|
<br />
<br />-
<br />. .
<br />
<br />
<br />,green wire spliced to the bus and connected to each Pinspotter~:J"h;r~P!~~',~npectiqt'must
<br />be made using a split bolt and must be taped to prevent it fromcorning,in~nUl~with,.any
<br />other ground point. , The connection to the pinspotter is made to ,the, f(arne'o.f..#1.ernachine
<br />and the contaCt point must be bare metal (scrape off paint). . """,>)};"j;~:;;' '
<br />
<br />. ...
<br />
<br />The ground busses must be run to the incoming power ground and may not be' spU~cJ with,
<br />make contact with, or be connected to any other ground before reaching the, ground poInt
<br />
<br />. s~. .s':'t~,:t~2i\t{i'
<br />
<br />. t".c'
<br />
<br />,,' '-" ,'~. .-}- . .,_:,;, \t,:~~...
<br />.~, ". ;' ,.\ .~, ;,~' -:; ,
<br />
<br />*',; FIRST PREFERENCE
<br />';-'"':i:t;,;>: ^'A.,;,,:- ~
<br />
<br />,: ,';/
<br />. Connection must be made to the main entrance panel ground terrninalblo.,~Jf,~ndi-
<br />tions permit ' " ' ":'
<br />
<br />.
<br />
<br />
<br />SECOND PREFERENCE
<br />
<br />Connection may be made to the conduit at the main entrance
<br />the' panel is impossible.
<br />
<br />· ,"", 'THIRD PREFERENCE
<br />
<br />'Connection may"be made to a water pipe only if the first or second r:nethod'a~epo~
<br />feasible. The connection should be made as close as possibleto.theexit point of
<br />the water pipe from the building. ", ',",(
<br />
<br />NOTE: ,See appendix for grounding diagram.
<br />
<br />
<br />Th~ 'length of the, ground buss is restrictive as follows:
<br />
<br />(1)
<br />
<br />If thf! total length of the buss is 200 feet or less use a number 6 AW~\VireJor t!n~re
<br />buss.'" ' ,,' ,. " "/:;,,;;,~,,:,,,., ;..
<br />
<br />(2)
<br />
<br />, ,If the total length of the buss is 200 feet to 400 feet use two sections.U~e,number
<br />'4~ WG wire for first section from the ground connection tq the first unitaod u~e
<br />number 6 A WG wire for the remainder.
<br />
<br />
<br />
<br />'::","-,,:,
<br />/:":.-.
<br />
<br />;-",-
<br />. '2.7SURGE SUPPRESSORS INSTALLATION ,.' '~,',!,
<br />
<br />~;'fr;=:~;~;: ~dtere;fn=n::~=r::~~if!~~~~~.
<br />
<br />proprietor'~ electrician. ,',.Installation instructions will be provided withsuppressoii:~~"";'~i,r~i'c,
<br />
<br />, .~ '-. . : -', '. " : . . ":"':!>.':~':: ,:~:..:."" ~~> - ;.'~::':,,-::~:{,~,~:';':~::2:;,'::~_)'<:" "';::":':!{/;' '
<br />~ ,~- je;' '.,
<br />_~>.'.:,k '
<br />
<br />2.8'; GENERAL POWER REQUIREMENTS
<br />
<br /><:" .,,:!~' ; c ~ _ ,,' _.' '"
<br />,J . '~ . ,;_ <):'-,::"J~'~\::,'c~
<br />" "':>,:",\< ; > -~'~.,: "/-'; ,",:;;;">':;!,;';-y:,(-:,.:: ';;':'.:
<br />Ap.,tF requires thafthe incoming AC power supplied to the>automaticsC()riOg equipm~nt: "
<br />meet several conditions. It must be single phase, and fall into one'of,th~twO rangesJi~ted
<br />below: ' ." "';.>w:;;j,':{,-'r,,'i;r.t.
<br />
<br />.-,.;- ',.,':-;/.
<br />
<br />
<br />Nominal Voltace !
<br />115 VAC
<br />230 VAC
<br />
<br />".. , - .~' '" . .
<br />
<br />Voltace Rance
<br />100 to 130 VAC
<br />205 to 250 VAC
<br />
<br />Freauencv
<br />47 ~ 63 Hz
<br />47 - 63 .
<br />
<br />.. . <'. - "'.:~'.;-,'
<br />
<br />.,.... "
<br />
<br />
<br />
<br />Page 7
<br />
<br />Pre-lnstallation Requirements - 2000/3000
<br />
<br />March 1993'.
<br />
|