1 The fenestration manufacturer's installation and flashing instructions, or for applications not addressed in the fenestration
<br />manufacturer's instructions, in accordance with the flashing manufacturer's instructions. Where flashing instructions or
<br />details are not provided, pan flashing shall be installed at the sill of exterior window and door openings. Pan flashing shall be
<br />sealed or sloped in such a manner as to direct water to the surface of the exterior wall finish or to the water resistive barrier
<br />for subsequent drainage. Openings using pan flashing shall incorporate flashing or protection at the head and sides.
<br />5 1.2. In accordance with the flashing design or method of a registered design professional.
<br />4 1.3. In accordance with other approved methods.
<br />6 1.4 In accordance with FMA/AAMA 100, FMA/ AAMA 200, FMA/WDMA 250, FMA/AAMA/ WDMA 300 or FMA/AAMA/WDMA
<br />400.
<br />7 2. At the intersection of chimneys or other masonry construction with frame or stucco walls, with projecting lips on both sides under
<br />2
<br />stucco copings.
<br />• 3. Under and at the ends of masonry, wood or metal copings and sills.
<br />4. Continuously above all projecting wood trim.
<br />5. Where exterior porches, decks or stairs attach to a wall or floor assembly of wood -frame construction.
<br />6. At wall and roof intersections.
<br />7. At built-in autters.
<br />Water Resistant Barrier
<br />Lath
<br />Sheathing
<br />Stucco
<br />LEGEND
<br />SELF ADHERED FLASHING (SAF) -0 o
<br />DRAINAGE PLANE (DP) WEATHER RESISTANT
<br />BARRIER (WRB) - -
<br />BOND BREAK WEATHER RESISTANT BARRIER -
<br />SELF FURRING (SF) LATH
<br />PLASTER ACCESSORY
<br />SHEATHING,'OSB% PLYWOOD, DENSGLASS
<br />A
<br />TACKER ROD
<br />FINISH
<br />STRUCTURAL FRAMING
<br />STRUCTURAL SHEATHING
<br />STRIP OF SAF
<br />DRAINAGE PLANE WRB
<br />BOND BREAK WRB
<br />SF LATH
<br />THESE DETAILS ARE GENERIC AND MEANT TO SHOW GENERAL
<br />FLASHING AND WATERPROOFING METHODS TO BE USED.
<br />Cement Plaster
<br />in accordance
<br />with ASTMC926
<br />over wood 2nd
<br />floor
<br />Cement
<br />Plaster
<br />over block
<br />1 st floor
<br />7/8" Cement Plaster
<br />in accordance with
<br />ASTMC926
<br />Felt backed metal
<br />lathe in accordance
<br />with ASTMC1063
<br />Building Paper
<br />-7/16" O.S.B.
<br />sheathing
<br />Metal
<br />Flashing
<br />Weep Screed
<br />Installed As Per
<br />Manufact. Specs.
<br />Maintain
<br />Bottom of
<br />Weep Screed
<br />1 1/2"to 2"
<br />Above Roof
<br />Sheathing
<br />Note:
<br />The building paper and metal lath must be
<br />installed over the top of the weep screed.
<br />WEEP SCREED DETAIL
<br />SCALE: NOT TO SCALE
<br />7/8" Cement Plaster
<br />in accordance with
<br />ASTMC926
<br />Felt backed metal
<br />lathe in accordance
<br />with ASTMC1063
<br />Building Paper
<br />7/16" O.S.B.
<br />sheathing
<br />Stampede or similar
<br />cauk bottom
<br />joint only
<br />Weep Screed
<br />Installed As Per
<br />Manufact. Specs.
<br />1/2" Cementitious
<br />Decorative Finish
<br />All inside and
<br />outside corner will
<br />need to be miter
<br />cut and caulked all
<br />butt joints need to
<br />becaulked using
<br />Stampede or sim.
<br />caulk for all
<br />0
<br />0
<br />N
<br />N
<br />N
<br />0
<br />To the best of the Engineer's knowledge, information and belief,
<br />the structural plans and specifications contained
<br />within these
<br />drawings comply with the 2017
<br />Florida Building Code -
<br />Residential 6th Edition. Engineer's signature and seal is only for
<br />the structural engineering portions of the drawing pages bearing
<br />Engineer's signature and seal.
<br />f W
<br />ZS
<br />.
<br />4
<br />U
<br />00 QEco
<br />O V u
<br />N c
<br />a00
<br />N #
<br />N
<br />J
<br />LL
<br />O
<br />IDJ
<br />,�
<br />0
<br />?:..
<br />In
<br />� t` L JJ
<br />N N
<br />W
<br />LL _J CL
<br />LL
<br />.V
<br />".ir
<br />Z
<br />C7 M
<br />J
<br />J LL LL
<br />@q'0'r,
<br />LL1
<br />d LL LL
<br />a �
<br />0of
<br />ag
<br />m o
<br />.5'L-
<br />m O
<br />m -1W
<br />N (p
<br />in2°r,'°
<br />¢ Z a
<br />}: W
<br />Z
<br />co coz°
<br />❑
<br />❑
<br />aoIL
<br />t, Z
<br />OU
<br />_J
<br />❑❑❑
<br />W
<br />V MM
<br />(V M
<br />0
<br />Z o
<br />a �
<br />U)
<br />N
<br />M
<br />z
<br />U s
<br />�
<br />LLL
<br />U
<br />O
<br />L1L g
<br />� w
<br />ec/1
<br />v '
<br />)
<br />U
<br />W �
<br />x�
<br />S w �
<br />U ) y
<br />•
<br />c �' x
<br />n M
<br />® 0
<br />II�
<br />o
<br />W
<br />coh
<br />Cl)
<br />o
<br />Z
<br /><
<br />Q E
<br />E °
<br />oo
<br />Z
<br />Z< o
<br />�
<br />Ze
<br />2°
<br />0°
<br />� 6
<br />_
<br />a�
<br />0
<br />OFi
<br />O E
<br />O
<br />N I_
<br />O
<br />¢Z
<br />U
<br />Z
<br />WZ
<br />5 ro
<br />CJJ �
<br />- ro
<br />�<
<br />oY
<br />U
<br />O
<br />zZ
<br />w
<br />mo
<br />oLL
<br />Z
<br />C
<br />< n
<br />6 W
<br />1 Z
<br />Z
<br />o �
<br />29
<br />g°
<br />2�
<br />U
<br /><�
<br />r
<br />yW
<br />3
<br />C
<br />a x
<br />�U
<br />0?
<br />=
<br />J
<br />6
<br />2
<br />ca
<br />W
<br />ca
<br />co
<br />N
<br />L�..
<br />�
<br />N
<br />Q
<br />(
<br />O
<br />U
<br />C4
<br />~
<br />U
<br />Z
<br />�
<br />r
<br />M
<br />.T�
<br />= r
<br />T
<br />i
<br />r-- N
<br />M
<br />r
<br />E
<br />_
<br />M r
<br />o
<br />z
<br />fQ
<br />Z
<br />�
<br />E O
<br />UJ T
<br />r-
<br />M
<br />cc
<br />IL
<br />E
<br />U �
<br />Q p
<br />JOB
<br />NO :
<br />20-8075
<br />SCALE :
<br />AS NOTED
<br />SHEET NO.
<br />W P
<br />
|