|
IF NECESSARY,
<br />USE SHIMS
<br />WHEN
<br />INSTALLING TO
<br />KEEP PLUMB &
<br />LEVEL
<br />• SEALAM BEAD
<br />EXTERIOR • INTERIOR
<br />PRESSURE TREATED
<br />BUCKSTRIP (MIN. 21"
<br />AS SHOWN)
<br />SHIM AS NEEDED
<br />WINDOW
<br />ASTENER
<br />FILL INTERIOR VOID WITH
<br />MINIMAL EXPANDING FOAM
<br />- IF PER CODE
<br />I
<br />FAST
<br />THR
<br />PRE�CASr d
<br />d CONCRETE SILL
<br />SILL
<br />HEADER
<br />" 1 '
<br />INTERIOR
<br />EXTERIOR
<br />•
<br />• INTERIOR
<br />PRESSURE TREATED
<br />BUCKSTRIP (MIN. 2j'
<br />. c
<br />As SHOWN)
<br />v
<br />v.
<br />�
<br />SHIM AS NEEDED
<br />•
<br />WINDOW
<br />" Q
<br />y
<br />e
<br />•
<br />FILL INTERIOR
<br />MINIMAL
<br />- IF
<br />ASIENER
<br />VOID WITH
<br />EXPANDING FOAM
<br />PER CODE
<br />EXTERIOR
<br />JAMBS
<br />If NECESSARY,
<br />USE SHIMS
<br />WHEN
<br />INSTALLING TO •
<br />KEEP PLUMB & • • , - - -
<br />LEVEL d - - -
<br />4 tr d
<br />PRE-cASr
<br />d CONCRETE SILL -
<br />• SEALANT BEAD SILL
<br />screw embedment of 4' is maintained in the buckstrip. Window
<br />FLEXIBLE PLYWOOD
<br />INSTALLATION DETAILS FOR FLANGE WINDOWS IN
<br />WINDLONES OF 150MPH OR LESS (DETAIL A)
<br />fasteners should be located a maximum of 4" from each comer
<br />B FLASHING HEADER SHEATHING
<br />and maximum of 18" O.C. It is recommended that fasteners not
<br />be installed through the sill of the window. The actual size of
<br />RESISTANTWEATHER WINDOW
<br />Buckstrips must be set in a bead of sealant. The exterior joint
<br />between the buckstrip and masonry must also be sealed.
<br />the buckstrips should be no less than 1z" X 2 s". Buckstrips
<br />BARRIER FASTENER
<br />Buckstrips shall run the entire length of the rough opening. A
<br />should be installed using minimum 6" X 21" masonry screws,
<br />• •
<br />EXTERIOR I WOOD
<br />buckstrip is not necessary at the sill if it is pre -cast. All gaps
<br />to maintain 1 "embedment, and be 18" O.C.
<br />FACADE • '• • •` •• FRAME
<br />must be sealed. Buckstrips should be pressure treated yellow
<br />- HEADER
<br />pine, spruce or comparable lumber. In accordance with the
<br />• •
<br />� DRYWALL
<br />INSTALLATION DETAILS FOR FIN WINDOWS IN
<br />Florida Building Code, a taper, or bevel on the buck is
<br />WINDZONES OF 150MPH OR LESS (DETAIL B)
<br />RIGID FLASHING
<br />(OPT.. BY OTHERS)
<br />acceptable if the window frame is fully supported by the
<br />Installation fasteners for windows should be a
<br />buckstrip at both the interior and exterior.
<br />minimum 1J�" nail or 14" wood screws, with an embedment of
<br />INTERIOR FILL INTERIOR VOID WITH
<br />MINIMAL EXPANDING FOAM
<br />at least 1". Fasteners should be located at a maximum of 4"
<br />' - IF PER CODE
<br />If using thick wood buekstrips:
<br />from each corner and 18" O.C. for screws and 9" O.C. for
<br />•
<br />Installation fasteners should be a minimum 16" X 21" masonry
<br />nails. It is recommended that all screws or nails be sealed to
<br />screws, installed through the window and buckstrip, into the
<br />prevent infiltration of air and water. Product may be shimmed
<br />IF NECESSARY,
<br />masonry. Window may be shimmed as necessary, provided a
<br />as necessary.
<br />• USE SHIMS
<br />WHEN
<br />minimum screw embedment of A" is maintained in the
<br />Flexible flashing should be installed in a
<br />- Q
<br />- INSTALLING To
<br />masonry. Fasteners should be located a maximum of 4" from
<br />weatherboard fashion. The top layer should overlay any layer
<br />EVKEEP PLUMB kEL
<br />each corner and maximum of 18" O.C. It is recommended that
<br />beneath it. The weather resistant barrier should then cover the
<br />•WE `TMER
<br />fasteners not be installed through the sill of the window. The
<br />g
<br />flexible flashing at the header, The application of the weather
<br />RESISTANT FLEXIBLE
<br />BARRIER FLASHING
<br />actual size of the buckstrips should be no less than 4" X 2k",
<br />resistant barrier will vary based on when it is installed. If it is
<br />FINISHED
<br />FLDCIBLE SILL
<br />installed after the window, it should be tucked under the sill
<br />EXTERIOR WEATHER
<br />FLASHING RESISTANT • •
<br />If using III" thick or greater wood buckstrips (not shown):
<br />flashing and overlap the jambs and head flashing.
<br />, , ARCHFITCTURAL
<br />�� ®AMERICAN
<br />„o MANUFACTURES
<br />M
<br />JAMBS BARRIER
<br />•
<br />EXTERIOR
<br />FACADE
<br />Window installation fasteners should be a minimum #8 X 1"
<br />wood screws, installed through the window into the buckstrip.
<br />Window may be shimmed as necessary, provided a minimum
<br />WINDOW
<br />FASTENER
<br />SILL
<br />e window depicted in this drawing Is intended tor use on typical construction. it is icresponsibility oflithers to determine r Tt is applicable. Additional flashing, vapor
<br />barriers, etc. may be specified by the project architect. Wind and design pressures vary within each state and county. All products manufactured by NuAir Inc. meet a
<br />minimum of 110 mph (R30 DP) wind load requirements (per AAMA 101); please check local building codes for exact requirements. Above details shown for Single Hung
<br />• SEALANT BEAD
<br />window. For installation of Awning, Horizontal Roller, or Picture/Designer windows use the same specifications as shown above for the Single Hung, provided that all
<br />OSEALANT BEAD IF FLASHING IS NOT ADHESIVE
<br />re- inched frame installation holesare utilized and with the above mentioned screw size a andspacing.
<br />INSTALLATION DETAILS FOR NON -IMPACT, FLANGE, SINGLE
<br />HUNG WINDOWS IN WINDZONES OF 15OMPH OR LESS (per FBC 2001)
<br />Buckstrips must be set in a bead of sealant. The exterior joint
<br />between the buckstrip and masonry must also be sealed.
<br />Buckstrips shall run the entire length of the rough opening. A
<br />buckstrip is not necessary at the sill if it is pre -cast. All gaps must
<br />be sealed. Buckstrips should be pressure treated yellow pine,
<br />spruce or comparable lumber. In accordance with the Florida
<br />Building Code, a taper, or bevel on the buck is acceptable if the
<br />window frame is fully supported by the buckstrip at both the
<br />interior and exterior.
<br />If using thick wood buckstrips.
<br />Installation fasteners should be a minimum 6" X 21" masonry
<br />screws, installed through the window and buckstrip, into the
<br />masonry. Window may be shimmed as necessary, provided a
<br />minimum screw embedment of IQ" is maintained in the masonry.
<br />Fasteners should be located a maximum of 4" from each corner
<br />and maximum of 18" O.C. It is recommended that fasteners not be
<br />installed through the sill of the window. The actual size of the
<br />buckstrips should be no less than 4" X 2-".
<br />If using 1� " thick or greater wood buekstrins (not shown):
<br />Window installation fasteners should be a minimum #10 X 1i "
<br />wood screws, installed through the window into the buckstrip.
<br />Window may be shimmed as necessary, provided a minimum
<br />screw embedment of 1Jq" is maintained in the buckstrip. Window
<br />fasteners should be located a maximum of 4" from each comer and
<br />maximum of 18" O.C. It is recommended that fasteners not be
<br />installed through the sill of the window. The actual size of the
<br />buckstrips should be no less than 1�" X 2j". Buckstrips should be
<br />installed using minimum 6" X 21" masonry screws, to maintain
<br />1Jq" embedment, and be 18" O.C.
<br />The window depicted in this drawing is intended for use on typical construction. It is the
<br />AMERICAN
<br />ARCHITECTUTtAL responsibility of others to determine if it is applicable. Additional flashing, vapor barriers, etc.
<br />ASSOCIATION ES may be specified by the project architect. Wind and design pressures vary within each state and
<br />FA 7 1A IR mME]MITER
<br />county. All products manufactured by NuAir Inc. meet a minimum of 110 mph (R30 DP) wind
<br />Tampa, FL•(800) 282-6627•www.NuAir.com load requirements (per AAMA 101); please check local building codes for exact requirements.
<br />HEADER SERIES I INSTALLATION DETAILS FOR NON -IMPACT, FLANGE, AWNING
<br />IA02/3 ATW I WINDOWS IN WINDZONES OF 15OMPH OR LESS (per FBC 2001)
<br />Buckstrips must be set in a bead of sealant. The exterior joint
<br />° • between the buckstrip and masonry must also be sealed.
<br />• Buckstrips shall run the entire length of the rough opening. A
<br />EXTERIOR INTERIOR buckstrip is not necessary at the sill if it is pre -cast. All gaps must
<br />INTERIOR
<br />.d
<br />v
<br />�v
<br />v�
<br />EXTERIOR
<br />JAM BS FASTENERS
<br />THROUGH
<br />SILL
<br />IF NECESSARY,
<br />USE SHIMS
<br />WHEN FINIS
<br />INSTALLING TO SILL
<br />KEEP PLUMB & •
<br />LEVEL • _ _ _
<br />•
<br />4 a d
<br />PRE -CAST
<br />d CONCRETE SILL
<br />• SEALANT BEAD SILL
<br />• PRESSURE TREATED
<br />be sealed. Buckstrips should be pressure treated yellow pine,
<br />BUCKSTRIP (MIN. 2j'
<br />spruce or comparable lumber. In accordance with the Florida
<br />AS SHOWN)
<br />Building Code, a taper, or bevel on the buck is acceptable if the
<br />SHIM AS NEEDED
<br />window frame is fully supported by the buckstrip at both the
<br />interior and exterior.
<br />WINDOW
<br />FASTENER
<br />If usii4" thick wood buckstrips:
<br />Installation fasteners should be a minimum 16" X 24" masonry
<br />screws, installed through the window and buckstrip, into the
<br />FILL INTERIOR VOID WITH
<br />MINIMAL EXPANDING FOAM
<br />masonry. Window may be shimmed as necessary, provided a
<br />- IF PER CODE
<br />minimum screw embedment of l4" is maintained in the masonry.
<br />Fasteners should be located a maximum of 4" from each comer
<br />and maximum of 18" O.C. It is recommended that fasteners not be
<br />installed through the sill of the window. The actual size of the
<br />buckstrips should be no less than 4" X 21".
<br />If using 14 " thick or greater wood buckstrips (not shown):
<br />RED
<br />•
<br />Window installation fasteners should be a minimum #10 X 1# "
<br />wood screws, installed through the window into the buckstrip.
<br />- -
<br />-
<br />Window may be shimmed as necessary, provided a minimum
<br />•
<br />screw embedment of 14" is maintained in the buckstrip. Window
<br />PouR92b
<br />fasteners should be located a maximum of 4" from each corner and
<br />,Q CONCRETE SILL
<br />maximum of 18" O.C. It is recommended that fasteners not be
<br />installed through the sill of the window. The actual size of the
<br />buckstrips should be no less than lz" X 28". Buckstrips should be
<br />installed using minimum 16" X 24" masonry screws, to maintain
<br />1i" embedment, and be 18" O.C.
<br />The window depicted in this drawing is intended for use on typical construction. It is the
<br />ARCHITE N
<br />MANUFACTURES
<br />responsibilityf other t t rmin ifit i applicable. Additional flashin va or barn te.
<br />o s o determine e t s a cab e.barriers, e
<br />g, P >
<br />MANUFACTURES
<br />714N� RPP
<br />ASSocrAn N may be specified b the project architect. Wind and design pressures v within each state and
<br />Y P Y P J n !m P vary
<br />MEMBER
<br />county. All products manufactured by NuAir Inc. meet a minimum of 110 mph (R30 DP) wind
<br />Tampa, FL•(800) 282-66270www.NuAir.com load requirements (per AAMA 101); please check local building codes for exact requirements.
<br />FLEXIBLE
<br />FLASHING
<br />HEATHER
<br />MISTANT-
<br />BARRIER
<br />RIGID FLASHING(OPT., BY OTHERS)
<br />HEADER
<br />SERIES
<br />INSTALLATION DETAILS FOR NON -IMPACT, FIN, HORIZ. ROL-
<br />SPLYWOOD HEATHING
<br />OH2/3 HR
<br />LER WINDOWS IN WINDZONES OF 15OMPH OR LESS (per FBC 2001)
<br />WINDOW
<br />FASTENER
<br />Window Installation:
<br />f
<br />•
<br />"''
<br />» '' +
<br />WOOD
<br />Installation fasteners for windows should
<br />-
<br />FRAME
<br />be a minimum 1 j", 4d nail or 6 x 1�" drywall screw,
<br />•
<br />HEADER
<br />with an embedment of at least 1�". Fasteners
<br />DRYWALL
<br />should be located at a maximum of 4" from each
<br />comer and 18" O.C. for screws and 9" O.C. for
<br />nails.
<br />FILL INTERIOR VOID FWITH
<br />OAM MINIMAL EXPANDING FOAM
<br />It is recommended that all screws or
<br />- IF PER CODE
<br />nails be sealed to prevent infiltration of air and
<br />water. Product may be shimmed as necessary.
<br />IF NECESSARY,
<br />USE SHIMS
<br />Weatherproofing:
<br />WHEN
<br />INSTALLING KEEP PLUMBe�
<br />Flexible flashing should be installed in a
<br />LEVEL
<br />weatherboard fashion. The top layer should overlay
<br />any layer beneath it. The weather resistant barrier
<br />;Hm should then cover the flexible flashing at the
<br />header.
<br />The application of the weather resistant
<br />• barrier will vary based on when it is installed. If it
<br />EXTERIOR is installed after the window, it should be tucked
<br />FACADE
<br />WINDOWunder the sill flashing and overlap the jambs and
<br />FASTENER head flashing.
<br />SILL • SEALANT BEAD
<br />OSEALANT BEAD IF FLASHING IS NOT ADHESIVE
<br />The window depicted in this drawing is intended for use on typical construction. It is the
<br />AMERICMANUF AN
<br />ARCHITECTURAL responsibility of others to determine if it is applicable. Additional flashing, vapor barriers, etc.
<br />MANUFACTURES
<br />AssoclAnUN maybe specified by the project architect. Wind and design pressures vary within each state and
<br />MEMBER county. All products manufactured by NuAir Inc. meet a minimum of 110 mph (R30 DP) wind
<br />Tampa, FL•(800) 282-66276www.NuAir.00m load requirements (per AAMA 101); please check local building codes for exact requirements.
<br />FLEXIBLEN
<br />HEADER PLYWOOD SERIES 900
<br />INSTALLATION DETAILS FOR NON -IMPACT, FIN, SINGLE
<br />SHEATHING & 950 SH
<br />HUNG WINDOWS IN WINDZONES OF 150MPH OR LESS (per FBC 2001)
<br />Window Installation:
<br />WEATHER WINDOW
<br />RESISTANT FASTENER
<br />BARRIER
<br />i
<br />• •
<br />EXTERIOR
<br />Installation fasteners for windows should
<br />FACADE
<br />» WOOD
<br />'i FRAME
<br />be a minimum A", 4d nail or 6 x 12" drywall screw,
<br />• • HEADER
<br />with an embedment of at least 1z". Fasteners
<br />RIGID FLASHING
<br />DRYWALL
<br />should be located at a maximum of 4" from each
<br />(OPT., BY OTHERS)
<br />corner and 18" O.C. for screws and 9" O.C. for
<br />INTERIOR
<br />FILL INTERIOR VOID WiTH
<br />nails.
<br />MINIMAL EXPANDING FOAM
<br />It is recommended that all screws or
<br />IF PER CODE
<br />nails be sealed to prevent infiltration of air and
<br />-'' •
<br />water. Product may be shimmed as necessary.
<br />IF NECESSARY,
<br />•
<br />USE WHDSHIMS
<br />Weatherproofing:
<br />- -Q
<br />INSrAWNG TO
<br />KEEP PLUMB &
<br />LEVEL
<br />Flexible flashing should be installed in a
<br />• WEATHER FLEXIBLE weatherboard fashion. The top layer should overlay
<br />RESISTANT FLASHING
<br />BARRIER FINISHED any layer beneath it. The weather resistant barrier
<br />DTTERIOR FLEXIBLE WEATHER SILL should then cover the flexible flashing at the
<br />FLASHING RESISTANT • •_ header.
<br />JAMBS BARPoER The application of the weather resistant
<br />EXTERIOR • barrier will vary based on when it is installed. If it
<br />FACADE is installed after the window, it should be tucked
<br />WINDOW
<br />FASTENER under the sill flashing and overlap the jambs and
<br />SILL head flashing.
<br />• SEALANT BEAD
<br />OSEALANT BEAD IF FLASHING IS NOT ADHESIVE
<br />The window depicted in this drawing is intended for use on typical construction. It is the
<br />' AH ILAL responsibility of others to determine if it is applicable. Additional flashing, vapor barriers, etc.
<br />MANUFACTURESa be s ecified b the ro'eet architect. Wind and desi ressures v within each state and
<br />M...
<br />ASSOCIATION may P Y project P �Y
<br />MEMBER county. All products manufactured by NuAir Inc. meet a minimum of 110 mph (R30 DP) wind
<br />Tampa, FL9(800) 282-6627*www.NuAiccom load requirements (per AAMA 101); please check local building codes for exact requirements.
<br />HEADER
<br />PLYWOOD SERIES
<br />FLASHING
<br />sHEATHINc A02/3 ATW
<br />WEATHER
<br />WINDOW
<br />RESISTANT
<br />ASTENER
<br />BARRIER I
<br />••
<br />EXTERIOR
<br />FACADE
<br />WOOD
<br />•
<br />:. i FRAME
<br />.. HEADER
<br />RIGID FLASHING
<br />•
<br />(oPr., BY OTHt7RS)
<br />DRYWALL
<br />INTERIOR
<br />WEATHER
<br />C"• ESISTANT
<br />FILL INTERIOR VOID WiTH
<br />� % BARRIER
<br />MINIMAL EXPANDING FOAM
<br />- IF PER CODE
<br />:: •
<br />IF NECESSARY,
<br />•
<br />USE SHIMS
<br />WHEN
<br />-----
<br />INSTALLING TO
<br />KEEP PLUMB &
<br />LEVEL
<br />• FLEXIBLE
<br />FLEXIBLE FLASHING
<br />FLASHING
<br />FINISHED
<br />EXTERIOR WEATHER
<br />SILL.
<br />RESISTANT
<br />•
<br />JAMBS BARRIER •
<br />—_=_ — __
<br />EXTERIOR
<br />FACADE
<br />I
<br />I WINDOW
<br />FASTENER
<br />SILL
<br />• SEALANT BEAD
<br />OSEALANT BEAD IF FLASHING IS NOT ADHESIVE
<br />INSTALLATION DETAILS FOR NON -IMPACT, FIN, AWNING
<br />WINDOWS IN WINDZONES OF 15OMPH OR LESS (per FBC 2001)
<br />Window Installation:
<br />Installation fasteners for windows should
<br />be a minimum *, 4d nail or 6 x 1�' drywall screw,
<br />with an embedment of at least i?". Fasteners
<br />should be located at a maximum of 4" from each
<br />corner and 18" O.C. for screws and 9" O.C. for
<br />nails.
<br />It is recommended that all screws or
<br />naiIs be sealed to prevent infiltration of air and
<br />water. Product may be shimmed as necessary.
<br />Weatherproofing:
<br />Flexible flashing should be installed in a
<br />weatherboard fashion. The top layer should overlay
<br />any layer beneath it. The weather resistant barrier
<br />should then cover the flexible flashing at the
<br />header.
<br />The application of the weather resistant
<br />barrier will vary based on when it is installed. If it
<br />is installed after the window, it should be tucked
<br />under the sill flashing and overlap the jambs and
<br />head flashing.
<br />,R 10 AN
<br />The window depicted in this drawing is intended for use on typical construction. It is the A
<br />ARCHITECTURAL responsibility of others to determine if it is applicable. Additional flashing, vapor barriers, etc.
<br />MANUFACTURES
<br />ASSOCISSOCI ATION maybe specified by the project architect. Wind and design pressures vary within each state and
<br />MEMBER county. All products manufactured by NuAir Inc. meet a minimum of 110 mph (R30 DP) Wind
<br />Tampa, FL•(800) 282-66279www.NuAiccom load requirements (per AAMA 101); please check local building codes for exact requirements.
<br />FLEXIBLE
<br />HEADER
<br />PLYWOOD SERIES 900
<br />INSTALLATION DETAILS FOR NON -IMPACT, FIN, FIXED
<br />FLASHING SHEATHING PW & DPW
<br />WINDOWS IN WINDZONES OF 150MPH OR LESS (per FBC 2001)
<br />WEATHER WINDOW
<br />RESISTANT
<br />FASTENER
<br />Window Installation:
<br />BARRIER I
<br />• •
<br />EXTERIOR
<br />Installation fasteners for windows should
<br />WOOD
<br />FACADE i » :. ; FRAME
<br />be a minimum 4', 4d nail or 6 x 1i" drywall screw,
<br />• •
<br />HEADER
<br />with an embedment of at least 1�". Fasteners
<br />RIGID FLASHING
<br />DRYWALL
<br />should be located at a maximum of 4" from each
<br />(OPT., BY OTHERS)
<br />corer and 18" O.C. for screws and 9" O.C. for
<br />INTERIOR
<br />nails.
<br />It is recommended that all screws or
<br />Ft..
<br />`•
<br />nails be sealed to prevent infiltration of air and
<br />; • FILL INTERIOR VOID WITH
<br />water. Product may be shimmed as necessary.
<br />MINIMAL EXPANDING FOAM
<br />- IF PER CODE
<br />IF NECESSARY,
<br />USE SHIMS
<br />•
<br />-- Q_
<br />WHEN
<br />INSTALLING TO
<br />Weatherproofing:
<br />___
<br />KEEP PLUMB &
<br />7
<br />LEVEL-
<br />Flexible flashing should be installed in a
<br />• RTfT FLEXIBLE
<br />weatherboard fashion. The top layer should overlay
<br />Ater
<br />BARRIER FLASHING
<br />any layer beneath it. The weather resistant barrier
<br />EXTERIOR ISLE WEATHER
<br />FINISHED
<br />SILL
<br />should then cover the flexible flashing at the
<br />FLASHINGBARR� •
<br />•
<br />header.
<br />JAMBS
<br />_
<br />The application of the weather resistant
<br />EXTERIOR •
<br />barrier will vary based on when it is installed. If it
<br />FACADE
<br />is installed after the window, it should be tucked
<br />WINDOW
<br />FASTENER
<br />under the sill flashing and overlap the jambs and
<br />SILL
<br />head flashing.
<br />• SEALANT BEAD
<br />OSEALANT BEAD IF FLASHING IS NOT ADHESIVE
<br />The window depicted in this drawing is intended for use on typical construction. It is the
<br />AxcHITEcruRAL
<br />responsibility of others
<br />to determine if it is applicable. Additional flashing, vapor barriers etc.
<br />e pp g, p ,
<br />MAMBRIC' MAWFAN
<br />MANUFACTURES
<br />ASSOCIATION
<br />may be specified by the project architect. Wind and design pressures vary within each state and
<br />MEMBER
<br />county. All products manufactured
<br />by NuAir Inc. meet a minimum of 110 mph (R30 DP) wind
<br />Tampa, FL•(800) 282-6627owww.NuAir.com
<br />load requirements (per AAMA 101); please check local building codes for exact requirements.
<br />HEADER SERIES
<br />INSTALLATION DETAILS FOR NON -IMPACT, FLANGE, HORiZ. ROL-
<br />OH2/3 HR
<br />LER WINDOWS IN WINDZONES OF 150MPH OR LESS (per FBC 2001)
<br />Buckstrips must be set in a bead of sealant. The exterior joint
<br />° •
<br />between the buckstrip and masonry must also be sealed.
<br />Buckstrips shall nun the entire length of the rough opening. A
<br />EXTERIOR INTERIOR
<br />buckstrip is not necessary at the sill if it is pre -cast. All gaps must
<br />PRESSURE TREATED
<br />be sealed. Buckstrips should be pressure treated yellow pine,
<br />BUCKSTRIP (MIN. 2j'
<br />spruce or comparable lumber. In accordance with the Florida
<br />AS SHOWN)
<br />Building Code, a taper, or bevel on the buck is acceptable if the
<br />window frame is fully supported by the buckstrip at both the
<br />,.INTERIOR
<br />SHIM AS NEEDID
<br />interior and exterior.
<br />HnNDOW
<br />FASTENERIfusing
<br />"thick wood bucksirips:
<br />Installation fasteners should be a minimum 16"X 21" masonry
<br />FlLL INTERIOR VOID WITH
<br />MINIMAL EXPANDING FOAM
<br />`i�nTtRloR
<br />screws, installed through the window and buckstrip, into the
<br />- IF PER CODE
<br />masonry. Window may be shimmed as necessary, provided a
<br />JAMBS
<br />minimum screw embedment of 14" is maintained in the masonry.
<br />Fasteners should be located a maximum of 4" from each comer
<br />and maximum of 18" O.C. It is recommended that fasteners not be
<br />NO
<br />installed through the sill of the window. The actual size of the
<br />FASTENERS
<br />buckstrips should be no less than 4" X 2J".
<br />IF NECESSARY, THROUGH
<br />USE SHIMS SILL
<br />If using I } " thick or greater wood buckstrips (not shown):
<br />•
<br />Window installation fasteners should be a minimum #10 X I "
<br />INSTALLING To
<br />KEEP PLUMB & • -
<br />wood screws, installed through the window into the buckstrip,
<br />LEVEL • • . -_-_-_ -
<br />Window may be shimmed as necessary, provided a minimum
<br />•
<br />screw embedment of 11" is maintained in the buckstrip. Window
<br />d
<br />C
<br />° �7 AT, POURPb
<br />fasteners should be located a maximum of 4" from each comer and
<br />PRE -CAST
<br />° CONCRETE SILL d CONCRETE SILL
<br />maximum of 18' O.C. It is recommended that fasteners not be
<br />installed through the sill of the window. The actual size of the
<br />• SEALANT BEAD SILL
<br />buckstrips should be no less than * X 21". Buckstrips should be
<br />installed using minimum 16" X 24" masonry screws, to maintain
<br />1Jq" embedment, and be 18" O.C.
<br />The window depicted in this drawing is intended for use on typical construction. It is the
<br />ANARCHITECTURAL responsibility of others to determine if it is applicable. Additional flashing, vapor barriers, etc.
<br />ASSO ;IAAT(O N may be specified by the project architect. Wind and design pressures vary within each state and
<br />A �� MIKUMBER
<br />county. All products manufactured by NuAir Inc. meet a minimum of 110 mph (R30 DP) wind
<br />Tampa, FL•(800) 282-6627•www.NuAir.com load requirements (per AAMA 101); please check local building codes for exact requirements.
<br />HEADER SERIES 900
<br />INSTALLATION DETAILS FOR NON -IMPACT, FLANGE, FIXED
<br />— PW & DPW
<br />WINDOWS IN WINDZONES OF 15OMPH OR LESS (per FBC 2001)
<br />4
<br />Buckstrips must be set in a bead of sealant. The exterior joint
<br />•
<br />between the buckstrip and masonry must also be sealed.
<br />Buckstrips shall run the entire length of the rough opening. A
<br />EXTERIOR INTERIOR
<br />buckstrip is not necessary at the sill if it is pre -cast. All gaps must
<br />•
<br />INTERIOR PRESSURE TREATED
<br />be sealed. Buckstrips should be pressure treated yellow pine,
<br />• BUCKSTRIP (MIN. 2j'
<br />spruce or comparable lumber. In accordance with the Florida
<br />AS SHOWN)
<br />Building Code, a taper, or bevel on the buck is acceptable if the
<br />window frame is fully supported by the buckstrip at both the
<br />SHIM AS NEEDED
<br />01
<br />interior and exterior.
<br />WINDOW
<br />. • ASiENER
<br />If using4" thick wood buckstrips:
<br />Q FILL INTERIOR VOID WITH
<br />146 n
<br />Installation fasteners should be a minimum 16 X 24 masonry
<br />MINIMAL EXPANDING FOAM
<br />a �;: • - IF PER CODE
<br />screws, installed through the window and buckstrip, into the
<br />EXTERIOR
<br />masonry. Window may be shimmed as necessary, provided a
<br />JAMBS
<br />minimum screw embedment of la' is maintained in the masonry.
<br />Fasteners should be located a maximum of 4" from each comer
<br />and maximum of 18" O.C. The actual size of the buckstrips should
<br />NO
<br />FASTENERS
<br />be no less than 4" X 2s�
<br />THROUGH
<br />SILLIf
<br />using 1 "thick or greater wood buckstrips (not shown):
<br />USE SHHIIMS
<br />IF NECESSARY,tA�OPNICRE
<br />Window installation fasteners should be a minimum #10 X 1f'
<br />INSTAWNG TOWHEN
<br />wood screws, installed through the window into the buckstiip.
<br />KEEP PLUMB &_-_ _
<br />Window may be shimmed as necessary, provided a minimum
<br />LEVELscrew
<br />embedment of 14"is maintained in the buckstrip. Window
<br />fasteners should be located a maximum of 4" from each corner and
<br />TONC ETESt
<br />CONCRETE SILL
<br />maximum of 18" O.C. The actual size of the bucksttips should be
<br />SILL d
<br />no less than + X 2s'. Buckstrips should be installed using
<br />SEALANT BEAD SILL
<br />minimum 16' X 2a' masonry screws, to maintain
<br />•
<br />la" embedment, and be 18" O.C.
<br />The window depicted in this drawing is intended for use on typical construction. It is the
<br />HIS"RAL responsibility of others to determine if it is applicable. Additional flashing, vapor barriers, etc.
<br />��
<br />MANUFACTURES
<br />ASSOCIATON may be specified b the project ct dpressures va withi ea h state and
<br />Y P Y P oJect architect. Wind an design vary n e
<br />®
<br />MEMBER
<br />county. All products manufactured by NuAir Inc. meet a minimum of 110 mph (R30 DP) wind
<br />Tampa, FL•(800) 282.6627*www.NuAir.com load requirements (per AAMA 101); please check local building codes for exact requirements.
<br />SERIES 200
<br />INSTALLATION DETAILS FOR NON -IMPACT, SLIDING GLASS
<br />HEADER & 500 SGD
<br />DOORS IN WINDZONES OF 150MPH OR LESS (per FBC 2001)
<br />Buckstrips must be set in a bead of sealant. The exterior joint
<br />between the buckstrip and masonry must also be sealed.
<br />Buckstrips shall nm the entire length of the rough opening,
<br />IOR• INTERIOR
<br />except door sill. All gaps must be sealed. Buckstrips should be
<br />INTERIOR PR SURE
<br />pressure treated yellow pine, spruce or comparable lumber. In
<br />mE`�
<br />BUCKSTRIP
<br />accordance with the Florida Building Code a taper, or bevel
<br />g � P �
<br />•
<br />on the buck is acceptable if the door frame is fully supported
<br />SHIM
<br />s M
<br />by the buckstrip at both the interior and exterior.
<br />NEEDED
<br />DOOR
<br />If using t thick wood buckstrips:
<br />Installation fasteners should be a minimum jJy" X 24I masonry
<br />screws, installed through the door frame and buckstrip, into the
<br />'
<br />masonry. Door may be shimmed as necessary, provided a
<br />I, I
<br />minimum screw embedment of 14" is maintained in the
<br />i MINIMUM
<br />masonry. Fasteners should be located a maximum of 4" from
<br />RECOM-
<br />each comer and maximum of 18" O.C. The width of the
<br />MENDED
<br />buckstrips should be no less than the frame frame of the door.
<br />• • AFTER
<br />INSTALLATION, SEAL
<br />JAMBS HORIZONTAL JOINT
<br />If using 4 " thick or greater wood buckstrips (not shown):
<br />BETWEEN TRACK
<br />Door installation fasteners should be a minimum #10 X 1i"
<br />AND JAMB
<br />wood screws, installed through the window into the buckstrip.
<br />EXTERIOR
<br />Door may be shimmed as necessary, provided a minimum
<br />screw embedment of IQ" is maintained in the buckstrip. Door
<br />FILL INTERIOR VOID WITH IF NECESSARY
<br />d
<br />fasteners should be located a maximum of 4" from each comer
<br />MINIMAL IFDPER CODE ANDING FOAM
<br />° USE SHIMS WHEN
<br />and maximum of 18" O.C. The width of the buckstrips should
<br />KEEP pule dcTLEVEI
<br />be no less than the frame frame of the door. Buckstrips should
<br />• SEALANT BEAD TRACK
<br />be installed using minimum 16" X 24" masonry screws, to
<br />maintain 14" embedment, and be 18" O.C.
<br />The door depicted in this drawing is intended for use on typical construction. It is the
<br />ARCIUM N
<br />responsibility of others to determine if it is applicable. Additional flashing, vapor barriers, etc.
<br />/
<br />MANUFACTURES
<br />MANUFACTURLS
<br />ASSOCIATION m be specified t a ed b he project architect. Wind and design pressures vary within each state an
<br />Y P Y P J � F rY d
<br />MEMBER
<br />county. All products manufactured by NuAir Inc. meet a minimum of 110 mph (R30 DP) wind
<br />Tampa, FLo(800) 282-6627*www.NuAir.com load requirements (per AAMA 101); please check local building codes for exact requirements.
<br />SERIES 200
<br />INSTALLATION DETAILS FOR NON -IMPACT, SLIDING GLASS
<br />& 500 SGD
<br />DOORS IN WINDZONES OF 150MPH OR LESS (per FBC 2001)
<br />HEADER
<br />Sliding Glass Door Installation:
<br />Installation fasteners for jambs and
<br />INTERIOR
<br />header should be a minimum #10 X 1" screw.
<br />• •INTERIOR
<br />Installation fasteners for the track should be a
<br />SHIO • DOOR M
<br />/FASTENER NEEDED
<br />minimum 1�' masonry screw. All fasteners should
<br />have an embedment of at least 11-". Fasteners
<br />/
<br />should be located at a maximum of 4" from each
<br />ii i
<br />corner and 18" O.C. for screws.
<br />It is recommended that all screws be
<br />�; I
<br />sealed to prevent infiltration of air and water.
<br />Product may be shimmed up to 4" if necessary.
<br />MINIMUM
<br />I� I t1+
<br />COM-
<br />JAMBS ' RENDED
<br />MENDED
<br />Weatherproofing:
<br />• AFTER
<br />INSTALLATION, SEAL
<br />Flexible flashing should be installed in a
<br />g
<br />HORIZONTAL JOINT
<br />weatherboard fashion. The top layer should overlay
<br />EXTERIOR BETWEEN B CK
<br />AND
<br />any layer beneath it. The weather resistant barrier
<br />should then cover the flexible flashing at the
<br />header.
<br />FILL INTERIOR VOID WiTH
<br />The application of the weather resistant
<br />MINIMAL EXPANDING FOAM d . IFII ECESSAIM
<br />d USE SHIMS WHEN
<br />barrier will vary based on when it is installed. If it
<br />,
<br />- IF PER CODE INSTALLING TO
<br />is installed after the door, it should be tucked under
<br />. KEEP PLUMB &
<br />the sill flashing and overlap the jambs and head
<br />• SEALANT BEAD TRACK
<br />flashing.
<br />The door depicted in this drawing is intended for use on typical construction. It is the
<br />AMExlcnry
<br />ARCHITECTURAL responsibility of others to determine ifit a
<br />P ty termm rt is applicable. Additional flashing, vapor barriers, etc.
<br />MANUFACTURes
<br />ASSOCIATION m e$ specified b the project architect. i n 1 r h• may b y y e p Jec c ct. Wind and design pressures vary within each state and
<br />•
<br />MEMBER
<br />county. All products manufactured by NuAir Inc. meet a minimum of 110 mph (R30 DP) wind
<br />Tampa, FLO(800) 282-66270www.NuAir.com load requirements (per AAMA 101); please check local building codes for exact requirements.
<br />0
<br />1
<br />THERMA-TRU INSTALLATION
<br />KEY DIFFERENCES CHECK LIST
<br />Rout openings are 1/4" smaller on each side and 1/4" smaller on the
<br />header than standard Thermo-Tru rough opening dimensions.
<br />Use only a maximum of 1/4" thick shirrs,
<br />Predrill the jambs and headers using 1/8" drill bit, Predrilling
<br />increases structural performance.
<br />Use only 8-1/2" wood screws (#8 and #10) when securing the pre
<br />hung frame to the rough opening buck, Drywall screws, deck screws,
<br />and nails are insufficient anchors, and should not be substituted for
<br />wood screws,
<br />Be certain of the number and placement of all screws securing the frame
<br />to the rough opening buck, Consult the architect or engineer of record
<br />concerning Tastening the buck to the rest of the building structure,
<br />CONTRACTOR TO PROVIDE A 1 x P,T, BUCK STRIP CONT, AT
<br />OPENING SIDES AND HEADER,
<br />1 x BUCK STRIPS WILL BE ACCEPTABLE PROVIDED THE
<br />3/16" DIA FLATHEAD TAPCONS ARE PROVIDED SPACED AS
<br />SHOWN. THE TAPCONS ARE TO BE CONTINUOUS THRU THE
<br />OOOOR /4""MEhBEDMENT BINTO THE I MASONRYA JAMBS MINIMUM
<br />6" 6
<br />SPAC
<br />EVEI
<br />6" 6
<br />6„ 6"
<br />SINGLE DOOR
<br />r
<br />V
<br />r
<br />r
<br />SINGLE DOOR W SIDELITE SINGLE DOOR W/ SIDELITES
<br />11
<br />" 6
<br />"
<br />IiI
<br />III
<br />II I
<br />II I
<br />I II
<br />I II
<br />III
<br />III
<br />E
<br />E
<br />E
<br />y
<br />" / "
<br />!r
<br />,
<br />6
<br />u
<br />1
<br />DOUBLE DOOR W/ SIDELITES
<br />6,
<br />PACE
<br />VENL
<br />I I
<br />I i
<br />i
<br />f
<br />I
<br />6
<br />4W
<br />o
<br />CREATED 01-02-02
<br />120 MPH
<br />3 SEC. GUST
<br />SPACE
<br />7VENLY
<br />a
<br />
|