7838 Gall Blvd (3) - Laserfiche WebLink

Browse Search

AD-1 DEMOLITION FLOOR PLAN GENERAL NOTES: A. DEMOLITION INCLUDES BUT IS NOT LIMITED TO ITEMS SHOWN DASHED. B. THE CONTRACTOR SHALL FIELD VERIFY THE EXTENT OF DEMOLITION. C. GENERAL CONTRACTOR TO VERIFY ALL CONDITIONS PRIOR TO DEMOLITION. DISCREPANCIES BETWEEN DESIGN AND EXISTING CONDITIONS SHALL BE BROUGHT TO THE ATTENTION OF THE ARCHITECT PRIOR TO PROCEEDING WITH WORK. D. CARE SHALL BE TAKEN DURING DEMOLITION SO AS TO NOT DAMAGE OR ALTER ANY EXISTING STRUCTURAL MEMBERS OTHER THAN THOSE DESCRIBED IN THESE DOCUMENTS. THE PUBLIX REPRESENTATIVE SHALL BE NOTIFIED IMMEDIATELY IF ANY DAMAGE OCCURS, OR IS DISCLOSED DURING DEMOLITION. CARE SHALL BE TAKEN TO INSURE SUPPORT IS PROVIDED WHEREVER DEMOLITION IS PERFORMED. E. SALVAGED MATERIAL OF VALUE IS PUBLIX OWNED, COORDINATE WITH PUBLIX REPRESENTATIVE. F. REFER TO ENGINEERING PLANS FOR EXTENT OF MECHANICAL, ELECTRICAL, PLUMBING & STRUCTURAL DEMOLITION. G. G.C. TO PROTECT SLAB FROM DAMAGE IN AREAS TO REMAIN. REFER TO SHEET S-1 FOR SLAB REMOVAL COORDINATION. H. ALL OBJECTS LOCATED IN PATH OF ENTRANCE VESTIBULE EMERGENCY BREAKAWAY DOORS, SHALL BE REMOVED BY STORE ASSOCIATE, TO ALLOW FOR ACCESS CLEARANCES. HISSYMBOLBYO DEMOLITION FLOOR PLAN KEY NOTES: TEFERENCE NOTE: ONLY NUMBERED KEYNOTES APPLY TO THIS STORE 1O EQUIPMENT TO BE RELOCATED. 2O REFER TO STRUCTURAL SHEETS FOR EXTENT OF SLAB DEMOLITION. O REMOVAL OF DIETITIANS OFFICE TO BE SEQUENCE AS CLOSE TO THE END OF THE REMODEL AS POSSIBLE. O PORTION OF EXISTING COOLER WALL TO BE REMOVED. MATCH ADJACENT EXISTING HEIGHT. O5 REMOVE HOOD, RELATED DUCTWORK AND OTHER COMPONENTS. 6O REMOVE END PANEL FROM EXIST GONDOLA BACK. O REMOVE PORTION OF WALL AS SHOWN. 8� REMOVE STEEL WHEELS FROM COMPACTOR. 9O REMOVE CONCRETE SLAB. REF STRUCTURAL FOR EXTENT OF WORK. 10 REMOVE STONE VENEER IN FRONT OF ATM AS NOTED. AD-2 DEMOLITION REFLECTED CEILING KEY NOTES: TEFERENCE HISSYMBOLBYO NOTE: ONLY NUMBERED KEYNOTES APPLY TO THIS STORE OREMOVE EXISTING LIGHTS, SPRINKLERS AND DIFFUSERS. REF: MECH, ELECTRICAL AND FIRE PROTECTION FOR ADDITIONAL INFORMATION. 2O REMOVE ACOUSTICAL CEILING TILE AND GRID AS INDICATED. 3O PATCH AND REPAIR CEILING AS NEEDED. 4O EXISTING LIGHT FIXTURE SHOWN FOR REFERENCE ONLY. O REMOVE PORTION OF CEILING SYSTEM IN PREPARATION OF NEW ROOM O REMOVE EXISTING GREASE HOOD. REF. MECHANICAL FOR MORE INFORMATION. EQ-1 EQUPIMENT PLAN GENERAL NOTES: A. EXIT PATH SHALL BE MAINTAINED TO EXIT DOORS CLEAR FLOOR SPACE. IN ADDITION, REAR CORRIDORS SHALL MAINTAIN A 44" WIDE EGRESS PATH. B. STOCK STACKING LIMITS SHALL BE OBSERVED. C. ELECTRICAL PANELS SHALL MAINTAIN A 30"W X 36"D X 78"H CLEAR FLOOR SPACE, AND ELECTRICAL ROOM SHALL BE FREE OF STORED ITEMS. D. FOR NEW MILLWORK, SEE SUP PLANS PROVIDED BY PUBLIX. E. PROVIDE METAL CLOSURE AT TOP, SIDES, AND BOTTOM OF CASES AS REQUIRED FOR THE FUNCTION OF R/A CIRCULATION AND/OR SEALING DAIRY COOLER OPENING, BY REFRIGERATION CONTRACTOR. F. CONTRACTOR SHALL VERIFY ALL EXISTING SITE CONDITIONS, DIMENSIONS AND ELEVATIONS IN THE FIELD AND REPORT ANY DISCREPANCIES AND/OR OMISSIONS WHICH WOULD INTERFERE WITH SATISFACTORY COMPLETION OF THE WORK. G. CONTRACTOR SHALL COORDINATE LOCATION OF ACCESSIBLE SIGNAGE, DISPENSERS, AND AMENITIES WITH PUBLIX REPRESENTATIVE IN THE FIELD. ITEMS NOT SHOWN ON THIS PLAN OR ADDED IN THE FIELD MUST COMPLY W/ FBC. H. PUBLIX TO PROVIDE SPLASHGUARD, IF NOT EXISTING, AT SIDE(S) OF HANDSINK WHERE HANDSINK IS WITHIN 12" OF SINK, FOOD PREP OR COOKING EQUIPMENT. I. ALL COUPON DISPLAYS SHALL BE MOUNTED BETWEEN 24" AFF AND 54" AFF AND WITHIN A 10" SIDE REACH. J. REMOVE ALL PLASTIC BAG DISPENSERS AND PAPER TOWEL DISPENSERS THAT ARE NOT LOCATED 48"H MAX AFF AND WITHIN 12" OF AISLE. REPLACE W/ NEW FLOOR MOUNTED ACCESSIBLE DISPENSER STAND. K. ALARM SYSTEM (BY OTHERS) SHALL HAVE AUDIOVISUAL SIGNAL ALARMS IN COMPLIANCE W/ FBC. EQUIPMENT PLAN KEY NOTES:REFERENCED BYTHIS SYMBOL D NOTE: ONLY NUMBERED KEYNOTES APPLY TO THIS STORE 11 NEW MILLWORK BY PUBLIX. REF SUP PLANS PROVIDED BY PUBLIX. 2] NEW CASE TRIM TO MATCH EXIST/ADJACENT CASE TRIM. 3❑ PATCH PASS THRU AS REQUIRE. ❑4 MAINTAIN 5'-0" CLEAR FLOOR SPACE IN FRONT OF ENTRANCE/EXIT VESTIBULE BREAKAWAY DOORS AS INDICATED. 5❑ NEW WALL. REF SHEET A-1 FOR ADDITIONAL INFORMATION. 6] NEW COUNTERTOP BY PUBLIX. 7❑ RESKIN COUNTERTOP. ❑RELOCATE COUPON DISPENSER TO A HEIGHT NO LESS THAN 24" AND NO GREATER THAN 48"H WITHIN 10" REACH. ❑9 NEW WEATHER SEAL STRIPS TO BE PUT ON BREAKAWAY DOORS. 10 MAINTAIN AISLES 36" MIN. CLEAR ACCESSIBLE PATH. 11 RELOCATED OR PROVIDED NEW, BY PUBLIX, OVERHEAD SIGN W/ INTERNATIONAL El WHEELCHAIR SYMBOL AND MESSAGE "POWERED SHOPPING CARTS," REF SIGN "P" 2/A-2. 12 PUBLIX TO PROVIDE OVERHEAD SIGN W/ INTERNATIONAL WHEELCHAIR SYMBOL AND MESSAGE "ASSISTANCE ID AVAILABLE UPON REQUEST," REF SIGN "N" 2/A-2. 13 NEW CHAIN LINK WITH LOCK. REF: DETAILS 17-20/A-18. GC TO PROVIDE THE NECESSARY STRUCTURAL ANCHORS AND SUPPORT FOR THE 14 OVERHEAD ELEMENT INCLUDING RESOLUTION OF ANY CONFLICTS WITH POTENTIAL OBSTRUCTION OR MECHANICAL DUCTS/ EQUIPMENT. RELOCATE PER PLAN OR AS NEW LINEUP REQUIRES. REPLACE POLES AS FIELD 15 DETERMINED TO BE DAMAGE. 16 NEW 60" TALL WING WALL. 17 NEW BOLLARDS, REF: DETAILS 5/A-2 FOR ADDITIONAL INFORMATION. 18 NEW POLYMER WHEELS FOR THE COMPACTOR. 19 NEW FALSE COLUMN. REF: REFRIGERATION. 20 NEW GATE BY PUBLIX. ©1 MAINTAIN T-0" IN FRONT OF ELECTRICAL PANELS. ©2 NEW FULL HEIGHT WALL. 23 NEW 8"X8" FALSE COLUMN. 24 REMOVE AND REPLACE SOFFIT AS REQUIRED TO REPLACE EQUIPMENT. a NEW 52" WALL. REF SHEET A-1 FOR ADDITIONAL INFORMATION. RELOCATE CUSTOMER USE BAGS AT OR BELOW A HEIGHT OF 48" AFF AND WITHIN 10" SIDE 26 REACH. ©7 RELOCATE CCTV EQUIPMENT PROTOTYPICALLY BACK TO SERVER RACK. 28 PUBLIX TO PROVIDE TACTILE BRILLE SIGN ON WALL OR DOOR. REF SHEET A-2. ADJUST DOOR CLOSER TO REQUIRE 5LBS OR LESS PUSH PULL FORCE AND A MINIMUM OF 5 SECONDS FOR THE DOOR TO CLOSE FROM 900 OPEN TO 120 FROM THE STRIKE. 30 INSULATE SUPPLY AND WASTE PIPES AT THE SINK. 31 REMOUNT TIME CLOCK AT NO GREATER THAN 48" A.F.F. A-1 FLOOR AND FINISH PLAN KEY NOTES: REFERENCED BYTHISSYMBOL NOTE: ONLY NUMBERED KEYNOTES APPLY TO THIS STORE D PATCH AND REPAIR FLOOR TO MATCH EXISTING FLOOR FINISH, AS NECESSARY. 2❑ REFER TO STRUCTURAL SHEET FOR EXTENT OF THE SLAB WORK. ❑ REFER DETAIL 24/A-18 FOR WALL SECTION. A-3 RELFECTED CEILING PLAN GENERAL NOTES: A. ALL NEW CEILINGS TO BE CLASS. B. REFER TO MECHANICAL AND ELECTRICAL DRAWINGS FOR ADDITIONAL INFORMATION. C. EXAMINE EXISTING REFRIGERATION CHASES FOR POSSIBLE REUSE. REBUILD ACCORDING TO DETAIL 10 OR 11/A-18 AS APPLICABLE. D. GC TO PROVIDE AND INSTALL TWO #10 SAFETY WIRES PER ALL NEW AND IMPROPERLY SUPPORTED EXISTING METAL HALIDE AND FLUORESCENT FIXTURES. ATTACH TO JOIST AT PROPER LOCATION AS COORDINATED WITH ELECTRICAL CONTRACTOR. (ELECTRICAL SHALL ATTACH TO FIXTURE). E. WHERE CEILING HEIGHTS CHANGE, PROVIDE A BULKHEAD AS REQUIRED. REF DETAIL 14/A-14. F. EXISTING DUCTWORK, DIFFUSERS, LIGHTS AND SPRINLER HEADS SHOWN FOR REFERENCE ONLY NOT INCLUDED IN SCOPE OF WORK. G. ALL LAY -IN CEILING MUST BE INSTALLED PER IBC LOCAL SEISMIC CATEGORY REQUIREMENTS. H. ALL FOOD PREPARATION AREAS GET IN VINYL FACED CEILING TILE. SEE PLAN A-2 ROOM FINISHES SCHEDULE. REFLECTED CEILING PLAN KEY NOTES:REFERENCED BY THIS SYMBOL p NOTE: ONLY NUMBERED KEYNOTES APPLY TO THIS STORE 1❑ INSTALL NEW PORTION OF CEILING SYSTEM AS INDICATED. 2❑ NEW GREASE HOOD. REF MECHANICAL FOR ADDITIONAL INFORMATION. D NEW TRACK LIGHTS. REF: ELECTRICAL FOR ADDITIONAL INFORMATION. 4❑ NEW DIFFUSER. REF: MECH FOR ADDITIONAL INFO. NEW OR RELOCATED FIRE SPRINKLER AS SHOWN. REF: FIRE PROTECTION FOR 5 ADDITIONAL INFORMATION. 6❑ NEW LIGHT FIXTURE. REFER TO ELECTRICAL DRAWINGS FOR MORE INFORMATION. 7❑ INSTALL NEW SOFFIT SYSTEM AS INDICATED. ❑ CLEAN ACOUST TILE. 9❑ CLEAN VINYL CEILING. 10 CLEAN INSULATED CEILING. 11 NEW GREASE HOOD. REF MECHANICAL FOR MORE INFORMATION. A-5 ROOF PLAN GENERAL NOTES: A. INFORMATION SHOWN IN HERE IS EXISTING UNLESS SPECIFICALLY NOTED OTHERWISE. FIELD VERIFY LOCATION OF ALL EXISTING COMPONENTS. B. COORDINATE WITH HVAC, PLUMBING, REFRIGERATION AND STRUCTURAL DRAWINGS FOR EXACT LOCATION OF EQUIPMENT. C. CONTRACTOR TO PATCH ROOFING SYSTEM AS NECESSARY TO MATCH EXISTING. REF: STRUCTURAL FOR ADDITIONAL INFORMATION. D. CONTRACTOR SHALL INSTALL CRICKETS TO DIVERT WATER AT NEW EQUIPMENT. ROOF PLAN KEY NOTES: REFERENCED # BY THIS SYMBOL NOTE: ONLY NUMBERED KEYNOTES APPLY TO THIS STORE 9❑ EXISTING CURB AND CRICKET. ❑PAINT EXISTING ROOF BENCH USING RUST RESISTANT PAINT. REF: STRUCTURAL SHEETS FOR ADDITIONAL INFORMATION. ❑ EXISTING EQUIPMENT TO BE REMOVED. ❑NEW FAN AND CURB. REF: MECH & STRUCTURAL FOR ADDITIONAL INFORMATION. N �00 00 u U 7� v 0 r-•+ w o w rn QN 0 N z W > W W U J LO � W v! O O U w 0 p a Lo a s � 0 o U) z h a OU o c c 0 3 U m g M N (:D s_ L0 M W N o < ~ of s �C O X o LL J� w m J zMQ� ULLI C� '' d LLI g a ti N 4� w Q LU dyo W J LL d' • •.G�y m 0 CV J N J m U) QU W � J w O o z M N U ado N w U � N w C) Z 0 ui O. 0 0 U 000 2019 Hawkins Construction, Inc