Laserfiche WebLink
0 <br />00 <br />C <br />ac <br />3 TAB SHINGLES. ROOF <br />INSTALLED AS PER <br />MANUF. SPECIFICATIONS <br />Tr)M <br />1'-0" <br />15'-0" RIDGE VENT <br />4' OFFRIDGE VENT <br />EXTENDED <br />OVERHANG TO <br />BE CENTERED <br />ON DOOR <br />12 <br />�5 <br />3 TAB SHINGLES. ROOF <br />INSTALLED AS PER MANUF. <br />SPECIFICATIONS <br />REAR ELEVATION - Al <br />SCALE: 1 /4"=V-0" <br />14'-0" RIDGE VENT <br />12 <br />�5 <br />T.O. M. -- <br />HDR HGT. <br />TEXTURED <br />TEXTURED <br />CEMENTICIOUS <br />FINISH ON C.M.U. CE FINISH <br />ON C.M.U.3'-0" <br />FINISH ON C.M. <br />(TYP.) <br />bo (TYP. ) <br />CD <br />RIGHT ELEVATION - Al <br />General Notes <br />ROOF CRITERIA: <br />• 12" OVERHANG U.N.O. <br />• PLUMB CUT FASCIA ROOF <br />• PITCH PER ELEVATION <br />**G.C. VERIFY ROOF PITCH** <br />ROOF PITCH VARIES PER SUBDIVISIONS IT IS THE <br />CONTRACTORS RESPONSIBILITY TO VERIFY <br />ROOF SLOPE REQUIREMENTS WITH TRUSS <br />MANUFACTURER. <br />**ELECTRICAL SPECIFICATION NOTES** <br />ELECTRICAL CONTRACTOR MUST VERIFY WITH <br />THE SPECIFICATIONS FOR THE TYPE OF FIXTURE <br />TO BE USED. LIGHT FIXTURES SHOWN ARE FOR <br />LOCATION PURPOSES. <br />Exterior Covering <br />R703.7 Exterior Plaster. <br />Installation of these materials shall be in compliance with ASTM <br />C926 and ASTM C1063, or ASTM C1787 and the provisions of <br />this code. <br />R703.7.1 Lath. <br />Lath and Lath attachments shall be of corrosion -resistant <br />materials. Expanded metal or woven wire lath shall be attached <br />with 1-1/2" long, 11 gage nails having <br />a 7/16" head, or 1-1/2" long, 16 gage staples, spaced in <br />accordance with ASTM C1063 or C1787, or as otherwise <br />approved. <br />R703.7.2 Plaster. <br />Plastering with cement plaster shall be not less than three coats <br />where applied over any type of code -approved lath and shall be <br />not less than two coats where directly applied over masonry, <br />concrete, clay brick, stone, or tile. If the plaster surface is <br />completely covered by veneer or other facing material or is <br />completely concealed, plaster application need be only two coats, <br />provided total thickness is as set in Table R702.1(1). <br />Cement plaster shall be in accordance with ASTM C926 and <br />material shall be in accordance with one of the types listed in <br />R703.7.2. <br />R703.7.3 Water -Resistive Barriers. <br />Water -resistive barriers shall be installed as required in Section <br />R703.2 and, where applied over wood -based sheathing, shall <br />include a water -resistive vapor -permeable barrier with a <br />performance at least equivalent to two layers of Grade D paper. <br />The individual layers shall be installed independently such that <br />each layer provides a separate continuous plane and any flashing <br />(installed in accordance with Section R703.4) intended to drain to <br />the water -resistive barrier is directed between the layers. <br />R703.2 Water -Resistive Barrier. <br />One layer of No. 15 asphalt felt, free from holes and breaks, <br />complying with ASTM D226 for Type 1 felt or other approved <br />water -resistive barrier shall be applied over studs or sheathing of <br />all exterior walls. No. 15 asphalt felt shall be applied horizontally, <br />with the upper layer lapped over the lower layer not less than 2 <br />inches. Where joints occur, felt shall be lapped not less than 6 <br />inches. Other approved materials shall be installed in accordance <br />with the water -resistive barrier manufacturer's installation <br />instructions. The No. 15 asphalt felt or other approved <br />water -resistive barrier material shall be continuous to the top of <br />walls and terminated at penetrations and building appendages in <br />a manner to meet the requirements of the exterior wall envelope <br />as described in Section R703.1. <br />R703.4 Flashing. <br />Approved metal flashing, vinyl flashing, self -adhered membranes <br />and mechanically attached flexible flashing shall be applied <br />shingle -fashion or in accordance with the manufacturer's <br />instructions. Metal flashing shall be corrosion resistant. <br />Fluid -applied membranes used as flashing shall be applied in <br />accordance with the manufacturer's instructions. All flashing shall <br />be applied in a manner to prevent the entry of water into the wall <br />cavity or penetration of water to the building structural framing <br />components. <br />Self -adhered membranes used as flashing shall comply with <br />AAMA 711. All exterior fenestration products shall be sealed at <br />the juncture with the building wall with a sealant complying with <br />AAMA 800 or ASTM C920 Class 25 Grade NS or greater for <br />proper joint expansion and contraction, ASTM C1281, AAMA 812, <br />or other approved standard as appropriate for the type of sealant. <br />Fluid -applied membranes used as flashing in exterior walls shall <br />comply with AAMA 714. The flashing shall extend to the surface <br />of the exterior wall finish. <br />Approved flashings shall be installed at the following locations. <br />• Exterior window/door openings. <br />• Intersection of chimneys or other masonry construction with <br />frame walls. <br />• Under and at the ends of masonry, wood or metal copings <br />and sills. <br />• Continuously above all projecting wood trim. <br />• Where exterior porches, decks or stairs attach to a wall or <br />floor assembly of wood -frame construction. <br />• At wall and roof intersection. <br />• At Built-in gutters. <br />Coastal Flashings <br />All flashing material for coastal locations (ex: within 3,000 feet of the <br />ocean) shall be corrosion resistant material (ex: zinc and/or stainless <br />steel) and shall be selected for compatibility with adjacent wood <br />preservatives per the manufacturer's recommendations. <br />N <br />0 <br />N <br />N <br />N <br />�1�E1".tiitcp�rt <br />o <br />`` ,"t� . E Ilia ,rl t��P <br />1 <br />ENS <br />ZS <br />F <br />:y <br />co <br />mod`; <br />y,'�u^ $�u91S�1Y� <br />To the best of the Engineers knowledge, information and belief, <br />the structural plans and specifications contained within these <br />drawings comply with the 2020 <br />Florida Building Code - <br />Residential 7th Edition. Engineer's signature and seal is only for <br />the structural engineering portions <br />of the drawing pages bearing <br />Engineer's signature and seal. <br />M <br />W <br />AgaF <br />a <br />o co <br />C)m 8o r u <br />N J <br />N O> W <br />V <br />I O <br />WN <br />O' � J <br />'5oW 00 N; LL W <br />a <br />rAtir ° - W a <br />�Mv � °' Y <br />Mu-u- a y <br />C)13 <br />Z <br />_ <br />v_ o <br />fY <br />r T O O F- W <br />5 'F1 N cO 2 O J <br />Z <br />ILa <br />Z <br />N M Z W Sg O <br />p V U a <br />W <br />❑ ❑ ❑ <br />M !�2 <br />IRRI <br />0 00 <br />Z N <br />z o � <br />� <br />rz in <br />V) <br />M <br />z a <br />w <br />U <br />O <br />Ln <br />�N <br />w o <br />Ly N <br />� w <br />U <br />I <br />U 11 <br />¢ m <br />o <br />�m <br />o <br />M <br />w <br />co <br />z <br />o <br />Z <br />a <br />U_ <br />Eo <br />� <br />zo <br />o0 <br />w- <br />rN <br />¢� <br />Z® <br />oa <br />U CIO <br />0.0 <br />i <br />o <br />x <br />a� <br />i <br />ao <br />0 O <br />2 <br />a <br />CN <br />n3 <br />CVJ C:°z <br />- <br />0 o <br />0 <br />(UNm <br />aw <br />z <br />z <br />oLL <br />a <br />U <br />a� <br />CD <br />3 <br />�Ir <br />Y <br />O <br />CIOa <br />V <br />w <br />z< <br />0 <br />N O <br />' ^ <br />Y 1 <br />I.NL <br />O <br />°' <br />rn <br />m <br />tV <br />0 <br />L <br />C <br />' <br />co <br />J <br />r <br />10� <br />O <br />Qom„ <br />IV m <br />UC\4 <br />1 <br />r <br />r- <br />= N <br />0') <br />•- <br />0 M <br />U—)<A <br />N <br />T <br />1= <br />w r <br />c <br />c-5 <br />C� <br />.. <br />o <br />z <br />Z <br />E <br />E <br />CU <br />c <br />d <br />E o <br />U <br />m <br />Q p <br />m <br />JOB <br />NO : <br />21-4273 <br />SCALE : <br />AS NOTED <br />SHEET NO. <br />3.2 <br />