07-7345 - Laserfiche WebLink

Browse Search

12/14/2007 FRI 15: 53 FAX 1 813 806 7190 ADT Security Services ~004/008 SpedrAlert Advance Specifications Arch.tf'ctJEngineer SpeCIfications General SpectrAlert Advance homs, strobes and horn/strobes shall mount to a standard 4 x 4 x l'h-lnch back box. 4-lnch octagon back box or double-gang back box. T\'VO-wire products shall also mount to a single-gang 2 x 4 x 17fs-inch back box. A universal mounting plate shall be used for mounting Celllng and wall products. The notification appliance circuit wlrlng shall terminate at the universal mounting plate. Also, 5pecrrAlert Advance products, when used with the Sync.Orcuit. Module accessory, shall be powered from a non-coded notification appliance circuit output and shall operate on a nominal 12 or 24 volts. When used with the Sync.Circuit Module, 12-volt rated notification appllan<e circuit outputs shall operate between nine and 175 volts: 24-vott rated notification appliance circuit outputs shall operate between 17 and 33 volts. Indoor SpectrAlert Advance products shall operate between 32 and 120 degrees Fahrenheit from a regulated OC, or full-wave rectified, unfiltered power supply. Strobes and horn/strobes shall have field-selectable candela senings includIng 15, 15/75,30, 75,95, 11 0, 115, 135, 150, 177, 185. Strobe "The strobe shall be a System Sensor Spec;trAlert Advance Model_llsted to UL 1971 and shall be approved for fire protective service. The strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances, nashing at 1 Hz over the strobe's entire operating voltage range. The strobe light shall consist of a xenon flash tube and associated lens/reflector systern HomlStrobe Combination TIle horn/strobe shall be a System Sensor SpectrAlen N:Nance Model_ listed to UL 1971 and UL 464 and shall be approved for fire protective service. TIle horn/strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with DIsabilities Act requirements for visible signaling appliances, flashing at 1 Hz over the strobe's entire operating voltage range. The strobe light shall consist of a xenon flash tube and assOCiated lens/reflector system. The hem shall have three audibility oprlons and an option to switch between a temporal three-pattern and a non-temporal (continuous) panern. These options are set by a multJple position switch. On four-wire products. the strobe shall be powered Independently of the sounder. The horn on horn/strobe models shall operate on a coded or non-coded power supply. Outdoor Products SpectrAlen Advance outdoor horns, strobes and horn/strobes shall be listed for outdoor use by UL and shall operate between minus 40 degrees and 151 degrees Fahrenheit. The products shall be listed for use with a System Sensor outdoorlweatherproof back box with half Inch and three-fourths Inch conduit entries. Synchronization Module The module shall be a System Sensor Sync.Clrcult model MDL listed to UL 464 and shall be approved for fire protective service. The module shall synchronize SpectrAlert strobes at 1 Hz and horns at temporal three. Also. while operating the strobes, the module shall silence the horns on horn/strobe models over a single pair of wires. The module shall mount to a 4"/16 X 4"/.. X 2lfe-inch back box. The module shall also control two Style Y (class B) circuits or one Style Z (class A) drcuit. The module shall synchronize multiple zones. Daisy chaining two or more synchronIZation modules together will synchronize all the zones they control. The module shall not operate on a coded power supply. Phy,lC ..I/Electrtc.ll SpeCifications Standard Operating Temperature K Series Operating Temperature Humidity Range Strobe Flash Rate Nominal Voltage Operating Voltage Range2 Input terminal wire gauge Ceiling mount dimensions (Including lens) Wall mount dimensions (Including lens) Hom dimllllSlons Wall-mount back box skirt dimensions (885-2, BBSW-2) Ceiling-mount back box skirt dimensions (B8SC-2, BBSCW-2) Wall-mount weatherproof back bolt dimensions (SA-WBB) Ceiling-mount weatherproof back bolt dimensions (SA-WBBC) Notes: 1. Full Wave Rectified (FWR) voltage Is a non-regulated, time varying power source that is used on some power supply and panel outputs. 2. P. S. PC, and SC products will operate at 12 V nominal only for 15 and 15f75 cd. 32'F to 12O"F (0"( to 49"C) -4O"F to 151 OF (-40'C to 66'C) 10 to 93% non-condensing (Indoor products) 1 flash per second Regulated 12DCIfWR or regulated 24DC/FWR' 8to 175V(12VneminaO or 16 to 33 V (24 nominal) 12 to 18AWG 6.S- diameter x 25- high (173 mm diameter x 64 mm high) S.61. x4.7'W x 25"0 (142 mm Lx 119 mmWx64 mm D) 5.61. x4.TWx 13'0(142 mm Lx 119mmWx33mm D) 591. x 5.0'W x 2.2'0 (151 mm Lx 128mmWxS6mm D) 7.1 "diameter x 2.2S-hlgh (180 mm dlameterx 57 mm high) S.71. x 5.1 'W x 2.0'0 (145 mm L x 130 rnm W x 51 mm D) 7.1-diameterx2.0-high (180mm diameter x 51 mm hIgh) A05-o395..('03.