|
<br />
<br />@
<br />
<br />GAF MATERIALS
<br />CORPORATION
<br />
<br />APPLICATION INSTRUCTIONS
<br />
<br />~~~~~~~""~.~r~~~"'-'-- -.4...~...__""'- _t:'~_ n.:...o.;....:__IUL-.. ....-_ rw........,...,.-~_...__.-........ ____......-"-....-n1.~~r.""''"'''~..;:<.~.~.........~,_t(_,~~
<br />
<br />Timberline~ Series shingles come
<br />in either 36" (914mm) or 36-15/16"
<br />'(938mm) lengths, depending on
<br />shingle brand, Application instruc-
<br />tions apply to both,
<br />
<br />f-- - ,- - 36" (914mml
<br />
<br />
<br />f. 1-- ""~,, ,.",-".-.
<br />
<br />\ 11.112" (2nnlill)
<br />-+-'2,112" (318mm)' ~
<br />
<br />1 (~5/1Hn) . '.1/2" (3amm) --~
<br />
<br />1, 1/2" (38mm)
<br />
<br />- I
<br />
<br />'2"
<br />(30-lmm,
<br />I
<br />
<br />I
<br />-1-1
<br />
<br />I
<br />
<br />GENERAL /NS-rRtJC.r/ONS --- "
<br />
<br />. ROOF DECKS: For use on new or reroofing work~ver well.seasoned, supported wood deck,
<br />tightly,constructed with maximum 5" (152mm) WI?e lumber, haVing adequate natl,holdlng
<br />capacity and smooth surface Plyv,ood decking as recommended by The" Engineered Wood
<br />Assn i!> acceptable, Plywood decks for Class A Installations must be 3!H (10mm) thiCk, or
<br />yrealer with underlaymenls as noted below Shingles must not be fastened directly to insulation
<br />or insulated deck unless authorrzed In writing by GAF Matenals Corporation, Roof decks and
<br />eXisting surfacing material must be dry prior to applitation of shingles", ,
<br />. UNDERLAYMENT: Underlayment beneath sl1ingl~s has many benefit,S, Includ,lng preventing
<br />'Nind driven rain from reaching the lntenor of the building and preventll1g sap In some wood
<br />decking from reacting with aspnalt shingles Underlayment is also required by many code bod.
<br />les, Consult your local building department for ItS requirements Where an underlayment 15 to
<br />be Installed, a breather,type underlayment such as GAFMC's Shingle,Mate'underlayment IS rec,
<br />ummended Underlayment must be II1stalled flat. WI\i)OUt wnnkles, '. ' ,
<br />. FASTENERS: Use of nails is recommended, (Staple speCifications and application
<br />Instructions are available from GAF Materials Corporation, Contractor Services Dept. 1351
<br />Alps Road, Wayne, NJ 07470) Use only zinc coated steel or alumll1um, 10.12 gauge.
<br />barbed, deformed or smooth shank roofing nails with heads 3/8" (10m;n) to 7/15" (12mm)
<br />In diam<:ter. Fasteners should be long enough to penetrate at le~st 3/4 (19mm) Into wood
<br />decks orjust through the plywood decks Fasteners must be driven flush.lVlth the surface
<br />of the shingle, Over driving will damage the shingle, Raised fasteners ~llIlnterfere With the
<br />sealin9 of tne shingles, For normal installation, four fasteners must be Installed per shll1gle,
<br />a nominal 5.5/8" (143mm) up from the bottom of the shingle, to penetrate both layers of
<br />..~ the-shlngle,- Fasteners musLbe...lnstalled_ approximately..J :::_1_112'- (25:38mlJ1) _aIld
<br />11-112",12 -1 !2" (292-318mm) from each side, ,
<br />. WIND RESISTANT: These shingles have a s~ecial thermal sealant that firmly bonds ltle
<br />shingles together after application when exposed fO sun and warm temperatures Shingles
<br />instaDed In rail or Winter may not seal untlllhe folb/llng Spring, If shingles are damaged by Winds
<br />
<br />These shingles must be nailed a
<br />nominal 5.5/8" (143mm) from bottom
<br />of shingles, as shown, to allow for
<br />penetration through the double ply
<br />area just above the tabs Nails should
<br />remain unexpos~d,
<br />
<br />. I I
<br />15'5;~" I ~43mmJ
<br />nommal unt:xposca
<br />i and U,(cugh
<br />I ""Ih '.,eos
<br />,
<br />
<br />
<br />Statluard NaHlrwJ ?al\arn ' fO\J:f" naJJs p&r ::it'llngle
<br />
<br />... .." _T'
<br />
<br />...a-_..
<br />
<br />~
<br />
<br />r ~--.. ...
<br />
<br />('j Underlayment: Standard SloPe-4~12 (333mm/m) or n:ore ,
<br />, Application of underlayment; Cover deck With one layer of underlayment Installed, Without
<br />Wrinkles Use only enough nails to hold underlhment In place untlf covp.red by sfllngles
<br />Application of eave flashing: fnstall eave flashing sych as GAF Materials Corporation Weather
<br />VI/atc\)" or StormGuard" LeaK Barner In locailtles whrre leaks may be caused by ':vater backing
<br />up behind ice or debris dams Eave flashing must overhang the roof edge by 318 (10mm) and
<br />extend 24" (61Omm) beynnd the inside waif line I
<br />
<br />4" i1Q2mmi~ ,. _ Deck
<br />12-(305mm) y:'---~_~__
<br />Mlnlmur:1 SIope,0 ~,>;~
<br />For lower slopes see Sex 1a ,'-~~/,-:./?-
<br />~:,
<br />. .-~::.-
<br />
<br />
<br />Weather Walcl1'
<br />or StormGuaro'
<br />leak a"rrier
<br />
<br />r-
<br />
<br />Ail sheets are 36" (914mm)
<br />.vIde Shingle,Male"
<br />undef1aymenl.
<br />
<br />4" (102mml End lap
<br />
<br />Aiong rake, place
<br />drip edge on lop
<br />of under',aYn'enl
<br />
<br />Along eaves put underlayment
<br />on 100 01 metal drip edge
<br />
<br />4"'3 Underlayment: Low Slope 2/12-4/12 (167mm-333mm/m)
<br />,~ Application of underlayment and eave f1asring: Completely cover the deck With two
<br />layers of underlayment as shown, Use only ~nough nails to hold underlayment in place
<br />until covered by shingles, Use blind nailing for eave flpshings At eaves and where ice dams Cen
<br />be expected, use one layer of GAF Materials corporat~on Vfcather Watch' or StormGuard" Leak
<br />Bamer, Eave flashing must overhang Ihe roof cd e y 3!8" (10mm) and extend 2'1" (610mm)
<br />beyond the II1side wall line, Wllere ice dams or de~ri. dams are not expected, install 2 plies of
<br />Shlngle.Mate' unflerlaYJ11ent
<br />
<br />Low siope
<br />2' to 4" L--_
<br />(Slrrlln '0 102mm) ~
<br />12" (305mm)
<br />
<br />
<br />All sheets are 360 (914mm)
<br />Hide Shingle,Male'
<br />'Jnderlaymenl , J
<br />
<br />Rake dnp edge
<br />
<br />3i8" (lOmm) Rool overhang
<br />
<br />2
<br />
<br />Starter Course
<br />Apply as shown
<br />
<br />StaC't at either rake and
<br />!ay ;" eithe' direction
<br />
<br />
<br />Non,corroding
<br />Mp.tal Drip Edge
<br />'\
<br />
<br />For m3:1:Inlum wine! resist~nc9
<br />along rakes. cement shing1es
<br />10 underlayment and oach
<br />other 'n " 4" (102mm) widlh
<br />of ;:'lSDh~ll plastic r(){)f cement
<br />
<br />P'aca shingle 3i8" (lQmm)
<br />ever eave and rake edges
<br />10 provide drip edge
<br />
<br />Trim tabs off al\ s\after course
<br />shingles, lhen place and nail
<br />as shown, 3- to 4" (76mm tn
<br />l02rnm) from ert'ie
<br />
<br />3
<br />
<br />,
<br />
<br />I
<br />
<br />I
<br />
<br />First Course I
<br />Start and continue Nith full shingles laid flush fvith the starter course, Shingles may he
<br />laid from left to right or right to left. DO NOT lay shingles straight up the roof since this
<br />procedure can cause an incorrect color blend t the roof end may damfiqr. thr. shingle<;
<br />
<br />
<br />I
<br />
<br />Place Shm91€~
<br />close l~eU1ef but
<br />dor. t Clc'Hd
<br />
<br />
<br />Conti r'l ue
<br />~rst COUfS.o?
<br />. ,....,lh.....t-ol<'l
<br />I 3ringiE'li
<br />
<br />SI;H1 ~rs~lco'..'[se -!-11th wnc1e s,";ng;~ p{<1C~d 3,'8~ (10~fT1)
<br />:;v€r p.aY~ (l/l(j ~~~~ f"(lges 1n pfnvide diip p{j()~
<br />i
<br />
<br />-~
<br />
<br />8" (203mm) . 9" (229mm) ~\
<br />
<br />I U" (356mm)
<br />- 15'. (381mm) ... ~
<br />I-+-' -'-- ~
<br />, (25mm}. 1,"~" (38mm)-~
<br />
<br />Re-Roofing
<br />If old asphalt sning[es arc to remain in place, nail down or cut away all loose, curled or lifted shin.
<br />gles: replace with new: an~ just before applying the new roofing, sweep the surface clean of all loose
<br />BebrlS, Since any Irregularities may show through the new shingles, be sure the underlying shingles
<br />prOVide a smooth surface, Fasteners must he or sufficient lengtfi to penetrale tl,e wood neck at leilst
<br />311' (1 9mm) or Just through ply.'1ood, Follow other above instructions for applicatiOf1,
<br />NOlf? Shingles can be applied over wood shingles wt:en precautions have been taken to provide
<br />an acceptable smooth s~rface: This includes cutting back old shingles et eilves and rakes and
<br />Installing ne'N wood edging strips as needed, Make surface smooth and use beveled wood strips
<br />If necessary, Install tt30 underlayment to maintain Class A rating
<br />
<br />r1lis ~roducl IS SOld with an express LIMITED WARR^NTY only, ^ co~y 01111e LIMITED WARRANTY stating I(S
<br />terms and reSl,lcllons IS pnnted on the product wrappC' or may be obl~ineC from Ihe d,<;lributor of II;[s product or
<br />dlrpctly [rom GAr Materials Corporilllon My (Ievi~tlrn Irom prinlcd Instructions shall be the resoonSlblllty 01
<br />~pnl;r.~lor "noh, 'f1i'"rrl
<br />
<br />
<br />. I
<br />
<br />I 5,5;8" (143mm)
<br />: nominal unex;Jo~l::!d
<br />I and Ihrough
<br />both la,"rs
<br />
<br />\
<br />\
<br />\
<br />\ Nail Gvi(,Ja
<br />Lll,e
<br />
<br />
<br />SIX ".Ii P altern
<br />
<br />-
<br />
<br />.... # J'oill. <111..,.- ............ "9>__,,,
<br />
<br />" ....---.-.
<br />
<br />....,~_.... ---
<br />
<br />.-.a:'1:"""~~~
<br />
<br />-
<br />
<br />~~
<br />
<br />before sealing or are not exposed to adequate surface temperatures, or If tr,e self.sealant gets
<br />dirty. the shingles may never seal. Failure to seal under 1I1ese circumstances results from the
<br />nature of self.seallng shingles and is not a manufactuflng defect To Insure Immediate sealing,
<br />apply 4 quarter-sized da~s of Sl1in~le tab adhesive on the oilck of the shingle 1" (25mm) and 13"
<br />(330I1lm) in from each Side and 1 (25mm) up from bottom of the shingle, TIle shingle must be
<br />pressed firmly into the adhesive, " ,
<br />NOTE: Application of excess tab adheSive can cause blistering of Lhe shingle
<br />For maximum Wind resistance along rakes, cement shingles to underlayment and each other In
<br />a 4" (102mm) width of asphalt plastic roof cement , '
<br />NOTE The film strips on the back of each shingle are to prevent sticking together of tJ1e slllngle:>
<br />"mile in the bundle, Their removal IS NOT required' dunng application,
<br />. CANADIAN COLD WEATHER APPLICATIONS: CSA 1215.M90 mandate!> that sl11n.
<br />91es applied between September 1 and April 30 shall be adhered with a compatible field,applied
<br />adheSive, See Wind Resistant for GAF Materials Corporation's recommendations for the appli-
<br />cation of that adhesive,
<br />. MANSARD AND STEEP SLOPE APPLICATIONS: For roof slopes greater than 21"
<br />(1750mm/m) per foot (do NOT use on vertical side walls), shingle sealing must be enhanced by
<br />hand sealing, After fastening the shingle in place, apply 4 quarter. sized dabs of shingle tab adl1c-
<br />sive as inr1icated in Wind Resistant above The shingle must be pressed firmly Into the adheSive,
<br />. EXPOSURE: 5" (127mm)
<br />. THROUGH VENTILATION: All roof structures must be prOVided wilh through ventilation to
<br />prevent entrapment of moisture laden air behind roof sheathing, Ventilation provisions must at
<br />least meet or exceed current FHA" H,UD, or local code minimum requirements,
<br />. NON-CORROOIN<rMETALORIP'EDGES:Recorrlmenaedai0i1grak'e al1d eave-edges on-- ._'U_
<br />all decks, especially plywood decks
<br />. ASPHALT PLASTIC CEMENT: For use as shingle tab adhesive Must conform to ASTM
<br />D4585 Type I or II.
<br />
<br />Precautionary Notes
<br />Timberline" Series shingles are fiberglass, self'sealing asphalt shtngles, Because of the natural
<br />characteristics of \Ile high quality waterproofing metenal used. these shingles will he stiff in cold
<br />weather and fleXible in fiot weather.
<br />1 Bundles SllUUld nut be dropped on cdge nor should attempt be made to separate shingles by
<br />"hrri1king" over ridge or other bundles,
<br />2 HRndle carefully, Shingles can easily br. brcken in cold weather or their edges damaged in 110t
<br />weather
<br />3 All exposed materials must be of Class A type
<br />4 Storage should be in a covered, ventilated area-maximum temperature 110'F (430C) Store
<br />on flat sur face and use weight equalization boards If pallets are to be double stacked,
<br />Shingles must be protected from weather Nhen stored at job site, [)o not store np.ar stefim
<br />pipes, radiators, etc, or in sunlight. All rolled product must be stored on ends
<br />5 If <;hingles are to be applied dUTlng PROLONGED COLD periods or in areas where airborne,
<br />dust or sand can be expected before sealing occurs, the shingles MUST be hand sealed
<br />See Wil1,d Resistant instructions
<br />
<br />4 Second Course
<br />Start and continue second course as shown, Trim 5" (152mm) from Lhe end of the
<br />!>hingle, Position the shingles in the second and subsequent courses flush w:th the tops
<br />of [[le wi,de cutouts, This results in a 5" (127mm) exposure, Continue with full wldtl1 shingles
<br />across tne roof, Stflke a chalk line about every 5 courses to check parallel alignment 1'11[[1
<br />eaves, NOTE Shingles may be laid from either
<br />left or fight hand Side, Start at either rake
<br />edge w:tn shingles having 6" (152mm)
<br />trimmed from rake
<br />
<br />B Wall Flashing (Sloped Roof to Vertical Wall)
<br />
<br />'-'''"'", l,l- Siding
<br />
<br />5" (127mm) 'vi;"
<br />
<br />
<br />I T ~etal Flasr'''g
<br />"'" (Na,'ed '0 the deC1<, nollo/e't'cal s,de...-aH)
<br />
<br />
<br />
<br />- ~~"",~,., CapSh!r,g'e-DoNotNail
<br />~____lnS,\all w'th Rocnng Cecr,enl
<br />
<br />"~ ~ Roonng Cement
<br />
<br />___ Shng:e
<br />-+-- Roof Deck
<br />
<br />
<br />Trim Sr,lngll.:-l!
<br />6. {\52mrr.;'
<br />
<br />5
<br />
<br />Third Course
<br />Trim 11" (279mm) from the flr~t sl1ingle in tile course then continue \^iltll full shingles
<br />across lt1e roof
<br />
<br />CMck.e I on
<br />t'iigh ~id(t 01
<br />cruml"1ey
<br />
<br />9
<br />
<br />Chimney Flashing
<br />
<br />
<br />
<br />~~nn-(:orrTll1lnQ metal t;,se nashing
<br />One piC'!ce S',pp nasi'1inQ for e;;sct1 ,=o'.Jf'se
<br />Cement in place ~:'Id nai,1 'Nlth '2 ~la115
<br />Bnnd o"e~'f11"'19 s~ingie1 ,.... asol"atl
<br />DI~!'.Hc cement
<br />
<br />",\
<br />
<br />. <).I'f.. . ,
<br />
<br />\'," ...'
<br />, -,
<br />, , ,
<br />\. \. ... '\
<br />, ".' ,
<br />'\ ,. '\ .,
<br />I' '\, ...
<br />
<br />
<br />;:Ifflmud S!",lngles.
<br />
<br />6
<br />
<br />Fourth Course and Remaining Courses
<br />Irim 17' (432 111m) from first shingle in lhe course. then continue With tull shingles across
<br />the roof FlfU1 and subsequent courses repeal full shingle Instruction) from Step 3
<br />
<br />10 Valley Construction-Closed Cut
<br />
<br />
<br />Genter full H1o:tl rOll
<br />01 Wca:,,"'lef,Vatctl.
<br />C( Slorm(;\.'at~ ____
<br />Leak. '3an-icf (0" (\ 521T'fT1!
<br />~n<1I."lpc;) in \loJl~y
<br />
<br />vane.,. Ccn~(>r1if'\e
<br />
<br />E;d:a fil'Slcf1cr ir
<br />el'd 01 sninq10
<br />
<br />,
<br />,
<br />,
<br />,
<br />/-
<br />
<br />
<br />~un stiV~e-r Ship al'd first
<br />sh.ingj@: COlJf sQ en!y acros s
<br />'tn/l{'y . 2'" (JOSml1"') rT"ir,.r'f\vl"l'
<br />
<br />FdHl CQur~e
<br />Full S~:ngle
<br />
<br />..
<br />
<br />NO fastc"lcrS "",Ul1n
<br />6~ (152~mi 01 cOll'.e!:ine
<br />
<br />Fourtll Cours<:
<br />
<br />E..tlend 8M shll1o;:e
<br />Bit fS<'lst , 2- n05mm)
<br />beyont1 ~F\r.e'Y renladir,A
<br />
<br />C:;ppe-d crXflef' se!
<br />in roofing ~el~.ef'1!
<br />
<br />:r::1lnled Shlflgle~
<br />
<br />1 Hip and Ridge
<br />For Single lay<:r application, use hip and ridge shingles and apply oS ~hol'ln To er,hance
<br />appearance, use GAF TIMBERTEX' or a double layer application of Universal Hip & Ridge
<br />(One bundle of TIMBERTEX' Hip & Ridge covers 20 lineal fl-6,1 meters,) For double application,
<br />start with triple thickness of precut Hip & Ridge shingles and continue remainder with double
<br />thickness, fasten in same manner as single applicalion sllown Apply laps away frorn prevailing
<br />Wind direction
<br />
<br />11 Valley Construction-Open
<br />
<br />O.x;)CSUiS
<br />
<br />Nail 5-5ia" (143mm;
<br />from bol1om and
<br />1" (25mm) from edge
<br />
<br />
<br />Ic-p !1fv<J;1~.,. f). ',152I"lml
<br />......'de ~lw(:'cn sbl'o;les
<br />SDr~a.::t. tiS"; 1 Gmf;1/'r,,;
<br />pot root !c'm\rr1 e;\,<"~
<br />
<br />Can:e' h.:lI....;dt'h rcd
<br />01 vV!:atller 'N,,~c:-," Cf
<br />SlorlT'G("jar'O''' Le~k n<\'u.r
<br />(6.1,152~.rr.\ end ',10'<;1
<br />;n v~lJey
<br />
<br />Sc<u!e I"~ ft1el.ll 0.JS!11119
<br />"""U"ClJt plJr<t....nf17 by r.JfI1:;P';
<br />rQ0{,ng r"Jd'S C''-~')' 1 r l(l 1~-
<br />6g~Ojl\;~'t~~~~~:~~~'9 cd~(1
<br />l~le~.1l .. .l::.f>y
<br />
<br />B" 1203mrn) eXPO,Ur~
<br />
<br />Cer-,ler 2Q":S08/1lm)
<br />Me.. ro"~<;onodi"g.,
<br />:~a~t~n:~le;'~ ~a'.I~e
<br />Minlrrum 4' (1C2rT'iM)
<br />'.If'\C,flf !hll"c{e, <\1 !'!4'.e
<br />
<br />Emoc'J sJlill~l€<; 't"
<br />- - - - ')"01'.'11 rja!;~\c
<br />>:e""'cn!;.., ...,:),1e.
<br />
<br />Bend H,p & Ridge shIngle
<br />centered over Hip or Ridge
<br />
<br />
<br />~-A .~
<br />
<br />
<br />S' (127mrni t
<br />
<br />ROOF DL\.PIIRA.wI NAILING SCIIEDULE
<br />
<br />K'IO~~ uJ~
<br />~
<br />
<br />
<br />~
<br />ti)
<br />~
<br />\f
<br />
<br />RI l7t, ~ LI JE::.
<br />
<br />120 wIPII 3 SECOND GUST EXPOSURE "B" \VIND ZONE
<br />
<br />3d Common Nails @ 6" o,c. & --l" a.c. @ Gabie End W:111 or Gabie Truss
<br />,13 Ix 2 '12" Long Gun n:1i I @ --l" o.c,
<br />,120 x 3" LDng Gun n:1il @ --l" o,c,
<br />,113 ,'( 2" Long Gun nail @ 3" o,c,
<br />-n----.09C'-----x.2 1~..tangGu]'fnjjr@ 3"o~C-~- _.~- ---,
<br />
<br />~
<br />
<br />120 wIPII 3 SECOND GUST EXPOSURE "B" \VIND ZONE
<br />
<br />8d Common Nails @ 6" o.c, Edges & 8d Common Nails @ 12" o.c. Intennediate
<br />,131 x 2 '12" Long Gun nail @ -1" o,c. Edges & S" o.c. Intermediate
<br />,120 ,x 3" Long Gun nail @ r O.c, Edges & S" o,c, Intermediate
<br />,113 x 2" Long Gun nail @ 3" o,c, Edges (Staggered) & S" o,c, Intem1ediate
<br />,099 x 2 W' Long Gun nuil @ 3" o,c Edges & S" o.c, Intennedi:1te
<br />
<br />I
<br />
<br />I
<br />
<br />NOTES:
<br />
<br />1,) See Structural Notes for sheathing specific:ltions and wind speed.
<br />2,) End joints of the roof sheathing shall be staggered and occur over fraITIlng member,
<br />3,) Schedule assumes she:1thing is fastened directly to Southern Yellow Pine or Douglas
<br />Fir or better,
<br />
<br />1 1/2' SAW.CUT SLOT
<br />SHY SlOT 12' SHOflT OF
<br />Mf( RI[)GE END.
<br />INTERSECTION
<br />AND/<::xl 08SmUCnOO,
<br />
<br />NOTES:
<br />· END CAPS TO BE LOCATED
<br />OVER EXPOSED ENDS OF
<br />FIRST AND lA5T SECTla-lS,
<br />CAUlK BETWEEN BOnOM
<br />EDGE Of END CAP AND ROOF,
<br />
<br />· INSTAll RIDGE VENT CONT.
<br />n-u: ENTIRE LENGTH OF RIDGE,
<br />
<br />· RIDGE VENTS SHOULD N.WAyS
<br />BE INSTAlLED WlTH SOfFITI
<br />EAVE INTA.l<ES a: EQUAL
<br /><X{ GREA]ER MEA.
<br />
<br />· REFER TO MANUFACTURER'S
<br />DCTNlS ANS SPECS.
<br />
<br />I
<br />
<br />~
<br />I
<br />J
<br />
<br />
<br />METAl. ROOF CAP
<br />TO MATCH METAl ROOF
<br />
<br />C<X{AVENT RJDGE
<br />VENT on SIMIl.AJ\
<br />(TO MATCH ROOF SLOPE)
<br />
<br />NNLS TO BE LONG
<br />ENOUGH TO PENETRATE
<br />VENT AND ROOf
<br />SHEATHING; NAIL HEAD
<br />SHOULD BE FLUSH 'IvHH
<br />TOP OF SHINGLE,
<br />
<br />1/2' EXT.
<br />PL YVlooO
<br />
<br />PRE. ENGINEERED
<br />ROOF mUSSES
<br />
<br />RIDGE VENrr INSTALLf\TION DETAIL
<br />
<br />SCALE: N.T.S,
<br />
<br />
<br />REVISION BY
<br />
<br />~
<br />U
<br />W
<br />~
<br />I
<br />U
<br />er.::
<br /><t:
<br />
<br />L[)
<br />"
<br />---
<br />CO
<br />I
<br />to
<br />CO
<br />N
<br />
<br />~
<br />r<)
<br />---
<br />CO
<br />'-.-/
<br />
<br />"'
<br />
<br />2
<br />o
<br />if)
<br />er::
<br />w
<br />I
<br />
<br />I
<br />0...
<br />r<)
<br />N
<br />to
<br />r<)<D
<br />r<)'"'
<br />'"'
<br />.-
<br />___<I
<br />r<)o<D
<br />r<) rv-~
<br />...j-U-,-...
<br />1"'\.1 0 t<)
<br />I. ~ ---1 ro
<br />xlL.'--"
<br />
<br />g<~
<br />o..~
<br />.2"'-
<br />.~<x
<br />I o...~~
<br />
<br />er::
<br />-w
<br />>-
<br /><t:
<br />I
<br />~
<br />
<br />~1
<br />
<br />,1,'';'~":
<br />
<br />i~
<br />
<br />"'~ ~1 ~]
<br />I
<br />[~
<br />~ ~ [U
<br />I ~ I ~3::~
<br />flj
<br />~] I ~j
<br />i>"~
<br />I "",;~
<br />~";,o
<br />~1 ~] ~l
<br />"'.~
<br />t~T
<br />~"j ~~
<br />ti.l
<br />
<br />~~
<br />~lj
<br />
<br />~~
<br />
<br />~~
<br />
<br />~
<br />
<br />~
<br />
<br />00";;) ,"",~
<br />~~
<br />
<br />~~
<br />~-:~;,!
<br />t:tl
<br />
<br />r~.i f~ ~~~
<br />".,i,'~~ ",,;.j <;"!.,j
<br />~J if:~ kg
<br />
<br />@ COPYRIGHT, 2002
<br />H. TI-iAYER HERSOM, ARCHITECT
<br />AND ASSiGNED OTHERS, NO
<br />UNAUTHORIZED USE OF ANY
<br />PART OR ENTiRE DRAWING AS
<br />PRiNTED ON TI-iIS SHEET.
<br />
<br />DRAWN
<br />CHECKED
<br />HTH
<br />DATE
<br />SCALE
<br />AS NOTED
<br />JOB NO.
<br />SHEET
<br />8=4
<br />
|