|
NOTE
<br />ARRANGE ALL WORK THAT REQUIRES POWER INTERRUPTIONS
<br />TO THE STORE TO BE ACCOMPLISHED AFTER NORMAL STORE
<br />BUSINESS HOURS. NOTIFY THE STORE MANAGER AND THE
<br />WALMART CONSTRUCTION MANAGER A MINIMUM OF 48 HOURS
<br />IN ADVANCE OF ALL STORE POWER INTERRUPTIONS. STORE
<br />MANAGER MUST ALLOW FOR POWERING DOWN OF COMPUTER
<br />SYSTEMS, MOVING AFFECTED PRODUCT, MODIFICATION OF
<br />WALMART AFTER-HOURS WORK SCHEDULES, COORDINATION
<br />WITH OTHER TRADES, AND OTHER CRITICAL SCHEDULING
<br />CONCERNS. PROVIDE TEMPORARY POWER AS REQUIRED.
<br />INSTALLATION OF NEW EQUIPMENT SHALL BE COMPLETED AND
<br />THE POWER SYSTEM TESTED AND RE -ENERGIZED PRIOR TO
<br />START OF BUSINESS THE FOLLOWING MORNING NO LATER
<br />THAN A TIME ESTABLISHED BY THE STORE MANAGER AND
<br />THE WALMART CONSTRUCTION MANAGER.
<br />ONE -LINE DIAGRAM LEGEND
<br />NEW EQUIPMENT
<br />EXISTING EQUIPMENT
<br />EQUIPMENT TO BE DEMOLISHED
<br />NOTE:
<br />ALL OF THE ELECTRICAL DEVICES SHOWN ON THE RISER
<br />DIAGRAM ARE EXISTING AND ARE BASED UPON AS -BUILT
<br />DRAWINGS. E.C. SHALL VERIFY THE EXACT EXISTING
<br />CONDITIONS, SIZES AND LOCATIONS OF EQUIPMENT PRIOR TO
<br />ROUGH -IN. THIS RISER IS SHOWN FOR INFORMATIONAL
<br />PURPOSES ONLY AND ANY NEW DEVICES ARE SHOWN IN
<br />BOLD AND ARE NOTED. DURING CONSTRUCTION, THE STORE
<br />SHALL STAY OPEN FOR BUSINESS. ANY NECESSARY POWER
<br />DOWNTIME SHALL BE SCHEDULED AND APPROVED BY
<br />WALMART CONSTRUCTION MANAGER.
<br />PANELBOARD NOTES ()
<br />(1) TERMINATE GROUND ON ISOLATED GROUND BUS.
<br />(2) INSTALL LOCKING DEVICE (LOCK -OFF FOR
<br />MAINTENANCE). LOCKING DEVICE SHALL BE UL LISTED.
<br />MANUFACTURER SHALL MATCH EXISTING PANELBOARD
<br />MANUFACTURER
<br />(3) INSTALL LOCKING DEVICE (LOCK -ON FOR CRITICAL
<br />LOAD).
<br />(4) GFI BREAKER FOR PERSONNEL PROTECTION (5mA).
<br />(5) GFI BREAKER FOR EQUIPMENT PROTECTION (30mA)
<br />(6) CONDUCTOR SIZE HAS BEEN INCREASED FOR VOLTAGE
<br />DROP. SIZE EQUIPMENT GROUNDING CONDUCTOR
<br />PROPORTIONATELY PER NEC.
<br />(7) REFER TO ONE -LINE DIAGRAM FOR AVAILABLE FAULT
<br />CURRENT FOR INTERRUPT RATINGS.
<br />(8) REFER TO ONE -LINE DIAGRAM FOR WIRE SIZES.
<br />(9) FACTORY WIRED TO LOAD.
<br />(10) BREAKER SHALL BE HIGH MAGNETIC TYPE.
<br />(11) NEW PNLBD TO REPLACE EXISTING PNLBD WITH THE
<br />SAME NAME. NEW PNLBD POPULATION WAS
<br />DETERMINED BY ORIGINAL CONSTRUCTION DRAWINGS.
<br />E.C. SHALL VERIFY THAT ALL EXISTING BRANCH
<br />CIRCUITS ARE EXTENDED TO NEW PNLBD LOCATION.
<br />E.C. SHALL VERIFY CONDITION OF EXISTING BRANCH
<br />CIRCUIT CONDUIT AND WIRE TO EXTEND PRIOR TO
<br />USE, TO INSURE THAT THEY MEET ALL U.L. RATINGS
<br />AND REPLACE AS REQUIRED.
<br />(12) ROUTE CIRCUIT THROUGH "SWEATMISER PNLBD"
<br />(13) EXISTING CIRCUIT TO REMAIN.
<br />(14) ROUTE CIRCUIT THROUGH NEW CONTACTOR
<br />(15) PROVIDE INTERLOCK WIRING WITH EXHAUST HOOD
<br />ANSUL SYSTEM.
<br />(16) RELOCATE CIRCUIT FROM EXISTING PANELBOARD.
<br />(17) PROVIDE LUG ADAPTERS AS REQUIRED.
<br />(18) HACR CIRCUIT BREAKER.
<br />(19) EXISTING CIRCUIT BREAKER TO REMAIN. VERIFY
<br />CONDITION OF CIRCUIT BREAKER TO ENSURE THAT IT
<br />IS OPERATIONAL AND MEETS ALL U.L. RATINGS.
<br />(20) ROUTE CIRCUIT THROUGH EXISTING LCU CABINET
<br />UTILIZING EXISTING RELAY AND CONTROLS. UPDATE
<br />LCU IDENTIFICATION SCHEDULE WITH LOAD
<br />IDENTIFICATION.
<br />(21) PROVIDE HANDLE LOCK OFF DEVICE TO LOCK "SPARE"
<br />CIRCUIT BREAKER IN THE "OFF" POSITION. IF
<br />CIRCUIT BREAKER IS IDENTIFIED AS "EXISTING", FIELD
<br />VERIFY CIRCUIT BREAKER INDICATED IS NOT
<br />CONNECTED TO ANY LOAD AND UPDATE PANELBOARD
<br />CIRCUIT DIRECTORY IDENTIFYING CIRCUIT AS "SPARE".
<br />(22) PROVIDE U.L. LISTED OVERCURRENT DEVICE TO
<br />COORDINATE AND MAINTAIN MANUFACTURER'S SERIES
<br />RATED SYSTEM.
<br />(23) SOLENOID OPERATED CIRCUIT BREAKER. REFER TO
<br />ENERGY MANAGEMENT PLANS FOR CIRCUIT BREAKER
<br />CONTROL.
<br />(24) TRACE EXISITING CIRCUIT, IDENTIFY LOAD AND
<br />PROVIDE COMPLETE TYPEWRITTEN PANELBOARD
<br />IDENTIFICATION SCHEDULE AND PLACE ON INTERIOR
<br />OF PANELBOARD DOOR. IF CIRCUIT IS A "SPARE"
<br />THEN REFER TO PANELBOARD NOTE (21).
<br />(25) PROVIDE LISTED HANDLE -TIE BETWEEN CIRCUIT
<br />BREAKERS SHARING COMMON NEUTRAL FOR
<br />SIMULTANEOUS TRIP.
<br />(26) PROVIDE BLANK CIRCUIT BREAKER FILLER PLATE FOR
<br />EXPOSED SPACE IN PANELBOARD.
<br />GENERAL NOTES:
<br />1. E.C. SHALL ADD OR REARRANGE CIRCUIT BREAKERS
<br />WITHIN PANELBOARDS AS REQUIRED TO MATCH NEW
<br />CIRCUIT DESIGNATIONS SHOWN ON DRAWINGS.
<br />2. NEW OVERCURRENT PROTECTIVE DEVICES PLACED IN
<br />EXISTING PANELBOARDS OR DISTRIBUTION BOARDS SHALL
<br />MATCH THE TYPE AND AIC RATING OF EXISTING
<br />OVERCURRENT PROTECTION DEVICES IN SAID BOARD.
<br />3. E.C. SHALL TRACE ALL ELECTRICAL CIRCUITS FOR ALL
<br />EXISTING ELECTRICAL PANELBOARDS AFFECTED BY THE
<br />REMODEL AND IDENTIFY LOADS ON EACH CIRCUIT.
<br />PROVIDE A COMPLETE TYPEWRITTEN PANELBOARD
<br />IDENTIFICATION SCHEDULE FOR ALL AFFECTED
<br />PANELBOARDS.
<br />4. ALL OVERCURRENT DEVICES ARE NEW UNLESS NOTED
<br />OTHERWISE.
<br />20A WIRE SIZING SCHEDULE
<br />ALL WIRE SIZES SHOWN ON PANEL SCHEDULES ARE
<br />INTENDED TO BE MINIMUM ACCEPTABLE WIRE SIZE.
<br />THE FOLLOWING SCHEDULE IS TO BE USED TO SIZE
<br />WIRE FOR 20 AMP CIRCUITS (120 AND 277 VOLT).
<br />LENGTHS (IN FEET) ARE INTENDED TO BE MAXIMUM.
<br />-120 VOLT
<br />#12
<br />#10
<br />#8
<br />#6
<br />1-5 AMPS
<br />200 FT.
<br />325 FT.
<br />�490 FT.
<br />770 FT.
<br />6-10 AMPS
<br />100 FT.
<br />160 FT.
<br />245 FT.
<br />385 FT.
<br />11-15 AMPS
<br />70 FT. _
<br />110 FT.-
<br />I 165 FT. _
<br />255 FT.
<br />277 VOLT
<br />.,..._..#12
<br />#1.0 ..�.._w..
<br />#8....._...__.
<br />__......#6.w__.._....
<br />1-5 AMPS
<br />480 FT.
<br />760 FT.
<br />FT.
<br />1865 FT.
<br />6-10 AMPS
<br />240 FT.-
<br />380 FT.
<br />_1170
<br />585 FT.
<br />930 FT.-
<br />11-15 AMPS
<br />160 FT.
<br />250 FT.
<br />390 FT.
<br />-620 FT.
<br />LLQ NEW
<br />SERVES: LIQUOR SALES
<br />LOCATION: LIQUOR STOCKROOM
<br />MOUNTING: SURFACE
<br />DESCRIPTION
<br />1 FRONT CASH REGISTER
<br />3 ICE MERCHANDISER
<br />5 EXHAUST FAN
<br />7 EWC (4)
<br />9 HAND DRYER (2,6)
<br />11 HAND DRYER (2,6)
<br />1-11
<br />0 R OP R�T,W a
<br />15 SHOW WINDOW RCPT (6
<br />17 EAS SYST M 3
<br />19 COOLER DOOR LTG (14)
<br />2E1-
<br />2TROOM LIGHTING
<br />25 CAR CHARGER (2)
<br />2
<br />2 CAR CHARGER (2)
<br />31
<br />3 °� CAR CHARGER (2)
<br />35
<br />37
<br />39 SPACE
<br />41 SPACE
<br />PER NEC ARTICLE 220
<br />33,915
<br />ELECTRICAL
<br />ROOM #1
<br />ELECTRICAL
<br />ROOM #3
<br />WIRE
<br />BRKR
<br />PL
<br />KVA A
<br />30
<br />30
<br />30
<br />1
<br />1
<br />1
<br />0.50
<br />3.64
<br />10
<br />10
<br />20
<br />20
<br />20
<br />1
<br />1
<br />1
<br />0.48
<br />0.20
<br />10
<br />20
<br />1
<br />20
<br />20
<br />1
<br />1a
<br />0.24
<br />1.80
<br />8
<br />8
<br />40
<br />40
<br />2
<br />2
<br />3.12
<br />1.20
<br />3.12
<br />o • VA
<br />KVA B
<br />1.55 1 3.64
<br />1.15 1 0.86
<br />11 lill we] w
<br />3.12
<br />,3
<br />CONTACTOR SCHEDULE
<br />LABEL A S S H 0 WN...,,,.,.........
<br />.,,.w.,,...°...._,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,....
<br />....,,,,,.........,,, ........
<br />....
<br />. ..............
<br />.-._..._...�........,�..,.,_.,.....�......_...,,,.,._A. .,.._...,,._.,_...,.,,,.,.._....,,..,.n.__.. .,,,,,. ®.m.............°...mm._ ..,,,...°,.,,.,
<br />ENCLOSURE COIL CONTACTS NOTES
<br />208Y/120V, 3PH, 4W
<br />150A MCB N0. LOAD SERVED _ VOLTS
<br />C1 LIQUOR NEMA-1 120V 600V1
<br />MECHANICALLY
<br />SALES LIGHTING 20A-4P HELD
<br />EQUIPMENT GROUND BUS
<br />NOTE: REFER TO SHEET EM1 FOR EMS CONTROL INFORMATION.
<br />ISOLATED GROUND BUS
<br />KVA C
<br />PL
<br />BRKR
<br />WIRE
<br />DESCRIPTION
<br />3
<br />50
<br />8
<br />CU-1
<br />30.3A, 208/3
<br />2
<br />4
<br />6
<br />0.53
<br />3.64
<br />1
<br />1
<br />1
<br />20
<br />20
<br />20
<br />COOLER DOOR POWER
<br />CLR FANS(CU-1 a&CU-1 b)(2)
<br />JANITOR RECEPTACLE
<br />8
<br />10
<br />12
<br />1.15
<br />0.18
<br />1
<br />1
<br />1
<br />20
<br />20
<br />1 20
<br />STCKRM & RTU RCPT/BUZZ.
<br />CU-2 CASE FANS (2)
<br />CU-2 CASE LIGHTS (2,14)
<br />14
<br />16
<br />18
<br />_0 54
<br />0.34
<br />w- -
<br />3
<br />25
<br />_ _
<br />10
<br />_
<br />CU-2
<br />15.9A,_.208 -3 -- _ _ _
<br />20
<br />22
<br />24
<br />Q_15_
<br />1..80._
<br />3.12
<br />1
<br />1
<br />TOTAL 15.68 17.38 15.43
<br />131 145 129
<br />TOTAL LOAD 48.49 KVA 135
<br />FEEDER LOAD 43.74 KVA 121
<br />EXISTING
<br />UTILITY TRANSFORMER
<br />480Y/277V, 30, 4W SEC
<br />EXISTING DISTRIBUTION SYSTEM IS
<br />SERIES RATED. E.C. SHALL PROVIDE
<br />CIRCUIT BREAKER(S) THAT WILL
<br />MAINTAIN EXISTING MANUFACTURER'S
<br />U.L. LISTED SERIES RATED SYSTEM.
<br />MSB1 EXISTING
<br />4000 AMPS 480Y/277V 30 4W
<br />CT 800A C 600A
<br />ETR \� ETR
<br />1
<br />1
<br />20
<br />20
<br />NEON COOLER SIGN
<br />ROLL UP DOOR
<br />2
<br />30
<br />0.86
<br />1
<br />1
<br />A E
<br />SPACE
<br />SPACE
<br />34
<br />36
<br />1
<br />1
<br />1
<br />SPACE
<br />SPACE
<br />SPACE
<br />38
<br />40
<br />42
<br />KVA
<br />AMPS
<br />AMPS
<br />AMPS
<br />DRY TYPE TRANSFORMER
<br />SCHEDULE
<br />A R Y .,... ....a__
<br />._......®..�SE..�-._._
<br />CONDARY
<br />MOUNTING LOCATION
<br />VOLTS PHASE WIRES
<br />_
<br />VOLTS PHASE WIRES
<br />MOUNT AT BAR JOIST
<br />TLLQ
<br />45
<br />480V 3PH 3W
<br />120/208V 3PH 4W
<br />NOTES A,B,C,D
<br />WITH TAPS
<br />DRY TYPE °TRANSFORMER NOTES:
<br />A. GROUND IN ACCORDANCE WITH NEC 250-30.
<br />B. TRANSFORMERS SHALL BE 150 DEC C RISE, MAXIMUM, WITH ANSI/NEMA
<br />MAXIMUM SOUND LEVELS.
<br />C. CLEARANCE FOR VENTILATING OPENINGS SHALL BE NO LESS THAN THAT
<br />REQUIRED ON MANUFACTURERE'S NAMEPLATE. NEC 110-13(B),
<br />450-9 AND 450-11.
<br />D. EQUIPMENT SHALL BE MANUFACTURED BY CUTLER -HAMMER, SIEMENS
<br />OR SQUARE D.
<br />COORDINATE ALL CHANGES TO EXISTING ELECTRICAL SERVICE
<br />AND METERING WITH UTILITY COMPANY.
<br />STORE ADDRESS: WALMART LBA
<br />7631 GALL BLVD.
<br />ZEPHYRHILLS, FL 33541
<br />UTILITY COMPANY: TAMPA ELECTRIC COMPANY
<br />PHONE: 813 635-1500
<br />IF IT IS NECESSARY TO REMOVE A METER, RTU
<br />SERVER, CT OR DISRUPT THE COMMUNICATION OF THE
<br />SYSTEM, THE CONTRACTOR IS RESPONSIBLE TO
<br />RESTORE THE SYSTEM TO THE SAME LEVEL OF
<br />OPERATION THAT EXISTED PRIOR TO THE WORK BEING
<br />INITIATED. THE EXISTENCE AND FUNCTIONALITY OF THE
<br />SYSTEM SHALL BE VERIFIED BY CALLING WALMART
<br />BUILDING PERFORMANCE TEAM AT 479-204-0452
<br />BETWEEN THE HOURS OF 7 AM UNTIL 5 PM CT.
<br />EXISTING
<br />EXISTING
<br />EXISTING
<br />PNLBD
<br />PNLBD
<br />PNLBD
<br />H1B2
<br />H4B
<br />H4C
<br />30Y/277V
<br />80Y/277V
<br />80Y/277
<br />EXISTING
<br />PNLBD
<br />H3B
<br />80Y/277
<br />NEW
<br />PNLBD
<br />L.3B
<br />8Y/120
<br />16.477
<br />(70A-3P)
<br />3Dtj 4
<br />50KVA
<br />•80V E2
<br />UXSTING11 )
<br />EXISTING
<br />PNLBD
<br />L3D1
<br />208Y/120V
<br />UPS
<br />SYSTEM
<br />NEW
<br />PNLBD
<br />L1 U
<br />08Y/120V
<br />J ... leLeaaI«.L >,oM ..
<br />GR SIDE PARTIAL ONE -LINE
<br />NTS
<br />CABLE WHIPS OUT OF POWER POLE SHALL BE INSTALLED IN
<br />A NEAT AND WORKMAN -LIKE MANNER. ROUTE CABLE WHIPS
<br />TO TERMINATIONS ALONG UNISTRUT OR STRUCTURE AND
<br />SUPPORT EVERY 12" TO 24". EXCESS CABLE SHALL BE
<br />TIGHTLY COILED AND ATTACHED TO UNISTRUT OR JOIST.
<br />12" PVC SLEEVE
<br />2-1/2" UNISTRUT
<br />STRAP FIRMLY CLAMPED
<br />TO CONDUIT -�
<br />POWER POLE
<br />2-1/2' INSET j
<br />PVC
<br />CONDUIT
<br />INSET: CLAMP A 12" LENGTH
<br />OF PVC CONDUIT AND RUN THE
<br />POWER POLE THROUGH ITS CENTER
<br />NO CONNECTION OF ANY KIND SHALL BE MADE
<br />TO JOIST WEB MEMBERS, JOIST BRIDGING, OR
<br />ROOF DECK. MAINTAIN MINIMUM 6" CLEARANCE
<br />FROM TOP OF POWER POLE TO ROOF DECK.
<br />REF MANUFACTURER'S "GENERAL
<br />FITTINGS SPECIFICATIONS" FOR
<br />DESIGN BOLT TORQUE.
<br />EXTEND POWER POLE 3"
<br />MIN ABOVE CL OF UNISTRUT
<br />INSTALL CEILING FLANGE
<br />PROVIDED WITH POLE FOR
<br />STORES WITH LAY -IN CEILING
<br />CONTRACTOR SHALL ATTACH POWER
<br />POLE TO CHECKOUT STAND PER
<br />MANUFACTURER RECOMMENDATIONS
<br />UNISTRUT----
<br />Voltage Drop Calculations: FBC-EC 2010
<br />Voltage Drop Calculations:
<br />VOLTAGE DROP CALCULATIONS HAVE BEEN
<br />PERFORMED, THIS DESIGN COMPLIES WITH
<br />VOLTAGE DROP REQUIREMENTS OF FBC
<br />ENERGY CONSERVATION 505.7.3. OF FEEDER
<br />(< 2%) AND BRANCH (<3%) CIRCUITS.
<br />Y/120V
<br />H4B IS 104'
<br />AWAY IN EDC4
<br />AND HAS A
<br />VOLTAGE DROP
<br />OF 0.63
<br />LLQ IS 9'
<br />AWAY IN AND
<br />AND HAS A
<br />VOLTAGE DROP
<br />OF 0.11
<br />NEW C1 1 .29
<br />PNLBD REF: 2-EM1
<br />"'°' INSTALL IN 5"X8"X4" NEMA-1
<br />LLQ ENCLOSURE WITH NAMEPLATE
<br />08Y/120V INDICATING "CONTACTOR
<br />CONTROL XFMR".
<br />LIQUOR STOCKROOM
<br />DIAGRAM
<br />PROVIDE UNISTRUT PER
<br />SPECIFICATIONS. LENGTH AS
<br />REQUIRED TO SPAN JOISTS.
<br />SECURE TO BOTTOM CHORD
<br />OF BAR JOIST.
<br />PROVIDE 1 /4" BOLT
<br />AND 1-1/4" FENDER
<br />WASHER TYP
<br />PROVIDE UNISTRUT
<br />P1026 ANGLE
<br />FITTING OR EQUAL
<br />' PROVIDE 1-1/4" '�BOTTOM
<br />FENDER WASHER, LOCK INSET CHORD OF
<br />WASHER AND NUT, TYP BAR JOIST
<br />INSET: MOUNT UNISTRUT ABOVE BOTTOM CHORD OF BAR
<br />FINISHED JOISTS USING 1 /4" BOLTS, WITH FENDER WASHERS AND
<br />FLOOR LOCK WASHERS BETWEEN BOLT HEAD AND JOIST FLANGE
<br />L
<br />1 /8" = 1'-0"
<br />H1A H1B1 H1B2
<br />ELECTRICAL MSWB
<br />ROOM #1 L1 D2-19,21
<br />H1P2 16.470�
<br />TD2 L1 D H1 P1 16.501
<br />jI
<br />EXISTING FIRE
<br />ALARM BOARD
<br />ALARM POWER
<br />A WARNING
<br />ARC FLASH AND SHOCK HAZARD.
<br />APPROPRIATE PERSONAL PROTECTIVE
<br />EQUIPMENT (PPE) REQUIRED.
<br />NOTES:
<br />A. ALL SWITCHBOARDS AND PANELBOARDS SHALL
<br />HAVE A COMMERCIALLY PRODUCED PERMANENT LABEL
<br />APPLIED, SIMILAR TO THE ABOVETO WARN OF
<br />POTENTIAL ARC FLASH HAZARDS,, IN ACCORDANCE
<br />WITH NEC 110.16 AND NFPA 70E.
<br />B. LABELING MAY BE COMPLETED BY EQUIPMENT
<br />MANUFACTURER, EQUIPMENT VENDOR/SUPPLIER, OR
<br />THE CONTRACTOR. THE CONTRACTOR SHALL VERIFY
<br />THAT ALL SWITCHBOARDS AND PANELBOARDS ARE
<br />PROPERLY LABELED IN THE FIELD.
<br />ARC FLASFI_QE -1 1
<br />L
<br />5 NTS 02.17.06 WREP44
<br />PROVIDE SEISMIC
<br />BRACING AS REQUIRED
<br />BY STATE OR LOCAL
<br />ORDINANCES.
<br />SUSPEND STEEL ANGLES
<br />FROM BAR JOIST WITH
<br />1/2" THREADED STEEL;
<br />ROD AS REQUIRED TO
<br />MAINTAIN CLEAR SPACE j
<br />IN FRONT OF I
<br />TRANSFORMER PER NEC!
<br />REQUIREMENTS, TYP.
<br />1/2" THREADED STEEL ROI
<br />DRILL 5/8" HOLES THROUC
<br />ANGLES AND INSTALL LOCH
<br />WASHERS AND NUTS ON E
<br />SIDE, TYP.
<br />6'-0" MAXIMUM SPACING
<br />:1 SU�SPENDED �TR
<br />Y / iris
<br />..••� -
<br />III
<br />I'paw,
<br />I pm
<br />COORDINATE EXACT LOCATION
<br />WITH STORE SETUP SUPERVISOR
<br />PRIOR TO INSTALLATION.
<br />n LIOUOR
<br />POWER PLAN
<br />UC11431Nl7 UINI I,
<br />OF 2.
<br />CIRCUIT SCHEDULE GENERAL POWE
<br />R NOTES
<br />73 70A, (3)#4, (1)#8G, 1" C 1. TELEPOWER POLE(S): MOUNT JUNCTION BOX(ES) TO TOP
<br />155 150A, (4)#1 /0, (1)#6G, (1)#6 IG, 2" C SIDE OF BOTTOM CHORD OF BAR JOIST. INSTALL
<br />FURNISHED PRE -WIRED POWER POLE AND TERMINATE
<br />G150 GND, #6 COPPER GROUND, 3/4" C PROVIDED FLEXIBLE CONDUIT AND WIRING TO JUNCTION
<br />BOX. PROVIDE UNISTRUT SUPPORTS AND HARDWARE TO
<br />ALL CONDUCTOR SIZES ARE BASED ON 75 DEG C SECURE TELEPOWER POLE PLUMB TO BUILDING
<br />RATED TERMINATIONS AND TYPE THHN/THWN-2 STRUCTURE.
<br />INSULATION; FOR TERMINATIONS OR INSULATION TYPES 2. PROVIDE LIQUID -TIGHT FLEXIBLE METAL CONDUIT AND
<br />RATED LESS THAN 75 DEG C, MODIFY SIZES WIRING FROM DISCONNECT SWITCH OR JUNCTION BOX TO
<br />ACCORDING TO NFPA 70. EQUIPMENT KNOCKOUT OR ELECTRICAL CONNECTION
<br />POINT.
<br />LOW VOLTAGE WIRING 3. WHERE EQUIPMENT NAMEPLATE PROTECTIVE DEVICE
<br />RATING DIFFERS FROM SIZE PROVIDED, CHANGE OUT
<br />BRANCH CIRCUIT WIRING AND OVERCURRENT DEVICE TO
<br />APPROPRIATE RATING PER NEC.
<br />ALL LOW VOLTAGE WIRING AND CABLE IS REQUIRED TO BE 4. ELECTRONIC FIRE PROTECTION/SECURITY ALARM BOXES
<br />PLENUM RATED. COORDINATE PROPER CABLE TYPES AND CONDUITS SHOWN ON POWER PLANS SHALL BE
<br />REQUIRED WITH WAL-MART ALARM DIVISION AND WAL-MART PROVIDED UNDER THIS CONTRACT. IN ADDITION, UNLESS
<br />CONSTRUCTION MANAGER PRIOR TO INSTALLATION. NOTED OTHERWISE, THE FOLLOWING GENERAL NOTES
<br />APPLY:
<br />A. ALL ALARM JUNCTION BOXES SHALL BE
<br />4"X4"X2-1/8" MINIMUM.
<br />B. ALARM RACEWAYS SHALL BE 3/4" MINIMUM WITH
<br />PULL WIRE AND INSULATING BUSHINGS AT END OF
<br />VERTICAL RACEWAY RUN.
<br />C. VERTICAL RACEWAYS FROM ALARM BOXES SHALL BE
<br />EITHER CONCEALED INSIDE WALL OR SURFACE
<br />MOUNTED (TO MATCH JUNCTION BOX MOUNTING). ALL
<br />VERTICAL RUNS SHALL BE TURNED 90-DEGREES AT
<br />TOP SIDE OF BOTTOM CHORD OF BAR JOIST AND
<br />EXTENDED HORIZONTALLY TO A LOCATION ACCESSIBLE
<br />BY VERTICAL FLOOR TYPE LIFT.
<br />5. UPON COMPLETION OF ELECTRICAL INSTALLATION AND
<br />PRIOR TO ENERGIZING CIRCUIT:
<br />,.r..... ,, r�.�$°��A °°, E�°„�°_. � ��,,- A. INSPECT WIRE AND CABLE FOR PHYSICAL DAMAGE.
<br />B. PERFORM CONTINUITY TEST.
<br />C. VERIFY PROPER PHASING CONNECTION TO ALL THREE
<br />3"x2"x1/4" STEEL ANGLES PHASE MOTOR LOADS.
<br />BETWEEN BAR JOIST ON EACH SIDE
<br />TRANSFORMER. MOUNT (WHERE WI ELECTRICAL KEYNOTES
<br />WITHIN 4" OF PANEL POINT WHEERE
<br />WEB BRACING ATTACHES TO BOTTOM
<br />CHORD). BOLT OR CLAMP ANGLES
<br />TO BAR JOIST. DO NOT CUT OR 16.226 ELECTRICAL ARTICLE SURVEILLANCE SYSTEM:
<br />DRILL HOLES IN BAR JOIST. PROVIDE 3/4" CONDUITS (WITH PULL WIRE)
<br />FROM EAS POWER MODULE TO EAS
<br />PEDESTAL LOCATION AS SHOWN ON PLANS,
<br />BAR JOIST WITH OVERALL LENGTH OF EACH CONDUIT
<br />NOT TO EXCEED 36'. STUB CONDUITS 3"
<br />j ABOVE FINISHED FLOOR AT EAS PEDESTAL
<br />LOCATION AND EXTEND CONDUIT UP WALL
<br />TO HEIGHT OF THE EAS RECEPTACLE,
<br />TRANSFORMER PROVIDE BUSHINGS AT EACH END.
<br />16.227 ELECTRIC WATER COOLER RECEPTACLE:
<br />CEILING MOUNTING BRACKETS AS CONCEAL WITHIN CABINET PER MANUFACTURERS
<br />FURNISHED BY TRANSFORMER REQUIREMENTS.
<br />MANUFACTURER OR USE 2"x2"xl/4"
<br />ANGLES. BOLT TRANSFORMER TO 16.232 AUTOMATIC DOOR OPERATOR: VERIFY LOCATION
<br />BRACKETS OR ANGLES. WITH MANUFACTURER'S RECOMMENDATIONS PRIOR
<br />TO INSTALLATION. ALL CONDUIT AND WIRING
<br />SHALL BE CONCEALED AT MAIN ENTRANCE DOORS.
<br />FORMERMOUNTING 16.233 ROOF TOP UNIT IS PROVIDED WITH A HACR
<br />EP21 a RATED CIRCUIT BREAKER AND GFI DUPLEX
<br />RECEPTACLE.
<br />16.238 CONTRACTOR SHALL PROVIDE A 1/2" FLEXIBLE
<br />CONDUIT WITH PULL STRING ROUTED FROM CEILING
<br />SPACE BELOW UP THROUGH THE NEW CURB
<br />ADAPTER, PENETRATING THE BOTTOM OF THE RTU'S
<br />ELECTRICAL COMPARTMENT. THIS RACEWAY IS
<br />REQUIRED FOR FUTURE FIRE ALARM COMMUNICATION
<br />CABLING BY OTHERS.
<br />16.243 INSTALL MANUFACTURER FURNISHED JUNCTION
<br />BOX ABOVE DOOR HEADER FOR CAMERA CABLING.
<br />PROVIDE 1" CONDUIT (WITH PULL WIRE) FROM
<br />JUNCTION BOX TO STRUCTURE. TERMINATE AT
<br />BAR JOIST WITH BUSHINGS. COORDINATE
<br />INSTALLATION WITH MANUFACTURER'S
<br />IDE REQUIREMENTS.
<br />a
<br />TI 16 299 INSTALL EMS 120V/24VAC TRANSFORMER.
<br />WIT CONNECT TO 120V RECEPTACLE CIRCUIT WITH
<br />(2)#12, (1)#12G. COORDINATE INSTALLATION
<br />AND PROCUREMENT WITH EMS CONTRACTOR.
<br />REFER TO EMS PLAN INDICATED.
<br />0
<br />--- 16.470 FURNISH AND INSTALL NEW 20 AMP, 120 VOLT
<br />CIRCUIT(S). FEED FROM PANELBOARD AS
<br />INDICATED. PROVIDE 20A-1P CIRCUIT BREAKER
<br />IF NEEDED. E.C. SHALL MATCH MANUFACTURER,
<br />° TYPE AND AIC RATINGS OF EXISTING CIRCUIT
<br />BREAKERS. E.C. SHALL VERIFY PRIOR TO
<br />ROUGH -IN THAT EXISTING PANELBOARD HAS
<br />° SPARE CAPACITY TO ACCOMMODATE ADDITIONAL
<br />LOAD.
<br />16.471 FURNISH AND INSTALL NEW 20 AMP, 120 VOLT
<br />ISOLATED GROUND CIRCUIT(S). FEED FROM PANEL
<br />BOARD AS INDICATED. PROVIDE 20A-1P CIRCUIT
<br />BREAKER IF NEEDED. E.C. SHALL MATCH
<br />MANUFACTURER, TYPE AND AIC RATINGS OF
<br />EXISTING CIRCUIT BREAKERS. PROVIDE ORANGE
<br />ROUGH -IN THAT EXISTING PANELBOARD HAS SPARE
<br />COVER PLATES ON ALL ISOLATED GROUND DEVICES
<br />WITH CIRCUIT NUMBER ENGRAVED UNLESS NOTED
<br />OTHERWISE. E.C. SHALL VERIFY PRIOR TO
<br />CAPACITY TO ACCOMMODATE ADDITIONAL LOAD.
<br />16.472 FURNISH AND INSTALL NEW CIRCUIT
<br />BREAKER (##A-#P) IN EXISTING PANELBOARD
<br />INDICATED. E.C. SHALL MATCH MANUFACTURER,
<br />TYPE AND AIC RATINGS OF EXISTING CIRCUIT
<br />BREAKERS. E.C. SHALL VERIFY PRIOR TO
<br />ROUGH -IN THAT EXISTING PANELBOARD HAS
<br />SPARE CAPACITY TO ACCOMMODATE
<br />ADDITIONAL LOAD.
<br />FURNISH AND INSTALL NEW CIRCUIT
<br />16 --�---- .477
<br />BREAKER (##A-#P) IN EXISTING PANELBOARD
<br />INDICATED. PROVIDE CIRCUIT BREAKER LOCKING
<br />DEVICE (LOCK -OFF FOR MAINTENANCE).
<br />BE E.C. SHALL MATCH MANUFACTURER,
<br />\TION TYPE AND AIC RATINGS OF EXISTING CIRCUIT
<br />OR BREAKERS. E.C. SHALL VERIFY PRIOR TO
<br />ITS ROUGH -IN THAT EXISTING PANELBOARD HAS
<br />'ED SPARE CAPACITY TO ACCOMMODATE
<br />ADDITIONAL LOAD.
<br />-° - 16.501 A PROVIDE TWO (2) 20A, 120 VOLT DEDICATED
<br />CIRCUITS AND FINAL CONNECTIONS TO FIRE ALARM
<br />BACKBOARD EQUIPMENT PROVIDED BY OTHERS.
<br />COORDINATE INSTALLATION WITH ALARM INSTALLER
<br />PRIOR TO ROUGH -IN.
<br />16.600 PROVIDE SURFACE MOUNTED ALARM JUNCTION
<br />BOX (WITH VERTICAL RACEWAY) MOUNTED 2"
<br />ABOVE AND 8" IN FROM STRIKE SIDE OF
<br />DOOR FRAME.
<br />16.601 PROVIDE SURFACE MOUNTED ALARM JUNCTION BOX
<br />(WITH VERTICAL RACEWAY) ADJACENT TO AND
<br />EVEN WITH TOP OF DOOR FRAME.
<br />16.610 PROVIDE SURFACE MOUNTED ALARM JUNCTION
<br />BOX (WITH VERTICAL RACEWAY) AT +84"
<br />(UNLESS NOTED OTHERWISE).
<br />16.619 PROVIDE 4"X4"X2-1 /8" RECESSED ALARM
<br />JUNCTION BOX IN CEILING WITH
<br />4"X4"X"1-1/2" EXTENSION RING WITH
<br />-- - RACEWAY ROUTED TO NEAREST ACCESSIBLE
<br />CEILING SPACE.
<br />16.650 CONDUIT SLEEVE: PROVIDE 1-1/2" CONDUIT
<br />SLEEVE WITH BUSHINGS ABOVE BAR JOIST
<br />(UNLESS NOTED OTHERWISE). PROVIDE
<br />TEMPORARY FIRE STOP WITHIN CONDUIT.
<br />DRISTNG CONDIONS WEE TAKEN FROAWIINGS AANDITMAY NOTRREFLECT-EXACTORIGINAL - AATHOROECH UGOHNKNOWLEDGE OFSALOLNDI°RAWINGS ANDING
<br />- ° -- "AS -BUILT" CONDITIONS. CONTRACTOR SHALL FIELD SPECIFICATIONS IN THEIR RELATED FIELD. THE
<br />VERIFY ALL EXISTING CONDITIONS PRIOR TO FAILURE TO ACQUAINT THEMSELF WITH THIS
<br />SUBMITTING FINAL BIDS. CONTRACTOR SHALL KNOWLEDGE DOES NOT RELIEVE THE RESPONSIBILITY
<br />CAREFULLY COORDINATE NEW WORK AND DEMOLITION OF PERFORMING THE WORK PROPERLY. NO
<br />WITH ALL OTHER DISCIPLINES AND EXISTING ADDITIONAL COMPENSATION SHALL BE ALLOWED
<br />CONDITIONS. BECAUSE OF CONDITIONS THAT OCCUR DUE
<br />TO FAILURE TO FAMILIARIZE WORKERS WITH THIS
<br />KNOWLEDGE.
<br />N
<br />O
<br />0 0
<br />0
<br />U
<br />1~ �
<br />a)
<br />I
<br />e
<br />16 a
<br />o
<br />24,
<br />W
<br />R°
<br />U
<br />a
<br />Uj W rw woZ�
<br />Nz� Zwvai�WZ3
<br />W o r-Ep zjoopo-j
<br />O Uajz a �w�Fpo
<br />aN �Qorz�Fa�w�o
<br />z Q L�.
<br />O 3v�04=> �Za�ra
<br />w zO
<br />J Oo
<br />ZJO�
<br />�vJQ �ON_
<br />O
<br />�<�oN
<br />Z=L6U-W�w�OJc� 09-
<br />LI
<br />H SQwdZr9owli3OU' Qor
<br />V) Mv) 0ov=iav)wmxzoa<
<br />z
<br />0
<br />O 0
<br />E_
<br />a
<br />�
<br />aoa
<br />O O
<br />x
<br />0
<br />rrLij
<br />cr
<br />M.�
<br />CD
<br />f--a
<br />0
<br />�+
<br />z
<br />W
<br />�
<br />0
<br />o
<br />O
<br />0
<br />CQ
<br />w
<br />N
<br />44
<br />�
<br />z
<br />0
<br />ISSUE BLOCK
<br />0
<br />PR#1
<br />08/22/14
<br />0
<br />REISSUE
<br />12/04/15
<br />ADD#3
<br />07/11 /16
<br />CHECKED BY:
<br />JPM
<br />DRAWN BY:
<br />PW
<br />PROTO:
<br />LBA
<br />PROTO CYCLE:
<br />051514
<br />DOCUMENT DATE:
<br />120415
<br />,�N. FtADEEp����,i
<br />".4 C-ip�. �� G EN
<br />N o 7 1 7 ' 9N
<br />O: ST E OF :4
<br />ORI
<br />Jul 11, 2016
<br />POWER
<br />PLAN
<br />DETAILS
<br />AND
<br />SCHEDULES
<br />SHEET:
<br />E2
<br />
|