4330 20th St (52) - Laserfiche WebLink

Browse Search

GENERAL NOTES PIPING A. WHERE TRAPEZE PIPE HANGERS ARE PROVIDED, UTILIZE DOUBLE NUT U-BOLTS. U-BOLTS SHALL BE LOOSELY FASTENED. INTENT IS NOT TO BIND OR HOLD PIPE, BUT ONLY TO PROVIDE LATERAL SEPARATION. B. PROVIDE WATER HAMMER ARRESTORS FOR FLUSH VALVE FIXTURES AND WHERE QUICK CLOSING VALVES ARE INSTALLED IN ACCORDANCE WITH PDI STANDARDS OR RECOMMENDATIONS. D THIS INCLUDES ALL SENSOR OPERATED FAUCETS. C. PRIME AND PAINT ALL OUTSIDE PIPE AND PIPE SUPPORTS IF THEY ARE NOT GALVANIZED OR STAINLESS STEEL. D. PRIME AND PAINT ALL GAS PIPING LOCATED INSIDE OR OUTSIDE THE BUILDING PER PROJECT SPECIFICATIONS. E. NO PIPE SUPPORT SYSTEMS SHALL CRUSH THE INSULATION WHEN RESTING UPON THE SUPPORT. THE USE OF PIPE SADDLES IS NECESSARY WHEN THE WEIGHT OF PIPE EXCEEDS THE WEIGHT SUPPORT LIMIT OF THE INSULATION. F. PIPE SIZES MAY BE SHOWN FOR SAME PIPE ON MORE THAN ONE PLAN. IN CASE OF PIPE SIZE DISCREPANCY THE LARGER PIPE SIZE SHALL BE CONSIDERED CORRECT DURING THE BIDDING AND DURING CONSTRUCTION UNLESS SPECIFICALLY APPROVED BY THE ARCHITECT/ENGINEER OTHERWISE. G. PROVIDE PIPE SUPPORTS FOR ROOFTOP PIPING, I.E. CONDENSATE DRAINS, GAS PIPING, STORM DRAINAGE, ETC. H. PROVIDE SHUT-OFF VALVES FOR BOTH HOT AND COLD DOMESTIC WATER FOR EACH TOILET BATTERY. LOCATE VALVES IN AN ACCESSIBLE LOCATION WITH ACCESS DOOR AS REQUIRED. I. PROVIDE SHUT-OFF VALVES FOR ALL PRESSURE PIPING CONTAINING TWO (2) OR MORE FIXTURE CONNECTIONS OR BRANCH RUNOUTS. LOCATE VALVES IN AN ACCESSIBLE LOCATION WITH ACCESS DOOR AS REQUIRED. J. PROVIDE WARNING TAGS ON MEDIUM PRESSURE GAS (1/2" TO 5 PSIG) UPSTREAM OF GAS REGULATORS STATING PRESSURE C AND "DO NOT REMOVE". K. PROVIDE PIPE LABELING AS SPECIFIED. F, 7 I 6 PLUMBING A. ALL WORK AND MATERIALS SHALL BE PERFORMED AND INSTALLED IN COMPLIANCE WITH ALL APPLICABLE CODES AS ADOPTED AND AMENDED BY THE INSPECTING AUTHORITY. NOTHING IN THESE DRAWINGS IS TO BE CONSTRUED TO PERMIT WORK NOT CONFORMING TO THESE CODES. B. EXACT LOCATIONS AND MOUNTING HEIGHTS OF PLUMBING FIXTURES SHALL BE OBTAINED FROM THE ARCHITECTURAL DRAWINGS. C. ALL PLUMBING WORK SHALL BE INSTALLED TO AVOID INTERFERENCE WITH ELECTRICAL AND MECHANICAL EQUIPMENT AND STRUCTURAL FRAMING. D. BEFORE COMMENCEMENT OF WORK, CONTRACTOR SHALL VERIFY THE EXACT LOCATIONS, ELEVATIONS AND CHARACTERISTICS OF ALL UTILITIES AND PIPING. CONTRACTOR SHALL ALSO NOTIFY THE ARCHITECT/ENGINEER OF ANY DISCREPANCIES. E. ALL WASTE AND VENT PIPING 3" TO 6" IS TO SLOPE AT A MINIMUM OF 1/8" PER FOOT UNLESS INDICATED OTHERWISE. F. ALL VENT PIPING SHALL BE ATTACHED TO WALL NO FURTHER THAN 3- 0" AWAY. G. PROVIDE ADDITIONAL ATTACHMENT TO WALL FOR ALL FLOOR STANDING SINKS. H. ELECTRICAL OUTLETS SHALL BE INSTALLED BEHIND ELECTRIC WATER COOLERS (NOT EXPOSED). I. FCO'S SHALL BE INSTALLED FLUSH TO FINISHED FLOOR. NO DISHING PERMITTED. J. ALL FLOOR DRAINS LOCATED IN TOILET ROOMS, MECHANICAL ROOMS AND OTHER LOCATIONS NOT SUBJECT TO PERIODIC WASHDOWN SHALL BE PROVIDED WITH TRAP PRIMERS. K. ALL VENT PIPING LOCATED IN A RETURN AIR PLENUM SHALL BE CAST IRON. L. ALL VENT PIPING SHALL BE FULL LINE SIZE IF A WCO IS SHOWN, OR AS DIRECTED BY LOCAL, STATE CODES. M. FLOOR DRAIN LINE SIZE AND VENTING SHALL BE IN ACCORDANCE WITH PLUMBING CODE HAVING JURISDICTION, COMBINATION WASTE AND VENT SYSTEM. N. ALL FLOOR DRAINS SHALL BE INSTALLED FLUSH WITH FINISHED FLOOR. PLUMBING CONTRACTOR SHALL EXAMINE ARCHITECTURAL AND STRUCTURAL DRAWINGS TO DETERMINE THE EXACT TYPE OF FLOOR FINISH AND MAKE ALLOWANCE DURING THE INSTALLATION. IF ANY DRAIN IS NOT FOUND TO BE FLUSH WITH THE FINISHED FLOOR OR PARALLEL TO THE WALLS THE PLUMBING CONTRACTOR WILL BE REQUIRED TO REMOVE SUCH DRAIN AND RE -INSTALL AT NO COST. 0. ALL PIPING SHALL BE LOCATED WITHIN STUD WALLS AND OTHER WALL CONSTRUCTION THAT MAY BE USED TO ENCLOSE THE PIPING. NO PIPING IS TO BE LOCATED IN MASONRY WALLS. PIPING SHOWN ON THE DRAWINGS MAY NOT REFLECT THIS INSTALLATION METHOD BECAUSE OF THE DEGREE OF DETAIL INCONSISTENT WITH SCALED DRAWINGS. IF PIPING CANNOT BE INSTALLED WITHIN THESE STRUCTURES THE APPROVAL OF THE ENGINEER OF ANOTHER INSTALLATION METHOD IS REQUIRED. P. ALL PLUMBING FIXTURE VENTS SHALL TERMINATE A MINIMUM OF 12 INCHES FROM ANY VERTICAL SURFACE AND 10'-0" FROM ANY OUTSIDE AIR INTAKES. Q. PLUMBING FIXTURE DESCRIPTION SHALL TAKE PRECEDENCE WHEN THEIR EXISTS A CONFLICT WITH A DESCRIPTION AND MODEL NUMBER. R. PROVIDE FACTORY FORMED "TRUEBRO" PVC JACKET COVERS FOR DRAIN AND SUPPLY PIPING OF ALL LAVATORIES. S. PROVIDE OFFSET DRAIN STRAINER FITTING FOR ALL LAVATORIES. 5 4 3 ABBREVIATIONS: AFF = ABOVE FINISHED FLOOR ANSI = AMERICAN NATIONAL STANDARDS INSTITUTE APPROX. = APPROXIMATE ASJ = ALL SERVICE JACKET AVG = AVERAGE BHP = BRAKE HORSEPOWER BOP = BOTTOM OF PIPE BOS = BOTTOM OF STEEL BOT. = BOTTOM BTU = BRITISH THERMAL UNIT CL = CENTER LINE CFM = CUBIC FEET PER MINUTE CU. FT. = CUBIC FEET CU. IN. = CUBIC INCH DIA.0 = DIAMETER DN = DOWN DWG. = DRAWING E.C. = ELECTRICAL CONTRACTOR EWT = ENTERING WATER TEMPERATURE F = FAHRENHEIT FPS = FEET PER SECOND GA. = GAGE OR GAUGE GAL. = GALLON GALV. = GALVANIZED GPD = GALLONS PER DAY GPH = GALLONS PER HOUR GPM = GALLONS PER MINUTE HOA = HAND - OFF - AUTOMATIC SWITCH HP = HORSEPOWER ID = DIAMETER, INSIDE I.E. = INVERT ELEVATION KW = KILOWATT LF = LINEAR FEET LWT = LEAVING WATER TEMPERATURE MAX. = MAXIMUM MBH = BTU PER HOUR (THOUSAND) MEZZ. = MEZZANINE MIN. = MINIMUM N.C. = NORMALLY CLOSED NG = NATURAL GAS N.O. = NORMALLY OPEN NTS = NOT TO SCALE O.C. = ON CENTER OD = DIAMETER, OUTSIDE OZ = OUNCE P.O.C. = POINT OF CONNECTION PRESS. = PRESSURE PSI = POUNDS PER SQUARE INCH PSIG = PSI GAGE PW = PROCESS WASTE RPM = REVOLUTIONS PER MINUTE SOV = SHUT-OFF VALVE SFU = SUPPLY FIXTURE UNITS SUCT = SUCTION TEMP = TEMPERATURE TYP. = TYPICAL UG = UNDERGROUND VEL = VELOCITY VERT = VERTICAL VOL = VOLUME VTR = VENT THROUGH ROOF W/ = WITH W/ TP = WITH TRAP PRIMER APPLICABLE CODES FLORIDA BUILDING CODE, 2014 EDITION FLORIDA MECHANICAL CODE, 2014 EDITION FLORIDA PLUMBING CODE, 2014 EDITION FLORIDA FIRE PREVENTION CODE, 2014 EDITION FLORIDA FUEL GAS CODE, 2014 EDITION FLORIDA ENERGY CONSERVATION CODE, 201 EDITION ASHRAE 90.12010 ,,��A7-srnq`I�I/rho ff�ANI AEI ,� C PI ADDENDUM #1 04/16/18 HASKELL IIIRMa Wl Avenue • � TM HaNceu comw"rr * STATE ` * Jar*sonvie, Fluids 32 B PI 02/21 /18 202 f�harrolF ceal,�,-,� A j0R#1 02/14/18 Oj(� �•••�QR�Q:.••• C.OPPOR.ATE Eld( i�JEEFRJG c EFIi,E �� i�o••• �G� DRAWN: DESIGN FIRM _ +_,RE TSIDE DFIVE. `,LIITE 100 �7 EV. REVISION DESCRIPTION DRN. REV. DATE REV. REVISION DESCRIPTION DRN. REV. DATE CONTROL NO.: O�00% C,L�PE�. TEXAS 8 7 6 7 5 4 3 2 SCOPE & ASSUMPTIONS: 1 -SCOPE INCLUDES THE ADDITION OF NEW TRENCH DRAINS AND NEW HUB/FLOOR DRAINS ROUTED NEW BELOW GRADE SUMP. PUMPS AND DOWNSTREAM PIPING TO EXISTING PH NEUTRALIZATION STATION BY OTHERS. -BOTH NEW HAND SINKS WILL INDIRECTLY DISCHARGE INTO HUB DRAINS. •TD-2 (160 GPM) AND TD-1 (140 GPM) FLOW CONCURRENTLY. •FD-5 FLOWS AT 20 GPM (ESEWS SUPPLY RATE). -HD-3: AFTER COOLER IS USED FOR BOILER BLOWDOWN 1407 MAX -ALL DRAINS WILL BE INSTALLED WITH P-TRAPS. -SUMP (1000 GALLONS) SHALL BE FULLY 304 STAINLESS STEEL. -PIPING MATERIAL: CPVC COMPRESSED AIR: — — -SCOPE INCLUDES CONNECTION TO EXISTING CA LINE, DROPS BETWEEN DOCK DOORS, AND CONNECTION TO TWO HOSE REEL STATIONS PROVIDED AND INSTALLED BY HASKELL. •3/4" DROPS WILL PROVIDE ADEQUATE SUPPLY TO HOSE REEL STATIONS. -EXISTING COMPRESSED AIR SYSTEM HAS ENOUGH CAPACITY FOR ADDITIONAL CA HOSE REELS -MATERIAL: COPPER (TO MATCH EXISTING) COLD WATER SUPPLY: -SCOPE INCLUDES TYING INTO EXISTING SYSTEM AND ROUTING TO SINKS AND ESEWS. -EXISTING CW HAS ENOUGH CAPACITY FOR THE PROPOSED ADDITIONS. -MATERIAL: COPPER WITH FIBERGLASS INSULATION AND WHITE PVC JACKET. HOT WATER SUPPLY: •SCOP5.4UCLUDES SINKS AND ESEWS INSTANTANEOUS HEATERS. NATURAL GAS: -BELOW GRADE PIPING AND REGULATOR/METER SET DESIGNED, FURNISHED AND INSTALLED BY UTILITY CO. -MECHANICAL CONTRACTOR'S SCOPE INCLUDES CONNECTION FROM REGULATOR/METER SET OUTLET, PIPE PENETRATION THRU WALL AND A VALVE INSTALLED IN THE VERTICAL POSITION. -MATERIAL: SOCKET WELDED SCH 40 CARBON STEEL PAINTED TO MATCH EXISTING SEISMIC DESIGN REQUIREMENTS CATEGORY-B: SEISMIC DESIGN CATEGORY FOR THIS PROJECT IS CATEGORY B. PER ASCE STANDARD, ASCE/SEI 7-05, CHAPTER 13, MECHANICAL AND ELECTRICAL COMPONENTS ARE EXEMPT AND REQUIRE NO SEISMIC SUPPORT OR SEISMIC BRACING. SHT No SHEET NAME REV DATE P-001 PLUMBING LEGEND, ABBREVIATIONS, & NOTES C 04/16/18 P-110 OVERALL PLUMBING FLOOR PLAN C 04/16/18 P-111 ENLARGED PLUMBING FLOOR PLAN - DRAINAGE C 04/16/18 P-121 ENLARGED PLUMBING FLOOR PLAN - UTILITIES C 04/16/18 P-501 PLUMBING DETAILS C 04/16/18 P-601 PLUMBING SCHEDULES C 04/16/18 P-701 PLUMBING RISER DIAGRAMS C 04/16/18 Grand total: 7 GLOSSARY FURNISH: PURCHASE AND DELIVER (EQUIPMENT) TO THE JOB SITE ONLY. INSTALL: PROVIDE ALL MISCELLANEOUS MATERIALS & SERVICES (LABOR & MATERIAL) REQUIRED TO MAKE EQUIPMENT OPERATIONAL. PROVIDE: FURNISH AND INSTALL. REMARKS: INFORMATION PERTAINING TO ALL ITEMS ON A SCHEDULE. NOTES: INFORMATION PERTAINING ONLY TO INDICATED ITEMS ON A SCHEDULE WAREHOUSE EXPANSION ZEPHYRHILLS NATURAL SPRING WATER ZEPHYRHILLS, FLORIDA The Information contained on this document is the sole property of NWNA and may not be copied or disclosed to others unless authorized by NWNA. DATE: I D.M.: I SCALE: 2 PLUMBING LEGEND, ABBREVIATIONS, & NOTES SIZE SHEET NO. D P-001 1 REV. NO. C IV