Laserfiche WebLink
I:Alhi <br />OICADETM <br />MCADETM <br />BARRICADETM BARRICAPIfim BARRICADETM <br />Fold the three flaps in through the opening, <br />fastening them inside with staples set about <br />every 6". Fold top flap up and tape temporarily <br />as shown. <br />Other Important Details: <br />• Install building wrap "shingle -lap" fashion <br />(with the higher piece lapped over the <br />outside of the piece below). <br />• All horizontal overlaps of building wrap <br />should be at least 4" and vertical overlaps <br />should at least be 6". <br />WRB INSTALLATION. <br />SCALE: N.T.S. <br />sheathing or exterior gypsum board. <br />BARRICADETM <br />BARRICADETM <br />BARRICADETM <br />BARRICADETM <br />y <br />RRICADETM BARRICADETM BARRICADETM <br />Install the bottom flashing over the wrap. <br />Note: Barricade Building Products recommends <br />the use of flashing material, such as OptiFlash® <br />or Contour® premium butyl rubber flashing, that <br />meets or exceeds Federal Specification <br />UU-B-790a, Grade A and is minimum 6" in <br />width. <br />• At roof sections, be careful to lap the <br />building wrap over the entire top of any step <br />flashed areas against the wall. <br />• Around exterior doors, follow the same <br />flashing procedures as indicated in steps 5 <br />and 6 for windows. <br />BARRICADETM <br />BARRICADETM <br />BARRICADETM <br />Flashing details around window: <br />A' Install side flashing over side window flanges. <br />g Install head flashing over the top window <br />flange and extend it out 3"-4" over the side <br />flashings. <br />C Bottom window flange should be over <br />flashing, installed in Step 5. <br />D Remove temporary tape from top building <br />wrap flap and apply over installed head <br />flashing. <br />Note: Windows must be installed in <br />accordance with manufacturer's <br />recommended installation procedures. <br />NOTE: FLASHING AT EXTERIOR WINDOW AND <br />DOOR OPENINGS SHALL BE INSTALLED IN <br />ACCORDANCE WITH FMA/AAMA 100, FMA/AAMA <br />200, FMA/WDMA 250, FMA/AAMA/WDMA 300 OR <br />FMA/AAMA/WDMA 400 AS PER R703.4.1.4 <br />(2020 FBC-RESIDENTIAL, 7TH EDITION) <br />e <br />SEAL EDGE OF P.T. WOOD <br />BUCK TO MASONRY <br />EXTERIOR CMU WALL <br />1) PROTECTO WRAP LWM200 OR <br />SIMILAR ON WINDOW SILL, JAMBS <br />AND HEAD. APPLY AROUND <br />CORNER AND EXTEND 6" ALL <br />AROUND THE EDGES OF THE WALL <br />PRECAST SILL <br />2) SET P.T. WOOD BUCK <br />OVER CMU <br />WATERPROOFING IN <br />URETHANE SEALANT. <br />FASTEN PER PRODUCT <br />APPROVALS. <br />3) APPLY LIQUID <br />WATERPROOFING <br />MEMBRANE OVER THE TOP <br />AND EXTERIOR FACE OF <br />BUCK AND SILL <br />4) INSTALL WINDOW <br />OR DOOR. FASTEN PER <br />PRODUCT APPROVALS <br />AND SEAL WINDOW OR <br />DOOR FRAME TO P.T. <br />WOOD BUCK AND <br />MASONRY <br />CMU OPENING WATERPROOFING <br />SCALE: N.T.S. <br />BARRICADETM <br />• Barricade Flash Right <br />SBS Window & Door <br />Flashing Tape <br />• Barricade Sill Corners <br />• Barricade Conform <br />Stretchable Flashing <br />WOOD OPENING WATERPROOFING <br />rr <br />W <br />�_rr <br />�00� <br />>CWC40 <br />W:D0I— <br />¢D�- <br />_a. � � J <br />Y Q H Z <br />L_00(1) <br />ZZZI'z <br />J Q 2 J <br />Wa=cr2= <br />�c)000 <br />=ZLLcn <br />¢?o <br />� o <br />O N <br />Z <br />(n <br />Q <br />� <br />O <br />w <br />u <br />A <br />O <br />Z <br />0 <br />O <br />I--" <br />O <br />O <br />U) <br />w <br />w <br />w <br />I..r <br />o <br />x <br />z <br />0 <br />R <br />It <br />U) <br />W <br />0 <br />t� <br />O <br />4 <br />c� <br />CKZ <br />aaaaa <br />�a JAN 18 2022 <br />COMMUNITY: <br />LINKS AT CALUSA <br />SPRINGS <br />PLAN # 6103 <br />RELEASED: 1/18/22 <br />SHEET <br />WP2 <br />SCALE: N.T.S. <br />