Laserfiche WebLink
C'4 <br />3g <br />< <br />Q0 <br />CD <br />-.1 <br />-0 <br />c:> <br />t2 <br />t2 <br />I <br />LO <br />t2 <br />I <br />PI) <br />C14 <br />4;;, <br />C�4 <br />C14 <br />1`10 <br />t2 <br />39 <br />C) <br />9 <br />C=) <br />PI) <br />t2 <br />1 <br />LO <br />t2 <br />I <br />U) <br />Cr <br />0 <br />C-1 <br />K) <br />c14 <br />E <br />co <br />w <br />E <br />0 <br />.2 <br />0 <br />0 <br />04 <br />C4 <br />C'� <br />CL <br />C=) <br />C4 <br />DO <br />U) <br />THESE DETAILS ARE GENERIC AND <br />MEANT TO SHOW GENERAL FLASHING <br />AND WATERPROOFING METHODS TO <br />BE USED. <br />3/8" CEMENT <br />PLASTER <br />12 MIL DRYLOK <br />CMU - MASONRY BLOCK <br />EXTREME <br />WINDOW <br />FASTENER <br />1) SEALANT AT <br />4) SEALANT JOINT <br />VvINDOWBUCKTO <br />OUTSIDE EDGE OF <br />MASONRY <br />WINDOW BUCK- <br />2) SEALANT JOINT <br />5) SEALANT FROM <br />INSIDE EDGE OF <br />WINDOW FRAME <br />WINDOWBUCK <br />ACROSS WINDOW BUCK <br />AND EXTEND TO <br />- WINDOW FRAME <br />MASONRY <br />ATTACHED <br />PER CODE <br />ED S LANT <br />6) TOOLED SEALANT <br />REQUIREMENTS <br />�IDGING <br />BEAD BRIDGING <br />NG AND VIANDOW <br />CLADDING AND WINDOW <br />FRAME <br />3) SEALANT WINDOW FRAME T( <br />WINDOW BUCK ALL THE WAY <br />AROUND, INCLUDING SILL. <br />SCS 06 05 CMU INSTALLATION 6 POINT BUCK AND <br />FENESTRATION INSTALLATION AND INTERFACE <br />JAMB, SILL AND HEAD DETAIL <br />APPROVED SHEATHING <br />APPROVED HOUSEWRAP <br />STRUCTAILATH TWIN TRACK 2.5 <br />3/4" CEMENT PLASTER <br />12 MIL (min) DRYLOK EXTREME <br />APPROVED FLASHING TAPE <br />'V'SEALANT SOCKET WITH <br />TOOLED APPROVED SEALANT <br />SCS 0602 WINDOW FIN INTERFACE WITH <br />EXTRUDED SHOULDER <br />WEATHER <br />RESISITIVE <br />BARRIER <br />HEAD FLASHING TIE-IN INSTRUXTI( <br />1. Cut, fold up & temporarily secure 1 <br />resistive barrier above header to allow for <br />flashing installation <br />2. Self -adhered flashing plus head flashing under <br />weather resistive barrier <br />3. Fold weather resistive barrier back over head <br />flashing and sea[ with tape <br />SELF -ADHERED FLASHING Scale: NTS <br />FLANGED WINDOW <br />FLASHING INSTALLATION AFTER WEATHER RESISTIVE BARRIER <br />EXTERIOR SHEATHING <br />REFER TO TECHNICAL <br />LETTER ON CHEMICAL <br />COMPATIBILITY <br />SELF -ADHERED FLASHING X <br />DO NOT FLASH OVER <br />BOTTOM NAILING <br />FLANGE <br />SELF -ADHERED FLASHING <br />HALF ROUND WINDOW <br />SELF -ADHERED FLASHING <br />PRODUCTS DETAILS <br />WATER RESISTIVE BARRIERS ARE REQUIRED BEHIND STUCCO <br />PER THE FBC RESIDENTIAL 7TH EDITION (2020) <br />Detail Instructions <br />Refer to the number marked as # in each detail that corresponds to the <br />numbered items in the list Rinstructions below: <br />1 . Install self -adhered flashing in order as shown by numbers <br />2. Install flashing and weather resistive barrier to form water shedding <br />laps <br />3. Self -adhered flashing can be substituted for building paper <br />4. Split the release paper using the ripcord (Split release on demand, <br />embedded in the adhesive layer) - for ease of installation and to <br />minimize scoring cuts <br />5. Remove all release paper per standard installation instructions and <br />dhere to substrate using a square piece of flashing material (6" x 6" <br />a <br />Minimum) <br />6. Fold as shown by arrows <br />7. Angle of corner may vary, adjust folding of the flashing accordingly to <br />fit tight to corner <br />8. Mechanically fasten as necessary <br />NAILING FLANGE <br />SELF -ADHERED FLASHING <br />DECK JOIST <br />2x FRAMEWALL <br />TILE FINISH- <br />1/2" DUROCK- <br />81, CMU <br />4" OR 8" CMU <br />(PER SEAT DEPTH) <br />FILL WITH GROUT - <br />SLOPED MUD BED - <br />SHOWER PAN <br />VINYL <br />WEATHER <br />/E BARRIER & <br />tARILY SECURE <br />WOOD FRAME CONSTR. <br />EXTERIOR SELF -ADHERED FLASHIN <br />SHEATHING BY LAPPING DOWN <br />OVER RIM JOIST AND UP <br />WALL BY 6 IN. <br />WEATHER <br />RESISITIVE <br />BARRIER <br />SEAL TOPS OF JOIr <br />UNDER DECKING <br />(SEE DETAIL WP07) <br />ED FLASHING <br />SELF -ADHERED FLASHING <br />WEATHER RESISTIVE <br />BARRIER <br />SELF -ADHERED FLASHING <br />EXTERIOR DOOR WITH DECK - SECTION A <br />EXTERIOR SHEATHING <br />3/4"-1 " BEAD OF CONSTR. <br />ADHESIVE TO BE APPLIED UNDER <br />THRESHOLD OF DOOR AND RETURN <br />Up JAMB 6". USE LIQUID NAIL BRAND <br />OR EQUAL WEATHER PROOF CAULKING <br />SECTION -A (SEE DETAIL <br />SELF -ADHERED FLASHING <br />SEAL TOPS OF JOISTS <br />UNDER DECKING <br />(SEE DETAIL WP07) <br />E <br />AM <br />SELF-ADHER <br />Q <br />V-4" PER PLAN <br />SHOWER SEAT <br />SELF -ADHERED FLASHING <br />EXTERIOR DOOR WITH DECK <br />SELF -ADHERED FLASHING <br />OUTSIDE CORNER <br />U <br />D <br />DOOR ROUGH OPENING <br />3/4"-1 "BEAD OF CONSTR. <br />ADHESIVE TO BE APPLIED UNDER <br />THRESHOLD OF DOOR AND <br />RETURN UP JAMB 6". USE LIQUID <br />NAIL BRAND OR EQUAL WEATHER <br />PROOF CAULKING <br />SELF -ADHERED FLASHING <br />SUBIFLOOR <br />RIM JOIST <br />INSTALL SELF -ADHERED <br />FLASHING JAMB & HEAD <br />FLASHING, SEE <br />FLANGED VIANDOW <br />(SEE DETAIL WP01) <br />SELF -ADHERED FLASHING, <br />EXTEND A MINIMUM 6" <br />VERTICALLY FROM <br />BOTTOM OF <br />THRESHOLD <br />�!e <br />:LF-ADHERED FLASHING <br />XCH <br />HERED FLASHING <br />2 <br />4 <br />5 <br />WINDOW UNIT <br />SLOPE <br />FLASHING REQUIREMENTS <br />0.3 in: 12.0 in R703.1 General. EAterior walls shall provide the building with a weather -resistant exterior wall envelope. The exterior wall envelope shall <br />(0.6 cm: 30.5 cm) include flashing as described in Section R703.4. <br />SELF -ADHERED FLASHING <br />R703.1.1 Water re4istance. The exterior wall envelope shall be designed and constructed in a manner that prevents the accumulation of <br />EXTERIOR <br />water within the wall assembly by providing a water-resistant barrier behind the exterior cladding as required by Section R703.2 and a means <br />CEMT. FIN. <br />of draining to the exterior water that penetrates the exterior cladding. <br />BUILDING PAPER <br />WIRE LATH R703.2 Water-resi4tive barrier. One layer of No. 15 asphalt felt, free from holes and breaks, complying with ASTM D226 for Type 1 felt or <br />other approved wAter-resistive barrier shall be applied over studs or sheathing of all exterior walls No. 15 asphalt felt shall be applied <br />horizontally, with the upper layer lapped over the lower layer not less than 2 inches. Where joints occur, felt shall be lapped not less than 6 <br />inches. Other approved materials shall be installed in accordance with the water -resistive barrier manufacturer's installation instructions. The <br />No. 15 asphalt felt or other approved water -resistive barrier material shall be continuous to the top of walls and terminated at penetrations and <br />building appendages in a manner to meet the requirements of the exterior wall envelope as described in Section R703. 1. <br />R703.7.3 Water -resistive barriers Water -resistive barriers shall be installed as required in Section R703.2 and, where applied over <br />Qwood -based sheathing, shall include a water -resistive vapor -permeable barrier with a performance at least equivalent to two layers of Grade <br />D paper. The individual layers shall be installed independently such that each layer provides a separate continuous plane and any flashing <br />(installed in accordance with Section R703.4) intended to drain to the water -resistive barrier is directed between the layers. <br />SELF -ADHERED FLASHING <br />CEMT. FINISH SILL] POTSHELF/ CHIMNEY SHOULDER Exception: Where the water -resistive barrier that is applied over wood -based sheathing has a water resistance <br />equal to or greater than that of 60-minute Grade D paper and is separated from the stucco by an intervening, <br />MECHANICALLY FASTEN IF RUBBERIZED ASPHALT substantially nonwater-absorbing layer or designed drainage space. <br />RUBBERIZED <br />NEEDED IN CORNERS ASPHALT ADHESIVE ADHESIVE <br />THROUGH SELF -ADHERED <br />R703.4 Flashing. Approved metal flashing, vinyl flashing, self -adhered membranes and mechanically attached flexible flashing shall be <br />FLASHING --q;=l P-ADHERED FLASHING <br />' <br />rew <br />SELF -ADHERED FLASHING <br />INSIDE CORNER <br />Ground <br />FOUNDATION WEEP SCREED <br />STRIP OF SAF <br />DRAINAGE PLANE WRB <br />BOND BREAK WRB <br />SF LATH <br />WRAP DIP WRB ONTO <br />THE VERTICAL <br />SURFACE TO TOP OF <br />FLANGE AS AN AIR <br />BARRIER <br />3-1/2" INCH FLANGE <br />THIS GAP IS A RESULT OF <br />PLASTER STOP NATURAL SHRINKAGE. <br />DO NOT SEAL. <br />CONTINUOUS BACKER <br />ROD & SEALANT <br />DRIP SCREED PLASTIC <br />ACCESSORY <br />SOFFIT/CANTI LEVER <br />applied shingle -fashion or in accordance with the manufacturer <br />s instructions. Metal flashing shall be corrosion resistant. Fluid -applied <br />membranes used as flashing shall be applied in accordance with the manufacturer's instructions. All flashing shall be applied in a manner to <br />SCORED prevent the entry of water into the wall cavity or penetration of water to the building structural framing components. <br />RELEASE PAPER <br />Self -adhered membranes used as flashing shall comply with AAMA 711. All exterior fenestration products shall be sealed at the juncture with <br />(BEFORE FOLDING, SCORE the building wall with a sealant complying with AAMA 800 or ASTM C920 Class 25 Grade NS or greater for proper joint expansion and <br />RELEASE PAPER TO EXPOSE <br />ADHESIVE AS SHOWN) <br />contraction, ASTMC 1281, AAMA 812, or other approved standard as appropriate for the type of sealant. Fluid -applied membranes used as <br />flashing in exterior walls shall comply with AAMA 714. The flashing shall extend to the surface of the exterior wall finish. Approved flashings <br />shall be installed at the following locations: <br />1. 1.Exterior window and door openings. Flashing at exterior window and door openings shall extend to the surface of the exterior wall <br />finish or to the water -resistive barrier complying with Section 703.2 for subsequent drainage. Mechanically attached flexible flashings <br />shall comply with AAMA 712. Flashing at exterior window and door openings shall be installed in accordance with one or more of the <br />2 following: <br />5 1.1 The fenestration manufacturer's installation and flashing instructions, or for applications not addressed in the fenestration <br />manufacturer's instructions, in accordance with the flashing manufacturer's instructions. Where flashing instructions or details <br />are not provided, pan flashing shall be installed at the sill of exterior window and door openings. Pan flashing shall be sealed or <br />sloped in such a manner as to direct water to the surface of the exterior wall finish or to the water resistive barrier for <br />7 subsequent drainage. Openings using pan flashing shall incorporate flashing or protection at the head and sides. <br />1.2 1.2. In accordance with the flashing design or method of a registered design professional. <br />1.3 1.3. In accordance with other approved methods. <br />of <br />1.4 In accordance with FMA/AAMA 100, FMA/ AAMA 200, FMA/WDMA 250, FMA/AAMA/ WDMA 300 or FMA/AAMA/WDMA 400. <br />2.2.At the intersection of chimneys or other masonry construction with frame or stucco walls, with projecting lips on both sides under <br />stucco copings. <br />3.3.Under and at the ends of masonry, wood or metal copings and sills. <br />4.4.Continuously above all projecting wood trim. <br />5.5.Where exterior porches, decks or stairs attach to a wall or floor assembly of wood -frame construction. <br />6.6.At wall and roof intersections. <br />Water Resistant Barrier 7.7.At built-in clutters. <br />Lath <br />Sheathing <br />Stucco <br />LEGEND <br />SELF ADHERED FLASHING (SAF) <br />DRAINAGE PLANE (DP) WEATHER RESISTANT <br />BARRIER (vVRB) <br />BOND BREAKWEATHER RESISTANT BARRIER - <br />SELF FURRING (SF) LATH <br />PLASTER ACCESSORY <br />SHEATHING, 'OSB', PLYWOOD, DENSGLASS- <br />Cement Plaster <br />in accordance <br />with ASTMC926 <br />over wood 2nd <br />floor <br />STRUCTURAL FRAMING <br />STRUCTURAL SHEATHING <br />STRIP OF SAF <br />DRAINAGE PLANE WRB <br />BOND BREAK WRB <br />SF LATH <br />THESE DETAILS ARE GENERIC AND MEANT TO SHOW GENERAL <br />FLASHING AND WATERPROOFING METHODS TO BE USED. <br />------ 1 <br />7/8" Cement Plaster <br />in accordance with <br />ASTMC926 <br />Felt backed metal <br />lathe in accordance <br />with ASTMC 1063 <br />Building Paper <br />7/16" O.S.B. <br />sheathing <br />Metal <br />Flashing <br />Weep Screed <br />Installed As Per <br />Manufact. Specs. <br />Maintain <br />Bottom of <br />Weep Screed <br />1 1/2" to 2" <br />Above Roof <br />Sheathing <br />V \Nl� I <br />Note: <br />The building paper and metal lath must be <br />Cement installed over the top of the weep screed. <br />Plaster <br />-A_CKE_R­_R0_D____4 over block <br />1 st floor <br />FINISH <br />WEEP SCREED DETAIL <br />SCALE: NOT TO SCALE <br />7/8" Cement Plaster <br />in accordance with <br />ASTMC926 <br />Felt backed metal <br />lathe in accordance <br />withASTMC1063 <br />Building Paper <br />7/16" 0. S. B. <br />sheathing <br />Starnpede or similar <br />cauk bottom <br />joint only <br />Weep Screed <br />Installed As Per <br />Manufact. Specs. <br />1/2" Cementitious <br />Decorative Finish <br />All inside and <br />outside corner will <br />need to be miter <br />cut and caulked all <br />butt joints need to <br />becaulked using <br />Stampede or sim. <br />caulk for all <br />, <br />40 �e <br />CL <br />ti. co <br />CD P, <br />00 C= <br />= 23 <br />do 4-4 <br />3g 0 <br />co is 1=0 <br />13 at <br />1=0 E <br />W C3. <br />9-' <br />cx <br />C14 <br />C� <br />CN <br />'Ir <br />E�l <br />LE VV�, <br />0 <br />GEN 61 <br />co <br />0 X! <br />No PE7' 50 <br />�7 <br />��5 <br />STATE OF iv;: <br />441 <br />A' !�- ft <br />k <br />% <br />0 ir\' <br />To the best of the Engineees knowledge, information and belief, <br />the structural plans and specifications contained within these <br />drawings comply with the 2020 Florida Building Code - <br />Residential 7th Edition. Engineer's signature and seal is only for <br />the structural engineering portions of the drawing pages bearing <br />Engineers signature and seal, <br />0 <br />I E 8 c,4 <br />- 8 g �; o <br />R c� <br />0 6 <br />(0 <br />0 - N u- <br />a 501 "o- -� V <br />N 0 a. uj <br />I&L <br />05;f <br />_j <br />0. <br />Z <br />.q .0� 0 <br />e �; 0 <br />'D Lu 9 <br />o) < <br />W r Z <br />co -1 6 0 LU <br />c4 Z 0 <br />IL <br />< <br />Z <br />W <br />(D <br />a) <br />< <br />co <br />Lf) <br />(D <br />4--J <br />FJ <br />0 Lu <br />V) <br />V) <br />Lu <br />I E <br />2 8 <br />6 <br />d <br />c=, <br />cl> <br />cl� <br />29 <br />z <br />z <br />< <br />__j <br />U_ <br />E <br />o <br />M <br />4 <br />0 <br />E y <br />CL <br />. <br />mo <br />T, . <br />w, <br />oo <br />" <br />E <br />Yo <br />1< <br />Z <br />z. <br />w <br />o <br />o <br />z <br />Z <br />E5 <br />o� <br />�z <br />15 <br />o <br />o <br />�z <br />W <br />1§ <br />c> <br />M <br />2'. <br />I <br />ow <br />3t <br />ZS <br />w <br />o <br />.077 <br />E <br />00 <br />7 <br />C*4 <br />M <br />C.0 <br />cr) <br />Co <br />C) <br />U) <br />C:) <br />50 <br />.2 <br />CD <br />0 <br />L0 <br />ce) <br />L0 <br />c) <br />LO <br />4i <br />E <br />1 C14 <br />0 <br />0 <br />Z <br />cc <br />Z <br />:3 <br />u) 7- <br />E C) <br />- <br />cc <br />r_ <br />ig <br />(1 <br />E 4.; <br />0 0 M <br />0 _J 0 <br />4) <br />_J <br />JOB <br />NO 23-13125-13130 <br />SCALE AS NOTED <br />SHEET NO. <br />WP <br />