39846 Harmon Grove Ct - Laserfiche WebLink

Browse Search

�UWIYaI�illy I:_1 111. _ AM 4' OFFRIDGE VENT"" 4' OFFRIDGE VEN 12 12 T _. l-_�y�.�-L,,,,�ter.. ��I- '= `-•-�'_- - - 3 TAB SHINGLES. ROOF INSTALLED AS PER MANUF. SPECIFICATIONS EXTENDED OVERHANG TO BE CENTERED ON DOOR TEXTURED CEMENTITIOUS FINISH ON C.M.U. (TYP.) T.O.M. - — -T HDR HGT. TEXTURED CEMENTITIOUS 4 co FINISH ON C.M.U. (TYP.) --------- T.O.M. 1'-0" HDRI ---------- F.FL. REAR ELEVATION - B1 ------------------------------------------------------- 1'-0" TEXTURED CEMENTITIOUS FINISH ON C.M.U. (TYP.) 3'-0" F. FL. NONE RIGHT ELEVATION - B1 General Notes ROOF CRITERIA: • 12" OVERHANG U.N.O. • PLUMB CUT FASCIA ROOF • PITCH PER ELEVATION **G.C. VERIFY ROOF PITCH'"* ROOF PITCH VARIES PER SUBDIVISIONS IT IS THE CONTRACTORS RESPONSIBILITY TO VERIFY ROOF SLOPE REQUIREMENTS WITH TRUSS MANUFACTURER. **ELECTRICAL SPECIFICATION NOTES** ELECTRICAL CONTRACTOR MUST VERIFY WITH THE SPECIFICATIONS FOR THE TYPE OF FIXTURE TO BE USED. LIGHT FIXTURES SHOWN ARE FOR LOCATION PURPOSES. Exterior Covering R703.7 Exterior Plaster. Installation of these materials shall be in compliance with ASTM C926 and ASTM C1063, or ASTM C1787 and the provisions of this code. R703.7.1 Lath. Lath and Lath attachments shall be of corrosion -resistant materials. Expanded metal or woven wire lath shall be attached with 1-1/2" long, 11 gage nails having a 7/16" head, or 1-1/2" long, 16 gage staples, spaced in accordance with ASTM C1063 or C1787, or as otherwise approved. R703.7.2 Plaster. Plastering with cement plaster shall be not less than three coats where applied over any type of code -approved lath and shall be not less than two coats where directly applied over masonry, concrete, clay brick, stone, or tile. If the plaster surface is completely covered by veneer or other facing material or is completely concealed, plaster application need be only two coats, provided total thickness is as set in Table R702.1(1). Cement plaster shall be in accordance with ASTM C926 and material shall be in accordance with one of the types listed in R703.7.2. R703.7.3 Water -Resistive Barriers. Water -resistive barriers shall be installed as required in Section R703.2 and, where applied over wood -based sheathing, shall include a water -resistive vapor -permeable barrier with a performance at least equivalent to two layers of Grade D paper. The individual layers shall be installed independently such that each layer provides a separate continuous plane and any flashing (installed in accordance with Section R703.4) intended to drain to the water -resistive barrier is directed between the layers. R703.2 Water -Resistive Barrier. One layer of No. 15 asphalt felt, free from holes and breaks, complying with ASTM D226 for Type 1 felt or other approved water -resistive barrier shall be applied over studs or sheathing of all exterior walls. No. 15 asphalt felt shall be applied horizontally, with the upper layer lapped over the lower layer not less than 2 inches. Where joints occur, felt shall be lapped not less than 6 inches. Other approved materials shall be installed in accordance with the water -resistive barrier manufacturer's installation instructions. The No. 15 asphalt felt or other approved water -resistive barrier material shall be continuous to the top of walls and terminated at penetrations and building appendages in a manner to meet the requirements of the exterior wall envelope as described in Section R703.1. R703.4 Flashing. Approved metal flashing, vinyl flashing, self -adhered membranes and mechanically attached flexible flashing shall be applied shingle -fashion or in accordance with the manufacturer's instructions. Metal flashing shall be corrosion resistant. Fluid -applied membranes used as flashing shall be applied in accordance with the manufacturer's instructions. All flashing shall be applied in a manner to prevent the entry of water into the wall cavity or penetration of water to the building structural framing components. Self -adhered membranes used as flashing shall comply with AAMA 711. All exterior fenestration products shall be sealed at the juncture with the building wall with a sealant complying with AAMA 800 or ASTM C920 Class 25 Grade NS or greater for proper joint expansion and contraction, ASTM C1281, AAMA 812, or other approved standard as appropriate for the type of sealant. Fluid -applied membranes used as flashing in exterior walls shall comply with AAMA 714. The flashing shall extend to the surface of the exterior wall finish. Approved flashings shall be installed at the following locations. • Exterior window/door openings. • Intersection of chimneys or other masonry construction with frame walls. • Under and at the ends of masonry, wood or metal copings and sills. • Continuously above all projecting wood trim. • Where exterior porches, decks or stairs attach to a wall or floor assembly of wood -frame construction. • At wall and roof intersection. • At Built-in gutters. Coastal Flashings All flashing material for coastal locations (ex: within 3,000 feet of the ocean) shall be corrosion resistant material (ex: zinc and/or stainless steel) and shall be selected for compatibility with adjacent wood preservatives per the manufacturer's recommendations. f W P•'•• SE •' Y Gi� To the best of the Engineers knowledge, information and belief, the structural plans and specifications contained within these drawings comply with the 2020 noflda Building code - Residentlal 7th Edition. Engineers signature and seal Is only for the structural engineering portions of the drawing pages bearing Engineers signature and seal. O N 04 LL J it u w J LL LL o Z _ W,Z)Q 0 J f0 m °' d a ILW 0 a rvNj Z tJ O N U N = OU ❑ ❑ ❑ V z z z J G (1) V' • cn LL Lu o 1'�• J OW to c d U c • o w (�E o0gq¢0, a E Q Q W U Z g M Z U N J Q Z a N W T � U $E No � ~� g o �C:) J B L it > U Oi � O T m O 04 c�t7 CD Lo 2 N 04 T— t i � T T M o Z Z E � I]- U Q p J JOB NO: 21-1070 SCALE : AS NOTED SHEET NO. 3.2