|
<br />gradient, load intensity and erosion characteristics of slope
<br />material.
<br />
<br />1805.4 Footings. Footings shall be designed and constructed in
<br />accordance with Sections 1805.4, I through 1805.4.6.
<br />
<br />1805.4.1 Design, Footings shall be so designed that the.
<br />allowable bearing capacity of the soil is not exceeded. and
<br />that differential settlement is minimized. The minimum
<br />width of footings shall be 12 inches (305 mm).
<br />
<br />Footings in areas with expansive soils shall be designed
<br />in accordance with the provisions of Section 1805.8.
<br />
<br />1805.4.1.1 Design loads. Footings shall be designed for
<br />the most unfavorable effects due to the combinations of
<br />loads specified in Section 1605,3. The dead load shall in-
<br />clude the weight of foundations, footings and overlying
<br />fill. Reduced live loads, as specified in Section 1607,9.
<br />are pennitted to be used in designing footings,
<br />
<br />1805.4,1.2 Vibratory loads. Where machinery opera-
<br />tions or other vibrations are transmitted through the
<br />foundation, consideration shall be given in the footing
<br />design to prevent detrimental disturbances of the soil.
<br />
<br />1805.4.2 Concrete footings, The design. materials and con-
<br />struction of concrete footings shall comply with Sections
<br />1805.4,2, I through 1805.4,2.6 and the provisions of Chap-
<br />ter 19.
<br />
<br />Exception: Where a specific design is not provided. con-
<br />crete footings supporting walls of light-frame construc-
<br />tion are pennitted to be designed in accordance with
<br />Table 1805.4,2,
<br />
<br />1805.4.2.1 Concrete strength. Concrete in footings
<br />shall have a specified compressive strength if I c) of not
<br />less than 2,500 pounds per square inch (psi) (17237 kPa)
<br />at 28 days,
<br />
<br />1805.4.2.2 Reserved.
<br />
<br />SOILS AND FOUNDATIONS
<br />
<br />1805,4,2,3 Plain concrete footings. The edge thickness
<br />of plain concrete footings supporting walls of other than
<br />light-frllJTle construction shall not be less than is Inches
<br />(203 mrn) where placed on soil.
<br />
<br />Exception: For plain concrete footings supporting
<br />Group R-3 occupancies. the edge thickness is permit-
<br />ted to be 6 inches (152 mm), provided that the footing
<br />does not extend beyond a distance greater than the
<br />thickness of the footing on either side of the supported
<br />wall.
<br />
<br />1805,4,2,4 Placement of concrete. Concrete footings
<br />shall nC!,t be placed through water unless a tremie or otber
<br />method approved by the building official is used. Where
<br />placed under or in the presence of water, the concrete
<br />shall be deposited by approved means to ensure mini-
<br />mum segregation of the mix and negligible turbulence of
<br />the water,
<br />
<br />1805,4,2,5 Protection of concrete. Concrete footings
<br />shall be protected from freezing during depositing and for
<br />a period of not less than five days thereafter. Water shall
<br />not be allowed to flow through the deposited concrete.
<br />
<br />1805.4,2,6~orming of concrete. Concrete footings are
<br />perffiitted to be cast against the earth where, in the opin-
<br />iOD of the building official. soil conditions do not require
<br />forming. Where forming is required, it shall be in accor-
<br />dance with Chapter 6 ofACI 318.
<br />
<br />1805,4,3 Masonry-unit footings. The design, materials
<br />and construction of masonry-unit footings shall comply
<br />with Sections 1805.4.3.1 and 1805.4.3,2, and the provisions
<br />of Chapter 21,
<br />
<br />Exception: Where a specific design is not provided, mo,
<br />sonry-unit footings supporting walls of light-frame con-
<br />struction are permitted to be designed in accordance with
<br />Table 1805.4.2,
<br />
<br />1805,4,3,1 Dimensions, Masonry-unit footings shall be
<br />.Iaid in Type M or S mortar complying with Section
<br />
<br />II
<br />
<br />TABLE 1805.4.2
<br />FOOTINGS SUPPORTING WALLS OF WGHT.FRAME CONSTRUCTION-' b. c, d
<br />
<br />.. WIDTH 011. ,. I
<br /> THICKNESS OF
<br />NUMBER OF FLOORS FOOTING FOOTING
<br />SUPPORTED BY THE FOOTING' (Inoh..) (Inch..)
<br />I 12 6
<br />2 15 6
<br />3 18 gf
<br /> i
<br />
<br />II
<br />
<br />For SI: I inch = 25.4 mm, I foot = 304.8 mm.
<br />u. Depth of footings shall be in accordance with Section 1805,2,
<br />b. The ground under the floor is permitted to be excavated to the elevation of the top of the footing,
<br />c. Interior-stud-bearing walls are permitted to be supported by isolated footings, The footing width and length shall be twice the width shown in this lable. and fool-
<br />ings shall be spaced not more than 6 feel on center,
<br />II d. For thickness of foundation walls, see Section 1805.5,
<br />e. Footings are permitted to support aroofin addition to the stipulated number of floors, Footingssupporting roof only shall be as required for supporting one !loor
<br />r. Plain concrete foolings for Group R-3 occupancies are permitted to be 6 incites thick,
<br />
<br />FLORIDA BUILDING CODE - BUILDING
<br />
<br />18.5
<br />
|