Laserfiche WebLink
<br />SCREEN, VINYL & GLASS ROOMS <br /> <br /> <br />Load <br />Width <br /> <br />102 M.P.H. <br /> <br />36" <br />42" <br />48" <br />54" <br />60" <br />66" <br />72" <br />78" <br />84" <br />90" <br /> <br />19#'S . Ft. <br />12'-3" <br />11'-4" <br />10'-7" <br />9'-11" <br />9'-6" <br />9'.0" <br />8'-8" <br />8'.4" <br />7'-11" <br />7'-g" <br /> <br /> 2" x 3" x 0.050" Hollow Extrusion <br /> Wind Zone <br />Load 102 M.P.H. I 110 M.P.H. I 120 M.P.H. I 125 M.P.H. I 140 M.P.H. <br />Width Applied Load <br /> 19 # 'Sq. Ft. 23 # 'Sq. Ft. 26 # 'Sq. Ft. 29 # 'Sq, Ft. 36 # 'Sq. Ft. <br />36" 16'-10" 15'.3" 14'-4" 13'-7" 12'-3" <br />42" 15'-7" 14'.2" 13'-4" 12'-7" 11'-4" <br />48" 14'-7" 13'.3" 12'.5" 11'.9" 10'-7" <br />54" 13'-9" 12'-6" 11'-9" 11'-1" 9'-11" <br />60" 13'-0" 11'-10" 11'-2" 10'-6" 9'-6" <br />66" 12'-5" 11'-3" 10'.7" 10'-1" 9'-0" <br />72" 11'-11" 10'-10" 10'-2" g'-7" 8'-8" <br />78" 11'-5" 10'-5" 9'-9" 9'-3" 81-4" <br />84" 11'-0" 10'-0" 9'-5" 8'-11" 8'-0" <br />90" 10'-8" 9'-8" 9'-1" 8'-7" 7'-g" <br /> 2" x 4" x 0.050" Hollow Extrusion <br /> Wind Zone <br />Load 102 M,P.H. I 110 M.P.H. I 120 M.P,H. I 125 M.P.H. I 140 M.P.H. <br />Width Applied Load <br /> 19 # ISq. Ft. 23 # 'Sq. Ft. 26 # 'Sq. Ft. 29 # 'Sq. Ft. 36 # 'Sq. Ft. <br />36" 20'-9" 18'-11" 17'-g" 16'-10" 15'-1" <br />42" 19'-3" 17'-6" 16'-5" 15'-7" 13'-11" <br />48" 17'-11" 16'-4" 15'-5" 14'.7" 13'-1" <br />54" 16'-11" 15'-5" 14'.6" 13'-9" 12'-4" <br />60" 16'-1" 14'-8" 13'-g" 13'-0" 11'-8" <br />66" 15'.4" 13'-11" 13'-1" 12'.5" 11'-2" <br />72" 14'-8" 13'-4" 12'-7" 11'-11" 10'.8" <br />78" 14'-1" 12'-10" 12'-1" 11'-5" 10'-3" <br />84" 13'-7" 12'-4" 11'-8" 11'-0" 9'.11" <br />90" 13'-2" 11'-11" 11'-3" 10'-8" 9'.7" <br /> <br />Notes: <br />Glass Rooms' The addition of aluminum frame windows with glass panes that are designed <br />to 110M P H wind load requirements to the above upright sizes increases the strength so that <br />additional framing is not required. <br />Using screen panel width "W' (See typical glass room drawing.), select upright required from <br />the maximum height allowed for each extrusion. <br />Screen Splines on 3" side. extrusion turned with 3" side parallel to sole plate <br /> <br />Lawrence E. Bennett, P.E. <br />CIVIL ENGINEER - DEVELOPMENT CONSUL TANT <br />P.O. BOX 4368, SOUTH DAYTONA. FL32121 <br />TELEPHONE (904) 767-4774 <br />FAX (904) 767-6556 <br /> <br />@ COPYRIGHT 1999 <br />NOT TO BE REPRODUCED IN WHOLE OR IN PART WITHOUT THE WRITTEN PERMISSION OF LAWRENCE E. BENNETT, P-E. <br /> <br />SECTION 3 <br /> <br />SEAL <br /> <br />PAGE <br /> <br />93 <br />