|
,yyl►. ,: LU J...116_.•. Ill'i L_ 6 .1.1.. ._ _ .�_,y.J..�:,aJ1Y. .WLAINM��rr�wr.. ....L. :tiK-s'•�u-.r.wL.r.. - - - _ J, .1111=•1;.L r.1 i.. -ei ' ' - - - - --.L.:�-- - - ----- '-'�-. _ .L N
<br />THH
<br />0651 FL TAKE HIGH HIGHER - SCOPE OF WORK:
<br />STRUCTURAL
<br />BARRIER REMOVAL - SCOPE OF
<br />WORK:
<br />GENERAL
<br />INFORMATION:
<br />FRONT
<br />CHECKOUT:
<br />RETAIL-
<br />EXTERIOR:
<br />MEN'S RESTROOM:
<br />WOMEN'S
<br />RESTROOM:
<br />CONTRACTOR TO PROVIDE / COORDINATE THE FOLLOWING:
<br />1.
<br />REMOVE/RELOCATE MERCHANDISE FIXTURES AS SHOWN.
<br />1. REMOVE VINYL BASE ON ENTIRE RETAIL AREA, COORDINATE
<br />1.
<br />RESTRIPE ALL ACCESSIBLE PARKING FACES AND ACCESS
<br />1.
<br />REMOVE EXISTING HAND DRYER THAT IS A PROTRUDING
<br />1.
<br />REMOVE EXISTING HAND DRYER THAT IS A PROTRUDING
<br />1.
<br />CONSTRUCTION SUPERINTENDENT TO BE ON -SITE DURING ALL
<br />2•
<br />EXISTING 20'-4'CHECKOUT TO REMAIN. SEE STRUCTURAL
<br />WITH NAI VENDOR.
<br />AISLES IN CONTRASTING COLOR TO PROVIDE 144' MINIMUM
<br />OBJECT. HAND DRYER TO BE RELOCATED TO DIFFERENT WALL
<br />OBJECT. HAND DRYER TO BE RELOCATED TO DIFFERENT WALL
<br />BARRIER REMOVAL SCOPE OF WORK FOR ADA CHECKOUT.
<br />2• REMOVE LOWER TRIM BOARD AROUND RETAIL PATCH, REPAIR
<br />WIDTH PARKING SPACE & 60' MINIMUM WIDTH ACCESS AISLE.
<br />INSTALL NEW COMPLIANT MODEL HAND DRYER ADJACENT TO
<br />INSTALL NEW COMPLIANT MODEL HAND DRYER ADJACENT TO
<br />CONSTRUCTION ACTIVITIES.
<br />3.
<br />RELOCATE EXISTING HELIUM AND SECURE TO WALL
<br />AND PAINT.
<br />2.
<br />REPAINT PARKING SPACES ALONG THE ENTIRE FRONTAGE OF
<br />THE LAVATORY & MOUNT AT 40"AFF MAX TO HIGHEST
<br />THE LAVATORY OUTSIDE THE ACCESSIBLE STALL & MOUNT AT
<br />2.
<br />PAY PERMIT FEE AND PROVIDE BUILDING DEPARTMENT WITH
<br />4.
<br />PATCH, REPAIR, AND PAINT FRONT WALL (PT20).
<br />3. REMOVE WALL COVERING AND LAMINATE THROUGHOUT RETAIL
<br />STORE WHERE ACCESSIBLE PARKING IS LOCATED.
<br />OPERABLE PART. PATCH, REPAIR AND REFINISH WALL AS
<br />40"AFF MAX TO HIGHEST OPERABLE PART. PATCH, REPAIR AND
<br />ALL PERTINENT INFORMATION AS REQUIRED, COORDINATE WITH
<br />5.
<br />6.
<br />PATCH AND REPAIR CARPET AND BASE AS REWIRED.
<br />INSTALL NEW CARPET (FF18) BEHIND CHECKOUT.
<br />PATCH, REPAIR AND PAINT.
<br />4. REMOVE ALL EXISTING AISLE MARKERS. COORDINATE WITH
<br />3.
<br />ALTER SLOPE OF ACCESSIBLE PARKING SPACES AND ACCESS
<br />AISLES TO HAVE A MAXIMUM SLOPE &CROSS -SLOPE OF 1.59'r
<br />2.
<br />REQUIRED. EXTEND POWER TO NEW LOCATION.
<br />REMOVE PORTABLE WASTE RECEPTACLE AND INSTALL NEW
<br />REFINISH WALL AS REQUIRED. EXTEND POWER TO NEW
<br />LOCATION.
<br />AOR AS NECESSARY. OBTAIN SUB -PERMITS AS REQUIRED.
<br />7.
<br />INSTALL NEW VINYL BASE (fF16).
<br />STORE
<br />CONTRACTOR TO USE APPROPRIATE QC METHODS SO THAT
<br />SURFACE MOUNTED WASTE RECEPTACLE AT 2'-6' AFF TO
<br />2.
<br />RESTROOM DOOR DOES NOT HAVE REQUIRED MANEUVERING
<br />3.
<br />SECURE NECESSARY PERMITS, INCLUDING PERMIT(S) FOR
<br />8.
<br />INSTALL MG PRINTER AND CASH DRAWER AT CHECKOUT.
<br />5. REMOVE EXISTING HANGING GRAPHICS AND TRACKS
<br />SHALLOWER SLOPES DO NOT CREATE PONDING. PROVIDE A
<br />OPENING.
<br />CLEARANCES OF 18'WIDTH BY 60'DEEP MINIMUM. CURRENTLY
<br />THROUGHOUT
<br />FLUSH TRANSITION BETWEEN SURFACE MATERIALS.
<br />3.
<br />ADJUST CLOSER SO IT HAS A CLOSING SPEED FROM 90'OPEN
<br />HAS 15.5"CLEAR ON PULL SIDE OF DOOR. REMOVE EXISTING
<br />STORE SET-UP TRAILERS, PRIOR TO START CONSTRUCTION.
<br />6. REMOVE/RELOCATE AND INSTALL NEW POWER POLES AS
<br />4.
<br />REPAIR AND/OR FILL GAPS AT EXPANSION JOINTS ALONG
<br />TO 12'FROM THE LATCH IS 5 SECONDS MINIMUM. ADJUST
<br />DOOR, FRAME, HARDWARE & SHIFT DOORWAY 2 %"CLOSER TO
<br />4.
<br />PROVIDE SUB -CONTRACTOR TRADES AS REQUIRED.
<br />REQUIRED
<br />ACCESSIBLE ROUTE FROM ACCESS AISLE TO BUILDING
<br />DOOR CLOSER TO REQUIRE LESS THAN 5 LEIS OF FORCE TO
<br />HINGED SIDE. RELOCATE EXISTING DOOR, HARDWARE AND
<br />5.
<br />STORAGE TRAILER AND CONTAINERS ARE THE RESPONSIBILITY
<br />7. EXISTING ECC TO REMAIN IN RETAIL
<br />SIDEWALK. CONDITION OCCURS AT TWO LOCATIONS ALONG THE
<br />OPERATE.
<br />INSTALL NEW DOOR FRAME. PATCH, REPAIR AND REFINISH
<br />OF THE GC / STORE SET-UP MANAGER.
<br />PHQTOLAB I DIGITAL CAFE:
<br />1. EXISTING PLUMBING CHASE TO REMAIN. LIGHTLY SAND
<br />8. INSTALL NEW FLM AND PROVIDE POWER.
<br />9• REPLACE CEILING TILES WITH POWER POLE RELOCATION.
<br />ROUTE FROM THE ENTRY. EXPANSION JOINT OPENINGS IN
<br />GROUND SURFACES SHALL NOT BE GREATER THAN W WIDE OR
<br />4.
<br />REMOVE EXISTING RESTROOM SIGNAGE (MOUNTED ON DOOR) &
<br />INSTALL NEW ACCESSIBLE RLB RESTROOMwSIGN. SHIFT
<br />WALL AS REQUIRED (MATCH EXISTING RESTROOM & HALLWAY
<br />WALL FINISHES). EXTEND GYPSUM BOARD CEILING IN RESTROOM
<br />6.
<br />GC TO PROVIDE LIGHTING IN CONTAINERS FOR NIGHT TIME
<br />LAMINATE AND PAINT (PT20) MhiH EPDXY PANT.
<br />10. RELOCATE, LEVEL, AND STRAIGHTEN MERCHANDISING
<br />3i"DEEP IN DIRECTION OF TRAVEL
<br />LOCATION & MOUNT SIGN TO PROVIDE 18 X 18 CLEAR FLOOR
<br />TO MATCH EXISTING. PAINT P1 ATRIUM WHITE. INSTALL NEW
<br />VISIBILITY.
<br />2.
<br />TT
<br />REMOVE EXISTING PHO OLAB MILLWORK. SAVE U11U11ES AND
<br />GONDOLAS XTURES PER LATEST MERCHANDISE PLAN.
<br />11. REPLACE DAMAGED AND STAINED CEILING TILES WITH NEW
<br />5.
<br />INSTALL NEW ACCESSIBLE ROUTE FROM PUBLIC SIDEWALK TO
<br />SPACE CENTERED ON THE TACTILE CHARACTERS AND BEYOND
<br />11LE & BASE IN RESTROOM TO MATCH EXISTING.
<br />7.
<br />COORDINATE LOCATION OF STORAGE CONTAINER AND
<br />3.
<br />EQUIPMENT FOR RELOCATION.
<br />RELOCATE EXISTING PASSPORT SCREEN AS DIRECTED BY
<br />TILES; 4 BOXES MAXIMUM.
<br />STORE ENTRY. REMOVE EXISTING CURBS (AS REQUIRED).
<br />INSTALL NEW CONCRETE SIDEWALK WITH SLOPE NOT 0
<br />T
<br />THE ARC OF THE DOOR SWING. MOUNT ON LATCH SIDE OF
<br />DOOR AT 60' AFF MAXIMUM TO THE TOP OF RESTROOM SIGN
<br />3.
<br />REMOVE PORTABLE WASTE RECEPTACLES AND INSTALL NEW
<br />SURFACE MOUNTED WASTE RECEPTACLES AT 2'-6' AFF TO
<br />DUMPSTER WITH STORE MANAGER. (NO ITEMS ARE TO BE
<br />STORE MANAGER AND COORDINATED WITH CPM.
<br />12. PATCH, REPAIR, AND PAINT WALLS AS REQUIRED (PT20).
<br />EXCEED 4.5% AND CROSS -SLOPE NOT TO EXCEED 1.5X VERIFY
<br />& 48' MINIMUM TO THE TOP OF RESTROOM SIGN. PATCH,
<br />OPENING INSIDE AND OUTSIDE OF THE ACCESSIBLE STALL
<br />LEFT IN THE BACKROOM).
<br />4.
<br />REMOVE EXISTING SINK AND CAP PLUMBING.
<br />13. PATCH AND REPAIR CARPET (FF1) WITH GONDOLA MOVES AND
<br />SLOPES OF ACCESSIBLE ROUTE TO STORE ENTRY (MAXIMUM
<br />REPAIR AND REFINISH WALL AS REQUIRED.
<br />4.
<br />ADJUST CLOSER SO IT HAS A CLOSING SPEED FROM 90' OPEN
<br />5.
<br />REMOVE EXISTING SOAP AND PAPER TOWEL DISPENSERS.
<br />VINYL BASE (FF16) INSTALLATION ON ENTIRE RETAIL AREA.
<br />SLOPE 4.57% MAXIMUM CROSS -SLOPE 1.5%).
<br />5.
<br />CURRENTLY THERE IS 48.25°FROM SIDE WALL TO EDGE OF
<br />TO 12'FROM THE LATCH IS 5 SECONDS MINIMUM. ADJUST DOOR
<br />8.
<br />OFFLOAD & PROPERLY STORE ALL CONSTRUCTION MATERIAL
<br />6.
<br />RELOCATE EXISTING FIRE EXTINGUISHER.
<br />14. NEW CARPET (FF10) AND VINYL BASE (FF16) INSTALLATION ON
<br />6
<br />REPAIR AND/OR ALL SIDEWALK ,101NT ALONG ACCESSIBLE
<br />LAVATORY AND 15'FROM CENTERLINE OF LAVATORY TO TOILET
<br />CLOSER TO REQUIRE LESS THAN 5 LEIS OF FORCE TO
<br />9.
<br />DEVELOP CONSTRUCTION TIMELINE AND PHASING PLAN WITH
<br />7.
<br />REMOVE AND REPLACE DRYWALL AT SINK LOCATION AS
<br />REQUIRED.
<br />ENTIRE RETAIL AREA BY VENDOR TH CARPET REPLACEMENT
<br />PROGRAM.
<br />.
<br />ROUTE. JOINT IS CURRENTLY 1-WIDE AND %'DEEP.
<br />PARTITION. RESTROOM WILL BE CONVERTED TO A SINGLE
<br />USER TOILET ROOM. INSTALL NEW PRIVACY HARDWARE.
<br />5.
<br />OPERATE.
<br />REMOVE EXISTING RESTROOM SIGNAGE (MOUNTED TO DOOR) &
<br />CVS CPM AND STORE OPERATIONS. STORE IS OPEN 8AM TO
<br />10PM. GC TO PROPOSE SCHEDULE FOR
<br />8.
<br />RELOCATE EXISTING POS TO CHECKOUT.
<br />15. INSTALL NEW DRIVE AISLE CARPET (FF11). EXTEND DRIVE
<br />7.
<br />CROSS SLOPE OF ACCESSIBLE EXTERIOR ROUTE AT ENTRY
<br />PERPENDICULAR TO THE DIRECTION OF TRAVEL) EXCEEDS 1:48
<br />REMOVE TOILET PARTITION AND STALL DOOR. REMOVE EXISTING
<br />INSTALL NEW ACCESSIBLE RLB RESTROOM SIGN. SHIFT
<br />IS HOURLY
<br />9.
<br />REMOVE EXISTING DIGITAL PHOTO EQUIPMENT AND SAVE FOR
<br />AISLE.
<br />LAVATORY, MIRROR, HAND DRYER AND SOAP DISPENSER INSIDE
<br />LOCATION &MOUNT SIGN TO PROVIDE 18w X 180CLEAR FLOOR
<br />CONSTRUCTION OVERNIGHT AND COORDINATE WITH CPM.
<br />RELOCATION.
<br />16. RECONNECT NEW OR RELOCATED WALL FIXTURES INTO
<br />2.08% CROSS SLOPE IS 4.4% AND 4.OX
<br />ACCESSIBLE STALL CAP PLUMBING LINES. PATCH, REPAIR AND
<br />SPACE CENTERED ON THE TACTILE CHARACTERS AND BEYOND
<br />10.
<br />PROPOSED WORK WILL BE COMPLETED OVERNIGHT ASS
<br />10.
<br />REMOVE EXISTING CARPET, PREPARE SURFACE FOR NEW
<br />LIGHTED
<br />EXISTING POWER SOURCE FOORR LIGHTED HEADERS.
<br />8.
<br />[TER EXISTING EXTERIOR ROUTE TO REDUCE CROSS SLOPE TO
<br />REFINISH WALL AS REQUIRED TO MATCH EXISTING.REMOVE
<br />THE ARC OF THE DOOR SWING. MOUNT ON LATCH SIDE OF
<br />FLOORING.
<br />17. INSTALL NEW CORNER BOXES AND END PANELS AS SHOWN.
<br />1.5% OR LESS
<br />EXISTING URINAL AND SCREEN. CAP PLUMBING. PATCH REPAIR
<br />DOOR AT 60' AFF MAXIMUM TO THE TOP OF RESTROOM SIGN
<br />DISCUSSED IN PRE -BID. FOLLOW SCHEDULING NIGHT WORK
<br />11.
<br />REMOVE EXISTING PHOTO LAB WALL GRAPHICS.
<br />1& INSTALL NEW PIN LETTERS ORDERED BY STORE SET-UP,
<br />(
<br />AND REFINISH WALL AS REQUIRED TO MATCH EXISTING.
<br />& 48' MINIMUM TO THE TOP OF RESTROOM SIGN. PATCH,
<br />CRITERIA 2011 DOCUMENT.
<br />12.
<br />REMOVE GATE.
<br />INSTALLED BY G.G.).
<br />INTERIOR:
<br />6.
<br />REMOVE EXISTING URINAL AND SCREEN. CAP PLUMBING.
<br />REPAIR AND REFINISH WALL AS REQUIRED.
<br />11.
<br />PROVIDE DUMPSIER FOR ALL CONSTRUCTION DEBRIS, SECURE
<br />13.
<br />14.
<br />REMOVE VINYL BASE.
<br />REMOVE CARPET, PREPARE SURFACE FOR NEW.
<br />19. INSTALL NEW AISLE MARKERS (ORDERED BY STORE SET-UP
<br />7.
<br />ALTER EXISTING FLOOR SURFACE WITHIN REQUIRED FLOOR
<br />SPACE INSIDE ACCESSIBLE STALL SO AS THE SLOPE DOES NOT
<br />6.
<br />PROVIDE DOOR SELF CLOSER ON ACCESSIBLE TOILET STALL
<br />PERMIT IF REQUIRED.
<br />15.
<br />INSTALL NEW OPTION 'C'PHOTO LAB INCLUDING NEW
<br />INSTALLED BY G.G.). AISLE MARKERS TO BE INSTALLED AT
<br />9'-0°TO BOTTOM FROM FINISHED FLOOR. VERIFY THAT AISLE
<br />RETAIL
<br />EXCEED 1.5% IN ALL DIRECTIONS. RAISE FLOOR DRAIN AND
<br />7,
<br />DOOR
<br />PROVIDE DOOR PULL ON PUSH SIDE OF ACCESSIBLE TOILET
<br />12.
<br />COORDINATE ALL INSPECTIONS WITH THE COUNTY AS
<br />REQUIRED.
<br />16.
<br />MILLWORK, COUNTERS, CABINETS, AND UTILITIES.
<br />REINSTALL EXISTING DIGITAL PHOTO EQUIPMENT AND PROVIDE
<br />MARKERS DON'T BLOCK PIN LETTERS.
<br />1.
<br />REMOVE EXISTING STAND ALONE PRICE CHECKER IN RETAIL
<br />REPLACE PRICE CHECKER WITH A NEW COMPLIANT MODEL SO
<br />8.
<br />MODIFY FLOOR TO PROVIDE 1.5% MAX SLOPE.
<br />REMOVE EXISTING TILE FLOORING AND BASE AND INSTALL NEW
<br />STALL DOOR CENTERED AT 34" MINIMUM TO 48' MAXIMUM AFF,
<br />INSTALLED NEAR THE LATCH SIDE OF THE DOOR. THERE
<br />13.
<br />STORE PERSONNEL AND/OR STORE SETUP ARE RESPONSIBLE
<br />17.
<br />ELECTRICAL CONNECTION AND DATA.
<br />REINSTALL (2) EXISTING DIGITAL ORDER STATIONS ON NEW
<br />20. REPAINT ALL METAL DOORS AND FRAMES INCLUDING
<br />EMERGENCY EXIT DOOR) IN RETAIL (PT-20).
<br />THE DISPLAY SCREEN IS VISIBLE FROM A POINT LOCATED 40'
<br />ABOVE THE CENTER OF THE CLEAR FLOOR SPACE. PROVIDE A
<br />CERAMIC TILE T1 BY DALTILE, SALERNO, GRIGO PERLA SL84.
<br />FLOOR TILE TO BE 12X12 / COVE BASE 6X12, LATICRETE
<br />CURRENTLY IS A DOOR PULL PROVIDED ONLY ON THE PULL
<br />SIDE
<br />FOR ALL MERCHANDISE MOVES INCLUDING PHARMACY.
<br />COUNTER.
<br />21. CLEAN STOREFRONT GLASS.
<br />30X48'CL.EAR FLOOR SPACE. MOUNT UNIT SO HIGHEST
<br />GROUT 160 DUSTY GREY. ADJUST FLOOR DRAIN FLUSH WITH
<br />8,
<br />PROVIDE NEW LOCKING HARDWARE ON ACCESSIBLE STALL
<br />14.
<br />RELOCATE, LEVEL, AND STRAIGHTEN MERCHANDISING
<br />18•
<br />19.
<br />INSTALL NEW GATE.
<br />REINSTALL MONEYGRAM.
<br />22. CLEAN CEILING DIFFUSERS AND RETURN AIR GRILLES.
<br />2.
<br />OPERABLE PART IS AT 48°MAX.
<br />RELOCATE EXISTING CUSTOMER SERVICE BUTTON IN AISLE 8 TO
<br />9•
<br />NEW FINISH.
<br />RELOCATE EXISTING COMPLIANT 36°LONG REAR GRAB BAR.
<br />9.
<br />Dom'
<br />RELOCATE LAVATORY AND MIRROR INSIDE THE ACCESSIBLE
<br />GONDOLAS/FIXTURES (ONLY IF GC HAS GONDOLA TRAIN).
<br />20.
<br />PATCH, REPAIR, AND PAINT WALLS (PT20).
<br />BE WITHIN REACH RANGES AT 48'AFF FOR FORWARD AND
<br />PROVIDE 1 %'MIN CLEARANCE BELOW GRAB BAR TO TOP OF
<br />STALL (CURRENTLY FROM SIDE WALL) AND PROVIDE 60"
<br />COORDINATE WITH STORE SETUP CREW LEAD.
<br />21.
<br />INSTALL NEW CARPET (FF18) BEHIND CHECKOUT.
<br />PARALLEL
<br />L APPROACH.
<br />WATER CLOSET TANK. MOUNT REAR GRAB BAR TO EXTEND
<br />SIDE WALL. MOUNT AT MAXIMUM 4'AFF NTH A MINIMUM
<br />15.
<br />PATCH AND REPAIR CARPET WITH THE RELOCATION OF ALL
<br />22.
<br />23.
<br />INSTALL NEW VINYL BASE (FF16).
<br />INSTALL NEW PHOTO LAB WALL GRAPHICS. COORDINATE WITH
<br />3.
<br />INSTALL NEW TACTILE 6X9•" EMERGENCY EXIT ONLY" SIGNAGE
<br />AT RETAIL & STOCKROOM EMERGENCY EXIT. SIGN TO BE
<br />FROM CENTERLINE OF WATER CLOSET 12 INCHES MINIMUM ON
<br />ONE SIDE AND 24 INCHES MINIMUM ON THE OTHER SIDE. BAR
<br />CLEARANCE OF 29 FROM FINISHED FLOOR TO BOTTOM OF
<br />APRON. MAINTAIN 60' MIN. CLEAR FROM THE EDGE OF
<br />MERCHANDISING GONDOLAS. PATCH CARPET UNDER
<br />LSI.
<br />MOUNTED ON FACE OF OUT -SWINGING DOOR. ALSO PROVIDE
<br />TO BE INSTALLED BETWEEN 33°MIN. AND 36°MAX. AFF TO TOP
<br />LAVATORY TO TOILET SIDE WALL AND 15'MIN. FROM
<br />GONDOLAS AS NECESSARY TO AVOID TRIP HAZARDS.
<br />24.
<br />INSTALL NEW FIXTURES AS SHOWN.
<br />VERTICAL 9'X2' EXIT'SIGNAGE AT THE FRONT ENTRANCE
<br />OF GRIPPING SURFACE PATCH, REPAIR AND REFINISH WALL AS
<br />CENTERLINE OF LAVATORY TO SIDE PARTITION. REFER TO
<br />16.
<br />FULL CARPET REPLACEMENT TO BE ORDERED AS DIRECTED BY
<br />LOCATED ON RIGHT DOOR FRAME EDGE, TOWARDS CENTER OF
<br />DOORS. PROVIDE NEW SIGN NTH WHITE RAISED TEXT AND
<br />10.
<br />REQUIRED.
<br />REMOVE 2 EXISTING PAPER TOWEL DISPENSER. PATCH &
<br />ACCESSORY MOUNTING HEIGHTS DETAIL FOR MOUNTING HEIGHTS
<br />AND KNEE AND TOE CLEARANCES. PATCH, REPAIR AND
<br />CPM IN RETAIL ONLY.
<br />COOLER AREA
<br />RAISED BRAILLE TEXT. PROVIDE 180X18' CLEAR FLOOR SPACE
<br />REPAIR A AS REQUIRED.
<br />REFINISH WALL AS REQUIRED.
<br />17.
<br />NEW CARPET SCOPE OF WORK INCLUDES RETAIL, HALLWAY,
<br />CENTERED ON THE TACTILE CHARACTERS AND BEYOND THE
<br />11.
<br />INSTALL NEW 18"MIN. VERTICAL GRAB BAR WITH BOTTOM OF
<br />10.
<br />RELOCATE TOILET PARTITION TO EXPAND ACCESSIBLE AND
<br />PHOTO, CHECKOUT, DRIVE AISLE PHARMACY.
<br />1.
<br />REMOVE EXISTING VCT, PREPARE SURFACES FOR NEW
<br />ARC OF THE DOOR SWING. SIGNAGE TO BE MOUNTED AT 60'
<br />BAR 40'AFF WITH THE CENTERLINE OF THE BAR LOCATED 40"
<br />STANDARD STALL REINSTALL TOILET PARTITION TO PROVIDE
<br />18.
<br />GC RESPONSIBLE FOR CARPET INSTALLATION IN THE
<br />2.
<br />FLOORING.
<br />REMOVE CARPET, PREPARE SURFACES FOR NEW FLOORING.
<br />AFF MAX. TO TOP OF SIGN AND & 48' AFF MIN. TO BOTTOM
<br />OF SIGN
<br />FROM REAR WALL PER CVS REQUEST. INSTALL BLOCKING IN
<br />WALL TO REINFORCE THE NEW VERTICAL GRAB BAR. PATCH,
<br />15'MINIMUM FROM CENTERLINE OF LAVATORY INSIDE
<br />ACCESSIBLE STALL TO THE PARTITION. INSTALL NEW SECTION
<br />PHARMACY, AND BEHIND CHECKOUT. GC IS ALSO RESPONSIBLE
<br />3.
<br />INSTALL NEW VCT (FF22) IN FRONT AND UNDER EXISTING
<br />REPAIR AND REFINISH WALL AS REQUIRED.
<br />OF TOILET PARTITION TO MATCH EXISTING GRAY LAMINATE AS
<br />FOR REMOVAL AND INSTALLATION OF NEW VCT AT COOLER
<br />COOLERS/FREEZER LOCATION AS SHOWN. LEVEL TRANSITION
<br />12.
<br />INSTALL INSULATION AT HOT WATER AND DRAIN PIPES AS
<br />O T WELL AS PROTECTION AT THE HOT & COLD WATER SUPPLY
<br />REQUIRED. PATCH, REPAIR AND REFINISH WALL &FLOOR TO
<br />MATCH EXISTINGFINISHES.
<br />LOCATION.
<br />4.
<br />BETWEEN VCT AND CARPET.
<br />PATCH, REPAIR, AND PAINT WALL (PT20) BENJAMIN MOORE
<br />HALLWAY:
<br />VALVES UNDER LAVATORY.
<br />11.
<br />RELOCATE EXISTING FRAMED MIRROR INSIDE THE ACCESSIBLE
<br />19.
<br />INSTALL FURRING STRIPS FOR WALL FIXTURES AS NEEDED.
<br />WINDS BREATH.
<br />1.
<br />EXISTING tOW'DRINKING FOUNTAIN APRON IS AT 26'AFF.
<br />13.
<br />LOWER EXISTING BABY CHANGING STATION SO THAT THE WORK
<br />STALL TO 40'MAXIMUM HEIGHT TO THE REFLECTIVE SURFACE
<br />20.
<br />COORDINATE AND INSTALL ALL COMMUNICATION WIRING (EAS,
<br />5.
<br />INSTALL NEW PIN LETTERS (ORDERED BY STORE SET-UP,
<br />RAISE EXISTING tOW'DRINKING FOUNTAIN. PATCH & REPAIR
<br />WALL TO MATCH EXISTING. MOUNT EXISTING LOW DRINKING
<br />SURFACE IS AT 28"AFF MIN TO 34'AFF MAX, PROVIDE 27"MIN
<br />KNEE CLEARANCE, AND HANDLE AT 48'AFF MAX. PATCH,
<br />OF THE MIRROR OUTSIDE OF THE ACCESSIBLE STALL CENTER
<br />MIRROR ON LAVATORY. PATCH, REPAIR AND REFINISH WALL AS
<br />21.
<br />PHONES, POS).
<br />COORDINATE BURGLAR AND FIRE ALARM RELOCATION /
<br />6.
<br />7.
<br />INSTALLED BY G.G.).
<br />CLEAN COOLER EEZER EXTERIOR, AND TOPS
<br />INSTALL NEW COOLER END PANELS AS REQUIRED.
<br />FOUNTAIN TO ALLOW 27'MINIMUM KNEE CLEARANCE 30"
<br />MINIMUM WIDTH, WMINIMUM DEPTH AT 27'AFF AND '11°MINIMUM
<br />14.
<br />REPAIR AND REFINISH WALL AS REQUIRED.
<br />REMOVE EXISTING FAUCET CONTROL AND INSTALL NEW
<br />12.
<br />REQUIRED.
<br />REMOVE 2 EXISTING PAPER TOWEL DISPENSER. PATCH &
<br />DEPTH AT 9' AFT-, TOE CLEARANCE TO BE 9" AFF MINIMUM, 30'
<br />LEVER -TYPE FAUCET HANDLE AT LAVATORY. HARDWARE SHALL
<br />REPAIR WALL AS REQUIRED.
<br />INSTALLATION WITH CVS ASSOCIATED PROTECTION SERVICES
<br />MINIMUM WIDTH, 17-MINIMUM DEPTH, SPOUT AT 36-MAX AFF.
<br />NOT REQUIRE MORE THAN 5 LEIS OF FORCE TO OPERATE &
<br />13.
<br />INSTALL NEW 18'MIN. VERTICAL GRAB BAR WITH BOTTOM OF
<br />(APS) DEPARTMENT.
<br />(PLEASE NOTE: IF THE DRINKING FOUNTAIN IS MOUNTED SO
<br />SHALL NOT REQUIRE TIGHT GRASPING PINCHING OR TWISTING
<br />OF THE WRIST.
<br />BAR 40°AFF WITH THE CENTERLINE OF THE BAR LOCATED 40'
<br />22.
<br />COORDINATE AND PAY FOR CCTV CAMERA RELOCATION.
<br />MANAGERS
<br />1.
<br />OFFICE:
<br />CLEAN RETAIL SIDE OF MANAGER'S OFFICE AND DOOR.
<br />THAT THE UNDERSIDE IS LESS THAN 27' AFF, THEN THE KNEE
<br />SPACE WILL NOT BE COMPLIANT, AND IF THE DRINKING
<br />15.
<br />REMOVE EXISTING FRP. PATCH, REPAIR (SKIM WALLS), AND
<br />FROM REAR WALL PER CVS REQUEST. INSTALL BLOCKING IN
<br />WALL TO REINFORCE THE NEW VERTICAL GRAB BAR. PATCH,
<br />23.
<br />CLEAN ALL AIR SUPPLY AND RETURN GRILLES AND CEILING
<br />FOUNTAIN IS MOUNTED SO THAT THE BOTTOM IS GREATER
<br />PAINT WALLS. WALLS TO BE PAINTED PT28 BENJAMIN MOORE
<br />REPAIR AND REFINISH WALL AS REQUIRED.
<br />PANELS IN PHARMACY, RX WAITING, RETAIL, RESTROOMS &
<br />PHARMACY:
<br />THAN 27' AFF, AND IT IS NOT IN AN ALCOVE, THEN IT WILL
<br />V342 ATRIUM WHITE COROTECH HIGH PERFORMANCE
<br />PRE -CATALYZED WATERBORNE EPDXY, EGGSHELL FINISH.
<br />14.
<br />RAISE LAVATORY OUTSIDE THE ACCESSIBLE STALL & MOUNT
<br />AT MAXIMUM 34'AFF WITH A MINIMUM CLEARANCE OF 29'FROM
<br />HALLWAY.
<br />BE A PROTRUDING OBJECT BECAUSE IT EXTENDS MORE THAN
<br />4' FROM THE WALL AT A HEIGHT BETWEEN 27' AND 80' AFF.
<br />16.
<br />CLEAN AND PAINT EXISTING CEILING P1, ATRIUM WHITE.
<br />FINISHED FLOOR TO BOTTOM OF APRON. MAINTAIN 60'MIN.
<br />24.
<br />ALLOW FOR 6 BOXES OF CEILING TILES FOR REPLACEMENT OF
<br />1.
<br />2
<br />REMOVE RX ANCILLARY SIGNS.
<br />REMOVE VINYL BASE.
<br />2010 ADA 306.3. IF THE MAXIMUM SPOUT HEIGHT CAN BE
<br />17.
<br />18.
<br />RESTROOMS TO BE INDUSTRIALLY CLEANED.
<br />CLEAN EXISTING SUPPLY & RETURN GRILLS.
<br />CLEAR FROM THE EDGE OF LAVATORY TO TOILET SIDE WALL
<br />DAMAGED.
<br />3.
<br />REMOVE CARPET, PREPARE SURFACE FOR NEW.
<br />MAINTAINED, CONSIDER MOUNTING THE WATER COOLER SO
<br />FROM CENTERLINE OF LAVATORY TO SIDE
<br />AND PARTITION. REFER
<br />TITION. PAR REFER TO ACCESSORY MOUNTING HEIGHTS DETAIL
<br />25.
<br />REPLACE UP TO 6 LIGHT BULBS.
<br />4.
<br />PATCH, REPAIR, AND PAINT ALL INTERIOR RX WALLS AS
<br />THAT THE UNDERSIDE IS SLIGHTLY HIGHER THAN 27' AFF TO
<br />FOR MOUNTING HEIGHTS AND KNEE AND TOE CLEARANCES.
<br />26.
<br />RELOCATE EXISTING FIRE EXTINGUISHERS AS REQUIRED.
<br />REQUIRED (PT23) BENJAMIN MOORE FAIRVIEW BLUE.
<br />ENSURE COMPLIANT KNEE SPACE.)
<br />PATCH, REPAIR AND REFINISH WALL AS REQUIRED.
<br />27.
<br />RELOCATE AND ADD CASH BOXES PER PLAN.
<br />5.
<br />INSTALL NEW CARPET (FF18).
<br />2.
<br />INSTALL A CANE TOUCH APRON WITH LOWEST EDGE AT 27'
<br />15.
<br />INSTALL INSULATION AT HOT WATER AND DRAIN PIPES AS
<br />6.
<br />INSTALL NEW VINYL BASE (FF16).
<br />AFF UNDER `H1GH'DRINKING FOUNTAIN TO DIRECT BLIND OR
<br />WELL AS PROTECTION AT THE HOT & COL) WATER SUPPLY
<br />28.
<br />REMOVE ALL WALL COVERING AND LAMINATE FROM RETAIL
<br />7.
<br />PAINT VALANCE (RETAIL SIDE) AND UNDERSIDE OF VALANCE
<br />VISION -IMPAIRED INDIVIDUALS AROUND UNIT.
<br />VALVES UNDER LAVATORY INSIDE AND OUTSIDE OF THE
<br />WALLS. PATCH, REPAIR AND PAINT.
<br />(PT24) BENJAMIN MOORE RUBY RED.
<br />ACCESSIBLE STALL
<br />29.
<br />VERIFY EACH FIRE EXTINGUISHER HAS SIGNAGE IDENTIFYING
<br />8.
<br />INSTALL NEW RX ANCILLARY SIGNS TO MATCH THE GRAPHIC
<br />CHECKOUT,•
<br />16.
<br />REMOVE (3) EXISTING FAUCET CONTROLS AT LAVATORIES
<br />LOCATION PER NFPA 1- SECTION 6.1.3. INSTALL NEW SIGN
<br />9.
<br />PACKAGE.
<br />INSTALL NEW PIN LETTERS (ORDERED BY STORE SET-UP,
<br />1.
<br />REMOVE 4-Or'SECTION OF COUNTERTOP AT THE FRONT
<br />INSIDE & OUTSIDE OF THE ACCESSIBLE STALL AND INSTALL (3)
<br />NEW LEVER -TYPE FAUCET HANDLES AT LAVATORIES OUTSIDE
<br />TO MATCH EXISTING IF SIGN IS MISSING.
<br />INSTALLED G.G.
<br />CHECKOUT, CLOSEST TO THE ENTRANCE. INSTALL A NEW ADA
<br />SPEC 4'-0' SECTION WITH A HEIGHT OF 34' AFFMATCH
<br />THE ACCESSIBLE STALL HARDWARE SHALL NOT REQUIRE
<br />30.
<br />GC IS RESPONSIBLE FOR CONTACTING JURISDICTION AND
<br />10.
<br />INSTALL NEWW PH MACIST LEDGE AND PHOTO FRAMES.
<br />.
<br />EXISTING BEIGE MILLWORK.
<br />MORE THAN 5 LEIS OF FORCE TO OPERATE & SHALL NOT
<br />PROVIDE THE ACTUAL PERMITTING FEES INCLUSIVE IN BID.
<br />2.
<br />RELOCATE REGISTER AND CREDIT CARD READER TO NEW ADA
<br />REQUIRE TIGHT GRASPING, PINCHING, OR TVMS11NG OF THE
<br />WRIST.
<br />31.
<br />GC'S TO INCLUDE IN THEIR BID QUALIFICATIONS ANY
<br />PHARMACY WAITING:
<br />COUNTER.
<br />17.
<br />RELOCATE SOAP DISPENSER INSIDE THE ACCESSIBLE STALL TO
<br />ADDENDUMS AND PRE -BID NOTES.
<br />1.
<br />REMOVE VINYL BASE.
<br />3.
<br />4.
<br />RELOCATE EXISTING UNDERMOUNT EAS SCANNER.
<br />END PANEL TO BE RELOCATED AND RE -SECURED AFTER
<br />18.
<br />BE MOUNTED AT 40"AFF MAX TO HIGHEST OPERABLE PART.
<br />LOWER EXISTING BABY CHANGING STATION SO THAT THE WORK
<br />32.
<br />REPLACE ALL END PANELS AND CORNER BOXES. GC TO
<br />2.
<br />REMOVE CARPET; PREPARE SURFACE FOR NEW.
<br />REMOVING SECTION OF COUNTERTOP. RELAMINATE CUT EDGE
<br />SURFACE IS AT 28'AFF MIN TO 34°AFF MAX, PROVIDE 27-MIN
<br />VERIFY QUANTITY WITH MERCHANDISE PLAN (AND FINAL
<br />3.
<br />REMOVE (4) EXISTING WAITING CHAIRS.
<br />OF COUNTERTOP TO MATCH EXISTING.
<br />KNEE CLEARANCE, AND HANDLE AT 48°AFF MAX. PATCH,
<br />MERCHANDISE PLAN PRIOR TO ORDER).
<br />4.
<br />REMOVE EEXXISTING PRICE CHECKER MOUNTED TO WALL PATCH
<br />AND REPAIR.
<br />5.
<br />INSTALL CVS APPROVED ISA SIGNAGE AT ALL DESIGNATED
<br />ACCESSIBLE COUNTERS.
<br />REPAIR AND REFINISH WALL AS REQUIRED. REMOVE EXISTING
<br />5.
<br />REMOVE EXISTING HANGING GRAPHICS.
<br />FRP. PATCH, REPAIR (SKIM WALLS), AND PAINT WALLS. WALLS
<br />6.
<br />INSTALL NEW CHAIRRAIL (W18) AND PAINT BELOW (PT20).
<br />PHARMACY
<br />WAITING:
<br />TO BE PAINTED PT28 BENJAMIN MORE V342 ATRIUM WHITE
<br />COROTECH HIGH PERFORMANCE PRE -CATALYZED WATERBORNE
<br />GRAPHICS
<br />1.
<br />/ SIGNAGE:
<br />REMOVE EXISTING HANGING GRAPHICS AND TRACKS
<br />7.
<br />8.
<br />INSTALL NEW WALL COVERING (W12) ABOVE C HAIRRAIL
<br />INSTALL 3 NEW CHAIRS WITH NEW BRAND DESIGN (RED).
<br />1.
<br />REMOVE FIXED/MOVABLE SEATING, FURNISHINGS, AND/OR
<br />19.
<br />EPDXY, EGGSHELL FINISH.
<br />REMOVE EXISTING TILE FLOORING AND BASE AND INSTALL NEW
<br />THROUGHOUT.
<br />9.
<br />INSTALL PHARMACY SERVICE HOURS SIGNAGE
<br />ACCESSORIES AS REQUIRED TO PROVIDE 5% MINIMUM
<br />CERAMIC TILE T1 BY DALIILE, SAI.ERNO, GRIGIO PERLA SL84.
<br />2.
<br />REPLACE RX ANCILLARY SIGNS (DROP OFF, PICK UP &
<br />10.
<br />INSTALL NEW DRIVE AISLE CARPET (FETID.
<br />WHEELCHAIR SPACES IN WAITING AREA AND ON AN ACCESSIBLE
<br />ROUTE. PROVIDE 1 ACCESSIBLE SEAl1NG SPACE INSTALL NEW
<br />FLOOR TILE TO BE 12X12 /COVE BASE 6X12, LAl1CRElE
<br />CONSULTATION).
<br />11.
<br />INSTALL NEW VINYL BASE (FF16).
<br />'ACCESSIBLE WAITING" SIGN AT WALL IN WAITING AREA
<br />GROUT #60 DUSTY GREY. ADJUST FLOOR DRAIN FLUSH NTH
<br />3.
<br />REMOVE ALL RX WAITING AREA GRAPHICS.
<br />.
<br />NEW FINISH.
<br />4.
<br />REMOVE GREETING CARD CEILING SIGN (IF APPLICABLE).
<br />20.
<br />REPLACE EXISTING TOILET PARTITIONS. TOILET PAR11TON BY
<br />5.
<br />INSTALL NEW PIN LETTERS (ORDERED BY STORE SET-UP,
<br />HALLWAY:
<br />PHARMACY:
<br />GLOBAL PARTITIONS. STEEL SHEETS WITH POWDER -COATED
<br />INSTALLED BY
<br />1.
<br />PAINT HALLWAY DOORS AND FRAMES (20).
<br />1.
<br />RELOCATE CREDIT CARD READER TO PROVIDE 36' WIDE CLEAR
<br />FINISH: MILL-PHOSPHATIZED, CORROSION -RESISTANT STEEL
<br />SHEET, STRETCHER -LEVELED FLATNESS ASTM A 591/A 591M
<br />6.
<br />ISLE
<br />INSTALL NEW AISLE MARKERS (ORDERED BY STORE SET-UP,
<br />INSTALLED BY G.G.). AISLE MARKERS TO BE INSTALLED AT
<br />2.
<br />3.
<br />PATCH, REPAIR, AND PAINT WALLS (PT20).
<br />REMOVE CARPET, PREPARE SURFACE FOR NEW FLOORING.
<br />COUNTER SPACE AT REGISTER (CLOSEST TO THE GATE).
<br />REPAIR MILLWORK SURFACE.
<br />CLASS C, OR AS1M A 653/A 653M; WITH MANUFACTURER'S
<br />BOTTOM FROM FINISHED BOOR. VERIFY THAT AISLE
<br />4.
<br />INSTALL NEW CARPET FF11) AND VINYL BASE(FF16).GRILLES.
<br />2.
<br />CONSULTATION COUNTER KNEE CLEARANCE 34' AFF, 360 WIDE,
<br />21.
<br />STANDARD POWDER -COATED FINISH. COLOR: GRAY 2125.
<br />REPLACE EXISTING TOILET SEATS. MATCH COLOR AND SHAPE.
<br />MARKERS
<br />MARKERS DON'T BLOCK PIN LETTERS.
<br />5.
<br />CLEAN EXISTING AIR DUCT SUPPLY AND RETURN GRILLES.
<br />4.75' DEEP, ALCOVE DEPTH 20'. REMOVE THE LEDGE AND
<br />22.
<br />CLEAN AND PAINT EXISTING CEILING P1, ATRIUM WHITE.
<br />7.
<br />INSTALL NEW PLUMOLI) FOR EXISTING LIGHTED WINDOW SIGNS.
<br />REPLACE WITH NEW U-CHANNEL BY IMPRESSIONS.
<br />23.
<br />RESTROOMS TO BE INDUSTRIALLY CLEANED.
<br />8.
<br />REMOVE EXISTING WELCOME/OPEN 24 HOURS ENTRANCE SIGN.
<br />24.
<br />CLEAN EXISTING SUPPLY & RETURN GRILLS.
<br />PHOTO:
<br />ENTRY:
<br />1.
<br />ALL ITEMS TO BE ADDRESSED WITH THH SCOPE OF WORK.
<br />1.
<br />REMOVE PORTION OF CARPET AND RUBBER FLOORING AT
<br />2.
<br />REMOVE EXISTING 34' DOUBLE DROP-OFFS. INSTALL NEW 36'
<br />ENTRY; PREPARE SURFACE FOR NEW SOFT GRID MAT.
<br />ADA DROP-OFF WITH 17°MIN. DEPTH & 32' DROP-OFF,
<br />2.
<br />EXISTING FILM TO REMAIN.
<br />COLORS TO MATCH EXISTING. PROVIDE ISA SIGNAGE AT
<br />3.
<br />EXISTING ATM TO REMAIN.
<br />ACCESSIBLE DROP-OFF COUNTER. MATCH EXISTING MILLWORK.
<br />4.
<br />REMOVE MERCHANDISE FIXTURES AS SHOO.
<br />5.
<br />INSTALL NEW SOFT GRID MAT (FF21).
<br />6.
<br />PATCH, REPAIR, AND PAINT WALLS (PT20).
<br />7.
<br />CLEAN GLASS BY ENTRANCE AND STOREFRONT..
<br />37943 OLAND BLVD.
<br />ZEPHYRHILLS, FL 33542
<br />PROJECT TYPE FEET / ADA
<br />DEAL TYPE N/A
<br />C��M�\•�i �kL ALA
<br />CJA
<br />Robert Reid Wedding.
<br />Architects & Planners, AIA, Inc.
<br />4112 Cypress Street - Tampa, Forida 33607 - 813-879-8998
<br />612 SmM MMtary Tral - Deerfield Beach, Fbrkla 33 - %4-492-9980
<br />Florida License We. ArchitectraaUlmerbr Dear: AA-0001123 - Enghreerbg: 00002655
<br />CONSULTANT
<br />SE&. -
<br />61 E
<br />Keith F. Silas
<br />AR0012923
<br />REVISIONS:
<br />06/06/18 REV1 REMOVAL OF AUDIOLOGY
<br />DRAWING BY: RK/KS/BO
<br />DATE: 04/23/2018
<br />JOB NUMBER: 18027
<br />TITLE:
<br />SCOPE OF WORK
<br />SHEET NUMBER:
<br />COMMENTS:
<br />A-O,,1
<br />APPROVED
<br />
|