Laserfiche WebLink
A <br />rn <br />b <br />to <br />0 <br />42 <br />0 <br />0 <br />CJ�p <br />ILi <br />0 <br />I <br />cep <br />0 <br />I <br />N <br />0 <br />Crr <br />.�S <br />L0 <br />co <br />0 <br />In <br />0 <br />0 <br />J <br />rn <br />to <br />co <br />0 <br />I <br />ra <br />to <br />to <br />to <br />0 <br />N <br />0 <br />c <br />3 <br />C <br />Q <br />d <br />0 <br />o. <br />E <br />0 <br />0 <br />c <br />N <br />a� <br />L�. <br />0 <br />0 <br />U <br />.a <br />n- <br />i <br />0. <br />U <br />J <br />a� <br />0 <br />N <br />0 <br />0 <br />a <br />N <br />cV <br />co <br />0 <br />0 <br />a <br />m <br />b <br />>N <br />C <br />80 <br />--- ��---------------------------------------------------------------------- <br />TEXTURED <br />FINISH <br />1 H3-SH <br />FLASHING <br />METAL ROOF -- 7�-9" x <br />-- <br />PAD7:12, PITCH <br />---- -------------------------- ------------- +1"PAD ----� <br />HEEL - - - - - - - - - <br />T.O.P. <br />HDR. _ <br />12 <br />F_FL-- V _� <br />EXTERIOR PLASTER <br />ON FRAME------_ <br />BRG_AT GARAGE <br />fLf L. <br />111 <br />2'-2" <br />TEXTURED <br />FINISH---\ <br />"OR <br />12 <br />5� <br />(1787) <br />12 <br />�5 <br />16" BAND <br />12 <br />Q5 <br />------ FLASHING — <br />—. <br />TEXTURED <br />FINISH <br />-------T.O.P.-- <br />HDR. <br />12 <br />V _F.FL___ <br />EXTERIOR PLASTER <br />ON FRAME_ CLG_HGT. <br />B_R_G.ATG <br />2-2" <br />FFL___ <br />LEFT ELEVATION <br />------------------------------------------------------------ ----------- <br />4' 11—_1_4" <br />TEXTURE <br />FINISH <br />1 H3-SH <br />FLASHING <br />-------------- <br />CJ <br />TEXTURE <br />FINISH <br />x T-9" METAL ROOF <br />--- 7:12 PITCH <br />- -----PAD --- ---- -PAD------ <br />- - - <br />-- <br />16" BAND <br />(1787) <br />(2) 39"x59" SH <br />TEXTURED <br />/—FINISH <br />SCALE: 3/16"=1'-0" <br />RIGHT ELEVATION <br />SCALE: 3/16"=1'-0" <br />C <br />00 <br />0 <br />co <br />General Notes <br />ROOF CRITERIA: <br />• 12" OVERHANG U.N.O. <br />• PLUMB CUT FASCIA ROOF <br />• PITCH PER ELEVATION <br />**G.C. VERIFY ROOF PITCH** <br />ROOF PITCH VARIES PER SUBDIVISIONS IT IS THE <br />CONTRACTORS RESPONSIBILITY TO VERIFY <br />ROOF SLOPE REQUIREMENTS WITH TRUSS <br />MANUFACTURER. <br />**ELECTRICAL SPECIFICATION NOTES** <br />ELECTRICAL CONTRACTOR MUST VERIFY WITH <br />THE SPECIFICATIONS FOR THE TYPE OF FIXTURE <br />TO BE USED, LIGHT FIXTURES SHOWN ARE FOR <br />LOCATION PURPOSES. <br />overing <br />R703.7 Exterior Plaster. <br />Installation of these materials shall be in compliance with ASTM <br />C926 and ASTM C1063, or ASTM C1787 and the provisions of <br />this code. <br />R703.7.1 Lath. <br />Lath and Lath attachments shall be of corrosion -resistant <br />materials. Expanded metal or woven wire lath shall be attached <br />with 1-1/2" long, 11 gage nails having <br />a 7/16" head, or 1-1/2" long, 16 gage staples, spaced in <br />accordance with ASTM C1063 or C1787, or as otherwise <br />approved. (Refer to sheet SN1 for the engineered method for <br />Lath attachment.) <br />Lathing Accessories <br />Attachments shall be of corrosion -resistant materials. <br />Wood Application: 16 Ga.x1-1/2" long (3/4%1" crown) staples @ <br />6" O.C. vertically/horizontally into the framing members. <br />Masonry Application: Concrete stub nail, 3/8" (10 mm) head dia. <br />min. @ 6" O.C. vertically/horizontally or compatible adhesives, <br />exterior gun -grade, construction adhesive with 1" dabs @ 6" O.C. <br />or in a semi -continuous bead between the solid plaster base and <br />the solid portion of the key attachment flange. <br />Control Joints: Install control joint lathing accessories in <br />conformance with C1063. Lath shall not be continuous through <br />control joints, but shall be stopped and tied at each side. <br />All accessories shall be in accordance with the latest ASTM <br />C1063 & ASTM C1861. <br />R703.7.2 Plaster. <br />Plastering with cement plaster shall be not less than three coats <br />where applied over any type of code -approved lath and shall be <br />not less than two coats where directly applied over masonry, <br />concrete, clay brick, stone, or tile. If the plaster surface is <br />completely covered by veneer or other facing material or is <br />completely concealed, plaster application need be only two coats, <br />provided total thickness is as set in Table R702.1(1). <br />Cement plaster shall be in accordance with ASTM C926 and <br />material shall be in accordance with one of the types listed in <br />R703.7.2. <br />R703.7.3 Water -Resistive Barriers. <br />Water -resistive barriers shall be installed as required in Section <br />R703.2 and, where applied over wood -based sheathing, shall <br />include a water -resistive vapor -permeable barrier with a <br />performance at least equivalent to two layers of Grade D paper. <br />The individual layers shall be installed independently such that <br />each layer provides a separate continuous plane and any flashing <br />(installed in accordance with Section R703.4) intended to drain to <br />the water -resistive barrier is directed between the layers. <br />R703.2 Water -Resistive Barrier. <br />One layer of No. 15 asphalt felt, free from holes and breaks, <br />complying with ASTM D226 for Type 1 felt or other approved <br />water -resistive barrier shall be applied over studs or sheathing of <br />all exterior walls. No. 15 asphalt felt shall be applied horizontally, <br />with the upper layer lapped over the lower layer not less than 2 <br />inches. Where joints occur, felt shall be lapped not less than 6 <br />inches. Other approved materials shall be installed in accordance <br />with the water -resistive barrier manufacturer's installation <br />instructions. The No. 15 asphalt felt or other approved <br />water -resistive barrier material shall be continuous to the top of <br />walls and terminated at penetrations and building appendages in <br />a manner to meet the requirements of the exterior wall envelope <br />as described in Section R703.1. <br />R703.4 Flashing. <br />Approved metal flashing, vinyl flashing, self -adhered membranes <br />and mechanically attached flexible flashing shall be applied <br />shingle -fashion or in accordance with the manufacturer's <br />instructions. Metal flashing shall be corrosion resistant. <br />Fluid -applied membranes used as flashing shall be applied in <br />accordance with the manufacturer's instructions. All flashing shall <br />be applied in a manner to prevent the entry of water into the wall <br />cavity or penetration of water to the building structural framing <br />components. <br />Self -adhered membranes used as flashing shall comply with <br />AAMA 711. All exterior fenestration products shall be sealed at <br />the juncture with the building wall with a sealant complying with <br />AAMA 800 or ASTM C920 Class 25 Grade NS or greater for <br />proper joint expansion and contraction, ASTM C1281, AAMA 812, <br />or other approved standard as appropriate for the type of sealant. <br />Fluid -applied membranes used as flashing in exterior walls shall <br />comply with AAMA 714. The flashing shall extend to the surface <br />of the exterior wall finish. <br />Approved flashings shall be installed at the following locations. <br />• Exterior window/door openings. <br />• Intersection of chimneys or other masonry construction with <br />frame walls. <br />• Under and at the ends of masonry, wood or metal copings <br />and sills. <br />• Continuously above all projecting wood trim. <br />• Where exterior porches, decks or stairs attach to a wall or <br />floor assembly of wood -frame construction. <br />• At wall and roof intersection. <br />• At Built-in gutters. <br />Coastal Flashings <br />All flashing material for coastal locations (ex: within 3,000 feet of the <br />ocean) shall be corrosion resistant material (ex: zinc and/or stainless <br />steel) and shall be selected for compatibility with adjacent wood <br />preservatives per the manufacturer's recommendations. <br />a <br />? W <br />Cl- <br />-: <br />9 <br />0 <br />o <br />ly !Z <br />SE <br />• --i `• <br />"c <br />U \,�P <br />••• <br />�. ••• F La <br />7 /NPif1!!lillt'��� <br />To the best of the Engineer's knowledge, information and belief, <br />the structural plans and specifications contained within these <br />drawings comply with the 2020 Florida Building Code - <br />Residential 7th Edition. Engineer's signature and seal is only for <br />the structural engineering portions of the drawing pages bearing <br />Engineer's signature and seal. <br />W <br />:. H `ro E <br />.0 Milkg 8 <br />V 0 N r <br />0 ,-0� y <br />N vtr`r`� u <br />:i N O r1 <br />Q C J u- <br />W <br />U- IL <br />J <br />- -d � a 4 <br />Z m c rn <br />r mpg 8 <br />��m p Y <br />W <br />_' N C0 Z <br />LL <br />t7 <br />U Oa o <br />Z <br />y� W a o <br />z N M <br />0 <br />z <br />Q � a <br />v <br />UZON <br />- <br />E3 <br />M <br />U) <br />N z <br />u- <br />a-1 <br />V <br />OLU g <br />V) c w <br />�N <br />U <br />L" <br />9 <br />U ° <br />ta, U) m <br />4 N O <br />m <br />�� <br />ti <br />C:,� <br />W <br />M <br />Z¢ <br />U- <br />E <br />z. <br />>� <br />�� <br />Q 0 <br />E V <br />w� <br />_0 <br />CU <br />I— <br />Ko <br />0 <br />0U <br />0 <br />G7 <br />N <br />ap <br />w0 <br />ao <br />d Z <br />¢ <br />_ L <br />� � <br />y <br />m� <br />�Z <br />m <br /><� <br />¢ w <br />�Z <br />N 3 <br />0< <br />30 <br />a <br />�w <br />o <br />0 <br />0 <br />C.0 <br />tiw <br />=14 <br />�ti <br />0 <br />o T <br />> (� <br />I^ <br />m <br />Q <br />cc <br />r <br />O <br />L7 <br />Ln <br />E-- <br />N <br />C-0 <br />� <br />Q <br />O <br />,— <br />Ob <br />Cr <br />Lfl <br />.�— <br />120 <br />(� <br />Q <br />N <br />LICE <br />.S� O <br />Q <br />N <br />LO <br />C <br />r <br />� <br />Z <br />m <br />z <br />E ID <br />m <br />c <br />cc <br />o. <br />E -• v <br />U 0 Q p <br />c <br />c <br />a) <br />JOB <br />NO: 22-06569-06566 <br />SCALE : AS NOTED <br />SHEET NO. <br />9.1 <br />