Laserfiche WebLink
Co <br />d <br />iu <br />x <br />rn <br />0 <br />0 <br />12 <br />- <br />`� ■■ MENNEN <br />■ ■ ■ ■ ■ ■ ■ ■ 1' — - • <br />FINISH ON <br />000a0000 ■•- .- <br />nr� nrn nnnn - <br />14'-0" RIDGE VENT <br />12 <br />5� <br />FRONT ELEVATION - Al <br />SCALE: 1 /4"=V-0" <br />12 <br />__115 15'-0" RIDGE VENT <br />0 <br />;t <br />N <br />3 TAB SHINGLES. ROOF <br />INSTALLED AS PER <br />MANUR SPECIFICATIONS <br />T.O.M. <br />---------------- HDRHGT. <br />IT-0 <br />TEXTURED TEXTURED - <br />CEMENTICIOUS CEMENTICIOUS co <br />FINISH ON C.M.U. FINISH ON C.M.U. ip <br />(TYP.) (TYP.) <br />----------------------F.FL. • <br />LEFT ELEVATION <br />- Al <br />1 /4"=1'-0" <br />N <br />General Notes <br />ROOF CRITERIA: <br />• 12" OVERHANG U.N.O. <br />• PLUMB CUT FASCIA ROOF <br />• PITCH PER ELEVATION <br />**G.C. VERIFY ROOF PITCH** <br />ROOF PITCH VARIES PER SUBDIVISIONS IT IS THE <br />CONTRACTORS RESPONSIBILITY TO VERIFY <br />ROOF SLOPE REQUIREMENTS WITH TRUSS <br />MANUFACTURER. <br />**ELECTRICAL SPECIFICATION NOTES** <br />ELECTRICAL CONTRACTOR MUST VERIFY WITH <br />THE SPECIFICATIONS FOR THE TYPE OF FIXTURE <br />TO BE USED. LIGHT FIXTURES SHOWN ARE FOR <br />LOCATION PURPOSES. <br />Exterior Covering <br />R703.7 Exterior Plaster. <br />Installation of these materials shall be in compliance with ASTM <br />C926 and ASTM C1063, or ASTM C1787 and the provisions of <br />this code. <br />R703.7.1 Lath. <br />Lath and Lath attachments shall be of corrosion -resistant <br />materials. Expanded metal or woven wire lath shall be attached <br />with 1-1/2" long, 11 gage nails having <br />a 7/16" head, or 1-1/2" long, 16 gage staples, spaced in <br />accordance with ASTM C1063 or C1787, or as otherwise <br />approved. <br />R703.7.2 Plaster. <br />Plastering with cement plaster shall be not less than three coats <br />where applied over any type of code -approved lath and shall be <br />not less than two coats where directly applied over masonry, <br />concrete, clay brick, stone, or tile. If the plaster surface is <br />completely covered by veneer or other facing material or is <br />completely concealed, plaster application need be only two coats, <br />provided total thickness is as set in Table R702.1(1). <br />Cement plaster shall be in accordance with ASTM C926 and <br />material shall be in accordance with one of the types listed in <br />R703.7.2. <br />R703.7.3 Water -Resistive Barriers. <br />Water -resistive barriers shall be installed as required in Section <br />R703.2 and, where applied over wood -based sheathing, shall <br />include a water -resistive vapor -permeable barrier with a <br />performance at least equivalent to two layers of Grade D paper. <br />The individual layers shall be installed independently such that <br />each layer provides a separate continuous plane and any flashing <br />(installed in accordance with Section R703.4) intended to drain to <br />the water -resistive barrier is directed between the layers. <br />R703.2 Water -Resistive Barrier. <br />One layer of No. 15 asphalt felt, free from holes and breaks, <br />complying with ASTM D226 for Type 1 felt or other approved <br />water -resistive barrier shall be applied over studs or sheathing of <br />all exterior walls. No. 15 asphalt felt shall be applied horizontally, <br />with the upper layer lapped over the lower layer not less than 2 <br />inches. Where joints occur, felt shall be lapped not less than 6 <br />inches. Other approved materials shall be installed in accordance <br />with the water -resistive barrier manufacturer's installation <br />instructions. The No. 15 asphalt felt or other approved <br />water -resistive barrier material shall be continuous to the top of <br />walls and terminated at penetrations and building appendages in <br />a manner to meet the requirements of the exterior wall envelope <br />as described in Section R703.1. <br />R703.4 Flashing. <br />Approved metal flashing, vinyl flashing, self -adhered membranes <br />and mechanically attached flexible flashing shall be applied <br />shingle -fashion or in accordance with the manufacturer's <br />instructions. Metal flashing shall be corrosion resistant. <br />Fluid -applied membranes used as flashing shall be applied in <br />accordance with the manufacturer's instructions. All flashing shall <br />be applied in a manner to prevent the entry of water into the wall <br />cavity or penetration of water to the building structural framing <br />components. <br />Self -adhered membranes used as flashing shall comply with <br />AAMA 711. All exterior fenestration products shall be sealed at <br />the juncture with the building wall with a sealant complying with <br />AAMA 800 or ASTM C920 Class 25 Grade NS or greater for <br />proper joint expansion and contraction, ASTM C1281, AAMA 812, <br />or other approved standard as appropriate for the type of sealant. <br />Fluid -applied membranes used as flashing in exterior walls shall <br />comply with AAMA 714. The flashing shall extend to the surface <br />of the exterior wall finish. <br />Approved flashings shall be installed at the following locations. <br />• Exterior window/door openings. <br />• Intersection of chimneys or other masonry construction with <br />frame walls. <br />• Under and at the ends of masonry, wood or metal copings <br />and sills. <br />• Continuously above all projecting wood trim. <br />• Where exterior porches, decks or stairs attach to a wall or <br />floor assembly of wood -frame construction. <br />• At wall and roof intersection. <br />• At Built-in gutters. <br />Coastal Flashings <br />All flashing material for coastal locations (ex: within 3,000 feet of the <br />ocean) shall be corrosion resistant material (ex: zinc and/or stainless <br />steel) and shall be selected for compatibility with adjacent wood <br />preservatives per the manufacturer's recommendations. <br />Q G� > <br />W <br />LM <br />FLO <br />��j✓�,R0rE <br />SS10N�\\\\ <br />To the best of the Engineer's knowledge, information and belief, <br />the structural plans and specifications contained within these <br />drawings comply with the 2020 <br />Florida Building Code - <br />Residential 7th Edition. Engineer's signature and seal is only for <br />the structural engineering portions of the drawing pages bearing <br />Engineer's signature and seal. <br />W <br />Q <br />apM� E <br />N J <br />0 <br />N {{pp <br />N 6 <br />rn eo <br />a <br />� U. u-a w 5c <br />0 <br />0 <br />Z <br />t m ; of 5 <br />Wco <br />m N W O <br />��O'O' co Q <br />IL. <br />a MZQ'y0 <br />V rVn <br />ZOU <br />W <br />❑ ❑ ❑ <br />Ur <br />z_ t <br />z <br />Z <br />J <br />tv <br />z <br />Ur <br />w W <br />G>Ln <br />O <br />W 8 <br />YZCA <br />M <br />c y <br />a® <br />_ <br />_ <br />74 <br />w <br />M <br />° <br />Z' <br />rJ, <br />s; <br />- <br />> - <br />'aR <br />=_® <br />Q <br />o <br />E <br />E U <br />- <br />'0 <br />QQ <br />° <br />oa <br />00 <br />� <br />° <br />Z <br />O E <br />iCD <br />04 03 <br />�O <br />ao <br />o <br />d2% <br />rr� <br />'0 <br />• r0 <br />' o <br />�Z <br />ZCO <br />0) <br />J <br />Fw <br />° <br />a w <br />s <br />Z z <br />i�o <br />2.ao <br />=m <br />rg- <br />J <br />o <br />o <br />w <br />o <br />0. <br />co <br />YN 0 <br />3 <br />O <br />i <br />j L6 <br />W <br />C9 <br />.> <br />00 <br />U <br />� <br />Q <br />U <br />> <br />p <br />T <br />L <br />T— <br />70 <br />ca r <br />= <br />Q� <br />N <br />00O <br />T­ <br />Lo <br />i 00 <br />00 CID <br />T <br />cc <br />T <br />coN <br />r <br />o <br />Z <br />Z <br />Q <br />E <br />a <br />U � <br />Q a <br />� <br />JOB <br />NO: <br />21-1071 <br />SCALE : <br />AS NOTED <br />SHEET NO. <br />3.1 <br />