Laserfiche WebLink
<br />2 I D192C Notification Appliance Circuit Supervision Module <br /> <br />Planning <br /> <br />Wiring <br />Use a Class B, Style W, two-wire circuit and wire according to the <br />instructions supplied with the module. For UL applications, use <br />a UL Listed regulated power supply to power notification devices <br />through the D 192C Module. <br />To comply with NFPA Standards: <br />The control panel and power supply must be supervised <br />or installed in the same room not more than 20 ft (6 m) <br />from the DIne. <br />, Wiring between the control panel and the power supply <br />must be in conduit. -, . <br />, Power supply fault conditions must be supervised by a <br />UL Listed relay. <br /> <br />Notification Appliances <br />Notification Appliances used with the D192C Module: <br />. Must be polarized (DC) equipment. <br />Must match the voltage rating of the alarm power <br />supply. <br />Must not exceed the current rating of the alarm power <br />supply. <br />. Must not exceed 1.8 A in combined device current for <br />each Dlnc Module. <br /> <br />~ <br /> <br />Hardware Accessories <br /> <br />0137 Mounting Bracket <br /> <br /> <br />Use to mount accessory modules in D81 03, <br />D8108A, D8109, and D8109L Enclosures. <br /> <br />0138 Mounting Bracket, Right Angle <br /> <br /> <br />Use to mount accessory modules in a D9101 <br />Enclosure. <br /> <br />Bosch Security Systems <br /> <br />t <br /> <br />For more information please visit <br />www.boschsecuritysystems.com <br /> <br />Modifications reserved I 75-0706 1-00G-F I <br /> <br />D9142F 24 VDC Auxiliary Power Supply <br /> <br />. .... .. The D9142F is a UL Listed, Auxiliary Power <br />. II Supply for use in Commercial Fire Alarm <br />. ... System applications. It provides up to four <br />. amps for charging batteries and for powering <br />auxiliary or indicating devices. The D9142F <br />is provided in its own red enclosure and with <br />a D 160 1 Transformer to provide power to <br />both the D9142F and to the control panel. <br /> <br />Technical Specifications <br /> <br />*'~I:?~!t';:t_~~/M~II~I~iU'l'li.'j~r.f.i\i~ml' Jj ... <br />Compatible Control 2000 Series, 08112, 0911281, 0721281, <br />Panels 09412G, 07412G, D7212G, D9412, D9112, <br />09412, and D7212 <br />AUX PWR IN: 12 VDC supplied by auxiliary <br />power from the control panel. <br />EXT PWR IN: 12 VDC or 24 VDC supplied <br />by Ul Listed external power supply, or <br />12 VOC supplied by the alann output <br />terminal on the control panel. Module is rated <br />at 1.80 A output at 12 VDC or 24 VDC, <br />Idle: 25 mA <br />Alarm: 50 mA <br />Maximum rating of module alann circuit is <br />1.80 A. <br /> <br />D192C Operating <br />Voltage <br /> <br />Alarm Output <br /> <br />Voltage <br /> <br />0192C Module <br />Current <br /> <br />Dimensions <br />(H x W x D) <br />Indicating Circuit <br />End-of-line (EOl) <br />Resistor <br />0105Fl EOl <br />Resistor <br /> <br />Power Supplies <br /> <br />Alarm power comes from an external power <br />supply, or the control panel's output ter~;nal <br />if one is used. <br />5.0 in. x 3,0 in. x 0,75 in. <br />(12_7 cm x 76 mm x 19 mm) <br />Bosch Security Systems <br />(PIN: 15-03130-005): 560 n. 2 W <br /> <br />locate on the last D192C Module in the <br />circuit. 80sch Security Systems <br />(PIN: 15-03130-001): 1 ill <br />Use a Ul Listed auxiliary 12 VDC or 24 VDC <br />regulated power-limited power supply for fire <br />protective signal units and commercial and <br />residential burglar units. Install auxiliary <br />supply according to manufacturer's <br />instructions. <br /> <br />BOSCH <br /> <br />I <br />