03-2129 - Laserfiche WebLink

Browse Search

Options Panel Operation Operators' Interface Control of the panel's operation is both simple and intuitive. While the LEOs and optional LCD are visible with the panel door closed, the door and bezel block access to the controls. With the door open the following controls are available: Reset - used to reset the panel; Signal Silence and Drill- used to silence notification appliances or activate the drill function; Panel Silence -silences the buzzer on the panel and the remote trouble unit; Remote Disconnect-disables the DACT, or, if no DACT installed, disables the panel's alarm relay; Walk Test -activates the panel's silent and audible walk test mode. Thefollowing system LEOs display the panel's status: Alarm - panel is in the alarm state; Trouble - panel is in the trouble state; Supervisory- panel is in the supervisory state; Power - indicates the status ofthe AC power source; . Disable - indicates when any IDC, NAC, relay or the DACT are disabled; Annunciator Trouble - indicates trouble on the remote annunciator bus; Battery Trouble - indicates battery or charging problems; Ground Fault - indicates a short between any panel circuit and ground; Walk Test - indicates that one or more IOCs are in the walk test mode; Alarms Silenced - indicates thatthe panel is in the alarm state with one or more NACs silenced. Off-premise communication A fully integrated FkeShield DACT/dialer is available for reporting events to a monitoring facility. The DACT also supports uploading or downloading of system configuration,statusand event history. The OACT is programmable for either single or dual line opera- tion.ltalso supports split and dual reporting for two digital alarm receivers. The DACT brings additional features to the panel including a 32-character alphanumeric LCD displav, local or remote PC programming and an event history Jog. Modules are also available for City Tie (CTM4.7) and Reverse Polarity (RPM) connections. Remote Annunciators and Relays The serial bus standard on all FireShield models is another installation time-saver. This circuit allows the connection of Remote System Indicators (FSRSI), Remote Zone Indicators (FSRZI-A) and Remote Relay Modules (FSRRM) over a four-wire (data and power) circuit Annunciator and relay modules can be installed up to 1,000 feet from the panel on 18-gauge wire. FS1004 Application FireShield provides smoke and fire detectio n, occupant notification and off-premises signaling for small- to medium-sized buildings. Each IDC can be configured for either Class B or Class A operation and one of eight operating modes: Alarm -without smoke detector verification; Alarm - with smoke detector verification, and instant activation of contact devices; Waterflow Alarm - no retard; Waterflow Alarm - with 15 seco nd retard; Combination Waterflow (no retard) and Supervi- FS502 sory; Combination Waterflow (retard) and Supervisory; Supervisory (Latching); Monitor -for monitoring devices other than alarm or supervisory such as fire doors or tire dampers. NACs may also be configured for either Class B or Class A operation. Additionally, NACs can be individually configured for one ofthree outputs. These are Genesis, Continuous or Temporal. The Genesis selection allows ind ependent horn control over two wires and provides precision synchroniza- tion for Genesis devices, all withoutthe need for a Genesis Signal Master accessory. When configured for Genesis notification appliances, FireShield's Alarm Silence function will silence connected Genesis audible appliances but Genesis strobes will remain active until the panel is reset. When Genesis Mode is selected, both the horns and strobes on Genesis and Enhanced Integrity notifica- ,i' tion appliances will be synchronized across all NAGs. Each IDC has a disable switch and three LEDs: Alarm -red - indicates that the IDC is in the alarm state; Trouble - yeffow - indicates that the IDC is in the tro uble state oris disabled (when flashing); Superviso rylMonitor -yellow - ind icates that the IDC is in the supervisory state orthe monitor state (when flashing). Each NAC also has a disable switch and a troublel disable LED. Status indication with the DACT IDia/er installed The dialer's LCD display provides two lines x '6 characters oftert For programming, the top line displays the programming step and the lower line displays the selected option. Page 2 of e laaue 2 EDWARDS SYSTEMS TECHNOLOGY literature Sh_t #85005-0118 Not 1'0 be used for installaTion purposes. For the most: current IIteratu.re end update. vlalt 'WW'W'...'t.net:;