Laserfiche WebLink
<br />OEM RELEASEJBRACKET ASSEMBLY <br />(FOR OEM IN-CABlNET USE ONLY) <br /> <br />The OEM Regulated Mechanical ReleaselBracket Assembly, Part <br />No. 79493, contains the same regulated release mechanism as <br />the standard ANSUL AUTO MAN Regulated Release Assembly. <br />The OEM Regulated Electrical Release/Bracket Assembly, Part <br />No. 418054, is identical to the mechanical version except it con- <br />tains a factory installed 120 VAC solenoid and electrical switch. <br />~ These releaseJbracket assemblies must be installed in a suitable <br />equipment enclosure either horizontally or vertically. They contain <br />all the necessary mounting and conduit holes needed to fully <br />install the assembly. The agent tank is installed separately and <br />~ need not be bracketed once it is piped and filled. NOTE: OEM <br />I Release/Bracket Assembly must be installed high enough in cabi- <br />~ net so that there is sufficient room to install and remove cartridge. <br /> <br />~ <br /> <br /> <br />SHIPPING WT. <br />10 LB. (5 kg) <br /> <br />MOUNTING <br />~ BRACKET <br /> <br />" ' <br /> <br />FIGURE 8 <br />000'44 <br /> <br />OEM REGULATED ACTUATOR ASSEMBLY <br />~ <br />The OEM Regulated Actuator Assembly, Part No. 418691, <br />includes the regulator, pneumatic actuator, expellant gas hose and <br />OEM bracket. Also available is an OEM Regulated Actuator <br />Assembly with all the above mentioned components except for the <br />bracket. This assembly is Part No. 418522. <br /> <br /> <br />SHIPPING WT. 4 LB. (2 kg) <br /> <br />~ <br /> <br />FIGURE 9 <br />00222S <br /> <br />SECTION 1\1 - SYSTEM COMPONENTS <br />UL EX. 3470 ULC CEx747 Page 3-3 <br />10-1-02 REV. 6 <br /> <br />TWO TANK ENCLOSURE ASSEMBLY <br /> <br />The Two Tank Enclosure Assembly, Part No. 429872, consists of <br />two expellant gas hoses, two grommets, and the mounting enclo- <br />sure. The assembly is used in 9 gallon systems. It can be coupled <br />with a 3-gallon regulated release assembly or a 3-gaIlon regulated <br />actuator assembly to give a total of 9 gallons of agent. Agent tanks <br />must be ordered separately. <br /> <br />The tank enclosure is designed to mount in a minil1M.lm amount of <br />space. <br /> <br /> <br />NOTE: AGENT TANK MUST BE <br />ORDERED SEPAAATElY <br /> <br />~ SHIPPING WT. <br />26 LBS. (12 kg) <br /> <br />FIGURE 10 <br />rKIZlT1 <br /> <br />24 VDC REGULATED RELEASE ASSEMBLY (ULC APPROVED <br />ONLY) <br /> <br />~ The 24 VDC Regulated Release Assembly, Part No. 429859, is <br />used where electric, thermostat detection is required via theuse of <br />a releasing control unit. This assembly consists of a 24 VDC <br />ANSUL AUTOMAN II-C regulated release mechanism, expellant <br />gas hose, and enclosure knockouts to facilitate installing actuation <br />piping, expellanl piping, detection system, and additional equip- <br />ment. Agent tank must be ordered separately. <br /> <br />The system can be actuated automatically or manually. Automatic <br />actuation occurs when the control panel receives a signal from the <br />detection circuit. The panel then sends an electrical signal to the <br />24 VDC regulated release, causing it to actuate. When actuation <br />occurs, the gas cartridge is punctured, pressurizing the agent tank <br />and discharging the agent through the distribution piping. Manual <br />actuation of the system occurs when personnel pull on the remote <br />manual pull station pull ring. <br /> <br />:i <br /> <br />~ <br /> <br /> <br />SHIPPING WT. <br />34 LB. (15 kg) <br /> <br />NOTE: AGENT TANK MUST BE <br />ORDERED SEPARATELY <br /> <br />FIGURE 11 <br />....,. <br />