Laserfiche WebLink
<br />Table 5.1: Allowable Spans for Industry Standard Pans for Roof Overs <br />Industry Standard Pan Sections <br />Aluminum Alloy 3105 H-14 or H-25 <br />.,,-------- / ~ <br />1-1/4"x 12" x 0.026" Panels <br />verhan <br />NONE <br /> <br />~~ <br />110 M.P.H. <br />120 M.P.H. , <br />, 125M.P,H. I <br />. 140JIt1.P.H. i <br /> <br />Load <br />17 <br />20 <br />23 <br />26 <br />32 <br /> <br />ROOF OVER SYSTEMS <br /> <br />SECTION 5 <br /> <br /> <br />1-1/4" x 12" x 0.032" Panels <br /> <br />7'-8" <br />7'-1 " 7'-4" <br />6'-7" 6'-10" <br />6'_2" 6'-6" <br />5'_7" 5'-11" <br /> <br />Condition Wind <br />2'-0" 3'-0" Region, <br />8'-7" g'-g" 102 M.P.H. <br />8'-1" 9'-3" 110 M.P.H. <br />7'-8" 8'-11".120 M.P.H. <br />7'-4" 8'-7": 12~ M.P.H. i <br />, 6'-10" . 8'-2" :140 M.P.H.! <br /> <br />()vertlC!l1_g. Con.clition <br />NONE. 1'-Q" . 2'-0" 3'-()" <br />8'-11" 9'-2" 9'-10" 10'-10" <br />8'_3" 8'-6" 9'-2" 1 0'-3" <br />7'-g" 7'-11" 8'_8" g'-g" <br />7'-3" ,. 7'-.f5~' , 8'-4" , g'-.5" <br />6'_7" i 6'-10" i 7'-8" : 8'-11" I <br /> <br />Applied, <br />Load <br />17 <br />20 <br />23 <br />26 <br />32 <br /> <br />- - -- ~ <br />1-3/4" x 12" x 0.032" Panels <br />- .- . <br />Overhang.Condition Wind; Applied I ....9":e.':.tl~.g.Con~ition <br />NONE 1'-0" 2'-0" 3'-0" I R.e.9.io.n. Load. NONE: 1'-Q" . 2'-0" 3'-0" <br />8'_0" '. 8'-3" . 8'-11" , 10'-9" 1 ()~ M.P .H.j 17 9'-5" i g'-T' 10'-3". 11 '_2" <br />7'-5" 7'-8" 8'-5" 9'-6" 110 M.P.H. 20 8'-8" 8'-11" 9'-6" 10'-6" <br />. ... , ... __.d I __ <br />6'-11" 7'-2" 7'-11" g'-.2", 1?Q M.F~.H. ; 23 8'-1". 8'_4" g'-O" 10'-1" <br />6'_6" 6'_9" 7'-7" 8'-10" 125 M.P.H. I 26 7'-7'" 7'-10": 8'_7" 9'-8" <br />5'-10" 6'-2" 7'-1'" 8'-4'; '140 M.P.H. ~ 32 . 6'-1()" 1 7'-?~'l7'-11": ~:r-1" ; <br /> <br />1-3/4" x 12" x 0.026" Panels <br /> <br />Wind <br />Region <br />102 M.P.H. , <br />11Q M.P.H. I <br />,1 ?QJv'I.P .1-1. I <br />125 M.P.H. <br />140 M.P.H. <br /> <br />Applied <br />Load <br />17 <br />2.0 <br />23 <br />26 <br />32 <br /> <br />Total pan LENGTH = Above "SPAN" + Length of overhang or span length of panel between anchor points. <br />Z-Clip anchors can be added to achieve longer spans and are recommended to eliminate pan rumble. <br /> <br />ALL WORK S"',.Lt. COMPLY Wrnf <br />PREY AIUNG COOES. STANDARD <br />BUILDING. PLUMBING. MECHANICAL. <br />N.E.c.. AND ALUMINUM <br /> <br />Lawrence E. Bennett, P.E. <br />ava:. ENGH:ER - DiEVELOPPENT CONSlL TANT <br />P.O. BOX 4368, SOl1Tll DA YTaNA, FL 32121 <br />TELEPHOIE (9Q.4) 767-4774' <br />FAX (904) 767-6556 <br /> <br />SEAL <br /> <br />PAGE <br /> <br />@ COPYRIGHT 1997 <br />NOT TO BE REPRODUCED N WHOLE OR N PART wrrnour rq; WRITTEN PERMSSION OF LAWRENCe E. BENETT, P.E. <br /> <br />101 <br />