Laserfiche WebLink
<br />Gamewell <br />..-::'71 FIRE CONTROL <br />~ INSTRUMENTS <br /> <br />DACT-E3 <br /> <br />by Honeywell <br /> <br />Description <br /> <br />The Digital Alarm Communicator Transmitter (DACT-E3) is <br />an optional component of the E3 Series 1M Expandable <br />Emergency Evacuation System. The DACT-E3 sends digi- <br />tal signals over the telephone network to a central station. <br />This module can be located in the main cabinet or remotely <br />located via a local RS-48S serial interface. <br /> <br />Digital Alarm <br />Communicator Transmitter <br /> <br />. 3+1 2300 Hz <br />. 4+21400 Hz <br />. 4+2 2300 Hz <br /> <br />,..U'~"' ~,~ ~ <br />~~- <br /> <br />- -. ~;:::::: <br /> <br />;,:~~~.. -~~~Il:~l <br /> <br />....'~'"' - . _ "'l(!I._"'" <br />- . <br /> <br />-~ -~ ...... if'~ 1~ ....__ ' <br /> <br />i- .~~:t <br /> <br />The DACT-E:~ is compatible with digital alarm communica- <br />tor receivers (DACRs) that receive the following signaling <br />formats: <br />. SIA DC8 <br />. SIA DCS20 <br />Ademco Contact ID <br />3+1 1400 Hz <br /> <br />'- <br /> <br />In addition to the DACT-E3 being compatible with digital <br />signaling formats, the DACT-E3 features numerous for- <br />mats for communication to a central station. As a digital <br />communicator, the DACT-E3 complies with FCC Part 8, <br />Telecommunication Standards for DC and AC Ringer <br />Equivalence. <br /> <br />, <br />"!il <br /> <br />DACT-E3 <br /> <br />Features <br /> <br />Installation Instructions <br /> <br />. Listed under UL Standard 864, 9th Edition. <br />. Communicates with the E3 ILI-MB-E3 sub-assembly via <br />RS-485. <br />. Communicates in a variety of formats. <br />. T:-ansmits and verifies data to the central station. <br />. Offers pre-programmed dialing to the central station <br />pllone number. <br />. Performs on and off-hook status to the phone lines.' <br />. T-aces proper central station "ACK" and "Kiss-off" tone. <br />. Activates hang-up and release phone lines. <br /> <br />The DACT-E3 is adaptable for installation in standard E3 <br />Series 1M system cabinets.. Typically, the DACT-E3 module <br />mounts on standoffs on top of the left side of the ILI-MB-E3 <br />module. Either unit can be easily connected to the backbox <br />or sub-assembly plate depending on the cabinet module. <br /> <br />Note: For instructions on in:5talling the DACT-E3, refer to <br />the E3 Series 1M Expandable Emergency Evacuation Instal- <br />lation/Operating Manual, Part Number: 9020-0574 or the <br />DACT-E3 Installation Instructions Part Number:9000- <br />0580.. <br /> <br />Specif:ications <br /> <br />Ordering Information <br /> <br />Operating Voltage: 24 VDC <br />(from PM-9 power supply) <br />Operating Current: 0.018 amp <br />Alarm Current: 0.018 amp <br />Operating Temperature: 320 to 1200 F (0 to 490 C) <br />Relative I-Iumidity: 0 to 93%, non-condensing at <br />900 F (320 C) <br />E3 Series"" and NetSOLO"" are trademarks of Honeywell Intemationallnc. <br /> <br />Model <br />DACT-E3 <br /> <br />Description <br /> <br />Digital alarm communicator transmitter <br /> <br />An ISO 9000-2000 Company <br /> <br />I ~~~~I ] <br />12 Clintonville Road, Northford, CT 06472-1610 USA. Tel: (203) 484-7161 . Fax: (203) 484-7118 <br />I Speclflcaoons are for information only, are not intended for Installation pUrposes, ~d are subJl!ct to change without notice. No responsibility is assumed by Gamewel~FCI for their use. "', <br />(" @2006 Honelwelllnlemationallnc. All rights reserved. www.gamewell-fci.com 9020-0610 Rev. E page 1 of 1 <br /> <br />SIGNALING <br /> <br /> <br />@ <3>MEA:.,' ~ Ckyof <br />LISTED ......OVI!D Approved " Appro."" Ottnvor <br />51869 3025415 231..o6-E 7165-06,..:261 g::: ~ Approved <br />7165-0694:269 HIgh RIae <br />