360 S Rosemary Ave Ste 400 (2) - Laserfiche WebLink

Browse Search

L-SERIES SPECIFICATIONS ARCHITECT/ENGINEER SPECIFICATIONS GENERAL L-Series standard horns, strobes, and horn str-obes S1131t Mount to n standard 2 x 4 x 1. 7/8-inch back box, 4 - 4 x 1l/2.-inch back box, 4-inch octagon back box, or double -gang bac, box. L-Series compact products shalt mount to a single -gang 2 x 4 x I 7/8-inch back box. A universal mounting plate shali 1)e usi,.J for mounting ceiling and wall products for all standard models and a separate universal mounting plate shalt be used for mounting wall Compact models. The notification appliance circuit wiring shalt terminate at the universal mounting plate. Atso: L-Series products, when used with the Sync -Circuit"` Module accessory, shall be powered from a non - coded notification appliance circuit output and shall operate on a nominal 12 or 24votts. When used with the Sync -Circuit Module, 12-volt-rated notification appliance circuit outputs shall operate between 8.5 and 17.5 volts: 24-volt-rated notification appliance circuit outputs shalt operate oetween 16.5 and' 33 volts. Indoor L-Series products shall operate between 32 and 120 degrees Fahrenheit from a regulated DC or fLiLi-WaVe rectified unfiltered power supply. Strobes and horn strobes shalt have field -selectable candela settings including 15. 3075, 95, 110, 135, and 185. STROBE The strobe shall be a System Scns>o( L-SLrls Model ------- listed to UL 1971 and shalt be approved for fire protective service. The strobe shall be wired as a primary --signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances, flasriioyat 1 Hz over the strobe's entire operating voltage range. The strobe tight shalt consist of a xenon flash tube and associated ie,.s/reftector system, HORN STROBE COMBINATION The horn strobe shalt be a System, Sensor L-Series Model------- listed to UL 1971 and UL 4614 and shall be approved for fire protective service. The horn strobe shall be wired as a primary -signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances, flashing at 1 Hz over the strobe's entire operating voltage range. The strobe tight she[" consist of a xenon flash tubc and associated tens/reflector system. The horn shalt have two audibility options and an option to switch between a temporal three pattern and a non -temporal (continuous) pattern. These options are set by a multiple position switch. The horn on hcrn su c:bemode[s shalt operate on a coded or non -coded power supply. SYNCHRONIZATION MODULE The module shalt be a System S�nsor 5yiiC'Ci1_CUit modet MD L3 listed to UL 464 and shalt be approved for fire protective service. The module shalt synchronize L- Sea ies strobes at 1 Hz and horns at temporal three. Also. while operating the strobes, the module shall silence the horns on horn strobe rnodeis over a single pair of wires. The module shalt mount to a 4 11/16 - 4 11/16 X 2 1/8-inch back box. The module shall also co. oral two S, yie Y (class B) circuits or one Style Z (class A) Circuit. The module shall synchronize multiple zones. Daisy chaining two or n-iore synchronization modules together will synchronize all the zones they control, The module shall not operate on a coded power sutipty. PHYSICAL Wall -Mount Dimensions (including Let -is) .'_I Compact Wall -Mount Dimensions (including lens): x 1, 91 3 13, 3 1 x P'-, Horn Dimensions 71,.,.," 4 32 t - 1 f , , 1- , , Compact Horn Dimensions: ELECTRICAL SPECIFICATIONS Strobe Flash Rate: Nominal Voltage Regulated : Operating Voltage Range V Operating Voltage Rangu� 'MDL3) Sync Input Terminal Wire Gauge; 1 ENVIRONMENTAL Standard Operating Humidity Range: Notes; AGENCY LISTINGS AND APPROVALS UL: I J FM:/L�,_ CSFM: