03-2520 - Laserfiche WebLink

Browse Search

. . Electrical Specifications Primary AC: 120 VRMS @ 50/60 hz, 2.75A Total Accessory Load: 6 A @ 24 VDC 6 Amps @ 24 VOC of power-limited notification power Standby Current: 206 mA Alarm Current: 356 mA Battery Charging Capacity: Up to 33 Ah Notification Appliance Circuits Four programmable circuits which can be programmed individually as: Notification Circuits: 3 amps of power-limited power per circuit at 24 VOC. Auxiliary Power Circuits: Telephone Requirements 3 amps of power-limited power per circuit at 24 VDC. FCC Part 15 and Part 68 approved RJ31X (two required) Type of Jack: Accessory Product Information RA-100 Remote Annunciator-80 character backlit LCD display with a built-in keypad. The system can be fully programmed and operated from any remote annunciator. The IFP-100 can support up to 8 RA-100 remote annunciators per system. 5824 Serial Parallel Module-The 5824 is a serial/parallel interface that is used to connect a serial or parallel computer printer to the IFP-100 control panel via the RS-485 system bus. Up to two 5824 modules can be used with a system. 5880 LEDllnput-Output Module-The 5880 provides 40 programmable LED outputs and eight supervised dry contact inputs. Up to eight 5880 modules can be used on the IFP- 100's SBUS. 5865-3 and 5865-4 LED Fire Annunciators-The 5865 series annunciators provide a visual indication of the current state of the zone inputs on the control panel.Up to 8 Model 5865s can be used on the IFP-100's SBUS. Each 5865 has 30 programmable LED outputs-15 red and 15 yellow. The 5865s come with a piezo sounder which gives an audible indication during alarms, troubles and supervisory troubles. 5883- The 5883 Relay Interface Board provides 10 general purpose Form C relays that can be used to control any device that requires a dry contact closure. SD505-APS-Analog addressable photoelectric smoke detector. SD505-AIS-Analog addressable ionization smoke detector. SD505-AHS-Analog addressable heat sensor. SD505-6AB-Six inch base designed for use with detector head models S0505-APS, S0505-AIS, and S050S-AHS. SD505-4AB-Four inch base designed for use with detector head models S0505-APS, SD505-AIS, and SD505-AHS. SD505-6IB-6 inch isolator base. The S0505-61B isolates a short circuit wiring fault on a Style 7 (Class A) SLC loop. SD505-6RB-6 inch relay base. The S0505-6RB adds a programmable relay output to any detector on the SLC Loop. SD505-6S8-6 inch sounder base adds an audible output function to Farenhyt analog addressable detectors. SD505-SDM- Two-wire smoke detector module allows you to assign an address to a loop of conventional detection devices. SD500-PS- The SD500-PS is a single action addressable fire pull station featuring rugged metal construction with visible LED. SD505-ADHR/DTS- The SD505-ADHR analog addressable duct smoke detector with built-in relay module detects products of combustion present in air moving through an HVAC system. The S0505-AoHR is compatible with the S0505-0TS, which provides remote annunciation and testing capabilities for the S0505-AOHR. SD505-ADH-Analog addressable duct housing. Unit ships with an attached detector base which is compatible with the S0505-AIS or S0505-APS smoke detectors. (Detector and sampling tubes ordered separately.) SD500-AIM-Addressable input module used to connect pull stations, water flow switches, and other applications requiring dry contact alarm initiation devices. The AIM mounts into a 4" square electrical box. SD500-LED-An LED driver capable of driving 80 LEOs through the SLC loop. Up to 40 S0500-LEos can be used per system. SD500-MIM-Mlni Addressable input module used to connect pull stations, water flow switches, and other applications requiring dry contact alarm initiation devices. The MIM mounts into a single gang electrical box. SD500-L1M-Addressable Line isolator module.that isolates a short circuit wiring fault on a Style 7 (Class A) SLC loop. SD500-ARM-Addressable Relay Module allows you to control a normally open or closed device such as; elevator recall, door closing, fan operations, and auxiliary notification. Relay can be mapped to any zone condition. The ARM has two Form C contacts and mounts into a 4" square electrical box. SD500-ANM-Addressable Notification Module. The S0500- ANM is an supervised addressable notification device that provides an additional circuit on the IFP-100 SLC 100p.The S0500-ANM can be programmed to use any of the IFP-100 notification patterns. 5496 Intelligent Power Module-The Model 5496 is a 6 amp. notification power expander that provides four additional power-limited notification appliance circuit outputs. RPS-1000 Intelligent Power Module--Adds 5 amps of output power, six programmable Flexput™ I/O circuits and 2 Form C relay circuits to the system. Up to eight RPS-1000 modules can be used on the FACP. 5650 Down load Software-User-friendly software for remote programming of the IFP-100. The software is compatible with Window™ 95, Windows™ 98, and Windows™ NT. 5670 IntelliView Facility Management Software-End-user software allows viewing of detector status and event history via modem or direct connect. ~ SILENT I<NIGHT '" 7550 Meridian Circle, Maple Grove, MN 55369-4927 1-800-446-6444 or in Minnesota 763-493-6435 FAX: 763-493-6475 World Wide Web: http://www.farenhyt.com .~~~~=~~ .,. Made in the U.S.A. ("'.~ .~!!J!