Laserfiche WebLink
<br /> <br />3. Satts and Slankets'-Nom 2-1/2 in. thick glass fiber batts with glass fiber mat septum, . <br />plied in 16 or 24 in. widths, installed to fill interior of stud cavities and friction held. " <br />Owen.Corning Fiberglas Corp.-Type FB. <br />4. Wallboard, Gypsum.-1I2 in. thick, 4 ft wide. applied vertically, attached to steel studa <br />floor and ceiling runners with 0.127 in. diam self-drilling. self-tapping steel screws. 1 'In. I <br />spaced 8 in. O.C. along edges of boards and 12 in. O.C. in the field of the boards. JointS <br />tered over studs and staggered on opposite sides of the assembly. )1'; <br />See Wallboard, Gypsum (CKNX) Category for names of manufacturers. . ...~ <br />5. Joint Tape and Compound-Vinyl-based powder or premixed joint compound. applied In' <br />coats to jOints and screw heads; paper tape 2 in. wide. embedded in first layer of com~ <br />over all joints. '!i. <br />.Bearing the Ul Classification Marking <br /> <br />Design No. U469 <br />Assembly Rating-1 Hour <br />Non-Bearing Wall <br /> <br /> <br />24" <br /> <br />(600rnrn) <br /> <br />. ............................................. <br />... .............................................. ............................ ............................................. <br />.............................................. ............................ ............... ............................................. <br /> <br />.- :...-.. <br /> <br />. -. <br /> <br />CEILING <br /> <br /> <br />HaRZ. SECTION <br /> <br />',. <br />, <br />1. Floor and Ceiling Runners-"J" - shaped. 2-1/2 in. wide with unequal legs of 1 in. Ind'~.li <br />fabricated from 24 MSG galv steel. Runners attached to structural supports wkh steelfafti <br />ers located not greater than 2 in. from ends and not greater than 24 in. OC. <br />2. Steel Stud&-"C-H" shaped studs. 2-1/2 in. wide by 1-1/2 in. deep. fabricated from 26 <br />galv steel. spaced 24 in. or 600 mm OC. Vertically restrained walls require studs to be'c . . <br />8 in. less than floor-to-ceiling height.,! <br />3. Gypsum Wallboardo-1 in. thick gypsum wallboard liner panels. supplied in nominal 24." <br />600 mm widths. Vertical edges inserted in "H" shaped section of "C-H" studs. F.... edg <br />end panels attached to long leg of "J'" runners with 1-5/8 in. long Type 5 self-drilJing, HIf <br />ping bugle head steel screws spaced not greater than 12 in. OC.;: <br />Canadian Gypsum Co.-Type SLX. <br />United States Gypsum Co.-Type SLX <br />4. Gypsum Wallboardo-5/8'in. thick. 4 ft or 1200 mm wide. applied vertically and <br />studs with 1 in. long Type 5 steel screws spaced 12 in. OC along the edges and in <br />of the boards. <br />Canadian Gypsum Co.-Type C <br />Domtar Gypsum Inc.-Type 5. <br />Georgia.Pacific Corp.. Gypsum Div.-Type GPFS-C. <br />Pabco Gypsum Co.-Type C or PG-C. <br />United Stat.. Gypsum Co.-Type C. IP-X2 or WRC. . <br />5. Batts and Blanketa.~ineral wool batts partially or completely filling stiicl <br />USG Intario~ , ~ <br />United State. Gypsum Co. . <br />oBearing the Ul Classification Marking <br /> <br />LOOK FOR MARK ON PRODUCT <br /> <br />-.: <br />1. Stl <br />ed <br />the <br />2. Fk <br />es, <br />0.< <br />3. Mi <br />an. <br />in. <br />an, <br />0.< <br />SUI <br /> <br />4. Ba <br />or <br /> <br />.Bearir <br /> <br />_1,( <br /> <br />-1:',,',":\ <br /> <br />'-. <br />