|
<br />SECTION 3
<br />
<br />SCREEN, VINYL & GLASS ROOMS
<br />
<br />
<br />load
<br />Width
<br />
<br />6'...5"
<br />6.3
<br />
<br /> 2" x 2" x 0,044" Hall ow Extrusion
<br /> W Ind Zone
<br />load ~02 M,P:H:T TfOM,P,H.1 120 M.P,H. 130 M,P,H, I 140 M,P.H. I 150 M,P.H,
<br />Width ADI ,lie d Load
<br /> 8 illSa, FL 9 illSa, Ft. 10" ISq. Ft. 12 #/Sa. Fl. 15" ISo, Ft. 18" Ii , FL
<br />38" 10'-10" 10'-1" 9-3" 8'.6' 7 -9" 7'-
<br />42" 10'.0" 9'-4' 8 -7 7'.10" 7.2" 6'- 1"
<br />48" 9-5" 8-9" B-O" 7'-4" 6-9" 6-
<br />54" 8 .10~ B'.3' 7 -7" B -11" 6'-4" 6-
<br />60 0'-5" iQO 7'-2" 6.T" 6-0 -
<br />86" B'-O" 7.5 6. 0 6-3 5-9" -
<br />72" 7.B' 7- 6-7" 5'.11" 5'.6" -3
<br />.78" 7'-4' 8'. 0" 6-4" 5'-9" 5'.3" .0"
<br />84" 7.1' 6'- 6 -1" 5-T" 5 -1" -10
<br />90 6'.1 0" 8'-4" 5'- 0 5'-4" 4'.11 " .8"
<br />
<br />,
<br />--'
<br />
<br /> 2" x 2" X 0,055' Hall ow Extrusion
<br /> W nd Zone
<br />Load ~02 M,P,H,I 110 M.P,H, I 120 M,P,H, 130 M,P,H,I 140 M,P,H,I 150 M,P,H.
<br />Width ADI IlIe tI Load
<br /> BI /Sa. Ft. 9#TSa: Ft. 10" ISo. Ft. 12 " ISo, Ft. 15 " ISo, Ft. 18 " /Sa, Ft.
<br />38" 1'-10" 10-11" 10'-1 9-3" 8. :" 8-0"
<br />42 0'-11" 10 -2" g'-4" B-7 7- 0 7 -5"
<br />48" 0'.3 9.6" 8-9" 8'-0" 7'~ 8.11'
<br />M' 9'-8" B -11" B'.3" 7 -T" B. ," 6-7"
<br />60' 9'.2" 8'-6" 7'-10" 7'-2" 6- 6.3"
<br />66' 6'-9" B'-l" 7'.5" 6'-10" 6'.3 5-11"
<br />72" 8'-4" 7'.g" 7'-2" 6'-6" 5'-11 " 5'-8
<br />78" 8'.0" 7'.5" 6'.10" 6'-3" 5'-9" 5'-5"
<br />84" 7'.g" 7'-2" 6'-7" 6'.1" 5'.6" 5'.3"
<br />90' 7'.6" 6'.H" 6'.5" 5'.10" 5'-4" 5.1"
<br />
<br />Notes:
<br />Glass Rooms: The addition of aluminum frama windows with glass panes that are designed
<br />to 110 M.P.H. wind load requirements to the above upright sizes Increases the strength so
<br />that additional framing Is not raqulred.
<br />Screen Splines on 3" side. extrusion turned with 3" side parallel to sole plate,
<br />Example:
<br />Screen panel width "W" " 60":
<br />Maximum "H" for a 2" x 2" x 0,036" Hollow Extrusion = I 7'-7" I
<br />Using screen panel wldth'~ (See typical glass room drawing.), select upright height "H"
<br />required from the maximum halght allowed for each extrusion.
<br />
<br />Lawrence E. Bennett, P,E.
<br />CIVIL ENGINEER. DEVELOPMENT CONSUL TANT
<br />P,O. BOX 4368, SOUTH DAYTONA, FL 32121
<br />TELEPHONE (9Il4) 767-4774
<br />FAX (904) 787-6556
<br />
<br />-)
<br />
<br />SEAL
<br />
<br />PAGE
<br />
<br />3-20
<br />
<br />@ COPYRIGHT 2000
<br />NOT TO BE REPRODUCED IN WHOLE OR IN PART WITHOUT THE WRITTEN PERMISSION OF LAWRENCE E. BENNETT, P.E,
<br />
|