|
Q
<br />4
<br />00
<br />0
<br />co
<br />0
<br />U
<br />0.
<br />ID
<br />L7
<br />N
<br />0
<br />LO
<br />,o
<br />0
<br />THESE DETAILS ARE GENERIC AND
<br />MEANT TO SHOW GENERAL FLASHING
<br />AND WATERPROOFING METHODS TO
<br />BE USED.
<br />3/8" CEMENT
<br />PLASTER
<br />12 MIL DRYLOK CMU - MASONRY BLOCK
<br />EXTREME
<br />WINDOW
<br />FASTENER
<br />1) SEALANT AT
<br />4) SEALANT JOINT
<br />WINDOW BUCK TO
<br />OUTSIDE EDGE OF
<br />` ''
<br />MASONRY
<br />WINDOW BUCK
<br />R.:
<br />2) SEALANT JOINT
<br />5) SEALANT FROM
<br />INSIDE EDGE OF
<br />WINDOW FRAME
<br />WINDOW BUCK
<br />ACROSS WINDOW BUCK
<br />AND EXTEND TO
<br />WINDOW FRAME
<br />MASONRY
<br />ATTACHED
<br />PER CODE
<br />6) TOOLED SEALANT
<br />REQUIREMENTS
<br />BEAD BRIDGING
<br />CLADDING AND WINDOW
<br />FRAME
<br />3) SEALANT WINDOW FRAME TO
<br />WINDOW BUCK ALL THE WAY
<br />AROUND, INCLUDING SILL.
<br />SCS 06_05 CMU INSTALLATION 6 POINT BUCK AND
<br />FENESTRATION INSTALLATION AND INTERFACE
<br />JAMB, SILL AND HEAD DETAIL
<br />APPROVED SHEATHING
<br />APPROVED HOUSEWRAP
<br />STRUCTALATH TWIN TRACK 2.5
<br />3/4" CEMENT PLASTER
<br />12 MIL (min) DRYLOK EXTREME
<br />APPROVED FLASHING TAPE
<br />"V" SEALANT SOCKET WITH
<br />TOOLED APPROVED SEALANT
<br />SCS 06_02 WINDOW FIN INTERFACE WITH
<br />EXTRUDED SHOULDER
<br />WEATHER
<br />`RESISITIVE
<br />BARRIER
<br />HEAD FLASHING TIE-IN INSTRUXTIC
<br />1. Cut, fold up & temporarily secure
<br />resistive barrier above header to allow for
<br />flashing installation
<br />2. Self -adhered flashing plus head flashing under
<br />weather resistive barrier
<br />3. Fold weather resistive barrier back over head
<br />flashing and seal with tape
<br />SELF -ADHERED FLASHING Scale: NTS
<br />FLANGED WINDOW
<br />FLASHING INSTALLATION AFTER WEATHER RESISTIVE BARRIER
<br />EXTERIOR SHEATHING
<br />REFER TO TECHNICAL
<br />LETTER ON CHEMICAL
<br />COMPATIBILITY
<br />SELF -ADHERED FLASHING
<br />DO NOT FLASH OVER
<br />BOTTOM NAILING
<br />FLANGE
<br />NAILING FLANGE
<br />SELF -ADHERED FLASHING
<br />HALF ROUND WINDOW
<br />SELF -ADHERED FLASHING
<br />PRODUCTS DETAILS
<br />TWO LAYERS OF FELT OR ONE LAYER OF HOUSE WRAP AND
<br />ONE LAYER OF FELT ARE REQUIRED BEHIND STUCCO. FBC
<br />R703.2.1 AND FBCR 703.7.3
<br />Detail Instructions
<br />Refer to the number marked as G in each detail that corresponds to the
<br />numbered items in the list of instructions below:
<br />1. Install self -adhered flashing in order as shown by numbers
<br />2. Install flashing and weather resistive barrier to form water shedding
<br />laps
<br />3. Self -adhered flashing can be substituted for building paper
<br />4. Split the release paper using the ripcord (Split release on demand,
<br />embedded in the adhesive layer) - for ease of installation and to
<br />minimize scoring cuts
<br />5. Remove all release paper per standard installation instructions and
<br />adhere to substrate using a square piece of flashing material (6" x 6"
<br />Minimum)
<br />6. Fold as shown by arrows
<br />7. Angle of corner may vary, adjust folding of the flashing accordingly to
<br />fit tight to corner
<br />8. Mechanically fasten as necessary
<br />r L/'iJl 111 V 1a
<br />SELF -ADHERED FLASHING
<br />DECK JOIST
<br />WEATHER
<br />dE BARRIER &
<br />1ARILY SECURE
<br />WOOD FRAME CONSTR.
<br />EXTERIOR SELF -ADHERED FLASHIN
<br />SHEATHING BY LAPPING DOWN ----
<br />OVER RIM JOIST AND UP
<br />WALL BY 6 IN.
<br />WEATHER
<br />RESISITIVE
<br />BARRIER SEAL TOPS OF JOI;
<br />UNDER DECKING
<br />ED FLASHING (SEE DETAIL WP07)
<br />1�0
<br />SELF -ADHERED FLASHING
<br />r 6f1Jl IIIVIi
<br />2x FRAMEWALL
<br />TILE FINISH-
<br />1/2" DUROCK-
<br />8" CMU
<br />4"OR8"CMU
<br />(PER SEAT DEPTH)
<br />FILL WITH GROUT -
<br />SLOPED MUD BED -
<br />VINYL SHOWER PAN
<br />SLOP
<br />a
<br />4
<br />a
<br />WEATHER RESISTIVE
<br />BARRIER
<br />SELF -ADHERED FLASHING
<br />EXTERIOR DOOR WITH DECK - SECTION A
<br />EXTERIOR SHEATHING
<br />3/4%1" BEAD OF CONSTR.
<br />ADHESIVE TO BE APPLIED UNDER
<br />THRESHOLD OF DOOR AND RETURN
<br />UP JAMB 6". USE LIQUID NAIL BRAND
<br />OR EQUAL WEATHER PROOF CAULKING
<br />SECTION -A (SEE DETAIL
<br />SELF -ADHERED FLASHING
<br />O.
<br />2 SEAL TOPS OF JOISTS
<br />UNDER DECKING
<br />(SEE DETAIL WP07)
<br />SELF -ADHERED FLASHING
<br />EXTERIOR DOOR WITH DECK
<br />V 4" PER PLAN
<br />1'-0" PER PLAN
<br />SHOWER SEAT
<br />a
<br />J 4
<br />4
<br />Q
<br />W
<br />CO
<br />>
<br />m
<br />SELF -ADHERED FLASHING
<br />OUTSIDE CORNER
<br />ICn
<br />�- DOOR ROUGH OPENING
<br />- 3/4"-1" BEAD OF CONSTR.
<br />ADHESIVE TO BE APPLIED UNDER
<br />THRESHOLD OF DOOR AND
<br />RETURN UP JAMB 6". USE LIQUID
<br />NAIL BRAND OR EQUAL WEATHER
<br />PROOF CAULKING
<br />SELF -ADHERED FLASHING
<br />SUBFLOOR
<br />RIM JOIST
<br />8 2
<br />WINDOW UNIT
<br />SLOPE
<br />0.3 in: 12.0 in
<br />(0.6 cm : 30.5 cm)
<br />SELF -ADHERED FLASHI
<br />EXTERIOR
<br />CEMT. FIN.
<br />BUILDING PAPER
<br />WIRE LATH
<br />SELF -ADHERED FLASHING
<br />CEMT. FINISH SILL/ POTSHELF/ CHIMNEY SHOULDER
<br />MECHANICALLY FASTEN IF RUBBERIZED RUBBERIZED ASPHALT
<br />INSTALL SELF -ADHERED NEEDED IN CORNERS ASPHALT ADHESIVE ADHESIVE
<br />FLASHING JAMB & HEAD THROUGH SELF -ADHERED
<br />FLASHING, SEE FLASHING SELF -ADHERED FLASHING
<br />FLANGED WINDOW
<br />(SEE DETAIL WP01)
<br />SELF -ADHERED FLASHING,
<br />EXTEND A MINIMUM 6"
<br />VERTICALLY FROM
<br />BOTTOM OF
<br />THRESHOLD
<br />:LF-ADHERED FLASHING
<br />kTCH
<br />HERED FLASHING
<br />2
<br />4
<br />5
<br />a
<br />FLASHING REQUIREMENTS
<br />R703.1 General. Exterior walls shall provide the building with a weather -resistant exterior wall envelope. The exterior wall envelope shall
<br />include flashing as described in Section R703.4. A water -resistive barrier is described as a material behind an exterior wall covering that is
<br />NG intended to resist liquid water that has penetrated behind the exterior covering from further intruding into the exterior wall assembly. An
<br />exterior wall covering is described as a material or assembly of materials applied on the exterior side of exterior walls for the purpose of
<br />providing a weather -resistive barrier, insulation, or for aesthetics, including but not limited to, veneers, siding, exterior insulation and finish
<br />systems, architectural trim and embellishments such as cornices, soffits, and fascias.
<br />R703.2 Water -resistive barrier. One layer of No. 15 asphalt felt, free from holes and breaks, complying with ASTM D226 for Type 1 felt or
<br />other approved water -resistive barrier shall be applied over studs or sheathing of all exterior walls. Such felt or material shall be applied
<br />horizontally, with the upper layer lapped over the lower layer not less than 2 inches (51 mm). Where joints occur, felt shall be lapped not less
<br />than 6 inches (152 mm), The felt or other approved material shall be continuous to the top of walls and terminated at penetrations and
<br />building appendages in a manner to meet the requirements of the exterior wall envelope as described in Section R703.1.
<br />R703.7.3 Water -resistive barriers shall be installed as required in Section R703.2 and, where applied over wood -based sheathing, shall
<br />include a water -resistive vapor -permeable barrier with a performance at least equivalent to two layers of Grade D paper. The individual
<br />O layers shall be installed independently such that each layer provides a separate continuous plane and any flashing (installed in accordance
<br />with Section R703.4) intended to drain to the water -resistive barrier is directed between the layers.
<br />Exception: Where the water -resistive barrier that is applied over wood -based sheathing has a water resistance equal to or greater
<br />' than that of 60-minute Grade D paper and is separated from the stucco by an intervening, substantially nonwater-absorbing layer or
<br />designed drainage space.
<br />R703.4 Flashing. Approved corrosion -resistant flashing shall be applied shingle -fashion in a manner to prevent entry of water into the wall
<br />cavity or penetration of water to the building structural framing components. Self -adhered membranes used as flashing shall comply with
<br />AAMA 711. All exterior fenestration products shall be sealed at the juncture with the building wall with a sealant complying with AAMA 800 or
<br />ASTM C920 Class 25 Grade NS or greater for proper joint expansion and contraction, ASTM C1281, AAMA 812, or other approved standard
<br />SCORED as appropriate for the type of sealant. Fluid -applied membranes used as flashing in exterior walls shall comply with AAMA 714. The flashing
<br />' RELEASE PAPER shall extend to the surface of the exterior wall finish. Approved corrosion resistant fleshings shall be installed at the following locations:
<br />(BEFORE FOLDING, SCORE 1. Exterior window and door openings. Flashing at exterior window and door openings shall extend to the surface of the exterior wall
<br />RELEASE PAPER TO EXPOSE
<br />ADHESIVE AS SHOWN) finish or to the water -resistive barrier complying with Section 703 2 for subsequent drainage Mechanically attached flexible fleshings
<br />SELF -ADHERED FLASHING
<br />INSIDE CORNER
<br />Ground
<br />FOUNDATION WEEP SCREED
<br />STRIP OF SAF
<br />DRAINAGE PLANE WRB
<br />BOND BREAK WRB
<br />SF LATH
<br />WRAP DP WRB ONTO
<br />:'T THE VERTICAL
<br />SURFACE TO TOP OF
<br />FLANGE AS AN AIR
<br />BARRIER
<br />3-1/2" INCH FLANGE
<br />II
<br />rya �v
<br />7PLASTERPTHIS GAP IS ARESULT OF
<br />NATURAL SHRINKAGE.
<br />DO NOT SEAL.
<br />ER
<br />ROD & SEALANT DRIP SCREED PLASTIC
<br />ACCESSORY
<br />A
<br />SOFFIT/CANTILEVER
<br />shall comply with AAMA 712. Flashing at exterior window and door openings shall be installed in accordance with one or more of the
<br />following:
<br />1.1 The fenestration manufacturer's installation and flashing instructions, or for applications not addressed in the fenestration
<br />manufacturer's instructions, in accordance with the flashing manufacturer's instructions. Where flashing instructions or
<br />details are not provided, pan flashing shall be installed at the sill of exterior window and door openings. Pan flashing shall be
<br />2 sealed or sloped in such a manner as to direct water to the surface of the exterior wall finish or to the water resistive barrier
<br />for subsequent drainage. Openings using pan flashing shall incorporate flashing or protection at the head and sides.
<br />5 1.2. In accordance with the flashing design or method of a registered design professional.
<br />4 1.3. In accordance with other approved methods.
<br />6 1.4 In accordance with FMA/AAMA 100, FMA/ AAMA 200, FMA/WDMA 250, FMA/AAMA/ WDMA 300 or FMA/AAMA/WDMA
<br />400.
<br />2. At the intersection of chimneys or other masonry construction with frame or stucco walls, with projecting lips on both sides under
<br />stucco copings.
<br />• 3. Under and at the ends of masonry, wood or metal copings and sills.
<br />4. Continuously above all projecting wood trim.
<br />5. Where exterior porches, decks or stairs attach to a wall or floor assembly of wood -frame construction.
<br />6. At wall and roof intersections.
<br />7. At built-in autters.
<br />Water Resistant Barrier
<br />Lath
<br />Sheathing
<br />Stucco
<br />LEGEND
<br />SELF ADHERED FLASHING (SAF) -0 o
<br />DRAINAGE PLANE (DP) WEATHER RESISTANT
<br />BARRIER (WRB) - -
<br />BOND BREAK WEATHER RESISTANT BARRIER- -
<br />SELF FURRING (SF) LATH
<br />PLASTER ACCESSORY
<br />SHEATHING,'OSB', PLYWOOD, DENSGLASS�A
<br />\STER STOP A
<br />NTINUOUS BACKER ROD
<br />EALANT
<br />UENTITIOUS FINISH
<br />2AL FRAMING
<br />?AL SHEATHING
<br />3AF
<br />PLANE WRB
<br />AK WRB
<br />FHESE DETAILS ARE GENERIC AND MEANT TO SHOW GENERAL
<br />FLASHING AND WATERPROOFING METHODS TO BE USED.
<br />Cement Plaster
<br />in accordance
<br />with ASTMC926
<br />over wood 2nd
<br />floor
<br />Cement
<br />Plaster
<br />over block
<br />1 st floor
<br />7/8" Cement Plaster
<br />in accordance with
<br />ASTMC926
<br />Felt backed metal
<br />lathe in accordance
<br />with ASTMC1063
<br />Building Paper
<br />-7/16" O.S.B.
<br />sheathing
<br />Metal
<br />Flashing
<br />Weep Screed
<br />Installed As Per
<br />Manufact. Specs.
<br />Maintain
<br />Bottom of
<br />Weep Screed
<br />1 1/2"to 2"
<br />Above Roof
<br />Sheathing
<br />Note:
<br />The building paper and metal lath must be
<br />installed over the top of the weep screed.
<br />WEEP SCREED DETAIL
<br />SCALE: NOT TO SCALE
<br />7/8" Cement Plaster
<br />in accordance with
<br />ASTMC926
<br />Felt backed metal
<br />lathe in accordance
<br />with ASTMC1063
<br />Building Paper
<br />7/16" O.S.B.
<br />sheathing
<br />Stampede or similar
<br />cauk bottom
<br />joint only
<br />Weep Screed
<br />Installed As Per
<br />Manufact. Specs.
<br />1/2" Cementitious
<br />Decorative Finish
<br />All inside and
<br />outside corner will
<br />need to be miter
<br />cut and caulked all
<br />butt joints need to
<br />becaulked using
<br />Stampede or sim.
<br />caulk for all
<br />A,
<br />'
<br />r
<br />I
<br />0
<br />c14
<br />0
<br />CV
<br />M
<br />CV
<br />0
<br />To the best of the Engineer's knowledge, information and belief,
<br />the structural plans and specifications contained
<br />within these
<br />drawings comply with the 2017 Florida Building Code -
<br />Residential 6th Edition. Engineers
<br />signature and seal is only for
<br />the structural engineering portions
<br />of the drawing pages bearing
<br />Engineer's signature and seal.
<br />,, 8
<br />� Co
<br />NW r-
<br />� N 3t
<br />0
<br />0
<br />Loo
<br />m nC'�
<br />�7 In � tOd
<br />bLL
<br />y�
<br />�ti a
<br />LLJ a
<br />LL
<br />Q
<br />NMM
<br />Co LLU-
<br />W rn
<br />LU
<br />° a X
<br />Z
<br />J -p �$Z
<br />mcv
<br />Z O
<br />0Xi-
<br />129
<br />'N
<br />mmo
<br />W
<br />W
<br />o - c-
<br />rn°'
<br /><C
<br />¢oa
<br />z
<br />ILW
<br />0
<br />LO N Cl) Z
<br />Q
<br />F J
<br />V OIL
<br />()t n
<br />N O)
<br />o g
<br />< v
<br />� o
<br />*1
<br />N
<br />M
<br />GN
<br />0 o
<br />4-,
<br />(D
<br />uJ
<br />W
<br />O-�
<br />w
<br />N
<br />�N
<br />C= N
<br />U)
<br />c�
<br />I
<br />8
<br />c "'
<br />QCD
<br />r,
<br />Vill
<br />M
<br />M
<br />z¢
<br />o
<br />Z
<br />a
<br />U_
<br />CE
<br />=o
<br />�Zo
<br />>o
<br />Cw�,o
<br />-n7
<br />OU
<br />F
<br />no
<br />OQE
<br />zo <
<br />aZoo
<br />�p
<br />z
<br />n0
<br />mo
<br />a,
<br />ZF
<br />J
<br />< w
<br />7 z
<br />N
<br />.�
<br />g g
<br />�
<br />5 o
<br />a
<br />U
<br />ao
<br />oLL
<br />ti�
<br />w
<br />��
<br />o
<br />Co
<br />d°T
<br />yM
<br />> d'
<br />W
<br />\
<br />m
<br />0
<br />"�
<br />c
<br />�
<br />CU
<br />M
<br />J
<br />�
<br />O
<br />U
<br />CO
<br />CD
<br />T
<br />tU NO
<br />.�
<br />= N
<br />ui
<br />M
<br />N
<br />co
<br />o
<br />Z
<br />Z
<br />E
<br />.
<br />'a
<br />Co
<br />_m
<br />tl
<br />E
<br />U J
<br />2
<br />a iIJ
<br />¢ p
<br />c
<br />0)
<br />JOB
<br />NO:
<br />20-8082
<br />SCALE :
<br />AS NOTED
<br />SHEET NO.
<br />W P
<br />
|