39795 Harmon Grove Ct - Laserfiche WebLink

Browse Search

SIMPSON HGAM10KTA W/ (4)1/4"x1 1/2" SDS SCREWS TO BLOCKING & (4) 1/4"X2 3/4" TITEN TO CMU 2x4 #2 SYP BLK'G @ 16" O.C. w/ (2)16d NAILS EA. END. SEE SCHEDULE - [RSH] - ON FRAMING SHEET FOR SHEATHING AND FASTENERS. (MIN. FIRST 4 BAYS) SEE STRUCTURAL NOTES AND NAILING TOENAIL w/ SCHEDULE FOR SHEATHING DETAIL-7 (2)16d NAILS 2x4 #2 SYP BLK'G @ 16" O.C. w/ (2)16d NAILS EA. END. SEE SCHEDULE - [RSH] - ON FRAMING SHEET FOR SHEATHING MAX. 9" AND FASTENERS. (MIN. FIRST 4 BAYS) UNSUPPORTED, IF >9" SEE 10/S5 BACKNAIL w/ (2)16d NAILS —� 2x4 #2 SYP BLK'G @ 16" O.C. w/ (2)16d NAILS EA. END. MAX. 9" SEE SCHEDULE - [RSH] - ON FRAMING SHEET FOR SHEATHING UNSUPPORTED, AND FASTENERS. (MIN. FIRST 4 BAYS) IF >9" SEE 10/S5 BACKNAIL w/ (2)16d NAILS SEE STRUCTURAL NOTES AND NAILING SCHEDULE FOR SHEATHING DETAIL I I 0 2" P T TE 45°t / 37 45° t SEE STRUCTURAL NOTES AND NAILING SCHEDULE FOR 2x4 CRO BRACE SHEATHING DETAIL 2x4 KICKER 2x8 SYP#2 "L" BRACE0 0 APPROX. 8" FROM @ 8'-0" O/C. EXTEND AT LEAST 90 /o OF RIDGE FASTENED AT "L" BRACE TO EXTEND 2x4 CROSS BRACE WEB LENGTH & NOTCH AT ' EACH JOINT W/ (3) 10d AT LEAST 90% OF WEB APPROX. 8" FROM BOTTOM CHORD (SEE TABLE) & (2)10d TOE NAILS @ LENGTH (SEE TABLE) RIDGE FASTENED AT EA. END @ 48" O.C. EACH JOINT w/ (3)10d & SIMPSON H2.5A w/ (10) 8d 2x8 P.T. GABLE TRUSS (2)10d TOE NAILS @ EA. FROM LEDGER TO • SILL 1/2"CDX PLYWOOD OR FATTACHEDW/10d ENDpy BLOCKING 7/16" OSB SHEATHING GYPSUM WALL BOARD �7 GABLE TRUSS NAILS @ 6" O.C. EDGES 2"x4" PANEL BLOCKING @ 48" O.C. FOR THE FIRST CDX PLYWOOD OR 7/16" ' AND 12" O.C. FIELD (4) ROWS OF TRUSSES FROM EA. END TYP. BOTTOM OSB SHEATHING ATTACHED OS 1 OdX3" @ 3" O/C CORD ATTACHED W/ (2) 16d TOENAILS w/ 1 Od NAILS @ 6" O.C. THROUGH CHORD 2"x4" LEDGER (MATCH BOTTOM CHORD EDGES AND 12" O.C. FIELD " SLOPE OF ADJACENT SCISSOR TRUSS) 2x4 #2 SYP BLK'G @ 16" O.C. w/ (2)16d NAILS EA. END. SEE SCHEDULE - [RSH] - ON FRAMING SHEET FOR SHEATHING AND FASTENERS. (MIN. FIRST BAYS) MAX. 9• BACKNAIL w/ (2)16d NAILS UNSUPPORTED, IF >9" SEE 1O/S5 SEE STRUCTURAL NOTES AND AI NAILING SCHEDULE FOR SHEATHINGDETAIL DOUBLE TOP PLATE 2"x4" CROSS BRACE 2x4 CROSS BRACE APPROX. 8" APPROX. 8" FROM FROM RIDGE FASTENED AT RIDGE FASTENED AT EACH JOINT w/ (3)1Od & (2)1Od EACH JOINT w/ (3) TOE NAILS @ EA. END 10d & (2)10d TOE NAILS @ EA. END 2x FRAME WALL (SEE WALL SECTION FOR SIZE & SPACING) 2x4 PANEL BLOCKING 1/2" CDX PLYWOOD OR 7/16" @ 48" O/C FOR THE OSB SHEATHING ATTACHED FIRST (4) ROWS OF W/ 10d NAILS @ 6" O.C. EDGES TRUSSES FROM EA. AND 12" O.C. FIELD END TYP. TOP & BOTTOM ATTACHED • (2) 16d NAILS W/ (2)16d TOENAILS NT x6 PLA 2x4 PANEL BLOCKING @ 48" O.C. FOR 2x BLOCKING 2x4 "T" ON TOP OF PANEL BLOCKING, 2"x6" P.T. SILL NOTCH "L" BRACE HERE WEEP SCREED „„ „ " THE FIRST (4) ROWS OF TRUSSES FASTEN WITH 10dx3 @ 4 O/C SPACED 2x4'7" ON TOP OF PANEL (2)16d NAILS INSTALLED PER MANUF. 1/2 x 8 J BOLT @ 48 O.C. WEEP SCREED FROM EA. END TYP. TOP &BOTTOM SIMPSON HGAI OKT w/ (4)1/4"x1 1/2" SDS SCREWS TO — @ 48" O.C. BLOCKING, FASTEN WITH SIMPSON META12 wl (7)10dxl 1/2" NAILS AT 6'-0" INSTALLED PER MANUF. ATTACHED w/ (2)16d TOENAILS TRUSS & (4)1/4"x3"SDS SCREWS TO PLATES AT 24" O.C. MOISTURE BARRIER 1Odx3" @ 4" O/C 1/2"x 8" "J" BOLT @ 32" O.C. MINIMUM 6" FROM O.C. MAX w/ MIN. 4" EMBEDMENT IN KO BLOCK - MOISTURE BARRIER PLATE SPLICES w/ 3/16"x2" 0 PLATE WASHER SIMPSON META12 w/ (7) ALTERNATE SIMPSON MSTAM24 w/ (7)10d NAILS NOTE: IF EMBEDDED 1Odx1 1/2" NAILS AT EA. & (4)1/4"x21/4'TITEN @ 4'-0" 0/C ALIGNED WITH STRAP MISSED VERTICAL SECTION 1 TRUSS VERTICAL WEB (24" GABLE WEB SECTION 2 WEB, USE MSTAM36 w/ (7) O.C. MAX) w/ MIN. 4 1Od NAILS & (4)1/4"X21/4" SCALE: N.T.S. S5 EMBEDMENT IN KO BLOCK SCALE: N.T.S. S5 TITEN ON OUTSIDE 2x4 #2 SYP BLK'G @ 16" O.C. w/ (2)16d NAILS EA. END. SEE SCHEDULE - [RSH] - ON FRAMING SHEET FOR SHEATHING -REFER TO DETAIL J tv N AND FASTENERS. (MIN. FIRST 4 BAYS) ON SHEET S5 FOR " SEE STRUCTURAL X-BRACING, AND TOP N NOTES AND NAILING CHORD BLOCKING `O � � SCHEDULE FOR INFORMATION SHEATHING DETAIL BACKNAIL w/ 1 1 (2)16d NAILS -WOOD TRUSSES �° 0o 0 2"x4"CROSS BRACE APPROX. 8" FROM -2x4 RAT RUN BRACING RIDGE FASTENED AT AT 24" O.C. ON TOP OF EACH JOINT w/ (3) • BOTT. CHORD FOR 4 TRUSS SPANS 10d & (2)10d TOE NAILS @ EA. END ATTACHED W/ 2 -16d AT EA. TRUSS JOINT (2) 2" x 4" LAMINATIONS W/ (1) ROW (3) 2" x 4" LAMINATIONS W/ (1) ROW (3) 2" x 6" LAMINATIONS W/ (2) ROWS OF 2x4 PANEL BLOCKING FI 48" FOR THE (2) 16d NAILS - OF STAGGERED 10d COMMON WIRE NAILS OF STAGGERED 30d COMMON WIRE NAILS STAGGERED 30d COMMON WIRE NAILS FIRST (4) ROWS OF (4) 2x4 BLOCKING @ 24" (D = 0.148", L = 3") OR EQUAL (D = 0.207", L = 41/2") OR EQUAL (D = 0.207", L = 41/2") OR EQUAL O/C w/ (2)16d TRUSSES FROM EA. TOENAILS @ EA. END NOTES: END TYP. TOP & 1) ADJACENT NAILS ARE DRIVEN FROM OPPOSITE SIDES 4) FOR 4-PLY, PROVIDE 1/4" DIA. x 51/2" LAG SCREWS OR EQUAL BOTTOM ATTACHED - MASONRY WALL OF THE COLUMN (SPACE AS SHOWN FOR 3-PLY) W/ (2)16d TOENAILS -ARCHITECTURAL FINISH 2) ALL NAILS PENETRATE AT LEAST 3/4 OF THE THICKNESS 5) FOR 5-PLY, PROVIDE 1/4" DIA. x 7" LAG SCREWS OR EQUAL SPACE AS SHOWN FOR 3 PLY) MAX. 9" UNSUPPORTED, IF >9" SEE 1 O/S5 "L" BRACE TO EXTEND AT LEAST 90% OF WEB LENGTH (SEE TABLE) -GABLE TRUSS -1/2" CDX PLYWOOD OR 7/16" OSB SHEATHING ATTACHED w/ 1Od NAILS @ 6" O.C. EDGES AND 12" O.C. FIELD -2x4'T' ON TOP OF PANEL BLOCKING, FASTEN WITH 1Odx3" @ 4" O/C 2x4 BLOCKING 2x4'T' BLOCKING @ 48" O.C. 16d NAIL "L" BRACE ATTACHED W/ 1 Od NAILS @ 4" O.C. TYPICAL GABLE TRUSS WEB DOUBLE "L" BRACING DETAIL 5 SCALE: N.T.S. S5 2x4' " BLOCKING 2x4 BLOCKING @ 48" O.C. "L" BRACE ATTACHED 16d NAIL W/ 1 Od NAILS @ 4" O.C. TYPICAL R__1q GABLE TRUSS WEB J SINGLE "L" BRACING DETAIL 6 SCALE: N.T.S. S5 DIAPHRAGM BLOCKING @ 48"O/C GABLE TRUSS TRUSS VERTICAL SIMPSON SP2 w/ (12)10d 2x4 LEDGER (MATCH BOTTOM CHORD DBL. TOP PLATE NAILS AT EACH STUD (2) 2"x8" "L" BRACE SLOPE OF ADJACENT TRUSS) STUD WALL (SEE TYP. SEC.) FASTENED WITH (3) SECTION 3 SECTION 4 16d PER SIDE SCISSOR GABLE 'IT" BRACE 7 SCALE: N.T.S. S5 SCALE: N.T.S. S5 AS PER H►B 91 SCALE: N.T.S. S5 MAX. 9" UNSUPPORTED, IF >9" SEE 10/85 "L" BRACE TO EXTEND AT LEAST 90% OF WEB LENGTH (SEE TABLE) -GABLE TRUSS -1/2" CDX PLYWOOD OR 7/16" OSB SHEATHING ATTACHED W/ 10d NAILS @ 6" O.C. E ES AND 12" O.C. FIELD /�JACK TRUSS / SEE PLAN FOR EXT. WALL CONN. NON - LOAD BEARING LOCATION D OF THE LAST LAMINATION ( - 3) EACH 30d COMMON NAIL MAY BE REPLACED W/ (2)16d 6) REFER TO NDS SECTION 15.3 FOR ADDITIONAL INFORMATION COMMON NAILS. (ONE INTO EACH OUTSIDE FACE OF B.U.C., SAME NUMBER OF ROWS, SAME SPACING)SECTION TYPICAL NAILING SCHEDULES FOR BUILT-UP COLUMNS r8%� 2x4 "T" ON TOP OF PANEL BLOCKING, FASTEN WITH L 2x4 BLOCKING W/ 10dx3" @ 4" O/C (2)12d TOENAILS g - SCALE: N.T.S. S5 SEE TYP. WALL SECTION FOR SCALE: 3/4"= V-0" S5 ADDITIONAL INFORMATION. SCALE: N.T.S. S5 IINIMUM 2x ;ROSS BRACING 3EE PLAN FOR OCATIONS) TOENAIL (2)16d NA (2)16d PER JOINT L CONTINUOUS BOTTOM CORD BRACING 2"x4" MIN. SEE M/S5 CROSS BRACING DETAIL J SCALE: N.T.S. S5 12" SH SCHEDULE ,TTACHMENT ? SYP BLK'G @ 16" O.C. I x 0.131" AILS EA. SIDE 2x4 #2 SYP w/ 1 Od XO.131" @ 8" O.C. ALTERNATE NON -DROP GABLE END DETAIL 10 SCALE: N.T.S. S5 1 GABLE TRUSS S5 "L" BRACE W/ 10d @ 4" O.C. 12 (SEE SCHEDULE FOR SIZE AND LOCATION) 6.9 MAX. S5 GABLE END BRACING DETAIL CONT. BEARING MEAN WALL HEIGHT UP TO 30'-0" - SEE STRUCTURAL NOTES FOR WIND SPEED SPECIFICATION SCALE: N.T.S. PRE-ENGINEERED WOOD TRUSSES OVERLAP TRUSS BRACING AT LEAST TWO TRUSS SPACES '-MINIMUM (2)16d PER JOINT \-MINIMUM 2X4 TRUSS BRACING TRUSS BRACING OVERLAP DETAIL SCALE: N.T.S. 6" OVERLAP M S5 "L" BRACE W/ 10d @ 4" O/C (SEE SCHEDULE FOR SIZE AND LOCATION) a 8d @ 6"O/C WOOD TRUSSES SIMPSON HGAMI OKTA w/ (4) 1/4"xi 1/2" SDS SCREWS TO BLOCKING & (4)1/4"X2 3/4" TITEN TO CMU 2 x 4 BLOCKING w/ (2)1Od TOE NAILS AT EACH END @ 24" O/C (TYP) • 0 w `BRACING w/ (3)10d x 3" AT EACH CONN. @ 24" O/C `MOISTURE BARRIER -BOND BEAM MASONRY WALL ARCHITECTURAL FINISH EXT. WALL CONN. @ NON - LOAD BEARING LOCATION (UNEVEN CLG.) rE SEE TYP. WALL SECTION FOR SCALE: N.T.S. S5 ADDITIONAL INFORMATION. "L" BRACING REQUIREMENTS STUD SPACING NO "L" BRACE (1) 2"x4" (U.N.O.) "L" BRACE 2"X6" (U.N.O.) "L" BRACE 24" 010" - Y-ON T-0" - 6'-0" 6'-0" & GREATER SCISSOR GABLE - (1) 2"x8" #2 S.P.F. @ EACH VERTICAL AND (2) 2"x8" FULL HEIGHT @ DIAPHRAGM BLOCKING NOTE: 1) "L" BRACE MUST EXTEND AT LEAST 90% OF WEB LENGTH EXCEPT, SCISSOR GABLE WHICH REQUIRES BRACE TO EXTEND FULL HEIGHT OF GABLE. 2) "L" BRACE TO BE FASTENED TO GABLE STUD WITH 1Odx3" NAILS @ 4" 0/C. 3) SEE 6/S5 FOR MORE INFO. SIMPSON HGA10KT wl (4) 1/4"xl 1/2" SDS SCREWS TO TRUSS & (4)1/4"x3" SDS SCREWS TO PLATES (TYP.) \—STUDS @ 16" O.C. GABLE END BRACING DETAIL SCALE:3/4"=1'-0" MEAN WALL HEIGHT UP TO 30'-0" - SEE STRUCTURAL NOTES FOR WIND SPEED SPECIFICATION TRUSS SIMPSON SP2 w/ (12) 10d NAILS AT EACH STUD END JACK 1 V-0" MAX. 9c4^ LU CORNERJACK C7 Y a v W Z Cr 0 HIP FRAMING REFERENCE PLAN 20'-0" MAX 20'-0" MAX 'W BRACE SEE DET. J/S5 n CONTINUOUS BOTTO CHORD BRACING 2X4 MIN. L9 q M i s a epp NOTE: ZTOP CHORD 2x4 #2 SYP BRACING 1) SEE TRUSS MANUFACTURER'S TRUSS ENGINEERING @ 16" O.C. MAX. FOR FIRST (4) CUT SHEETS FOR ADDITIONAL PERMANENT BRACING BAYS THAT MY BE REQUIRED BOTTOM CHORD GABLE END BRACING 2)'7" BRACING MAY BE USED IN PLACE OF PERMANENT @ 4'-0" O.C. MAX. FOR FIRST (4) BAYS BRACING PROVIDED IT EXTENDS OVER AT LEAST 90% OF THE WEB. REQUIRED MINIMUM PERMANENT TRUSS BRACING PLAN AS PER BCSI SCISSOR TRUSS SCISSOR TRUSS WI DROP CEILING BRACING DETAIL SCALE: N.T.S. 2X4 BRACING @ 48" O.C. CONTINUOUS TO FIXED LOCATION ATTACHED W/ (2)10d AT EA. TRUSS (NOTE: BRACING MAY BE PLACED ON EITHER TOP OR BOTTOM OF THE BOTTOM CORD) COSMETIC DROP CEILING FRAMING MEAN ROOF HEIGHT UP TO 30'-0" SCALE: NTS SEE STRUCTURAL NOTES FOR WIND SPEED SPECIFICATION WOOD FRAMED GABLE END BRACING DETAIL MEAN WALL HEIGHT UP TO 30'-0" - SEE STRUCTURAL NOTES SCALE: N.T.S. FOR WIND SPEED SPECIFICATION lkf �ggq11i1t11IIINf/,� N SE r. : �� 6N _ � Q U CEO .�4C. r O OF {�lllltltll To the best of the Engineers knowledge, Information and belief, the structural plans and specifications contained within these drawings comply with the 2020 Florida Building Code - Resldents] 7th Edition. Engineers signature and seal is only for the structural engineering portions of the drawing pages bearing Engineer's signature and seal. 0 H E j o �g F# CFI(a a ri a)NoZR LL a yMv 9'I*,U_LL � a � 05 J o Z _9°$$'° pNcomOWm W W��pjO' Q Q "1 LL a N MZ a: L) z W ❑DO 0 Z � M Z Z n N CD Ora U Q) � 0 In w cA =Das 1 _ Of =I�' o w o ao z LJL E E E >� z 9 U C n U �� � � wU o� N r0 $ w z co m� 0 zW aw W J � ,z <tl $ iZ U a N 1 �_ co w �5 O > Ln (W c�L1 D i` •�y U L O IJ- a) p N m 0 CD T V E N a T N x �LO L0 ai m EE O M rn o Z E c a v 1 . :2o JOB NO: 20-8092 SCALE : AS NOTED SHEET NO. S5