|
THESE DETAILS ARE GENERIC AND
<br />MEANT TO SHOW GENERAL FLASHING
<br />AND WATERPROOFING METHODS TO
<br />BE USED.
<br />3/8" CEMENT
<br />PLASTER
<br />12 MIL DRYLOK
<br />CMU - MASONRY BLOCK
<br />EXTREME
<br />WINDOW
<br />FASTENER
<br />1) SEALANT AT
<br />4) SEALANT JOINT
<br />WINDOW BUCK TO
<br />OUTSIDE EDGE OF
<br />MASONRY
<br />WINDOW BUCK
<br />t
<br />2) SEALANT JOINT
<br />AWINDOW
<br />5) SEALANT FROM
<br />INSIDE EDGE OF
<br />WINDOW FRAME
<br />BUCK
<br />ACROSS WINDOW BUCK
<br />AND EXTEND TO
<br />WINDOW FRAME
<br />MASONRY
<br />ATTACHED
<br />PER CODE
<br />6) TOOLED SEALANT
<br />REQUIREMENTS
<br />BEAD BRIDGING
<br />CLADDING AND WINDOW
<br />FRAME
<br />3) SEALANT WINDOW FRAME TO
<br />WINDOW BUCK ALL THE WAY
<br />AROUND, INCLUDING SILL.
<br />SCS 06_05 CMU INSTALLATION 6 POINT BUCK AND
<br />FENESTRATION INSTALLATION AND INTERFACE
<br />JAMB, SILL AND HEAD DETAIL
<br />APPROVED SHEATHING
<br />APPROVED HOUSEWRAP
<br />STRUCTALATH TWIN TRACK 2.5
<br />3/4" CEMENT PLASTER
<br />12 MIL (min) DRYLOK EXTREME
<br />APPROVED FLASHING TAPE
<br />W" SEALANT SOCKET WITH
<br />TOOLED APPROVED SEALANT
<br />SCS 06_02 WINDOW FIN INTERFACE WITH
<br />EXTRUDED SHOULDER
<br />WEATHER
<br />SRESISITIVE
<br />BARRIER
<br />TAPE
<br />(ASSEMBLED WINDOW 7
<br />HEAD FLASHING TIE-IN INSTRUXTIC
<br />1. Cut, fold up & temporarily secure I
<br />resistive barrier above header to allow for
<br />flashing installation
<br />2. Self -adhered flashing plus head flashing under
<br />weather resistive barrier
<br />3. Fold weather resistive barrier back over head
<br />flashing and seal with tape
<br />E`
<br />DO NO'
<br />BOTTO
<br />❑I nnlr_�.
<br />�nI n I Io WEATHER
<br />✓E BARRIER &
<br />IARILY SECURE
<br />SELF -ADHERED FLASHING Scale: NITS
<br />FLANGED WINDOW
<br />FLASHING INSTALLATION AFTER WEATHER RESISTIVE BARRIER
<br />SELF -ADHERED FLASHING
<br />HALF ROUND WINDOW
<br />SELF -ADHERED FLASHING
<br />PRODUCTS DETAILS
<br />TWO LAYERS OF FELT OR ONE LAYER OF HOUSE WRAP AND
<br />ONE LAYER OF FELT ARE REQUIRED BEHIND STUCCO. FBC
<br />R703.2.1 AND FBCR 703.7.3
<br />Detail Instructions
<br />Refer to the number marked asEin each detail that corresponds to the
<br />numbered items in the list of instructions below:
<br />1. Install self -adhered flashing in order as shown by numbers
<br />2. Install flashing and weather resistive barrier to form water shedding
<br />laps
<br />3. Self -adhered flashing can be substituted for building paper
<br />4. Split the release paper using the ripcord (Split release on demand,
<br />embedded in the adhesive layer) - for ease of installation and to
<br />minimize scoring cuts
<br />5. Remove all release paper per standard installation instructions and
<br />adhere to substrate using a square piece of flashing material (6" x 6"
<br />Minimum)
<br />6. Fold as shown by arrows
<br />7. Angle of corner may vary, adjust folding of the flashing accordingly to
<br />fit tight to corner
<br />8. Mechanically fasten as necessary
<br />WOOD FRAME CONSTR.
<br />EXTERIOR SELF -ADHERED FLASHIN
<br />SHEATHING BY LAPPING DOWN -�
<br />OVER RIM JOIST AND UP
<br />WALL BY 6 IN.
<br />WEATHER
<br />RESISITIVE
<br />BARRIER SEAL TOPS OF JOI:
<br />UNDER DECKING
<br />ED FLASHING (SEE DETAIL WP07)
<br />4SHING
<br />E
<br />AM
<br />rr.n�nuvia r�r��nlrvu O
<br />2
<br />SELF -ADHERED FLASHING
<br />DECK JOIST
<br />2x FRAMEWALL
<br />TILE FINISH
<br />1/2" DUROCK-
<br />V-4" PER PLAN
<br />1'-0" PER PLAN
<br />8" CMU
<br />4"OR8"CMU - °
<br />(PER SEAT DEPTH) °
<br />FILL WITH GROUT a
<br />°
<br />SLOPED MUD BED ° °
<br />VINYL SHOWER PAN
<br />H
<br />SLOPE
<br />°
<br />4
<br />a
<br />SHOWER SEAT
<br />WEATHER RESISTIVE
<br />BARRIER
<br />SELF -ADHERED FLASHING
<br />EXTERIOR DOOR WITH DECK - SECTION A
<br />EXTERIOR SHEATHING
<br />3/4%1" BEAD OF CONSTR.
<br />ADHESIVE TO BE APPLIED UNDER
<br />THRESHOLD OF DOOR AND RETURN
<br />UP JAMB 6". USE LIQUID NAIL BRAND
<br />OR EQUAL WEATHER PROOF CAULKING
<br />SECTION -A (SEE DETAIL WP02)
<br />SELF -ADHERED FLASHING v
<br />C
<br />SEAL TOPS OF JOISTS
<br />UNDER DECKING
<br />(SEE DETAIL WP07)
<br />SELF -ADHERED FLASHING
<br />EXTERIOR DOOR WITH DECK
<br />SELF-ADHER
<br />SELF -ADHERED FLASHING
<br />OUTSIDE CORNER
<br />Z
<br />= W
<br />C7 U
<br />W w
<br />Q Lu
<br />w
<br />Lu
<br />O
<br />U)
<br />DOOR ROUGH OPENING
<br />- 3/4"-1" BEAD OF CONSTR.
<br />ADHESIVE TO BE APPLIED UNDER
<br />THRESHOLD OF DOOR AND
<br />RETURN UP JAMB 6". USE LIQUID
<br />NAIL BRAND OR EQUAL WEATHER
<br />PROOF CAULKING
<br />SELF -ADHERED FLASHING
<br />SUBFLOOR
<br />RIM JOIST
<br />WINDOW UNIT
<br />FLASHING REQUIREMENTS
<br />SLOPE
<br />0.3 in: 12.0 in
<br />R703.1 General. Exterior walls shall provide the building with a weather -resistant exterior wall envelope. The exterior wall envelope shall
<br />(0.6 cm: 30.5 cm)
<br />include flashing as described in Section R703.4. A water -resistive barrier is described as a material behind an exterior wall covering that is
<br />SELF -ADHERED FLASHING
<br />intended to resist liquid water that has penetrated behind the exterior covering from further intruding into the exterior wall assembly. An
<br />exterior wall covering is described as a material or assembly of materials applied on the exterior side of exterior walls for the purpose of
<br />EXTERIOR
<br />providing a weather -resistive barrier, insulation, or for aesthetics, including but not limited to, veneers, siding, exterior insulation and finish
<br />CEMT. FIN.
<br />systems, architectural trim and embellishments such as cornices, soffits, and fascias.
<br />BUILDING PAPER
<br />WIRE LATH
<br />R703.2 Water -resistive barrier, One layer of No. 15 asphalt felt, free from holes and breaks, complying with ASTM D226 for Type 1 felt or
<br />other approved water -resistive barrier shall be applied over studs or sheathing of all exterior walls. Such felt or material shall be applied
<br />horizontally, with the upper layer lapped over the lower layer not less than 2 inches (51 mm). Where joints occur, felt shall be lapped not less
<br />than 6 inches (152 mm). The felt or other approved material shall be continuous to the top of walls and terminated at penetrations and
<br />building appendages in a manner to meet the requirements of the exterior wall envelope as described in Section R703.1.
<br />R703.7.3 Water -resistive barriers shall be installed as required in Section R703.2 and, where applied over wood -based sheathing, shall
<br />include a water -resistive vapor -permeable barrier with a performance at least equivalent to two layers of Grade D paper. The individual
<br />2
<br />layers shall be installed independently such that each layer provides a separate continuous plane and any flashing (installed in accordance
<br />with Section R703.4) intended to drain to the water -resistive barrier is directed between the layers.
<br />Exception: Where the water -resistive barrier that is applied over wood -based sheathing has a water resistance equal to or greater
<br />1
<br />SELF -ADHERED FLASHING ,
<br />CEMT. FINISH SILL/ POTSHELF/ CHIMNEY SHOULDER
<br />than that of 60-minute Grade D paper and is separated from the stucco by an intervening, substantially nonwater-absorbing layer or
<br />designed drainage space.
<br />R703.4 Flashing. Approved corrosion -resistant flashing shall be applied shingle -fashion in a manner to prevent entry of water into the wall
<br />MECHANICALLY FASTEN IF RUBBERIZED RUBBERIZED ASPHALT
<br />NEEDED IN CORNERS ADHESIVE
<br />INSTALL SELF -ADHERED
<br />THROUGH SELF -ADHERED ASPHALT ADHESIVE
<br />cavityor penetration of water to the buildingstructural framingcomponents. Self -adhered membranes used as flashingshall comply with
<br />p p y
<br />FLASHING JAMB & HEAD
<br />FLASHING, SEE
<br />FLASHING SELF -ADHERED FLASHING
<br />AAMA 711. All exterior fenestration products shall be sealed at the juncture with the building wall with a sealant complying with AAMA 800 or
<br />FLANGED WINDOW
<br />(SEE DETAIL WP01)
<br />ASTM C920 Class 25 Grade NS or greater for proper joint expansion and contraction, ASTM C1281, AAMA 812, or other approved standard
<br />g p p 1 p pp
<br />SCORED
<br />as appropriate for the type of sealant. Fluid -applied membranes used as flashing in exterior walls shall comply with AAMA 714. The flashing
<br />RELEASE PAPER
<br />shall extend to the surface of the exterior wall finish. Approved corrosion resistant flashings shall be installed at the following locations:
<br />' �`� (BEFORE FOLDING, SCORE
<br />1. Exterior window and door openings. Flashing at exterior window and door openings shall extend to the surface of the exterior wall
<br />SELF -ADHERED FLASHING,
<br />EXTEND A MINIMUM 6"
<br />RELEASE PAPER TO ADHESIVE AS SHOWN)
<br />finish or to the water -resistive barrier complying with Section 703.2 for subsequent drainage. Mechanically attached flexible flashings
<br />VERTICALLY FROM
<br />BOTTOM OF
<br />THRESHOLD
<br />:LF-ADHERED FLASHING
<br />TCH
<br />HERED FLASHING
<br />1
<br />2
<br />4
<br />5
<br />ml
<br />wo, 'Amn
<br />PLASTER STOP -
<br />CONTINUOUS BACKER -
<br />ROD & SEALANT
<br />A
<br />ON
<br />SELF -ADHERED FLASHING
<br />INSIDE CORNER
<br />�Ground�
<br />FOUNDATION WEEP SCREED
<br />STRIP OF SAF
<br />DRAINAGE PLANE WRB
<br />BOND BREAK WRB
<br />SF LATH
<br />WRAP DP WRB ONTO
<br />THE VERTICAL
<br />SURFACE TO TOP OF
<br />FLANGE AS AN AIR
<br />BARRIER
<br />3-1/2" INCH FLANGE
<br />THIS GAP IS A RESULT OF
<br />NATURAL SHRINKAGE.
<br />DO NOT SEAL.
<br />DRIP SCREED PLASTIC
<br />ACCESSORY
<br />SOFFIT/CANTILEVER
<br />shall comply with AAMA 712. Flashing at exterior window and door openings shall be installed in accordance with one or more of the
<br />following:
<br />1.1 The fenestration manufacturer's installation and flashing instructions, or for applications not addressed in the fenestration
<br />manufacturer's instructions, in accordance with the flashing manufacturer's instructions. Where flashing instructions or
<br />details are not provided, pan flashing shall be installed at the sill of exterior window and door openings. Pan flashing shall be
<br />sealed or sloped in such a manner as to direct water to the surface of the exterior wall finish or to the water resistive barrier
<br />for subsequent drainage. Openings using pan flashing shall incorporate flashing or protection at the head and sides.
<br />5 1.2. In accordance with the flashing design or method of a registered design professional.
<br />4 1.3. In accordance with other approved methods.
<br />6 1.4 In accordance with FMA/AAMA 100, FMA/ AAMA 200, FMA/WDMA 250, FMA/AAMA/ WDMA 300 or FMA/AAMA/WDMA
<br />21400.
<br />7 2. At the intersection of chimneys or other masonry construction with frame or stucco walls, with projecting lips on both sides under
<br />stucco copings.
<br />' • 3. Under and at the ends of masonry, wood or metal copings and sills.
<br />4. Continuously above all projecting wood trim.
<br />5. Where exterior porches, decks or stairs attach to a wall or floor assembly of wood -frame construction.
<br />6. At wall and roof intersections.
<br />7. At built-in autters.
<br />Water Resistant Barrier
<br />Lath
<br />Sheathing
<br />Stucco
<br />LEGEND
<br />SELF ADHERED FLASHING (SAF) � a
<br />DRAINAGE PLANE (DP) WEATHER RESISTANT
<br />BARRIER (WRB) - -
<br />BOND BREAK WEATHER RESISTANT BARRIER - -
<br />SELF FURRING (SF) LATH
<br />PLASTER ACCESSORY
<br />SHEATHING,'OSB', PLYWOOD, DENSGL4SS
<br />\STER STOP p
<br />NTINUOUS BACKER ROD
<br />EALANT
<br />MENTITIOUS FINISH
<br />RAL FRAMING
<br />RAL SHEATHING
<br />SAF
<br />PLANE WRB
<br />.AK WRB
<br />THESE DETAILS ARE GENERIC AND MEANT TO SHOW GENERAL
<br />FLASHING AND WATERPROOFING METHODS TO BE USED.
<br />Cement Plaster
<br />in accordance
<br />with ASTMC926
<br />over wood 2nd
<br />floor
<br />Cement
<br />Plaster
<br />over block
<br />1 st floor
<br />7/8" Cement Plaster
<br />in accordance with
<br />ASTMC926
<br />Felt backed metal
<br />lathe in accordance
<br />with ASTMC1063
<br />Building Paper
<br />7/16" O.S.B.
<br />sheathing
<br />Metal
<br />Flashing
<br />Weep Screed
<br />Installed As Per
<br />Manufact. Specs.
<br />Maintain
<br />Bottom of
<br />Weep Screed
<br />1 1/2" to 2"
<br />Above Roof
<br />Sheathing
<br />Note:
<br />The building paper and metal lath must be
<br />installed over the top of the weep screed.
<br />WEEP SCREED DETAIL
<br />SCALE: NOT TO SCALE
<br />7/8" Cement Plaster
<br />in accordance with
<br />ASTMC926
<br />Felt backed metal
<br />lathe in accordance
<br />with ASTMC1063
<br />Building Paper
<br />7/16" O.S.B.
<br />sheathing
<br />_Stampede or similar
<br />caulk bottom
<br />joint only
<br />Weep Screed
<br />Installed As Per
<br />Manufact. Specs.
<br />1/2" Cementitious
<br />Decorative Finish
<br />All inside and
<br />outside corner will
<br />need to be miter
<br />cut and caulked all
<br />butt joints need to
<br />becaulked using
<br />Stampede or sim.
<br />caulk for all
<br />�l
<br />U
<br />lJL
<br />/
<br />(Q
<br />F�
<br />0
<br />C4
<br />o_
<br />O
<br />0
<br />To the best of the Engineers knowledge, information and belief,
<br />the structural plans and specifications contained
<br />within these)
<br />drawings comply with the 2017
<br />Florida Building Code -
<br />Residential 6th Edition. Engineers signature and
<br />seal is only for
<br />the structural engineering portions of the drawing
<br />pages bearing
<br />Engineer's signature and seal.
<br />W
<br />,Wg
<br />ay
<br />d E
<br />o � 8
<br />D p°p°
<br />c 4
<br />0
<br />m
<br />d
<br />1 a)J
<br />J
<br />N L
<br />7-
<br />U)N N
<br />W
<br />u d
<br />Q6::
<br />j M 'M
<br />NLLW
<br />W '
<br />° a�
<br />P:
<br />Jam
<br />zo
<br />Z
<br />@C�
<br />L:2
<br />5'MN(0
<br />= m O
<br />m m
<br />W
<br />F� W
<br />o2nrn
<br />U5
<br />Z
<br />N co Z
<br />Q
<br />(J 0 J
<br />OU ❑❑❑
<br />W
<br />V M
<br />0 0
<br />z
<br />z o
<br />to
<br />- N
<br />(D z9
<br />1,
<br />�T
<br />L
<br />C/3
<br />U w
<br />U �
<br />0-,
<br />O
<br />cn
<br />un
<br />w o
<br />urs
<br />(U
<br />U
<br />w J
<br />F^ _ E
<br />l"
<br />ml
<br />'?
<br />I
<br />f
<br />rn w
<br />Oo
<br />Offi-
<br />Cl)
<br />M
<br />o
<br />Z
<br />a
<br />4
<br />J
<br />cE
<br />E 0
<br />y tt
<br />os��
<br />F=
<br />2
<br />zb
<br />D a
<br />-C1�<
<br />E
<br />K O
<br />OU
<br />g�
<br />xQ
<br />ZN
<br />¢o
<br /><
<br />a
<br />rw
<br />L
<br />W _
<br />co
<br />z
<br />.
<br />m 0
<br />o
<br />O,
<br />Z�
<br />ZI
<br />W
<br />°
<br />o 12
<br />w
<br />1z
<br />3z
<br />Q
<br />T
<br /><
<br />a z
<br />N
<br />U
<br />o
<br />-P
<br />oz
<br />r
<br />=3
<br />CD
<br />mia
<br />oQ
<br />°
<br />�M
<br />0
<br />In
<br />> d-
<br />L,
<br />WAl
<br />�
<br />J
<br />M
<br />N
<br />.-.
<br />a)O
<br />ca
<br />U
<br />Cb
<br />U
<br />T
<br />CN
<br />U o
<br />=
<br />I N
<br />T r
<br />�
<br />r
<br />M
<br />o) rn
<br />E
<br />Z
<br />c
<br />N
<br />2
<br />Z
<br />E
<br />E O
<br />a
<br />ci 1
<br />¢ o
<br />JOB
<br />NO:
<br />20-65
<br />4
<br />SCALE :
<br />AS NOTItD
<br />SHEET NO.
<br />W P
<br />
|