Laserfiche WebLink
T.O.M. <br />O <br />T.O.M. — — —� <br />HDR. ---- <br />0 <br />aoC) <br />Co <br />2nd F.FL. <br />CLG. HGT. <br />T.O.M. --- <br />AT GAR. <br />rng­ <br />8" FRIEZE — <br />BAND <br />oo <br />bo <br />_o <br />F.FL. _ — <br />S������� <br />SHINGLES <br />12 <br />__74.0 <br />----------------------------------------------------------------------------------- <br />TEXTURED <br />13 SH FINISH 13 SH <br />---------- HDR. <br />TEXTURED <br />FINISH <br />O <br />00 <br />35 SH 25 SH 25 SH <br />LEFT ELEVATION - STANDARD (STD <br />SCALE: 3/16" = V-0" <br />SHINGLES <br />— — — — — — — — — — — — — — - <br />TEXTURED <br />13 SH FINISH 13 SH <br />�— — — T.O.M. <br />---- HDR. <br />0 <br />o ao <br />— — — — _ 2nd F.FL. <br />— — — — _ CLG. HGT. <br />T.O.M. <br />AT GAR. <br />8" FRIEZE <br />BAND <br />ip 0) <br />00 <br />_o <br />F.FL. <br />-------L-----=16"BAND---------------------------------------------------------— — — — — — — — - <br />- — — — — — — — — <br />— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — <br />HDR. <br />-------------------- -- <br />co <br />_ <br />p <br />TEXTURED <br />'- <br />10 <br />o <br />FINISH <br />60 <br />0 <br />25 SH 25 SH 35 SH <br />RIGHT ELEVATION - STANDARD (STD <br />SCALE: 3/16" = 1'-0" <br />T.O.M <br />it <br />General Notes <br />ROOF CRITERIA: <br />• 12" OVERHANG U.N.O. <br />• PLUMB CUT FASCIA ROOF <br />• PITCH PER ELEVATION <br />**G.C. VERIFY ROOF PITCH** <br />ROOF PITCH VARIES PER SUBDIVISIONS IT IS THE <br />CONTRACTORS RESPONSIBILITY TO VERIFY <br />ROOF SLOPE REQUIREMENTS WITH TRUSS <br />MANUFACTURER. <br />**ELECTRICAL SPECIFICATION NOTES** <br />ELECTRICAL CONTRACTOR MUST VERIFY WITH <br />THE SPECIFICATIONS FOR THE TYPE OF FIXTURE <br />TO BE USED. LIGHT FIXTURES SHOWN ARE FOR <br />LOCATION PURPOSES. <br />r uovering <br />R703.7 Exterior Plaster. <br />Installation of these materials shall be in compliance with ASTM <br />C926 and ASTM C1063, or ASTM C1787 and the provisions of <br />this code. <br />R703.7.1 Lath. <br />Lath and Lath attachments shall be of corrosion -resistant <br />materials. Expanded metal or woven wire lath shall be attached <br />with 1-1/2" long, 11 gage nails having a 7/16" head, or 1-1/2" long, <br />16 gage staples, spaced in accordance with ASTM C1063 or <br />C1787, or as otherwise approved. (Refer to sheet SN1 for the <br />engineered method for Lath attachment.) <br />Lathing Accessories <br />Attachments shall be of corrosion -resistant materials. <br />Wood Application: 16 Ga.x1-1/2" long (3/4"-1" crown) staples @ <br />6" O.C. vertically/horizontally into the framing members. <br />Masonry Application: Concrete stub nail, 3/8" (10 mm) head dia. <br />min. @ 6" O.C. vertically/horizontally or compatible adhesives, <br />exterior gun -grade, construction adhesive with 1" dabs @ 6" O.C. <br />or in a semi -continuous bead between the solid plaster base and <br />the solid portion of the key attachment flange. <br />Control Joints: Install control joint lathing accessories in <br />conformance with C1063. Lath shall not be continuous through <br />control joints, but shall be stopped and tied at each side. <br />All accessories shall be in accordance with the latest ASTM <br />C1063 & ASTM C1861. <br />R703.7.2 Plaster. <br />Plastering with cement plaster shall be not less than three coats <br />where applied over any type of code -approved lath and shall be <br />not less than two coats where directly applied over masonry, <br />concrete, clay brick, stone, or tile. If the plaster surface is <br />completely covered by veneer or other facing material or is <br />completely concealed, plaster application need be only two coats, <br />provided total thickness is as set in Table R702.1(1). <br />Cement plaster shall be in accordance with ASTM C926 and <br />material shall be in accordance with one of the types listed in <br />R703.7.2. <br />R703.7.3 Water -Resistive Barriers. <br />Water -resistive barriers shall be installed as required in Section <br />R703.2 and, where applied over wood -based sheathing, shall <br />include a water -resistive vapor -permeable barrier with a <br />performance at least equivalent to two layers of Grade D paper. <br />The individual layers shall be installed independently such that <br />each layer provides a separate continuous plane and any flashing <br />(installed in accordance with Section R703.4) intended to drain to <br />the water -resistive barrier is directed between the layers. <br />R703.2 Water -Resistive Barrier. <br />One layer of No. 15 asphalt felt, free from holes and breaks, <br />complying with ASTM D226 for Type 1 felt or other approved <br />water -resistive barrier shall be applied over studs or sheathing of <br />all exterior walls. No. 15 asphalt felt shall be applied horizontally, <br />with the upper layer lapped over the lower layer not less than 2 <br />inches. Where joints occur, felt shall be lapped not less than 6 <br />inches. Other approved materials shall be installed in accordance <br />with the water -resistive barrier manufacturer's installation <br />instructions. The No. 15 asphalt felt or other approved <br />water -resistive barrier material shall be continuous to the top of <br />walls and terminated at penetrations and building appendages in <br />a manner to meet the requirements of the exterior wall envelope <br />as described in Section R703.1. <br />R703.4 Flashing. <br />Approved metal flashing, vinyl flashing, self -adhered membranes <br />and mechanically attached flexible flashing shall be applied <br />shingle -fashion or in accordance with the manufacturer's <br />instructions. Metal flashing shall be corrosion resistant. <br />Fluid -applied membranes used as flashing shall be applied in <br />accordance with the manufacturer's instructions. All flashing shall <br />be applied in a manner to prevent the entry of water into the wall <br />cavity or penetration of water to the building structural framing <br />components. <br />Self -adhered membranes used as flashing shall comply with <br />AAMA 711. All exterior fenestration products shall be sealed at <br />the juncture with the building wall with a sealant complying with <br />AAMA 800 or ASTM C920 Class 25 Grade NS or greater for <br />proper joint expansion and contraction, ASTM C1281, AAMA 812, <br />or other approved standard as appropriate for the type of sealant. <br />Fluid -applied membranes used as flashing in exterior walls shall <br />comply with AAMA 714. The flashing shall extend to the surface <br />of the exterior wall finish. <br />Approved flashings shall be installed at the following locations. <br />• Exterior window/door openings. <br />• Intersection of chimneys or other masonry construction with <br />frame walls. <br />• Under and at the ends of masonry, wood or metal copings <br />and sills. <br />• Continuously above all projecting wood trim. <br />• Where exterior porches, decks or stairs attach to a wall or <br />floor assembly of wood -frame construction. <br />• At wall and roof intersection. <br />• At Built-in gutters. <br />Coastal Flashings <br />All flashing material for coastal locations (ex: within 3,000 feet of the <br />ocean) shall be corrosion resistant material (ex: zinc and/or stainless <br />steel) and shall be selected for compatibility with adjacent wood <br />preservatives per the manufacturer's recommendations. <br />REV. 09,24.21 <br />r(h <br />+O o <br />N r, <br />C=' <br />v o <br />Q <br />+d+ N <br />0 <br />L <br />m �o <br />N a- <br />� E <br />A p <br />a � <br />w <br />M <br />O <br />N <br />v <br />N <br />0 <br />LE V',r <br />% <br />��,'. <br />GO•'���G•E•NSF. <br />• No PE787 ' <br />.tit • <br />;.� STATE OF • <br />/i. 1 <br />I`J <br />To the best of the Engineers knowledge, information and belief, <br />the structural plans and specifications contained within these <br />drawings comply with the 2020 Florida Building Code - <br />Residential 7th Edition. Engineer's signature and seal is only for <br />the structural engineering portions of the drawing pages bearing <br />Engineers signature and seal. <br />W v E <br />O N 8 <br />J <br />Loa <br />0 5 U) LL LL <br />0 <br />0 �04 0 , 0.d <br />Q <br />LL ii a y <br />J Z <br />ci _ Z <br />Z •�°' 0o <br />L (6 <br />O <br />�. 7'c N O m W Q <br />J <br />Z N MZ U F <br />Z O U ❑0❑ <br />Z <br />W <br />z N M <br />— O <br />00 <br />z OD <br />z I? <br />v <br />J — <br />N <br />N z <br />LL <br />LU <br />w <br />a <br />O w s <br />N Ly N <br />�c/1 U) <br />u, <br />J <br />E <br />L <br />airU <br />f <br />z I <br />c <br />._ U (D <br />0 <br />� <br />N d <br />e <br />�Q <br />sd <br />o <br />Z <br />w <br />M <br />J <br />0 <br />o <br />� <br />Z <br />LL <br />o <br />Zo <br />> ry <br />Zo <br />Z® <br />a <br />� CJ <br />og <br />f— ffl <br />_ <br />p <br />g0 <br />¢ <br />00 <br />o <br />0 < <br />Z <br />CO L <br />0 <br />0 <br />a Z <br />W <br />C <br /><z <br />6 <br />.0 <br />Z <br />�z <br />Z <br />QJ <br />m v <br />5 J <br />tim <br />a " <br />aw <br />Z <br />Z <br />az <br />f� <br />�� <br />LL <br />W <br />m <br />�� <br />�E <br />�- <br />X <br />o <br />w <br />`< <br />X0r <br />i0 <br />v <br />$ <br />z l< <br />c <br />o T <br />> W <br />c� <br />Cfl <br />T <br />N <br />M <br />L <br />CO <br />LID <br />r <br />r <br />T <br />00 <br />r— <br />v) m <br />r <br />CN <br />O <br />L) <br />� T o <br />O <br />CV <br />O <br />c6 <br />O <br />o <br />Z <br />M <br />Z <br />7 N <br />E O 0 T7 <br />M <br />a <br />E <br />0 16 <br />0 � Q p <br />3 <br />JOB <br />NO :23-13131-13136 <br />SCALE : AS NOTED <br />SHEET NO. <br />7.2 <br />