03-1876 - Laserfiche WebLink

Browse Search

1. SPEC IAL CIRCUMSTANCES: If the following cOndnlons oceu r - STO PI Contact Oliver Techn%gie s at 1-800-284-7437: a) Pier height exceeds 48~ b) Roof eaves exceed 16~ c) Sidewall height exceed 96' d) Roof Pftch 5/12 or greater e) Location Is wfth in 1500 feet of COast Oliver Technologies, Inc. FLORIDA INSTALLATION INSTRUCTIONS FOR THE MO EL 1 01 S R S LL STEEL FOUNDATION SYSTEM MODEL 1101 (STEPS 1-15) MODEL 1101-L LONGITUDINAL ONLY: FOLLOW INSTRUCTIONS 1-11 . 2. Remove weeds and debris in an approximate two foot square to expose finn soil for each ground pan (C) . 3. Piace ground pan (C) directly below chassis I-beam. Press or drive pan finnly Into soil until flush wfth or below SOil. SPECIAL NOTE: The longftudinal cross brace system serves as a pier under the home and should be loaded as any other pier. it Is recommended that after leveling piers, and one-half Inch (112') before home is lowered completely on to piers, complete items 4 through 10 below. INSTALLATION OF GROUND PAN INSTALLATION OF LONGITUDINAL CROSSBRACE SYSTEM NOTE: IF INSTALUNG THE MODEL # 1101-L LONGITUDINAL ONLY, A MINIMUM OF 2 SYSTEMS PER FLOOR SECTION IS REQUIRED, AND ALL SIDEWALL ANCHORS SPACED AT 5' 4". FOUR FOOT (4') GROUND ANCHOR MAY BE USED EXCEPT WHERE MANUFACTURERS SPECIFY A DIFFERENCE. 4. Select the COrrect square lube brace (E) length for set - up (pier) height at support location. (the lB' tube is always used as the bottom part of the longitudinal arm). 1.25" ADJUSTABLE Tube Length 1.50" ADJUSTABLE Tube Length :;~iHi.lr_EfNiJt.. '.;-"-~.';:e:biffl!4~4d:i!i}.kt:"WK 32" 18" 54" 5. Install (l)ofthe 1.50' square tube (E (lB- tube)) Into each 'U' bracket (0), insert carriage bohs and ieave nuts loose for final adjustment. 6. Place I-beam connector (F) loosley on the bottom flange of the !-beam. Tum COn nectar so thatthe tube connector braCket is off center on same side as ground pan 'U' brackel (0) for other en.d of tube so that tubes will cross. 7. Slide the selected 1.25' lube (E) into a 1.S0'lube (E) and attaCh to I-beam connector (F) and fasten loosely with bolt and nut. B. Repeal steps.s through 7 to creale the crossed 'X' pattem of the square tubes lOOSely in place. NOTE: The angle is not to exceed 45 degree and not below 40 degrees. 9. Install bractng bolls and plates (G) In the horizonlal direction only, around both square tubes where they cross. Put nuts on bolt ends and tighten, IMPORTANT: Do not crush tube. 10. After aU bohs are tlghlened, secure 1.25' and 1.50' tubes using four(4) 1/4"-14 x 314" sell-tapping screws in pre- drilled holes. 11. InstaU remaining vertical tie-<lown straps and 4' ground anchors per home manufacturer's Instructions. All loads in excess Of3,1S0 pounds at shear walls, COlumns, and centertine, must have five foot (5) anchors Installed regardless of Soil Conditions, per the state of Florida. . 18" fNSTALLA ON OF LATERAL TELESCOPING TRANSVERSE ARM SYSTEM NOTE: THE MODEL 1101 (LONGITUDINAL & LATERAL PROJECTION) ELIMINATES THE NEED FOR ALL STABILIZER PLATES & FRAME TIES 12. Select the correct square tube brace (Ii) length for set-up lateral transverse at support location. The lengths Come in ei/her 60' or 72' lengths. (Wdh the 1.50" lube as the b01tom tube, and the 1.25" lube as the Inserted lube.) 13. tnstall the 1.50 transverse brace (Ii) to the ground pan connector (0) wllh boh and nut. 14. Slide 1.25' transverse brace Into the 1.50' brace and attach 10 adjacent I-beam connector ( , ) wfth bolt and nut. 15. SeCUre 1.50' transverse ann to 1.25' transverse ann using four (4) 1/4" _ 14 x 3/4' self-tapping screws in pre-drilled holes.