Laserfiche WebLink
3 TAB SHINGLES. ROOF <br />INSTALLED AS PER MANUF. <br />SPECIFICATIONS <br />--------------------- <br />TEXTURED <br />CEMENTICIOUS <br />FINISH ON C.M.U. <br />(TYP. ) <br />12 <br />5� <br />3 TAB SHINGLES. ROOF <br />INSTALLED AS PER <br />MANUF. SPECIFICATIONS <br />12 <br />5� <br />— — — — — EXTSNDE-l— --� <br />OVERHANG TO BE <br />CENTERED ON DOOR <br />12 <br />�5 <br />T.O.M. <br />—�------- <br />1t0 <br />ZC�------- HDRHGT <br />----------------------------------- F.FL. <br />12 <br />�5 <br />19' RIDGE VENT <br />0 <br />ED <br />4 <br />F_ <br />REAR ELEVATION — Al <br />T.O. <br />TEXTURED TEXTURED <br />CEMENTICIOUS CEMENTICIOUS <br />2'-0" FINISH ON C.M.U. FINISH ON C.M.U. <br />(TYP.) (TYP.) <br />BO <br />-------------- F.FL. <br />LEFT ELEVATION — Al <br />1/4"= <br />General Notes <br />ROOF CRITERIA: <br />• 12" OVERHANG U.N.O. <br />• PLUMB CUT FASCIA ROOF <br />• PITCH PER ELEVATION <br />**G.C. VERIFY ROOF PITCH** <br />ROOF PITCH VARIES PER SUBDIVISIONS IT IS THE <br />CONTRACTORS RESPONSIBILITY TO VERIFY <br />ROOF SLOPE REQUIREMENTS WITH TRUSS <br />MANUFACTURER. <br />**ELECTRICAL SPECIFICATION NOTES** <br />ELECTRICAL CONTRACTOR MUST VERIFY WITH <br />THE SPECIFICATIONS FOR THE TYPE OF FIXTURE <br />TO BE USED. LIGHT FIXTURES SHOWN ARE FOR <br />LOCATION PURPOSES. <br />Exterior Covering <br />R703.7 Exterior plaster. <br />Installation of these materials shall be in compliance with ASTM C <br />926 and ASTM C 1063. <br />R703.7.1 Lath. <br />All Lath and lath attachments shall be of corrosion -resistant <br />materials. Attached per ASTM C 1063. <br />R703.7.2 Plaster. <br />Plastering w/ portland cement plaster shall be not less than three <br />coats when applied over metal lath or wire lath and shall be not <br />less than two coats when applied over masonry, concrete. <br />R703.7.3 Water -Resistive Barriers. <br />Water -resistive barriers shall be installed where cement plaster <br />(stucco) is to be applied over wood -based sheathing, shall include <br />a water -resistive vapor -permeable barrier. The individual layers <br />shall be installed independently such that each layer provides a <br />separate continuous plane and any flashing intended to drain to <br />the water -resistive barrier is directed between the layers. The <br />barriers shall consist of one of the following. <br />1. Two layers of an approved water resistant barrier material in <br />accordance with R703.2. <br />2. One layer of an approved water -resistive barrier (paper <br />backed stucco lath) over an approved synthetic house wrap. <br />R703.4 Flashing. <br />Approved corrosion -resistant flashing shall be applied <br />shingle -fashion in a manner to prevent entry of water into the wall <br />cavity or penetration of water to the building structural framing <br />components. Flashing shall be installed at the following locations. <br />• Exterior window/door openings. <br />• Intersection of chimneys or other masonry constructions with <br />frame walls. <br />• Under and at the ends of masonry, wood or metal copings <br />and sills. <br />• Continuously above all projecting wood trim. <br />• Where exterior porches, decks or stairs attach to a wall or <br />floor assembly of wood -frame construction. <br />• At wall and roof intersections <br />• At Built-in gutters. <br />Attic Ventilation <br />Attic Ventilation to be in compliance with the Florida Building Code 6th Edition <br />(2017) Residential R806. <br />The Minimum net free ventilating area shall be 1/150 of the area of the vented <br />space. The ventilating area may be reduced to 1/300 provided that at least 40% <br />but no more than 50% of the required ventilation is provided in the upper portion of <br />the space to be ventilated.Upper ventilators shall be located no more than 3 feet <br />(measured vertically) below the ridge or highest point of the space, with the <br />balance of the required ventilation provided by eave or cornice vents. <br />"CALCULATIONS BASED ON THE FOLLOWNG VALUES, SEE ROOF PLAN"' <br />(Values to be verified with Manufacturer Specifications) <br />• RIDGE VENTS 15 SO. IN. OF NET FREE AREA / LINEAR FT. <br />• OFF -RIDGE VENTS 138 SO. IN. OF NET FREE AREA / UNIT <br />• SOFFIT VENTS 7 SQ. IN. OF NET FREE AREA / SQ. FT. <br />a <br />0 0 <br />0 <br />0 <br />o <br />z <br />z <br />a 8 <br />N c9 <br />U <br />0 w <br />V1 <br />Ln <br />C_U m <br />/Z <br />N A <br />LY <br />�W U< <br />Q ' 0. <br />lo���\\�� <br />To the hest of the Engineers knowledge, information and belief, <br />the structural plans and specifications contained within these <br />drawings comply with the 2017 Florida Building Code - <br />Residential 8th Edition. Engineer's signature and seal is only for <br />the structural engineering portions of the drawing pages bearing <br />Engineer's signature and seal. <br />�p <br />M <br />w <br />Q <br />E <br />E <br />N <br />zW�� <br />a ff <br />ZZQo <br />6 N <br />30 <br />z <br />H� <br />� M <br />a. <br />aa62 <br />U <br />z <br />2 <br />LE <br />r <br />o <br />aGo <br />C� <br />m0 <br />z <br />(n C <br />N J <br />VY <br />m 0 <br />Zz <br />wm <br />8� <br />i y <br />�o <br />W <br />� <br />a <br />U <br />;LL <br />a <br />mw <br />_ <br />�K <br />Milli <br />"� <br />k�� <br />0 <br />�Io <br />L= <br />r <br />sY' <br />il�d <br />L) 3 <br />c 0 <br />B <br />>M <br />L <br />' j <br />T <br />0 <br />ool1 <br />U) <br />0 <br />C m� <br />N <br />~ <br />c <br />go 3 <br />7- <br />U) <br />tv <br />0 v_ <br />LO <br />T <br />CN <br />T CID <br />0000 N <br />T <br />6 <br />T M (M <br />' O ^ <br />c <br />Z <br />z <br />a <br />E <br />0 Q p <br />JOB <br />NO : 19-5898 <br />SCALE : AS NOTED <br />SHEET NO. <br />3.2 <br />