|
<br />200 Photoelectric Smoke Detector
<br />
<br />~
<br />
<br />By H...yw.1I PruI.clllM1 S.rvlces
<br />
<br />Honeyw{.n
<br />
<br />Features
<br />
<br />Selectable Alarm Current- (2-Wire Model)
<br />Allows a choice of 25 ma, 50. ma, or 90. ma,
<br />
<br />135F Heat Sensor Option-
<br />Activates alarm when temperature at detector reaches 135F
<br />Specify HD option when ordering,
<br />
<br />Separate Detector and Base Design-
<br />Permits the same detector to be used with both 2- and 4-wire
<br />bases, Features quick-disconnect ease and positive-lock
<br />assembly stability,
<br />
<br />Universal Mounting-
<br />Allows connection to single and double gang outlet and switch
<br />boxes, as well as standard 4" square and octagonal type
<br />boxes, May also be connected to surface mounted Wiremold
<br />type raceways,
<br />
<br />Dust Proof Protection-
<br />Sealed electronics permit drafty "plenum" ceiling applications
<br />without concern for nuisance alarms due to "pull-through" dust
<br />caused by pressure differentials,
<br />
<br />Tamper Protection-
<br />No concern about forgetting to replace the detector. In/Out wiring
<br />results in a fail-safe trouble signal with detector removal.
<br />
<br />Vandal Protection-
<br />Detector securely latches to base with two point tie-down,
<br />
<br />Specifications
<br />
<br />Models-
<br />20.0. Detector only (requires base),
<br />2o.o.HD Detector with 1350F Heat Sensor (requires base),
<br />MB2o.o.-2W Base, 2-Wire,
<br />MB2o.o.-4W Base, 4-Wire.
<br />2o.o.-2W 20.0. with MB2o.o.-2W Base,
<br />2o.o.-4W 20.0. with MB2o.o.-4W Base.
<br />2o.o.HD-2W 2o.o.HD with MB2o.o.-2W Base.
<br />2o.o.HD-4W 2o.o.HO with MB2o.o.-4W Base.
<br />
<br />Accessories-
<br />EOL2o.o. End-Of-Line Module for 4 Wire Systems,
<br />T2o.o. Ceiling Disconnect Tool
<br />
<br />Environmental Limits-
<br />Temperature: +320F to +12o.oF (+o.oC to +490C) Tested, +320F
<br />to +1o.o.oF (+o.oC to +380C) Normal Operating,
<br />Humidity: 0. to 95% RH; Non-condensing, Withstands Humidity
<br />Shock testing,
<br />
<br />Electrical Requirements-
<br />Voltage: 10. to 27 VOC
<br />
<br />Maximum RMS Ripple: Less than 25% of DC Input
<br />Standby Current: 25 micro-amps (u a), Max.
<br />Alarm Current: 2-Wire = Selectable 25, 50. or 90. ma depending
<br />on panel used, 4-Wire = 25 ma @ 12 VDC 36 ma @ 24
<br />VDC
<br />Start-Up Current: 20.0. micro-amps (u a), max, for 0.3 sec, (after
<br />initial power applied,)
<br />
<br />Sensitivity-
<br />Factory calibrated for 3% gray smoke obscuration,
<br />
<br />Alarm Condition-
<br />2-Wire: SCR switch, Selectable alarm current
<br />4-Wire: Mechanical relay Dry contacts rated 30. VDC, 2A,
<br />resistive load,
<br />
<br />Infrared Source Pulse Format-
<br />30.0. micro-second wide pulse every two seconds, At 3%
<br />threshold obscuration, pulse speed increases four times (4X) ,
<br />Alarm Initiated after 5 consecutive pulses if still above
<br />threshold, Automatic pulse count reset if obscuration drops
<br />below 3% threshold before alarm initiated,
<br />
<br />Power and Alarm Indicators-
<br />Two annunciator LEOs located close to the base on opposite
<br />sides of the detector are standard, LED1 flashes briefly every
<br />two seconds to verify normal operation of internal infrared
<br />source, LED2 normally OFF, but latches ON in the event of an
<br />alarm; standard reset with power interrupt
<br />
<br />Remote Alarm Indicator-
<br />Optional remote alarm LED circuit available. Up to 10.0. ma
<br />allowed in remote circuit using 2-Wire base; 80. ma with 4-Wire
<br />base,
<br />
<br />Full Function Test-
<br />Individual detector alarm using a magnet in conjunction with a
<br />built-in internal reed switch,
<br />Multiple detector alarm using optional N.o switch installed
<br />between terminal 'I" and ground at any base,
<br />
<br />Radio Frequency Interference-
<br />No alarm or set-up on critical frequencies in the range from 26 to
<br />90.0. MHz using a 10. Watt transmitter located 4ft, (1,2 m) from
<br />the unit or attached wiring under test
<br />
<br />Terminal Designations-
<br />2-Wire Class B, 4-Wire Class B,
<br />
<br />Approvals-
<br />Underwriters Laboratories (U,L,) Listed
<br />State of California Fire Marshall (CFM) Approved
<br />
<br />Honeywell
<br />
<br />HELPING YOU CONTROL YOUR WORLD
<br />
<br />@ Honeywell, lnc 1989
<br />
<br />PROTECTION SERVICES DIVISION
<br />
<br />Honeywell Plaza
<br />Minneapolis, Minnesota 55408
<br />
<br />I n Canada
<br />100 Montcalm Blvd N
<br />Candiac, Quebec
<br />J5R 1 B7
<br />
<br />Providing nationwide U L listed central station alarm service
<br />
<br />56-32144/89 Printed In U,S.A
<br />
|