|
<br />FLORIDA ENERGY EFFICIENCY CODE FOR BUILDING CONSTRUCTION
<br />FORM 600B-93 Residential Component Prescriptive Method B CENTRAL 4 5 6
<br />Department of Community Affairs
<br />
<br />
<br />OWNER:
<br />
<br />GENERAL DIRECTIONS
<br />1. New construction including additions which incorporates any of the following features cannot comply using this method: raised wood floors without continuous stem walls,
<br />steel stud walls, single assembly roof/ceiling construction, or skylights or other non-vertical roof glass.
<br />2. Choose one of the component packages "A" through "F" from Table 6B-1 by which you intend to comply with the Code. Circle the column of the package you have chosen.
<br />3. Fill in all the applicable spaces of the "To Be Installed" column on Table 6B-1 with the information requested. All "To Be Installed" values must be equal to or more efficient
<br />than the required levels.
<br />4. Complete page 1 based on the "To Be Installed" column information.
<br />5. Read "Minimum Requirements for All Packages", Table 6B-2 and check each box to indicate your intent to comply with all applicable items.
<br />6. Read, sign and date the "Prepared By" certification statement at the bottom of page 1. The owner or owner's agent must also sign and date the form.
<br />
<br />Please Print CK
<br />
<br />1. Compliance package chosen (A-F)
<br />2, New construction or addition
<br />3. Single family detached or Multifamily attached
<br />4. If Multifamily-No, of units covered by this submission
<br />5, If Multifamily, is this a worst case (yes / no)
<br />6, Conditioned floor area (sq. ft.)
<br />7. Predominant eave overhang (ft.)
<br />8, Porch overhang length (ft.)
<br />9, Glass area and type:
<br />a. Clear glass
<br />b. Tint, film or solar screen
<br />10, Percentage of glass to floor area
<br />11, Floor type and insulation:
<br />a. Slab on grade (R-value)
<br />b. Wood, raised (R-value)
<br />c. Wood, common (R-value)
<br />d. Concrete, raised (R-value)
<br />e. Concrete, common (R-value)
<br />12, Wall type and insulation:
<br />a. Exterior:
<br />1. Masonry (Insulation R-value)
<br />2. Wood frame (Insulation R-value)
<br />b. Adjacent:
<br />1. Masonry (Insulation R-value)
<br />2. Wood frame (Insulation R-value)
<br />13, Ceiling type and insulation:
<br />a. Under attic (Insulation R-value)
<br />b. Single assembly (Insulation R-value)
<br />14, Cooling system
<br />(Types: central, room unit, package terminal A.C., none)
<br />
<br />1.
<br />2,
<br />3.
<br />4,
<br />5,
<br />6.
<br />7,
<br />8.
<br />
<br />A).u<- '
<br />/ \ .. (.r r
<br />-'; /t- (P '1-.
<br />
<br />/0 f.(C)
<br />.,
<br />~--
<br />'i(p '( if
<br />Single Pane
<br />sq. ft.
<br />sq. ft.
<br />Ii %
<br />
<br />Double Pane
<br />sq. ft.
<br />/11.. I sq. ft.
<br />
<br />9a.
<br />9b,
<br />10.
<br />
<br />11a.
<br />11b.
<br />11c.
<br />11d.
<br />11e.
<br />
<br />R=
<br />
<br />R= If
<br />R=
<br />
<br />R=
<br />
<br />R=
<br />
<br />sq. ft.
<br />/ Of{ l> sq. ft.
<br />sq. ft.
<br />sq. ft.
<br />sq. ft.
<br />
<br />12a-1 R= sq. ft.
<br />12a-2 R= II sq. ft.
<br />12b-1 R= sq. ft.
<br />12b-2 R= 1/ jet0 sq. ft.
<br /> ,
<br />13a. R= J() _/ C' l/ C, sq. ft.
<br />13b. R= sq. ft.
<br />
<br />Type: ( I/' 1'-''7' &1 Ii /
<br />SEERlEER: ---L!2 ", C
<br />Type: IjfF/I fVtt/
<br />HSPF/COP/AFUE: '7,- c 0
<br />Type: L /p c-f
<br />EF:
<br />
<br />14,
<br />
<br />15, Heating system:
<br />(Types: heat pump, elec. strip, nat. gas, L.P. gas, room or PTAC, none)
<br />16. Hot water system:
<br />(Types: ele<;., nat. gas, L.P. gas, solar, heat rec., ded. heat pump, other, none)
<br />
<br />15,
<br />
<br />16,
<br />
<br />
<br />-1-
<br />
|