6816 Gall Blvd (3) - Laserfiche WebLink

Browse Search

P-1 PROJECT: PINCHASERS ANTHONY PERRONE 808 1'-6" I 2'-9" L 2'-9" L V-6" L 8" L 5 BOTTLE SHELF DETAIL /2 0 7,-2„ x-n vx, BAR 122 - PLAN DETAIL 1 /2" = 1'-0" I BAR 103 - PLAN DETAIL. 1/2" = 1'-0" CORRIDOR 104 - SOUTH ELEV. 1/4" = 1'-0" BOWLING AREA - NORTH WALL 1/8" = 1'-0" GENERAL MILLWORK NOTES 1. ALL MILLWORK SHALL BE FABRICATED IN STRICT ACCORDANCE WITH THE ARCHITECTURAL WOODWORK INSTITUTE, "ARCHITECTURAL WOODWORK INSTITUTE QUALITY STANDARDS...', CUSTOM GRADE, UNLESS NOTED OTHERWISE. SHOP DRAWINGS ARE REQUIRED TO BE SUBMITTED AND APPROVED FOR ALL MILLWORK ITEMS PRIOR TO FABRICATION. PROVIDE ARCHITECTURAL WOODWORK INSTITUTE QUALITY CERTIFICATION PROGRAM LABELS OR CERTIFICATES INDICATING THAT THE WOODWORK, INCLUDING INSTALLATION, COMPLIES WITH REQUIREMENTS OF GRADES SPECIFIED. THE CONTRACTOR, UPON AWARD OF WORK, SHALL REGISTER THIS PROJECT WITH THE ARCHITECTURAL WOODWORK INSTITUTE QUALITY CERTIFICATION PROGRAM. (800) 449-881 1. 2. VERIFY ALL DIMENSIONS WITH CATALOG CUTS OF ACTUAL HARDWARE AND EQUIPMENT TO BE USED AND FIELD CONDITIONS. COORDINATE ROUGH -IN LOCATIONS WITH FIELD DIMENSIONS PRIOR TO FABRICATION. FIELD CUT COUNTERTOPS FOR INSTALLATION OF EQUIPMENT AND FIXTURES, TYPICAL. 3. SCRIBE AND CUT MILLWORK DURING INSTALLATION AS REQUIRED TO COMPENSATE FOR IRREGULAR WALL AND FLOOR SURFACES. INSTALLATION SHALL BE LEVEL, PLUMB AND TIGHT AT ALL FLOOR AND WALL SURFACES, CAULK ALL JOINTS WITH CLEAR SILICONE SEALANT. 4. PROVIDE WOOD OR SHEET METAL BLOCKING AS REQUIRED CONCEALED IN WALL CONSTRUCTION TO ADEQUATELY SUPPORT MILLWORK FOR ITS INTENDED USE IN THE LOCATIONS SHOWN. 5. ALL DRAWER AND CABINET PULLS SHALL BE AS SELECTED BY OWNER. 6. ALL DRAWERS SHALL HAVE TWO MEDIUM DUTY FULL EXTENSION DRAWER SLIDES AS MANUFACTURED BY "ACCURIDE", MODEL 3832, OR EQUAL. 7. EACH CABINET DOOR UP TO 42" IN HEIGHT SHALL HAVE TWO HINGES WITH 170 DEGREE OPENING AS MANUFACTURED BY "BLUM", MODEL CLIP 170, OR EQUAL. 8. PROVIDE (INSERT QUANTITY) HOLES IN COUNTERTOPS WITH BLACK PLASTIC GROMMETS FOR ELECTRICAL PLUG-IN CONNECTIONS RELATED TO MILLWORK ITEMS. VERIFY EXACT NUMBER AND LOCATIONS IN FIELD WITH OWNER'S REPRESENTATIVE. 9. UNLESS NOTED OTHERWISE, ALL BASE CABINETS/WALL CABINETS/COUNTERS SHALL BE CONSTRUCTED OF 3/4" MEDIUM DENSITY FIBERBOARD WITH PLASTIC LAMINATE FINISH. (SEE DETAILS). 10. UNLESS NOTED OTHERWISE, ALL COUNTERTOPS WITH PLUMBING FIXTURES/ SINKS SHALL BE CONSTRUCTED OF 3/4" MEDEX (WATER RESISTANT HIGH DENSITY FIBERBOARD) WITH PLASTIC LAMINATE FINISH. (SEE DETAILS). 11. UNLESS NOTED OTHERWISE, INTERIOR CONCEALED SURFACES SHALL BE FINISHED WITH MELAMINE (LOW PRESSURE LAMINATE). SUBMIT SAMPLES FOR COLOR SELECTION, IF COLORS ARE NOT SPECIFIED IN DETAILS. 12. BASE CABINETS SHALL BE 2'-0" DEEP, UNLESS OTHERWISE NOTED. WALL CABINETS SHALL BE 1'-2" DEEP, UNLESS OTHERWISE NOTED. 13. PROVIDE CUT-OUTS IN MILLWORK ITEMS AS REQUIRED TO ACCOMMODATE JUNCTION BOXES AND OTHER ELECTRICAL DEVICES AS REQUIRED. COORDINATE WITH DETAILS AND ELECTRICAL DRAWINGS, IF ANY. 14. FOR ALL WOOD VENEER WALL PANELS, CONTRACTOR SHALL VERIFY GRAIN PATTERN CUT AND REPEAT WITH PROJECT DESIGNER PRIOR TO FABRICATION. 15. UNLESS NOTED OTHERWISE, INTERIOR CONCEALED SHELVING SHALL BE MELAMINE (LOW PRESSURE LAMINATE, COLOR TO MATCH CABINETS). EXPOSED SHELVING SHALL BE 3/4" PLYWOOD WITH PLASTIC LAMINATE FINISH. EDGES OF ALL SHELVING SHALL BE FINISHED WITH POLYETHYLENE TEE MOLDING (COLOR TO MATCH CABINETS.) 6816 GALL BOULEVARD ZEPHYRHILLS, FL 33542 PROJECT NUMBER: 21161 ♦ ^ �/ J Co U Co J N O < Lu Lu =U �a °o � W 0 X O LL u CD �O o N �t r ^ �/ I u_J ~ N 06 z U wO LLJ �� N z N �N Lu Q w06 U N 06 N O c>7 uo -mama r- STAMP: ISSUE: DATE: ISSUED FOR PERMIT 01.25.2023 DRAWING SCALE: As indicated DRAWN BY: CHECKED BY: Checker DRAWING TITLE: INTERIOR ELEVATIONS AND PLAN DETAILS SHEET NUMBER: A802 -1 T-