7954 Sail Clover Ln - Laserfiche WebLink

Browse Search

x © l z`fJ�¢ w cn¢owo-c�c.� r- 0- r„ p :z Q�C)Z3Mp p Ld a_ OUT TO BZ-50 POWER PACKS FROM RELAY MODULE PHAROS LIGHTING 8 CONTROL SYSTEM (16" 00") LEVITON ENCLOSURE 47605-28N 14 4.2 10 AC Mains M1 M1 TRINITY - INTELLIGENT POWER SUPPLY MAX 5 PER 120VAC 20A CIRCUIT 12 Channel - 700mA 4.1 SWITCH EON POWER SUPPLY MAX 4 PER 20 A CIRCUIT NOTES: (ALL FIXTURES TO BE WIRED IN SERIES) AC LINE VOLTAGE = 115-277 VAC - FREQUENCY = 50-6OHz - CONNECT TO 15A OR 20A BRANCH CIRCUIT. Q DEDICATED 120VAC - 20A QUAD OUTLET. F3 CLASS 2 OUTPUT POWER SUPPLY CONTAINS DIGITAL POWER CONVERSION, PULSE DIMMING, CURRENT DRIVERS & SURGE PROTECTION. PERMANENTLY INSTALLED IN DRY LOCATIONS ONLY W/ AMBIENT TEMP. RANGE OF -47 TO 104-F (-20°C TO 40°C) RATED INPUT VOLTAGE = 2.7 A @ 115 VAC, 1.1 A ® 240 VAC & 1 A 0 277 VAC. 4.1 700mA TRINITY W/ 12 ADDRESSABLE CONSTANT CURRENT CHANNELS, VARIABLE VOLTAGE FROM 6-27 VOLTS DC VOLTS PER CHANNEL OUTPUT POWER = 27 VOLTS/CHANNEL x 12 CHANNELS x .7A = 226W MAX. 4.2 SWITCH TO EON POWER SUPPLY 4.3 2100 mA EON W/ 4 CHANNELS, VARIABLE VOLTAGE FROM 20-43.8 VOLTS DC PER CHANNEL. OUTPUT POWER = 43.8 VOLTS/CHANNEL x 4 CHANNELS x 2.1 A = 368W MAX. 15 OUTPUT TRINITY CABLE = SHIELDED 22/6 AWG TWISTED PAIR (WHITE/BLACK, RED/BLACK & GREEN/BLACK) NOTE: BLACK IS ALWAYS NEGATIVE. ® SHIELDED 18/2 AWG MULTI -CONDUCTOR 7.1 570-630 LUMEN (45W EQUIV.) RECESSED DOWNLIGHT - MUST BE WIRED IN SERIES - EACH FIXTURE CONSUMES 11.7 VOLTS OR 8.2 WATTS (INPUT LOAD = 10.1 WATTS) 7.2 790-860 LUMEN (60W EQUIV.) RECESSED DOWNL.IGHT -- MUST BE WIRED IN SERIES - EACH FIXTURE CONSUMES 12.5 VOLTS OR 12.5 WATTS (INPUT LOAD = 15.1 WATTS) 7.3 1250 LUMEN (80W EQUIV.) LIGHT - SINGLE FIXTURE PER CHANNEL - EACH FIXTURE CONSUMES 21 VOLTS OR 14 WATTS (INPUT LOAD = 17.5 WATTS) 7.4 2,000 LUMEN LINEAR LIGHT - TWO FIXTURES PER CHANNEL - MUST BE WIRED IN SERIES. M8 INPUT FROM OCCUPANCY SENSORS AND SWITCHES. WIRE REQUIREMENTS VARY BASED ON DEVICE. SEE SHEET E1.1 D FOR MORE DETAILS. ® DMX TERMINATION PLUG - INCLUDED. 10 CAT5e FROM CONTROL CABINET TO VARIOUS DEVICES. SEE SHEET 1.1D FOR DETAILS ON WHERE TO LAND THESE CABLES WITHIN THE CONTROL CABINET. 11 CONTROL OF LINE VOLTAGE DEVICES VIA POWER PACKS, TRIGGERED BY A RELAY MODULE IN THE CONTROL CABINET. RUN 18/2 WIRING .FROM CONTROL CABINET TO EACH POWER PACK. SEE DETAIL C3 ON SHEET 1.1D. 12 BLANK 13 BLANK 14 SURGE PROTECTED OUTLET(S) SUPPLIED BY LUMASTREAM. CONTRACTOR TO PROVIDE 120V AC POWER TO THE OUTLETS. u Comment to conformance of the lighting system in regard to NEC 2008 Article 411: With reference to NEC Article 411, "the lighting system is an assembly of listed parts operating at 30 VDC or less ... '° The power supply is UL listed under UL8750 (LED equipment for Use in Lighting Products) with Class 2 outputs for end use in lighting systems under UL2108 (Low -Voltage Lighting Systems). The UL file number for the power source is E330722. 411.3 Listing Required. Lighting systems operating at 30 volts or less shall comply with 411.3(A) or 411.3(B). 411.3(B) Assembly of Listed Parts. A lighting system assembled from the following listed parts shall be permitted: (1) Low -voltage luminaires TUV certified to UL 1598 for class 2 installations (2) Low -voltage luminaire power supply Power source is rated for 27 UDC max (3) Class 2 power supply All outputs are in accordance with UL1310 Standard for Class 2 Power Units (4) Low -voltage luminaire fittings Recessed housings are TUV certified to UL 1598 (5) Cord (secondary circuit) for which the luminaires and power supply are listed for use Output cords from listed power source is type CL3 or CMP UL listed file no: Ell 1 272-A (6) Cable, conductors in conduit, or other fixed wiring method for the secondary circuit Honeywell cable ETL listed with no exposed bare conductors . The luminaires, power supply, and luminaire fittings (including the exposed bare conductors) of an exposed bare conductor lighting system shall be listed for use as part of the same identified lighting system. And, 411.4 Specific Location Requirements. (A) Walls, Floors, and Ceilings. Conductors concealed or extended through a wall, floor, or ceiling shall be in accordance with (1) or (2): (1) Installed using any of the wiring methods specified in Chapter 3 (2) Installed using wiring supplied by a listed Class 2 power source and installed in accordance with 725.130 Installation will be in accordance with NEC 725,130 (B) Class 2 wiring methods ,.. 6 6 7.1 7.2 7.3 _/LED, `xiw_ AM= ///LED��` ''/�fLLDv� -� LLI F�\` i / �Lr-U� \ / �Lcu` \ / �Ltu` \ UP TO 2 FIXTURES PER CHANNEL TO BE WIRED IN SERIES XXLED % /LCLU\ \ LED`\`` I And, 411.5 Secondary Circuits. (A) Grounding. Secondary circuits shall not be grounded. Secondary circuits are not grounded (B) Isolation. The secondary circuit shall be insulated from the branch circuit by an isolating transformer. Power source is electrically isolated (C) Bare Conductors. Exposed bare conductors and current -carrying parts shall be permitted for indoor installations only. Bare conductors shall not be installed less than 2.1 m (7 ft) above the finished floor, unless specifically listed for a lower installation height. No bare conductors are used in the installation (D) Insulated Conductors. Exposed insulated secondary circuit conductors shall be of the type, and installed as, described in (1), (2), or (3): (1) Class 2 cable supplied by a Class 2 power source and installed in accordance with Parts I and III of Article 725. Insulated conductors installed in accordance with Part III of Article 725 (2) Conductors, cord, or cable of the listed system and installed not less than 2.1 rn (7 ft) above the finished floor unless the system is specifically listed for a lower installation height. (3) Wiring methods described in Chapter 3 And, 411.6 Branch Circuit. Lighting systems operating at 30 volts or less shall be supplied from a maximum 20-ampere branch circuit. The 27 VDC max. class 2 power supply is rated for 20 amps. REQUIREMENTS: 1) INSTALLATION SHALL BE IN ACCORDANCE W/ LOCAL, STATE, PROVINCIAL, COUNTY & NEC REGULATIONS. 2) THIS DOCUMENT IS FOR REFERENCE ONLY, USE IN CONJUNCTION WITH COMPONENT INSTALLATION INSTRUCTIONS. 3) CONDUIT REQUIRED FOR LIFE SAFETY LIGHTING. 4) CHECK LOCAL JURISDICTION FOR THE REQUIRED USE OF CONDUIT ON SYSTEMS HIGHER THAN 24 VOLTS. 5) SPECIFICATIONS SUBJECT TO CHANGE W/O PRIOR NOTICE. EMERALD ENGINEERING INC. 9942 CURRIE DAVIS DR. STE H., TAMPA, FL 33619 TEL (813) 995-0300 FLORIDA EB# 0027845 WWW.EMERALDMEP.COM EEI PROJECT# 180822 'vy y , a o L0 6 0 <,PLORS � A� ON A\� �a®�N `7�74d9flF`se®� ADAM T. POWELL, PE FL. REG. NO. PE73853 07 z 0 w cc m cc N Cz W 0 cc-0 CZ LM '^ vJ �L cli CL 4) Q Q N N N BSB DESIGN www.bsbd6sign.com 100 Main St. Suite 209 Safety Harbor, Florida 34695 8132654808 JOB NO: AM180320.00 PROJ MGR: AP DRAWN: DS CHECKED: AP TYPICAL RISER DIAGRAM & LOW -VOLTAGE CODE �, r TYPICAL RISER DIAGRAM T SCALE: N.T.S. LS-0.1 LS-0. 1