38444 5th Ave - Laserfiche WebLink

Browse Search

POWER NOTES O 1 I I 4. N3 1. PROVIDE TX TX 3/4" FIRE RETARDANT PAINTED PLYWOOD TELEPHONE BACKBOARD WITH TOP AT T AFF. EXTEND #6 CU FROM BACKBOARD TO GROUNDING ELECTRODE SYSTEM. EXTEND 1"C WITH PULLWIRE TO EXISTING TEL. SVC PNL LOCATED IN RM 120. 2. PROVIDE WIREMOLD SERIES ALA4800 TWO CHANNEL SATIN ANODIZED AL WIREWAY WITH OUTLETS 18 ON CENTER (TOP CHANNEL MOUNT). LOWER CHANNEL FOR DATA CABLES. 3. ENTIRE CIRCUIT TO BE ON GFCI BREAKER. 4. PROVIDE JUNCTION BOX WITH 120V CIRCUIT AS INDICATED ABOVE DOOR. GENERAL NOTES 1. THE ELECTRICAL INSTALLATION SHALL COMPLY WITH THE REQUIREMENTS OF THE 2008 NATIONAL ELECTRICAL CODE. 2. ALL GROUNDING ELECTRODE SYSTEMS SHALL BE INTERCONNECTED PER NEC 250.52. 3. ALL 120V CIRCUIT LENGTHS GREATER THAN 100 FT SHALL BE INCREASED TO #10 AWG AND TO # 8 AWG WHEN GREATER THAN 160 FT. INCREASE CONDUIT SIZE FOR 40% FILL. 4. REFER TO HVAC WIRING SCHEDULE FOR CIRCUITING REQUIREMENTS OF SAME. 5. WORKING CLEARANCE SHALL BE AFFORDED TO ALL ELECTRICAL EQUIPMENT IN ACCORDANCE WITH NEC 110.26. 6. ALL 15 & 20A,120V RECEPTACLES WITHIN 6FT OF A SINK SHALL BE GFCI PROTECTED. 7. WHERE A SHARED NEUTRAL CONDUCTOR IS USED FOR MULTIPLE BRANCH CIRCUITS, CONTRACTOR SHALL GROUP CIRCUITS TOGETHER IN PANEL AND PROVIDE A MANUFACTURER FURNISHED HANDLE -TIE TO SIMULTANEOUSLY TRIP ALL OF THE CIRCUITS SHARING THE NEUTRAL. 8. WHERE COMMUNICATIONS OUTLETS ARE SHOWN ADJACENT TO POWER RECEPTACLES, BOTH SHALL BE INSTALLED AT THE SAME ELEVATION. 9. VOLTAGE DROP IN ACCORDANCE WITH FLORIDA ENERGY CONSERVATION CODE 505.7.3 HAS BEEN TAKEN INTO ACCOUNT FOR THIS PROJECT. HVAC & PLUMBING EQ. WIRING SCHEDULE UNIT NUMBER MCA MOCP DISCONNECT BRANCH CIRCUIT SWITCH FUSES CONDUIT WIRE PANEL AHU-1 50 50 N1/60/2/240V -- 1" 2 #6 & 1 #10 EG L-61,63 AHU-2 45 45 N1/60/2/240V -- V 2 #6 & 1410 EG L-65,67 AHU-3 45 45 N1/60/2/240V -- 1" 2 #6 & 1 #10 EG L-69,71 AHU-4 48 50 N1/60/2/240V -- 1" 2 #6 & 1 #10 EG L-73,75 CU-1 35 60 N3R/60/2/240V -- 3/4" 2 #8 & 1 #10 EG L-64,66 CU-2 20 35 N3R/60/2/240V -- 1/2" 2 #12 & 1 #10 EG L-68,70 CU-3 20 35 N3R/60/2/240V — 1/2" 2 #12 & 1 #10 EG L-72,74 CU-4 28 50 N3R/60/2/240V -- 3/4" 2 #10 & 1 #10 EG L-76,78 EWH 12.5 20 NI/30/2/240 -- 3/4" 2 #10 & 1 #10 EG L-77,79 TEF-1 WTFH FAN -- 1/2" 2 #12 & 1 #12 EG WITH LIGHTS TEF-2 WITH FAN -- 1/2" 2 #12 & 1 #12 EG WITH LIGHTS System No. W-L-1049 F Ratings -1 and 2 Hr (See Item 1) T Rating -0 Hr L Rating At Ambient -Less Than 1 CFM/sq ft L Rating At 400 F -Less Than 1 CFM/sq ft Section A -A Wall Assembly -The 1 or 2 hr fire -rated gypsum wallboard/stud wall assembly shall be constructed of the materials and in the manner described in the individual U300 or U400 Series Wall or Partition Design in the UL Fire Resistance Directory and shall include the following construction features: A. Studs -Wall framing may consist of either wood studs or steel channel studs. Wood studs to consist of nom 2 by 4 in. (51 by 102 mm) lumber spaced 16 in. (406 mm) OC. Steel studs to be min 3-5/8 3-1/2 in. (89 mm) wide and spaced max 24 in. (610 mm) OC. When steel studs are used and the diam of opening exceeds the width of stud cavity, the opening shall be framed on all sides using lengths of steel stud installed between the vertical studs and screw -attached to the steel studs at each end. The framed opening in the wall shall be 4 to 6 in. (102 to 152 mm) wider and 4 to 6 in. (102 to 152 mm) higher than the diam of the penetrating item such that, when the penetrating item is installed in the opening, a 2 to 3 in. (51 to 76 mm) clearance is present between the penetrating item and the framing on all four sides. B. Gypsum Board* -5/8 in. (16 mm) thick, 4 ft (1.22 m) wide with square or tapered edges. The gypsum board type, thickness, number of layers, fastener type and sheet orientation shall be as specified in the individual U300 or U400 Series Design in the UL Fire Resistance Directory. Max diam of opening is 26 in. (660 mm) for steel stud walls. Max diam of opening is 14-1/2 in. (368 mm) for wood stud walls. The hourly F Rating of the firestop system is equal to the hourly fire rating of the wall assembly in which it is installed. 1A. Metallic Sleeve -(Optional, Not Shown) - Cylindrical sleeve fabricated from min 0.016 in. (0.41 mm) to max 0.105 in. (2.7 mm) thick sheet steel. Length of steel sleeve to be equal to the thickness of wall. Longitudinal seam of sleeve welded or overlapped min 1 in. (25 mm). The ends of the steel sleeve shall be flush or recessed max 1/4 in. (6 mm) from wall surfaces. 2. Through Penetrant -One metallic pipe, conduit or tubing to be installed either concentrically or eccentrically within the firestop system. Pipe, conduit or tubing may be installed at an angle not greater than 45 degrees from perpendicular. The annular space between pipe, conduit or tubing and periphery of opening shall be min 0 in. (0 mm, point contact) to max 2 in. (51 mm). Pipe, conduit or tubing to be rigidly supported on both sides of wall assembly. The following types and sizes of metallic pipes, conduits or tubing may be used: A. Steel Pipe -Nora 24 in. (610 mm) diam (or smaller) Schedule 10 (or heavier) steel pipe. B. Iron Pipe -Nora 24 in. (610 mm) diam (or smaller) cast or ductile iron pipe. C. Conduit -Nora 4 in. (102 mm) diam (or smaller) steel electrical metallic tubing, nom 6 in. (152 mm) diam (or smaller) steel conduit or nom 1 in. (25 mm) diam (or smaller) flexible steel conduit. D. Copper Tubing -Nom 6 in. (152 mm) diam (or smaller) Type L (or heavier) copper tubing. E. Copper Pipe -Nom 6 in. (152 mm) diam (or smaller) Regular (or heavier) copper pipe. 3. Fill, Void or Cavity Material* -Sealant -Min 518 in. (16 mm) thickness of fill material applied within annulus, flush with both surfaces of wall. At the point contact location between through penetrant and gypsum board, a min 3/8 in. (10 mm) diam bead of fill material shall be applied at the gypsum board/through penetrant interface on both surfaces of wall. SPECIFIED TECHNOLOGIES INC -SpecSeal Series SSS Sealant or SpecSeal LCI Sealant *Bearing the UL Classification Mark led 1Ck Architecture, Inc. WIEDRICK ARCHITECTURE INC. AA26001799 2020 HEIDELBERG AVE. DUNEDIN, FLORIDA, 34698 STATE OF FLORIDA PROFESSIONAL ENGINEER: MATTHEW OTTO PE 58722 L\ c-i cm r r� V m w w H � � v w � � o0 �J F" "' Ln o N � w M o w Ln 0 z 00 M a, N N VV `eq�``�y,�p� ,,...•v.V, U� jttp'��s� e No.58722 STATE OF '•�� .,S N Z `e a.i Q LO 00 M N Ln co C`7 J LL U) ---! J_ LLI N PROJECT ADDRESS: 38444 5TH AVE. ZEPHYRHILLS, FL 33542 CLIENT: FLORIDA PHARMACY SOLUTIONS, INC. 13933 17TH ST. SUITE 300 DADE CITY, FL 33525 EM DATE I DESCRIPTION I POWER PLAN Specified Technologies Inc. 210 Evans Way Somerville, NJ 08876 Reproduced courtesy of Underwriters Laboratories, Inc. &W-L-1 1 1 Created or Revised: December 14,20101 1 049 (800)992-1180 • (908)526-8000 • FAX (908)231-8415 • E-Mail:techserv@stifirestop.com • Website:www.stifirestop.com PAGE 1 OF 1 POWER FLAN 3/1(0"=1'-011 MDO PROJECT #: 14-87 E201 10/15/14